MOTOROLA MCM6929AWJ8R 256k x 4 bit fast static random access memory Datasheet

MOTOROLA
Order this document
by MCM6929A/D
SEMICONDUCTOR TECHNICAL DATA
MCM6929A
Advance Information
256K x 4 Bit Fast Static Random
Access Memory
The MCM6929A is a 1,048,576 bit static random access memory organized
as 262,144 words of 4 bits. Static design eliminates the need for external clocks
or timing strobes.
Output enable (G) is a special control feature that provides increased system
flexibility and eliminates bus contention problems.
This device meets JEDEC standards for functionality and revolutionary pinout,
and is available in a 400 mil plastic small–outline J–leaded package.
•
•
•
•
•
•
•
Single 3.3 V Power Supply
Fully Static — No Clock or Timing Strobes Necessary
All Inputs and Outputs Are TTL Compatible
Three State Outputs
Fast Access Times: 8, 10, 12, 15 ns
Center Power and I/O Pins for Reduced Noise
Fully 3.3 V BiCMOS
BLOCK DIAGRAM
A
VDD
VSS
A
A
A
A
MEMORY
MATRIX
512 ROWS x 512 x 4
COLUMNS
ROW
DECODER
A
WJ PACKAGE
400 MIL SOJ
CASE 857A–02
PIN ASSIGNMENT
NC
1
32
A
A
2
31
A
A
3
30
A
A
4
29
A
A
5
28
A
E
6
27
G
DQ
7
26
DQ
VDD
8
25
VSS
VSS
9
24
VDD
DQ
10
23
DQ
W
11
22
A
A
12
21
A
A
13
20
A
A
14
19
A
A
15
18
A
NC
16
17
NC
A
A
PIN NAMES
A
DQ
COLUMN I/O
COLUMN DECODER
INPUT
DATA
CONTROL
DQ
A
A
A
A
A
A
A
A
A
A . . . . . . . . . . . . . . . . . . . . . Address Input
E . . . . . . . . . . . . . . . . . . . . . . Chip Enable
W . . . . . . . . . . . . . . . . . . . . Write Enable
G . . . . . . . . . . . . . . . . . . . Output Enable
DQ . . . . . . . . . . . . . . . Data Input/Output
VDD . . . . . . . . . . . + 3.3 V Power Supply
VSS . . . . . . . . . . . . . . . . . . . . . . . Ground
NC . . . . . . . . . . . . . . . . . . No Connection
E
W
G
This document contains information on a new product. Motorola reserves the right to change or discontinue this product without notice.
REV1
2/26/97
 Motorola, Inc. 1997
MOTOROLA
FAST SRAM
MCM6929A
1
TRUTH TABLE (X = Don’t Care)
E
G
W
Mode
VDD Current
Output
Cycle
H
X
X
Not Selected
ISB1, ISB2
High–Z
—
L
H
H
Output Disabled
IDDA
High–Z
—
L
L
H
Read
IDDA
Dout
Read Cycle
L
X
L
Write
IDDA
High–Z
Write Cycle
ABSOLUTE MAXIMUM RATINGS (See Note)
Symbol
Value
Unit
VDD
– 0.5 to + 4.6
V
Vin, Vout
– 0.5 to VDD + 0.5
V
Output Current
Iout
± 30
mA
Power Dissipation
PD
0.6
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Tstg
– 55 to + 125
°C
Rating
Power Supply Voltage
Voltage Relative to VSS for Any Pin Except
VDD
Storage Temperature — Plastic
This device contains circuitry to protect the
inputs against damage due to high static voltages or electric fields; however, it is advised
that normal precautions be taken to avoid application of any voltage higher than maximum
rated voltages to these high–impedance circuits.
This BiCMOS memory circuit has been designed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear feet
per minute is maintained.
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VDD = 3.3 V +10%, – 5% TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Symbol
Min
Typ
Max
Unit
Supply Voltage (Operating Voltage Range)
Parameter
VDD
3.135
3.3
3.6
V
Input High Voltage
VIH
2.2
—
VDD + 0.3**
V
Input Low Voltage
VIL
– 0.5*
—
0.8
V
Symbol
Min
Max
Unit
Input Leakage Current (All Inputs, Vin = 0 to VDD)
Ilkg(I)
—
± 1.0
µA
Output Leakage Current (E = VIH, Vout = 0 to VDD)
* VIL (min) = –0.5 V dc; VIL (min) = –2.0 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
** VIH (max) = VDD + 0.3 V dc; VIH (max) = VDD + 2 V ac (pulse width ≤ 2.0 ns) for I ≤ 20.0 mA.
DC CHARACTERISTICS
Parameter
Ilkg(O)
—
± 1.0
µA
Output Low Voltage (IOL = + 8.0 mA)
VOL
—
0.4
V
Output High Voltage (IOH = – 4.0 mA)
VOH
2.4
—
V
MCM6929A
2
MOTOROLA FAST SRAM
POWER SUPPLY CURRENTS (See Note 1)
6929A–8
Parameter
6929A–10
6929A–12
6929A–15
Symbol
Typ
Max
Typ
Max
Typ
Max
Typ
Max
Unit
Notes
AC Active Supply Current
(Iout = 0 mA) (VDD = max, f = fmax)
IDDA
—
150
—
130
—
120
—
110
mA
2, 3, 4
Active Quiescent Current
(E = VIL, VDD = max, f = 0 MHz)
IDD2
—
80
—
80
—
80
—
80
mA
AC Standby Current
(E = VIH, VDD = max, f = fmax)
ISB1
—
50
—
45
—
40
—
35
mA
2, 3, 4
CMOS Standby Current
ISB2
—
20
—
20
—
20
—
20
mA
(VDD = max, f = 0 MHz,
E ≥ VDD – 0.2 V,
Vin ≤ VSS + 0.2 V, or ≥ VDD – 0.2 V)
NOTES:
1. Typical current = 25°C @ 3.3 V.
2. Reference AC Operating Conditions and Characteristics for input and timing (VIH/VIL, tr/tf, pulse level 0 to 3.0 V, VIH = 3.0 V).
3. All addresses transition simultaneously low (LSB) and then high (MSB).
4. Data states are all zero.
CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested)
Symbol
Typ
Max
Unit
Address Input Capacitance
Cin
—
6
pF
Control Pin Input Capacitance
Cin
—
6
pF
Input/Output Capacitance
CI/O
—
8
pF
Parameter
MOTOROLA FAST SRAM
MCM6929A
3
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VDD = 3.3 V + 10%, – 5%, TA = 0 to +70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ns
Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1
READ CYCLE TIMING (See Notes 1 and 2)
6929A–8
Parameter
6929A–10
6929A–12
6929A–15
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Notes
Read Cycle Time
tAVAV
8
—
10
—
12
—
15
—
ns
3
Address Access Time
tAVQV
—
8
—
10
—
12
—
15
ns
Enable Access Time
tELQV
—
8
—
10
—
12
—
15
ns
Output Enable Access Time
tGLQV
—
4
—
5
—
6
—
7
ns
Output Hold from Address Change
tAXQX
3
—
3
—
3
—
3
—
ns
Enable Low to Output Active
tELQX
3
—
3
—
3
—
3
—
ns
4,5,6
Output Enable Low to Output Active
tGLQX
0
—
0
—
0
—
0
—
ns
4,5,6
Enable High to Output High–Z
tEHQZ
—
4
—
5
—
6
—
7
ns
4,5,6
Output Enable High to Output High–Z
tGHQZ
—
4
—
5
—
6
—
7
ns
4,5,6
NOTES:
1. W is high for read cycle.
2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles.
3. All read cycle timings are referenced from the last valid address to the first transitioning address.
4. At any given voltage and temperature, tEHQZ max < tELQX min, and tGHQZ max < tGLQX min, both for a given device and from
device to device.
5. Transition is measured 200 mV from steady–state voltage.
6. This parameter is sampled and not 100% tested.
7. Device is continuously selected (E = VIL, G = VIL).
8. Addresses valid prior to or coincident with E going low.
TIMING LIMITS
RL = 50 Ω
OUTPUT
Z0 = 50 Ω
VL = 1.5 V
The table of timing values shows either a minimum
or a maximum limit for each parameter. Input requirements are specified from the external system point of
view. Thus, address setup time is shown as a minimum since the system must supply at least that much
time. On the other hand, responses from the memory
are specified from the device point of view. Thus, the
access time is shown as a maximum since the device
never provides data later than that time.
Figure 1. AC Test Load
MCM6929A
4
MOTOROLA FAST SRAM
READ CYCLE 1 (See Note 7)
tAVAV
A (ADDRESS)
tAXQX
Q (DATA OUT)
PREVIOUS DATA VALID
DATA VALID
tAVQV
READ CYCLE 2 (See Note 8)
tAVAV
A (ADDRESS)
tAVQV
tELQV
E (CHIP ENABLE)
tEHQZ
tELQX
G (OUTPUT ENABLE)
tGHQZ
tGLQV
tGLQX
Q (DATA OUT)
MOTOROLA FAST SRAM
DATA VALID
MCM6929A
5
WRITE CYCLE 1 (W Controlled, See Notes 1 and 2)
6929A–8
Parameter
6929A–10
6929A–12
6929A–15
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Notes
tAVAV
8
—
10
—
12
—
15
—
ns
3
Address Setup Time
tAVWL
0
—
0
—
0
—
0
—
ns
Address Valid to End of Write
tAVWH
8
—
9
—
10
—
12
—
ns
Address Valid to End of Write, G High
tAVWH
7
—
8
—
9
—
10
—
ns
Write Pulse Width
tWLWH,
tWLEH
8
—
9
—
10
—
12
—
ns
Write Pulse Width, G High
tWLWH,
tWLEH
7
—
8
—
9
—
10
—
ns
Data Valid to End of Write
tDVWH
4
—
5
—
6
—
7
—
ns
Data Hold Time
tWHDX
0
—
0
—
0
—
0
—
ns
Write Low to Data High–Z
tWLQZ
—
4
—
5
—
6
—
7
ns
4,5,6
Write High to Output Active
tWHQX
3
—
3
—
3
—
3
—
ns
4,5,6
Write Recovery Time
tWHAX
0
—
0
—
0
—
0
—
ns
Write Cycle Time
NOTES:
1. A write occurs during the overlap of E low and W low.
2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles.
