Intersil MD82C84A Cmos clock generator driver Datasheet

82C84A
CMOS Clock Generator Driver
March 1997
Features
Description
• Generates the System Clock For CMOS or NMOS
Microprocessors
The Intersil 82C84A is a high performance CMOS Clock Generatordriver which is designed to service the requirements of both CMOS
and NMOS microprocessors such as the 80C86, 80C88, 8086 and
the 8088. The chip contains a crystal controlled oscillator, a divide-bythree counter and complete “Ready” synchronization and reset logic.
• Up to 25MHz Operation
• Uses a Parallel Mode Crystal Circuit or External
Frequency Source
Static CMOS circuit design permits operation with an external frequency source from DC to 25MHz. Crystal controlled operation to
25MHz is guaranteed with the use of a parallel, fundamental mode
crystal and two small load capacitors.
• Provides Ready Synchronization
• Generates System Reset Output From Schmitt Trigger
Input
• TTL Compatible Inputs/Outputs
All inputs (except X1 and RES) are TTL compatible over temperature and voltage ranges.
Power consumption is a fraction of that of the equivalent bipolar circuits. This speed-power characteristic of CMOS permits the
designer to custom tailor his system design with respect to power
and/or speed requirements.
• Very Low Power Consumption
• Single 5V Power Supply
Ordering Information
• Operating Temperature Ranges
- C82C84A . . . . . . . . . . . . . . . . . . . . . . . . .0oC to +70oC
- I82C84A . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
- M82C84A . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
PART
NUMBER
TEMP. RANGE
PKG.
NO.
PACKAGE
CP82C84A
0oC to +70oC
IP82C84A
-40oC to +85oC
CS82C84A
0oC to +70oC
IS82C84A
-40oC to +85oC
CD82C84A
0oC to +70oC
ID82C84A
-40oC to +85oC
F18.3
MD82C84A/B
-55oC to +125oC
F18.3
18 Ld PDIP
E18.3
20 Ld PLCC
N20.35
E18.3
N20.35
18 Ld CERDIP F18.3
8406801VA
SMD#
MR82C84A/B
-55oC to +125oC
F18.3
20 Pad CLCC
84068012A
SMD#
J20.A
J20.A
Pinouts
AEN1
3
16
X2
RDY1
4
15
ASYNC
READY
5
14
EFI
RDY2
6
13
F/C
AEN2
7
12
OSC
CLK
8
11
RES
GND
9
10
RESET
2
1
20
19
RDY1
4
18
X2
READY
5
17
ASYNC
RDY2
6
16
EFI
AEN2
7
15
F/C
8
14
NC
NC
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
4-287
3
X1
X1
9
10
11
12
13
OSC
17
RES
2
CSYNC
PCLK
VCC
VCC
RESET
18
GND
1
CLK
CSYNC
PCLK
82C84A (PLCC, CLCC)
TOP VIEW
AEN1
82C84A (PDIP, CERDIP)
TOP VIEW
File Number
2974.1
82C84A
Functional Diagram
11
D
RES
X1
X2
F/C
EF1
CSYNC
RDY1
AEN1
RDY2
AEN2
ASYNC
16
Q
10
RESET
CK
17
XTAL
OSCILLATOR
12
OSC
13
÷3
SYNC
÷2
SYNC
2
PCLK
14
1
4
8
CLK
3
6
CK
D
Q
FF1
7
CK
5
D
Q
FF2
15
CONTROL PIN
LOGICAL 1
LOGICAL 0
F/C
External Clock
Crystal Drive
RES
Normal
Reset
RDY1, RDY2
Bus Ready
Bus Not Ready
AEN1, AEN2
Address Disabled
Address Enable
ASYNC
1 Stage Ready
Synchronization
2 Stage Ready
Synchronization
4-288
READY
82C84A
Pin Description
SYMBOL
NUMBER
TYPE
DESCRIPTION
AEN1,
AEN2
3, 7
I
ADDRESS ENABLE: AEN is an active LOW signal. AEN serves to qualify its respective Bus
Ready Signal (RDY1 or RDY2). AEN1 validates RDY1 while AEN2 validates RDY2. Two AEN
signal inputs are useful in system configurations which permit the processor to access two MultiMaster System Busses. In non-Multi-Master configurations, the AEN signal inputs are tied true
(LOW).
