MOTOROLA MCM6706CR 32k x 8 bit static random access memory Datasheet

MOTOROLA
Order this document
by MCM6706CR/D
SEMICONDUCTOR TECHNICAL DATA
MCM6706CR
Product Preview
32K x 8 Bit Static Random
Access Memory
The MCM6706CR is a 262,144 bit static random access memory organized
as 32,768 words of 8 bits. Static design eliminates the need for external clocks
or timing strobes.
Output enable (G) is a special control feature that provides increased system
flexibility and eliminates bus contention problems.
The MCM6706CR meets JEDEC standards and is available in a revolutionary
pinout 300 mil, 32–lead surface–mount SOJ package.
•
•
•
•
•
Single 5.0 V ± 10% Power Supply
Fully Static — No Clock or Timing Strobes Necessary
All Inputs and Outputs Are TTL Compatible
Three State Outputs
Fast Access Times: MCM6706CR–5 = 5 ns
MCM6706CR–5.5 = 5.5 ns
• Center Power and I/O Pins for Reduced Noise
BLOCK DIAGRAM
A
VCC
VSS
A
A
A
A
MEMORY
MATRIX
512 ROWS x 64 x 8
COLUMNS
ROW
DECODER
A
A
A
J PACKAGE
300 MIL SOJ
CASE 857–02
PIN ASSIGNMENT
A
1
32
NC
A
2
31
A
A
3
30
A
A
4
29
A
E
5
28
G
DQ
6
27
DQ
DQ
7
26
DQ
VCC
8
25
VSS
VSS
9
24
VCC
DQ
10
23
DQ
DQ
11
22
DQ
W
12
21
A
A
13
20
A
A
14
19
A
A
15
18
A
A
16
17
NC
A
DQ0
DQ7
E
PIN NAMES
COLUMN I/O
COLUMN DECODER
INPUT
DATA
CONTROL
A
A
A
A
A
A
A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Address
W . . . . . . . . . . . . . . . . . . . . . . . . . Write Enable
E . . . . . . . . . . . . . . . . . . . . . . . . . . Chip Enable
G . . . . . . . . . . . . . . . . . . . . . . . Output Enable
DQ . . . . . . . . . . . . . . . . . . . Data Input/Output
VCC . . . . . . . . . . . . . . . . + 5 V Power Supply
VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . Ground
NC . . . . . . . . . . . . . . . . . . . . . . No Connection
W
G
This document contains information on a new product under development. Motorola reserves the right to change or discontinue this product without notice.
REV 1
10/9/96
 Motorola, Inc. 1996
MOTOROLA
FAST SRAM
MCM6706CR
1
TRUTH TABLE
E
G
W
Mode
I/O Pin
Cycle
H
L
L
L
X
H
L
X
X
H
H
L
Not Selected
Read
Read
Write
High–Z
High–Z
Dout
Din
—
—
Read Cycle
Write Cycle
ABSOLUTE MAXIMUM RATINGS (See Note)
Symbol
Value
Unit
VCC
– 0.5 to + 7.0
V
Vin, Vout
– 0.5 to VCC + 0.5
V
Output Current
Iout
± 30
mA
Power Dissipation
PD
2.0
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Rating
Power Supply Voltage
Voltage Relative to VSS for Any Pin
Except VCC
This device contains circuitry to protect the
inputs against damage due to high static voltages or electric fields; however, it is advised
that normal precautions be taken to avoid application of any voltage higher than maximum
rated voltages to this high–impedance circuit.
This BiCMOS memory circuit has been designed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear feet
per minute is maintained.
Storage Temperature — Plastic
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED
OPERATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min
Typ
Max
Unit
Supply Voltage (Operating Voltage Range)
VCC
4.5
5.0
5.5
V
Input High Voltage
VIH
2.2
—
VCC + 0.3*
V
Input Low Voltage
VIL
– 0.5**
—
0.8
V
Symbol
Min
Max
Unit
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Ilkg(I)
—
± 1.0
µA
Output Leakage Current (E = VIH or G = VIH, Vout = 0 to VCC)
Ilkg(O)
—
± 1.0
µA
Output High Voltage (IOH = – 4.0 mA)
VOH
2.4
—
V
Output Low Voltage (IOL = + 8.0 mA)
VOL
—
0.4
V
* VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2.0 V ac (pulse width ≤ 2.0 ns) or I ≤ 30.0 mA.