3. All write cycle timings are referenced from the last valid address to the first transitioning address.
4. Transition is measured 200 mV from steady–state voltage.
5. This parameter is sampled and not 100% tested.
6. At any given voltage and temperature, tWLQZ max < tWHQX min both for a given device and from device to device.
WRITE CYCLE 1
tAVAV
A (ADDRESS)
tAVWH
tWHAX
E (CHIP ENABLE)
tWLEH
tWLWH
W (WRITE ENABLE)
tDVWH
tAVWL
D (DATA IN)
tWHDX
DATA VALID
tWLQZ
Q (DATA OUT)
HIGH–Z
HIGH–Z
tWHQX
MCM6929A
6
MOTOROLA FAST SRAM
WRITE CYCLE 2 (E Controlled, See Notes 1 and 2)
6929A–8
Parameter
6929A–10
6929A–12
6929A–15
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Notes
tAVAV
8
—
10
—
12
—
15
—
ns
3
Address Setup Time
tAVEL
0
—
0
—
0
—
0
—
ns
Address Valid to End of Write
tAVEH
7
—
8
—
9
—
10
—
ns
Enable to End of Write
tELEH,
tELWH
7
—
8
—
9
—
10
—
ns
Data Valid to End of Write
tDVEH
4
—
5
—
6
—
7
—
ns
Data Hold Time
tEHDX
0
—
0
—
0
—
0
—
ns
Write Recovery Time
tEHAX
0
—
0
—
0
—
0
—
ns
Write Cycle Time
4,5
NOTES:
1. A write occurs during the overlap of E low and W low.
2. For common I/O applications, minimization or elimination of bus contention conditions is necessary during read and write cycles.
3. All write cycle timings are referenced from the last valid address to the first transitioning address.
4. If E goes low coincident with or after W goes low, the output will remain in a high impedance condition.
5. If E goes high coincident with or before W goes high, the output will remain in a high impedance condition.
WRITE CYCLE 2
tAVAV
A (ADDRESS)
tAVEH
tELEH
E (CHIP ENABLE)
tAVEL
tELWH
tEHAX
W (WRITE ENABLE)
tDVEH
D (DATA IN)
Q (DATA OUT)
MOTOROLA FAST SRAM
tEHDX
DATA VALID
HIGH–Z
MCM6929A
7
PACKAGE DIMENSIONS
32–LEAD
400 MIL SOJ
CASE 857A–02
F 32 PL
0.17 (0.007)
T B
S
S
A
S
N
32
D 32 PL
0.17 (0.007) S
17
1
T B
A
S
S
NOTE 3
DETAIL Z
16
0.17 (0.007)
-A-
T A
S
S
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TO BE DETERMINED AT PLANE -T-.
4. DIMENSION A & B DO NOT INCLUDE MOLD
PROTRUSION. MOLD PROTRUSION SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
5. DIMENSION A & B INCLUDE MOLD MISMATCH AND
ARE DETERMINED AT THE PARTING LINE.
S
P
L
G
-BE
C
0.10 (0.004)
K
DETAIL Z
-T-
SEATING
PLANE
S RADIUS
R
0.25 (0.010)
S
T A
S
B
S
NOTE 3
DIM
A
B
C
D
E
F
G
K
L
N
P
R
S
INCHES
MIN
MAX
0.820
0.830
0.395
0.405
0.128
0.148
0.016
0.020
0.088
0.098
0.026
0.032
0.050 BSC
0.035
0.045
0.025 BSC
0.030
0.045
0.435
0.445
0.365
0.375
0.030
0.040
MILLIMETERS
MIN
MAX
20.83 21.08
10.03 10.29
3.75
3.26
0.50
0.41
2.48
2.24
0.81
0.67
1.27 BSC
1.14
0.89
0.64 BSC
1.14
0.76
11.05 11.30
9.52
9.27
1.01
0.77
ORDERING INFORMATION
(Order by Full Part Number)
MCM 6929A WJ
XX
X
Motorola Memory Prefix
Shipping Method (R = Tape and Reel, Blank = Rails)
Part Number
Speed (8 = 8 ns, 10 = 10 ns, 12 = 12 ns, 15 = 15 ns)
Package (WJ = 400 mil SOJ)
Full Part Numbers — MCM6929AWJ8
MCM6929AWJ8R
MCM6929AWJ10
MCM6929AWJ10R
MCM6929AWJ12
MCM6929AWJ12R
MCM6929AWJ15
MCM6929AWJ15R
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Mfax: [email protected] – TOUCHTONE 602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
INTERNET: http://motorola.com/sps
MCM6929A
8
◊
MCM6929A/D
MOTOROLA FAST
SRAM
Similar pages