RDY1,
RDY2
4, 6
I
BUS READY (Transfer Complete). RDY is an active HIGH signal which is an indication from a
device located on the system data bus that data has been received, or is available RDY1 is qualified by AEN1 while RDY2 is qualified by AEN2.
ASYNC
15
I
READY SYNCHRONIZATION SELECT: ASYNC is an input which defines the synchronization
mode of the READY logic. When ASYNC is low, two stages of READY synchronization are provided. When ASYNC is left open or HIGH, a single stage of READY synchronization is provided.
READY
5
O
READY: READY is an active HIGH signal which is the synchronized RDY signal input. READY
is cleared after the guaranteed hold time to the processor has been met.
X1, X2
17, 16
IO
CRYSTAL IN: X1 and X2 are the pins to which a crystal is attached. The crystal frequency is 3
times the desired processor clock frequency, (Note 1).
F/C
13
I
FREQUENCY/CRYSTAL SELECT: F/C is a strapping option. When strapped LOW. F/C permits
the processor’s clock to be generated by the crystal. When F/C is strapped HIGH, CLK is generated for the EFI input, (Note 1).
EFI
14
I
EXTERNAL FREQUENCY IN: When F/C is strapped HIGH, CLK is generated from the input frequency appearing on this pin. The input signal is a square wave 3 times the frequency of the desired CLK output.
CLK
8
O
PROCESSOR CLOCK: CLK is the clock output used by the processor and all devices which directly connect to the processor’s local bus. CLK has an output frequency which is 1/3 of the crystal or EFI input frequency and a 1/3 duty cycle.
PCLK
2
O
PERIPHERAL CLOCK: PCLK is a peripheral clock signal whose output frequency is 1/2 that of
CLK and has a 50% duty cycle.
OSC
12
O
OSCILLATOR OUTPUT: OSC is the output of the internal oscillator circuitry. Its frequency is
equal to that of the crystal.
RES
11
I
RESET IN: RES is an active LOW signal which is used to generate RESET. The 82C84A provides a Schmitt trigger input so that an RC connection can be used to establish the power-up
reset of proper duration.
RESET
10
O
RESET: RESET is an active HIGH signal which is used to reset the 80C86 family processors. Its
timing characteristics are determined by RES.
CSYNC
1
I
CLOCK SYNCHRONIZATION: CSYNC is an active HIGH signal which allows multiple 82C84As
to be synchronized to provide clocks that are in phase. When CSYNC is HIGH the internal
counters are reset. When CSYNC goes LOW the internal counters are allowed to resume counting. CSYNC needs to be externally synchronized to EFI. When using the internal oscillator
CSYNC should be hardwired to ground.
GND
9
Ground
VCC
18
VCC: The +5V power supply pin. A 0.1µF capacitor between VCC and GND is recommended for
decoupling.
NOTE:
1. If the crystal inputs are not used X1 must be tied to VCC or GND and X2 should be left open.
4-289
82C84A
Functional Description
Clock Outputs
Oscillator
The oscillator circuit of the 82C84A is designed primarily for
use with an external parallel resonant, fundamental mode
crystal from which the basic operating frequency is derived.
The crystal frequency should be selected at three times the
required CPU clock. X1 and X2 are the two crystal input
crystal connections. For the most stable operation of the
oscillator (OSC) output circuit, two capacitors (C1 = C2) as
shown in the waveform figures are recommended. The output of the oscillator is buffered and brought out on OSC so
that other system timing signals can be derived from this stable, crystal-controlled source.
TABLE 1. CRYSTAL SPECIFICATIONS
PARAMETER
TYPICAL CRYSTAL SPEC
Frequency
2.4 - 25MHz, Fundamental, “AT” cut
Type of Operation
Parallel
Unwanted Modes
6dB (Minimum)
Load Capacitance
18 - 32pF
The CLK output is a 33% duty cycle clock driver designed to
drive the 80C86, 80C88 processors directly. PCLK is a peripheral clock signal whose output frequency is 1/2 that of CLK.
