ETC2 MCEPI-04 Dual in line switches - piano type Datasheet

REVISIONS
PART NO.
MCEP Series
ECN #
REV
DESCRIPTION
-
A
RELEASED
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
EPI
PCB Layout
Schematic (Typical)
2, 4, 6, 8, 10 Positions Available
Dimensions: Millimetres (Inches)
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Jagan
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
1
OF
6
REVISIONS
PART NO.
MCEP Series
ECN #
REV
DESCRIPTION
-
A
RELEASED
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
EPM
PCB Layout
Schematic (Typical)
2, 4, 6, 8, 10 Positions Available
Dimensions: Millimetres (Inches)
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Veena
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
2
OF
6
REVISIONS
PART NO.
MCEP Series
ECN #
REV
DESCRIPTION
-
A
RELEASED
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
Specifications:
Mechanical:
Maximum operating force
Operating temperature range
Storage temperature range
Mechanical life
:
:
:
:
800 gf
-20°C to +85°C
-40°C to +85°C
2,000 cycles
:
:
:
:
:
:
2,000 cycles
25 mA, 24 V dc
100 mΩ at 500 V dc
100 MΩ at 500 V dc
500 V ac/1 minute
Single pole and single throw
Electrical:
Electrical life
Rating
Maximum contact resistance
Maximum insulation resistance
Dielectric strength
Circuit
Materials:
Cover
Base
Stem
Contact
Terminal
: UL 94V-0 Nylon high temperature thermoplastic
Colour : Black
: UL 94V-0 Nylon high temperature thermoplastic
Colour : Black
: UL 94V-0 Nylon high temperature thermoplastic
Colour : White
: Alloy copper with gold cladding
: Brass with gold cladding
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Veena
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
3
OF
6
REVISIONS
PART NO.
MCEP Series
ECN #
REV
DESCRIPTION
-
A
RELEASED
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
Reflow Temperature Profile
Soldering Process:
Wave soldeing: Recommended solder temperature at 500°F ( 260°C) maximum of 5 seconds for through hole type
Hand soldering: Use a soldering iron of 30 watts, controlled at 350°C approximately maximum 5 seconds while
applying
Reflow soldering: When applying reflow soldering, the peak temperature or the reflow Oven should be set at 260°C
maximum
Do not wash the switch except top tape sealed type, which suitable for spray cleaning method from top of the s/w
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Veena
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
4
OF
6
REVISIONS
PART NO.
ECN #
REV
DESCRIPTION
-
A
RELEASED
MCEP Series
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
Specification Table
Number of
Positions
Dimensions
(A)
Dimensions
(B)
2
4.98 (0.196)
2.54 (0.1)
MCEPI-02
4
10.06 (0.396)
7.62 (0.3)
MCEPI-04
6
15.14 (0.596)
12.7 (0.5)
MCEPI-06
8
20.22 (0.796)
17.78 (0.7)
MCEPI-08
10
25.3 (0.996)
22.86 (0.9)
MCEPI-10
2
4.98 (0.196)
2.54 (0.1)
MCEPM-02
4
10.06 (0.396)
7.62 (0.3)
MCEPM-04
6
15.14 (0.596)
12.7 (0.5)
MCEPM-06
8
20.22 (0.796)
17.78 (0.7)
MCEPM-08
10
25.3 (0.996)
22.86 (0.9)
MCEPM-10
Part Number
Dimensions : Millimetres (Inches)
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Veena
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
5
OF
6
REVISIONS
PART NO.
MCEP Series
ECN #
REV
DESCRIPTION
-
A
RELEASED
DRAWN
DATE
Ashok 19/01/12
CHECKD
DATE
APPRVD
DATE
Jagan
19/01/12
Farnell
02/02/12
Part Number Explanation:
MC
EP
I
-
Type
End-Stackable
Piano Type Dip
Switch
Terminal
Type
Actuator
Type
Terminal Type
Actuator Type
Number of Positions
-
02
Number of
Positions
: I = Through Hole Type
: M = SMT Type
:
= Long Actuator
: 02, 04, 06, 08, 10 Positions
www.element14.com
www.farnell.com
www.newark.com
Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No
licence is granted for the use of it other than for information purposes in connection with
the products to which it relates. No licence of any intellectual property rights is granted. The
Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no
responsibility for its accuracy or completeness, any error in or omission from it or for any
use made of it. Users of this data sheet should check for themselves the Information and
the suitability of the products for their purpose and not make any assumptions based on
information included or omitted. Liability for loss or damage resulting from any reliance on
the Information or use of it (including liability resulting from negligence or where the Group
was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2012.
TOLERANCES:
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
DRAWN BY:
Ashok
CHECKED BY:
DATE:
19/01/12
DATE:
Veena
19/01/12
APPROVED BY:
DATE:
02/02/12
DRAWING TITLE:
Dual In Line Switches - Piano Type
SIZE
A
DWG NO.
SCALE: NTS
M10000816
U.O.M.: mm (Inches)
REV
ELECTRONIC FILE
A
EPI(M)-V_DWG
SHEET:
6
OF
6
Similar pages