** VIL (min) = – 0.5 V dc @ 30.0 mA; VIL (min) = – 2.0 V ac (pulse width ≤ 2.0 ns) or I ≤ 30.0 mA.
DC CHARACTERISTICS
Parameter
POWER SUPPLY CURRENTS
Parameter
Symbol
MCM6706CR–5
MCM6706CR–5.5
Unit
Notes
AC Active Supply Current
(Iout = 0 mA, VCC = max, f = fmax)
ICCA
240
235
mA
1, 2, 3
AC Standby Current (E = VIH, VCC = max, f = fmax)
ISB1
120
115
mA
1, 2, 3
CMOS Standby Current (VCC = max, f = 0 MHz,
E ≥ VCC – 0.2 V, Vin ≤ VSS, or ≥ VCC – 0.2 V)
ISB2
30
30
mA
NOTES:
1. Reference AC Operating Conditions and Characteristics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3.0 V, VIH = 3.0 V).
2. All addresses transition simultaneously low (LSB) and then high (MSB).
3. Data states are all zero.
MCM6706CR
2
MOTOROLA FAST SRAM
CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested)
Symbol
Max
Unit
Address Input Capacitance
Cin
5
pF
Control Pin Input Capacitance (E, G, W)
Cin
6
pF
Cout
6
pF
Parameter
I/O Capacitance
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to + 70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ns
Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1a
READ CYCLE (See Notes 1 and 2)
Parameter
Symbol
MCM6706CR–5
MCM6706CR–5.5
Min
Max
Min
Max
Unit
Notes
3
Read Cycle Time
tAVAV
5
—
5.5
—
ns
Address Access Time
tAVQV
—
5
—
5.5
ns
Chip Enable Access Time
tELQV
—
5
—
5.5
ns
Output Enable Access Time
tGLQV
—
4
—
4
ns
Output Hold from Address Change
tAXQX
2.0
—
2.0
—
ns
Chip Enable Low to Output Active
tELQX
3
—
3
—
ns
4 ,5, 6
Chip Enable High to Output High–Z
tEHQZ
—
3
—
3
ns
4, 5, 6
Output Enable Low to Output Active
tGLQX
0
—
0
—
ns
4, 5, 6
Output Enable High to Output High–Z
tGHQZ
—
3
—
3
ns
4, 5, 6
NOTES:
1. W is high for read cycle.
2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus
contention conditions during read and write cycles.
3. All read cycle timing is referenced from the last valid address to the first transitioning address.
4. At any given voltage and temperature, tEHQZ max < tELQX min, and tGHQZ max < tGLQX min, both for a given device and from
device to device.
5. Transition is measured 200 mV from steady–state voltage with load of Figure 1b.
6. This parameter is sampled and not 100% tested.
7. Device is continuously selected (E = VIL, G = VIL).
8. Addresses valid prior to or coincident with E going low.
TIMING LIMITS
+5 V
480 Ω
OUTPUT
Z0 = 50 Ω
RL = 50 Ω
OUTPUT
255 Ω
5 pF
VL = 1.5 V
(a)
(b)
The table of timing values shows either a
minimum or a maximum limit for each parameter. Input requirements are specified from
the external system point of view. Thus, address setup time is shown as a minimum
since the system must supply at least that
much time. On the other hand, responses
from the memory are specified from the device point of view. Thus, the access time is
shown as a maximum since the device never
provides data later than that time.
Figure 1. AC Test Loads
MOTOROLA FAST SRAM
MCM6706CR
3
READ CYCLE 1 (See Note 7)
tAVAV
A (ADDRESS)
tAXQX
Q (DATA OUT)
DATA VALID
PREVIOUS DATA VALID
tAVQV
READ CYCLE 2 (See Note 8)
tAVAV
A (ADDRESS)
tELQV
E (CHIP ENABLE)
tEHQZ
tELQX
G (OUTPUT ENABLE)
tGHQZ
tGLQV
tGLQX
Q (DATA OUT)
DATA VALID
tAVQV
MCM6706CR
4
MOTOROLA FAST SRAM
WRITE CYCLE 1 (W Controlled, See Notes 1 and 2)
MCM6706CR–5
MCM6706CR–5.5
Symbol
Min
Max
Min
Max
Unit
Notes
tAVAV
5
—
5.5
—
ns
3
Address Setup Time
tAVWL
0
—
0
—
ns
Address Valid to End of Write
tAVWH
6
—
6
—
ns
Write Pulse Width
tWLWH,
tWLEH
6
—
6
—
ns
Data Valid to End of Write
tDVWH
3.5
—
3
—
ns
Data Hold Time
tWHDX
0
—
0
—
ns
Write Low to Data High–Z
tWLQZ
—
3.5
—
3.5
ns
4, 5, 6
Write High to Output Active
tWHQX
3
—
3
—
ns
4, 5, 6
Write Recovery Time
tWHAX
0
—
0
—
ns
Parameter
Write Cycle Time
NOTES:
1. A write occurs during the overlap of E low and W low.
2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus
contention conditions during read and write cycles.