PCLK has a 50% duty cycle.
Reset Logic
The reset logic provides a Schmitt trigger input (RES) and a
synchronizing flip-flop to generate the reset timing. The reset
signal is synchronized to the falling edge of CLK. A simple RC
network can be used to provide power-on reset by utilizing this
function of the 82C84A.
READY Synchronization
Two READY input (RDY1, RDY2) are provided to accommodate two system busses. Each input has a qualifier (AEN1 and
AEN2, respectively). The AEN signals validate their respective
RDY signals. If a Multi-Master system is not being used the
AEN pin should be tied LOW.
Capacitors C1, C2 are chosen such that their combined
capacitance
Synchronization is required for all asynchronous active-going
edges of either RDY input to guarantee that the RDY setup
and hold times are met. Inactive-going edges of RDY in normally ready systems do not require synchronization but must
satisfy RDY setup and hold as a matter of proper system
design.
C1 x C2
CT = ---------------------- (Including stray capacitance)
C1 + C2
The ASYNC input defines two modes of READY synchronization operation.
matches the load capacitance as specified by the crystal
manufacturer. This ensures operation within the frequency
tolerance specified by the crystal manufacturer.
When ASYNC is LOW, two stages of synchronization are provided for active READY input signals. Positive-going asynchronous READY inputs will first be synchronized to flip-flop one of
the rising edge of CLK (requiring a setup time tR1VCH) and
the synchronized to flip-flop two at the next falling edge of
CLK, after which time the READY output will go active (HIGH).
Negative-going asynchronous READY inputs will be synchronized directly to flip-flop two at the falling edge of CLK, after
which the READY output will go inactive. This mode of operation is intended for use by asynchronous (normally not ready)
devices in the system which cannot be guaranteed by design
to meet the required RDY setup timing, TR1VCL, on each bus
cycle.
Clock Generator
The clock generator consists of a synchronous divide-bythree counter with a special clear input that inhibits the
counting. This clear input (CSYNC) allows the output clock
to be synchronized with an external event (such as another
82C84A clock). It is necessary to synchronize the CSYNC
input to the EFI clock external to the 82C84A. This is accomplished with two flip-flops. (See Figure 1). The counter output is a 33% duty cycle clock at one-third the input
frequency.
NOTE: The F/C input is a strapping pin that selects either the crystal
oscillator or the EFI input as the clock for the ÷ 3 counter. If
the EFI input is selected as the clock source, the oscillator
section can be used independently for another clock source.
Output is taken from OSC.
When ASYNC is high or left open, the first READY flip-flop is
bypassed in the READY synchronization logic. READY inputs
are synchronized by flip-flop two on the falling edge of CLK
before they are presented to the processor. This mode is available for synchronous devices that can be guaranteed to meet
the required RDY setup time.
ASYNC can be changed on every bus cycle to select the
appropriate mode of synchronization for each device in the
system.
EFI
CLOCK
SYNCHRONIZE
D
EFI
>
Q
82C84A
D
Q
CSYNC
>
(TO OTHER 82C84As)
NOTE: If EFI input is used, then crystal input X1 must be tied to VCC or GND and X2 should be left open. If the crystal inputs are used,
then EFI should be tied to VCC or GND.
FIGURE 1. CSYNC SYNCHRONIZATION
4-290
82C84A
Absolute Maximum Ratings
Thermal Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage . . . . . . . . . . . GND -0.5V to VCC +0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance . . . . . . . . . . . . . . . . θJA (oC/W) θJC (oC/W)
CERDIP Package . . . . . . . . . . . . . . . .
80
20
CLCC Package . . . . . . . . . . . . . . . . . .
95
28
PDIP Package . . . . . . . . . . . . . . . . . . .
85
N/A
PLCC Package . . . . . . . . . . . . . . . . . .
