TI MDL-BDC24-B Stellarisâ® brushed dc motor control module with can (mdl-bdc24) Datasheet

Stellaris® Brushed DC Motor Control
Module with CAN (MDL-BDC24)
The Stellaris® Brushed DC Motor Control Module with
CAN (MDL-BDC24) improves on the highly successful
MDL-BDC design by providing variable speed control for
both 12 V and 24 V brushed DC motors at up to 40 A
continuous current, while adding a new RS232-based
serial control input that also functions as a serial-to-CAN
bridge. The MDL-BDC24 includes a rich set of sensor
interfaces, connectivity, and control options, including
analog and quadrature encoder interfaces, high
performance Controller Area Network (CAN) interfaces,
and an RS232 port. The module uses highly optimized
software and a powerful 32-bit Stellaris® microcontroller to
implement open-loop voltage control as well as
closed-loop control of speed, position, or motor current.
The H-bridge on the MDL-BDC24 is run at high-frequency
through the MCU's integrated PWM interface and enables
DC motors to run smoothly and quietly over a wide speed
range.
The MDL-BDC24 is powered by the ARM®
Cortex™-M3-based LM3S2616 microcontroller that
provides efficient and deterministic performance while
integrating CAN, UART, and advanced motion control
capabilities. TheMDL-BDC24 design also incorporates
several high-quality analog components from Texas
Instruments, including the SN65HVD1050 CAN
Transceiver, MAX3221 RS232 Line Driver/Receiver,
TPS54040 Swift DC/DC Converter, TPS73633 Voltage
Regulator, and INA193 Current Shunt Monitor. The
MDL-BDC24 is positioned into a wide variety of consumer
and industrial applications, including factory automation
devices and systems, mobile robots, household
appliances, pumping and ventilation systems, and electric
wheelchairs and mobility devices.
„
„
„
„
„
„
„
„
„
„
– Industry-standard R-C servo type (PWM) interface
– Controller Area Network (CAN) interface
– RS232 serial interface
Two options for closed-loop, speed, position, or current
control
– Controller Area Network (CAN) interface
– RS232 serial interface
CAN communication
– Full configurability of module options
– Real-time monitoring of current, voltage, speed, and
other parameters
– Load firmware over RS232/CAN
RS232 serial communication
– Bridges an RS232-enabled device to the CAN
– Directly interfaces to a PC serial port or National
Instruments cRIO
Limit switch inputs for forward and reverse directions
Firmware features
– Full configurability of closed-loop module parameters
– Real-time monitoring of sensor data including motor
current, encoder position or speed, and limit switch
state
Status LED indicates run, direction, and fault conditions
Motor brake/coast selector
Quadrature encoder input (QEI) and analog input
Color-coded screw terminals for all power wiring
Easy to customize using tools supporting the
MDL-BDC24 from Keil, IAR, Code Sourcery, or Code
Red (using a Stellaris evaluation kit or preferred
ARM® Cortex™-M3 debugger)
Features
For power wiring use
12AWG Wire with #6 ring
or spade terminals
Maintain 0.5" clearance
around all vents
Motor output is not protected
against short-circuits.
From Power
Distr ibution
Module
(–) In
Motor
Out
(–) Motor
(+) Motor
(+) In
Mounting holes
3.50" centers
User Switch
Maintain 0.5" clearance
around all vents
CAN Port
Status LED
RS232/CAN Port
Limit switch inputs
Use hooks to prevent
wires shaking loose
Encoder Input
Ordering Information
Product
Number
Description
Analog input(0-3V)
Motor coast/brake jumper
The MDL-BDC24 ships as a ready-to-run, yet
customizable, module with the following features:
„ Quiet control of brushed DC motors
– 15 kHz Hbridge frequency
„ Three options for open-loop voltage control
MDL-BDC24
MDL-BDC24-B
Stellaris® Brushed DC Motor Control Module
with CAN (MDL-BDC24) for Single-Unit
Packaging
Stellaris® Brushed DC Motor Control Module
with CAN (MDL-BDC24) for Volume Packaging
Texas Instruments • 108 Wild Basin, Suite 350 • Austin, TX 78746
Main: +1-512-279-8800 • Fax: +1-512-279-8879 • http://www.ti.com
Copyright © 2009–2011 Texas Instruments, Inc. All rights reserved. Stellaris and
StellarisWare are registered trademarks of Texas Instruments. ARM and Thumb are
registered trademarks, and Cortex is a trademark of ARM Limited. Other names and
brands may be claimed as the property of others.
PB-MDLBDC24-01
January 3, 2011
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages