Crane MHV2805DF Mhv single, dual and triple dc/dc converter Datasheet

Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
FEATURES
•
•
•
•
•
•
•
•
•
•
•
–55° to +125°C operation
16 to 50 VDC input
Fully Isolated
Optocoupler feedback
Fixed switching frequency
600 kHz typical,
Topology –
Dual Single Ended Flybacks
80 V / 120 ms transient protection
(12 Vout single and dual to 75 V,
15 Vout single and dual to 60V)
Inhibit and sync functions
Trim on single output models
Up to 81% efficiency
Low output noise
MODELS
VDC OUTPUT
SINGLE
DUAL
TRIPLE
3.3
±5
+5 & ±12
5
±12
+5 & ±15
12
±15
15
DESCRIPTION
Interpoint’s MHV Series™ of DC/DC converters offers a wide input
voltage range of 16 to 50 VDC and a choice of nine different output
voltage configurations comprised of single, dual or triple outputs.
The converters will withstand transients of up to 80 V for up to 120
milliseconds while maintaining output voltages (with the exception of
the 12 volt single and dual outputs which will withstand transients up
to 75 volts and the 15 volt single and dual outputs which will withstand up to 60 volts). The MHV Series operates at a full 15 watts of
output power (10 watts for the 3.3 volt single output) over the military temperature range of –55°C to +125°C while maintaining low
input and output noise.
CONVERTER DESIGN
MHV Series DC/DC converters are switching regulators that use
continuous flyback conversion topology with a clock frequency of
approximately 600 kHz. MHV Series converters incorporate two
internal converters with one converter phase shifted 180° from the
other to create a dual phase/phase-shifted operation. Each of the
internal converters operates at approximately one-half of the clock
frequency. This proprietary technology eliminates cross regulation,
minimizes input ripple, greatly reduces output ripple and improves
efficiency. On the triple output models, this design provides
completely independent regulation with no cross regulation effect
between the main and auxiliary outputs and no minimum loading
required on the main output.
INHIBIT FUNCTION
Open collector TTL levels control the inhibit circuit. The converter is
enabled when the inhibit terminal is left unconnected or when the
inhibit terminal is connected to a voltage between 11.5 and 50 V.
Crane Aerospace & Electronics
Electronics Group (Interpoint Brand)
PO Box 97005 • Redmond WA 98073-9705
425.882.3100 • [email protected]
www.craneae.com
When a low (0.8 V) is applied to the inhibit terminal the converter
shuts down, typically drawing 8.4 mA of input current. Inhibit
terminal resistance is 3.3 k ohms and draws 8.4 mA, typical.
SYNCHRONIZATION FUNCTION
Applying an external signal of 40% to 60% duty cycle and 500 to
700 kHz will synchronize the converter to your system requirements.
Free run clock frequency is approximately 600 kHz. If not used, the
sync terminal must be left unconnected.
TRIM
Single output converters feature a trim range of as low as 80% to
as high as 110% of Vout nominal, depending on the model. To trim
up, connect a resistor from output common (pin 4) to the trim
terminal (pin 3). To trim down, connect a resistor from the positive
output (pin 5) to the trim terminal (pin 3). See Figure 6 and trim
tables for more information.
UNDERVOLTAGE LOCKOUT
An undervoltage lockout of approximately 7 VDC keeps system
current levels low during startup.
SHORT CIRCUIT PROTECTION
Under short circuit conditions of 130% or more of full load current,
the converter will protect itself by shutting down. Short circuit duration should be brief because power dissipation may cause internal
temperatures to rise rapidly. Restart is automatic upon removal of
the short circuit.
Page 1 of 14
Rev D - 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
OPERATING CONDITIONS AND CHARACTERISTICS
MECHANICAL AND ENVIRONMENTAL
Input Voltage Range
• 16 to 50 VDC continuous
• Transient: see Electrical Characteristics tables
Output Power
• 15 watts (10 watts MHV283R3S)
Lead Soldering Temperature (10 sec per lead)
• 300°C
Storage Temperature Range (Case)
• –65°C to +150°C
Case Operating Temperature (Tc)
• –55°C to +125°C full power
• –55°C to +130°C absolute
Derating Output Power/Current
• Linearly from 100% at 125°C to 0% at 130°C
Output Voltage Temperature Coefficient
• 100 ppm/°C typical
Current Limit
• 130% of full load typical at 25°C
Isolation
• 100 megohm minimum at 500 V
Audio Rejection
• 30 dB typical
Conversion (Switching) Frequency
• Free run mode 300 kHz typical
245 kHz. min, 355 kHz. max
@ Tc = -55° to +125°C
Inhibit Pin Voltage (unit enabled)
• 11 V typical
Undervoltage Lockout
• 7 V input typical
Clock Frequency
• External sync range 490 to 710 kHz.