85
N/A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65oC to +150oC
Max Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
(PLCC - Lead Tips Only)
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range
C82C84A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
I82C84A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
M82C84A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
DC Electrical Specifications
SYMBOL
VCC = +5.0V ±10%,
TA = 0oC to +70oC (C82C84A),
TA = -40oC to +85oC (I82C84A),
TA = -55oC to +125oC (M82C84A)
PARAMETER
MIN
MAX
UNITS
VIH
Logical One Input Voltage
2.0
2.2
-
V
V
C82C84A, I82C84
M82C84A, Notes 1, 2
VIL
Logical Zero Input Voltage
-
0.8
V
Notes 1, 2, 3
VIHR
Reset Input High Voltage
VCC -0.8
-
V
VILR
Reset Input Low Voltage
-
0.5
V
Reset Input Hysteresis
0.2 VCC
-
-
VOH
Logical One Output Current
VCC -0.4
-
V
IOH = -4.0mA for CLK Output
IOH = -2.5mA for All Others
VOL
Logical Zero Output Voltage
-
0.4
V
IOL = +4.0mA for CLK Output
IOL = +2.5mA for All Others
-1.0
1.0
µA
VIN = VCC or GND except ASYNC,
X1: (Note 4)
-
40
mA
Crystal Frequency = 25MHz
Outputs Open, Note 5
VT+ - VT-
II
Input Leakage Current
ICCOP
Operating Power Supply Current
TEST CONDITIONS
NOTES:
1. F/C is a strap option and should be held either ≤ 0.8V or ≥ 2.2V. Does not apply to X1 or X2 pins.
2. Due to test equipment limitations related to noise, the actual tested value may differ from that specified, but the specified limit is
guaranteed.
3. CSYNC pin is tested with VIL ≤ 0.8V.
4. ASYNC pin includes an internal 17.5kΩ nominal pull-up resistor. For ASYNC input at GND, ASYNC input leakage current = 300µA
nominal, X1 - crystal feedback input.
5. f = 25MHz may be tested using the extrapolated value based on measurements taken at f = 2MHz and f = 10MHz.
Capacitance TA = +25oC
SYMBOL
CIN
COUT
PARAMETER
TYPICAL
UNITS
Input Capacitance
10
pF
Output Capacitance
15
pF
4-291
TEST CONDITIONS
FREQ = 1MHz, all measurements are
referenced to device GND
82C84A
AC Electrical Specifications
VCC = +5V± 10%,
TA = 0oC to +70oC (C82C84A),
TA = -40oC to +85oC (I82C84A),
TA = -55oC to +125oC (M82C84A)
LIMITS
SYMBOL
PARAMETER
MIN
MAX
UNITS
(NOTE 1)
TEST
CONDITIONS
TIMING REQUIREMENTS
(1)
TEHEL
External Frequency HIGH Time
13
-
ns
90%-90% VIN
(2)
TELEH
External Frequency LOW Time
13
-
ns
10%-10% VIN
(3)
TELEL
EFI Period
36
-
ns
XTAL Frequency
2.4
25
MHz
(4)
TR2VCL
RDY1, RDY2 Active Setup to CLK
35
-
ns
ASYNC = HIGH
(5)
TR1VCH
RDY1, RDY2 Active Setup to CLK
35
-
ns
ASYNC = LOW
(6)
TR1VCL
RDY1, RDY2 Inactive Setup to CLK
35
-
ns
(7)
TCLR1X