3. All write cycle timings are referenced from the last valid address to the first transitioning address.
4. Transition is measured 200 mV from steady–state voltage with load of Figure 1b.
5. Parameter is sampled and not 100% tested.
6. At any given voltage and temperature, tWLQZ max is < tWHQX min both for a given device and from device to device.
WRITE CYCLE 1
tAVAV
A (ADDRESS)
tAVWH
tWHAX
E (CHIP ENABLE)
tWLEH
tWLWH
W (WRITE ENABLE)
tAVWL
tDVWH
D (DATA IN)
tWHDX
DATA VALID
tWLQZ
Q (DATA OUT)
HIGH–Z
HIGH–Z
tWHQX
MOTOROLA FAST SRAM
MCM6706CR
5
WRITE CYCLE 2 (E Controlled, See Notes 1 and 2)
MCM6706CR–5
MCM6706CR–5.5
Symbol
Min
Max
Min
Max
Unit
Notes
tAVAV
5
—
5.5
—
ns
3
Address Setup Time
tAVEL
0
—
0
—
ns
Address Valid to End of Write
tAVEH
5
—
5.5
—
ns
Chip Enable to End of Write
tELWH,
tELEH
5
—
5.5
—
ns
Data Valid to End of Write
tDVEH
3
—
3
—
ns
Data Hold Time
tEHDX
0
—
0
—
ns
Write Recovery Time
tEHAX
0
—
0
—
ns
Parameter
Write Cycle Time
4,5
NOTES:
1. A write occurs during the overlap of E low and W low.
2. Product sensitivities to noise require proper grounding and decoupling of power supplies as well as minimization or elimination of bus
contention conditions during read and write cycles.
3. All write cycle timing is referenced from the last valid address to the first transitioning address.
4. If E goes low coincident with or after W goes low, the output will remain in a high impedance condition.
5. If E goes high coincident with or before W goes high, the output will remain in a high impedance condition.
WRITE CYCLE 2
tAVAV
A (ADDRESS)
tAVEH
tELEH
E (CHIP ENABLE)
tAVEL
tELWH
tEHAX
W (WRITE ENABLE)
tDVEH
D (DATA IN)
tEHDX
DATA VALID
HIGH–Z
Q (DATA OUT)
ORDERING INFORMATION
(Order by Full Part Number)
MCM 6706CR X
X
X
Motorola Memory Prefix
Shipping Method (R = Tape and Reel, Blank = Rails)
Part Number
Speed (5 = 5 ns, 5.5 = 5.5 ns)
Package (J = 300 mil SOJ)
Full Part Numbers — MCM6706CRJ5
MCM6706CRJ5.5
MCM6706CR
6
MCM6706CRJ5R
MCM6706CRJ5.5R
MOTOROLA FAST SRAM
PACKAGE DIMENSIONS
32–LEAD
300 MIL SOJ
CASE 857–02
F 32 PL
0.17(0.007)
32
17
1
M
D 32 PL
0.17(0.007)
P
0.17(0.007) S B
16
-AL
G
DETAIL Z
A
S
S
NOTE 5
S
A
S
-B-X-
K
S
NOTE 4
NOTE 3
E C
0.10 (0.004)
-T-
SEATING
PLANE
R
0.25 (0.010)
MOTOROLA FAST SRAM
S RADIUS
S
B
S
NOTE 5
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DATUM PLANE -X- LOCATED AT TOP OF MOLD
PARTING LINE AND COINCIDENT WITH TOP OF
LEAD, WHERE LEAD EXITS BODY.
4. TO BE DETERMINED AT PLANE -X-.
5. TO BE DETERMINED AT PLANE -T-.
6. DIMENSION A & B DO NOT INCLUDE MOLD
PROTRUSION. MOLD PROTRUSION SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
7. 857-01 IS OBSOLETE, NEW STANDARD 857-02.
DIM
A
B
C
D
E
F
G
K
L
N
P
R
S
MILLIMETERS
MIN
MAX
20.83 21.08
7.50
7.74
3.26
3.75
0.41
0.50
2.24
2.48
0.67
0.81
1.27 BSC
0.89
1.14
0.64 BSC
0.76
1.14
8.38
8.64
6.60
6.86
0.77
1.01
INCHES
MIN
MAX
0.820 0.830
0.295 0.305
0.128 0.148
0.016 0.020
0.088 0.098
0.026 0.032
0.050 BSC
0.035 0.045
0.025 BSC
0.030 0.045
0.330 0.340
0.260 0.270
0.030 0.040
MCM6706CR
7
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MCM6706CR
8
◊
*MCM6706CR/D*
MOTOROLA MCM6706CR/D
FAST SRAM
Similar pages