RDY1, RDY2 Hold to CLK
0
-
ns
(8)
TAYVCL
ASYNC Setup to CLK
50
-
ns
(9)
TCLAYX
ASYNC Hold to CLK
0
-
ns
(10)
TA1VR1V
AEN1, AEN2 Setup to RDY1, RDY2
15
-
ns
(11)
TCLA1X
AEN1, AEN2 Hold to CLK
0
-
ns
(12)
TYHEH
CSYNC Setup to EFI
20
-
ns
(13)
TEHYL
CSYNC Hold to EFI
(14)
TYHYL
CSYNC Width
(15)
TI1HCL
(16)
TCLI1H
Note 2
20
-
ns
2 TELEL
-
ns
RES Setup to CLK
65
-
ns
Note 3
RES Hold to CLK
20
-
ns
Note 3
125
-
ns
Note 6
TIMING RESPONSES
(17)
TCLCL
CLK Cycle Period
(18)
TCHCL
CLK HIGH Time
(1/3 TCLCL) +2.0
-
ns
Note 6
(19)
TCLCH
CLK LOW Time
(2/3 TCLCL) -15.0
-
ns
Note 6
(20)
(21)
TCH1CH2
TCL2CL1
CLK Rise or Fall Time
-
10
ns
1.0V to 3.0V
(22)
TPHPL
PCLK HIGH Time
TCLCL-20
-
ns
Note 6
(23)
TPLPH
PCLK LOW Time
TCLCL-20
-
ns
Note 6
(24)
TRYLCL
Ready Inactive to CLK (See Note 4)
(25)
TRYHCH
Ready Active to CLK (See Note 3)
(26)
TCLIL
(27)
(28)
-8
-
ns
Note 4
(2/3 TCLCL) -15.0
-
ns
Note 5
CLK to Reset Delay
-
40
ns
TCLPH
CLK to PCLK HIGH Delay
-
22
ns
TCLPL
CLK to PCLK LOW Delay
-
22
ns
(29)
TOLCH
OSC to CLK HIGH Delay
-5
22
ns
(30)
TOLCL
OSC to CLK LOW Delay
2
35
ns
NOTES:
1. Tested as follows: f = 2.4MHz, VIH = 2.6V, VIL = 0.4V, CL = 50pF, VOH ≥ 1.5V, VOL ≤ 1.5V, unless otherwise specified. RES and F/C must
switch between 0.4V and VCC -0.4V. Input rise and fall times driven at 1ns/V. VIL ≤ VIL (max) - 0.4V for CSYNC pin. VCC = 4.5V and 5.5V.
2. Tested using EFI or X1 input pin.
3. Setup and hold necessary only to guarantee recognition at next clock.
4. Applies only to T2 states.
5. Applies only to T3 TW states.
6. Tested with EFI input frequency = 4.2MHz.
4-292
82C84A
Timing Waveforms
NAME
EFI
I
OSC
O
CLK
(3)
I/O
tOLCH
(29)
O
(19)
tCLCH
(17) tCLCL
tCL2CL1
(21)
tCH1CH2
(20)
PCLK
CSYNC
O
(30)
tOLCL
tPLPH
(23)
tYHEH
(12)
(16)
tCLI1H
(22)
tPHPL
(15)
tI1HCL
(14)
tYHYL
RES
I
RESET
O
(26)
tCLIL
NOTE: All timing measurements are made at 1.5V, unless otherwise noted.
FIGURE 2. WAVEFORMS FOR CLOCKS AND RESETS SIGNALS
CLK
(7)
tCLR1X
tR1VCH
(5)
RDY1, 2
tR1VCL
(6)
(10)
tA1VR1V
tCLR1X
(7)
tCLA1X
(11)
AEN1, 2
tAYVCL
(8)
ASYNC
(9)
tCLAYX
READY
(25)
tRYHCH
(24) tRYLCL
FIGURE 3. WAVEFORMS FOR READY SIGNALS (FOR ASYNCHRONOUS DEVICES)
CLK
(7)
(4)
tCLR1X
tR1VCL
(6)
tR1VCL
RDY 1, 2
(10)
tA1VRIV
tCLR1X
(7)
AEN1, 2
(8)
tCLA1X
tAYVCL
(11)
ASYNC
tCLAYX
READY
(9)
(25)
tRYHCH
(24)
tRYLCL
FIGURE 4. WAVEFORMS FOR READY SIGNALS (FOR SYNCHRONOUS DEVICES)
4-293
(1)
tEHEL
tCHCL
(18)
tCLPL
(28)
tCLPH
(27)
(13)
tEHYL
I
(2)
tELEH
tELEL
82C84A
Test Load Circuits
2.25V
R = 740Ω FOR ALL OUTPUTS
EXCEPT CLK
463Ω FOR CLK OUTPUT
OUTPUT FROM
DEVICE UNDER TEST
CL
(SEE NOTE 3)
NOTES:
1. CL =100pF for CLK output.
2. CL = 50pF for all outputs except CLK.
3. CL = Includes probe and jig capacitance.
FIGURE 5. TEST LOAD MEASUREMENT CONDITIONS
PULSE
GENERATOR
LOAD
(SEE NOTE 1)
CLK
X1
C1
CLK
EF1
LOAD
(SEE NOTE 1)
VCC
X2
C2
F/C
F/C
CSYNC
CSYNC
FIGURE 6. TCHCL, TCLCH LOAD CIRCUITS
VCC
CLK
LOAD
(SEE NOTE 1)
READY
LOAD
(SEE NOTE 2)
AEN1
C1
X1
C2
CLK
LOAD
(SEE NOTE 1)
READY
LOAD
(SEE NOTE 2)
EF1
VCC
24MHz
PULSE
GENERATOR
TRIGGER
PULSE
GENERATOR
X2
F/C
AEN1
TRIGGER
PULSE
GENERATOR
RDY2
RDY2
AEN2
CSYNC
OSC
F/C
AEN2
CSYNC
FIGURE 7. TRYLCL, TRYHCH LOAD CIRCUITS
AC Testing Input, Output Waveform
OUTPUT
INPUT
VIH + 0.4V
VOH
1.5V
1.5V
VIL - 0.4V
VOL
NOTE: Input test signals must switch between VIL (maximum) -0.4V and VIH (minimum) +0.4V. RES and F/C must switch between 0.4V and
VCC -0.4V. Input rise and fall times driven at 1ns/V. VIL ≤ VIL (max) -0.4V for CSYNC pin. VCC -4.5V and 5.5V.
4-294
82C84A
Burn-In Circuits
MD82C84A CERDIP
VCC
C1
R1
F9
VCC
GND
R2
R2
1
18
2
17
3
16
R1
R2
F6
OPEN
R3
R1
F5
VCC
GND
F7
4
R2
15
F10
R1
5
R2
14
F1
R1
R1
6
13
7
12
R2
R1
F8
VCC
GND
F0
R1
R2
R2
R1
R2
8
11
9
10
R2
R2
F11
VCC
GND
F12
VCC
GND
MR82C84A CLCC
F0
R4
F9
20 19
18
5
17
6
16
7
15
14
8
NOTES:
VCC = 5.5V ±0.5V, GND = 0V.
VIH = 4.5V ±10%.
VIL = -0.2 to 0.4V.
R1 = 47kΩ, ±5%.
R2 = 10kΩ, ±5%.
R3 = 2.2kΩ, ±5%.
R4 = 1.2kΩ, ±5%.
C1 = 0.01µF (minimum).
F0 = 100kHz ±10%.
F1 = F0/2, F2 = F1/2, . . . F12 = F11/2.
4-295
F12
R4
10 11 12 13
VCC / 2
VCC / 2
R4
9
R4
OPEN
R4
C1
4
R4
F8
R4
1
VCC / 2
F7
R4
2
R4
F6
F5
VCC / 2
R4
R4
3
R4
VCC / 2
VCC
OPEN
R4
R4
R4
F10
F1
F11
OPEN
82C84A
Die Characteristics
DIE DIMENSIONS:
66.1 x 70.5 x 19 ± 1mils
GLASSIVATION:
Type: SiO2
Thickness: 8kÅ ± 1kÅ
METALLIZATION:
Type: Si - AI
Thickness: 11kÅ ± 1kÅ
WORST CASE CURRENT DENSITY:
1.42 x 105 A/cm2
Metallization Mask Layout
82C84A
AEN1
PCLK
CSYNC
VCC
X1
X2
RDY1
ASYNC
READY
RDY2
EFI
AEN2
F/C
CLK
GND
RESET
RES
OSC
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
4-296
ASIA
Intersil (Taiwan) Ltd.
Taiwan Limited
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
Similar pages