Positive
Input
Size (maximum)
Non-flanged Single and dual output models
2.125 x 1.125 x 0.400 inches (53.98 x 28.58 x 10.16 mm)
See case H2 for dimensions.
Triple output models
1.950 x 1.350 x 0.405 inches (49.53 x 34.29 x 10.29 mm)
See case F1 for dimensions.
Flanged Single and dual output models
2.910 x 1.125 x 0.400 inches (73.91 x 28.58 x 10.16 mm)
See case K3 for dimensions.
Triple output models
2.720 x 1.350 x 0.405 inches (69.09 x 34.29 x 10.29 mm)
See case J1 for dimensions.
Weight (maximum)
60 grams typical
Screening
Standard, ES, or 883 (Class H). See “883, Class H, QML
Products – Element Evaluation” and “883, Class H, QML
Products – Environmental Screening” for more information.
SYNC AND INHIBIT
0o
Positive
Output,
Main (+5)
PWM CM
Controller
Feedback Isolator
Output
Common
Positive
Output,
Auxiliary
Input
Common
Sync.
PWM CM
Controller
Feedback Isolator
Negative
Output,
Auxiliary
180o
FIGURE 1: MHV TRIPLE BLOCK DIAGRAM
www.craneae.com
Page 2 of 14
Rev D- 20060710
Sync In (490 to 710 kHz)
• Duty cycle 40% min, 60% max
• Logic low 0.8 V max
• Logic high 4.5 V min, 10 V max
• Referenced to input common
• If not used, leave unconnected
Sync Out - Referenced to input common
Inhibit (INH1, INH2) : TTL Open Collector
• Logic low (output disabled)
Logic low voltage ≤0.8 V
Inhibit pin current
8.4 mA typical, 10 mA maximum
• Referenced to input common
• Logic high (output enabled)
Open collector
Unconnected or 11.5 to 50 V
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
PINS NOT IN USE
PIN OUT
Pin
1
2
3
4
5
6,7
8
9
10
Single Output
Positive Input
Inhibit
Trim
Output Common
Positive Output
Case Ground
Case Ground
Sync In
Input Common
Dual Output
Positive Input
Inhibit
Positive Output
Output Common
Negative Output
Case Ground
Case Ground
Sync In
Input Common
Case
Inhibit (INH1, INH2)
Sync In
Triple Output
Positive Input
Main (+5) Output
Output Common
Neg. Aux. Output
Pos. Aux. Output
Case Ground
Inhibit
Sync In
Input Common
User’s discretion
Leave unconnected
Leave unconnected
Leave sync pin (pin 9) unconnected if not used.
Dot on top of cover
indicates pin one.
Dot on top of cover
indicates pin one.
1
1
2
3
4
2
3
4
5
5
BOTTOM VIEW
MHV TRIPLE
FLANGED AND NON-FLANGED
10
9
8
7
6
Dotted line outlines flanged package option.
10
9
8
7
Dotted line outlines flanged package option.
See cases H2 and K3 for dimensions.
See cases F1 and J1 for dimensions.
FIGURE 2: PIN OUT SINGLES AND DUALS
FIGURE 3: PIN OUT TRIPLE
www.craneae.com
Page 3 of 14
Rev D- 20060710
6
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
1
Positive Input
9
Sync In
2
Inhibit (pin 8 on triple
output models)
MHV
28V
10 Input Common
FIGURE 4: TYPICAL CONNECTIONS
1
Positive Output
Positive Input
2
1
Positive Input
FMC-461
MHV
or FMH-461
28V
EMI FILTER
5
Output Common 4
Input Common
3
10 Input Common
6, 7, 8
Case*
Chassis Ground
*The case ground connection should be as low an impedance as possible to minimize EMI.
Direct contact of baseplate to chassis ground provides the lowest impedance.
FIGURE 5: EMI FILTER CONNECTION
TRIM – SINGLE OUTPUT MODELS ONLY
Calculated Trim
Trim down: RT (kΩ) =
Trim up:
RT (kΩ) =
(
(
(Vo – 2.5)
Vo nominal – V0
2.5A
Vo – Vo nominal
Quick Reference Trim Table
)
)
–B
106 102
95
90
RTRIM ( (RT) k ohms
80
MHV283R3S
18
36
128
4
n/a
n/a
MHV2805S
8
20
81
23
5
n/a
MHV2812S
n/a
19
116
177
67
11
MHV2815S
0.3
21
122
255
104
28
RT
Values by Model
5V
12V 15V
3.7
14
18.2
10
30
30
3
MHV
SINGLE
OUTPUT
Notes
If calculated result is a negative value, the desired output voltage is outside the allowed trim range.
Calculated values of RT are ±15%.
When trimming up, do not exceed the maximum output power.
When trimming down, do not exceed the maximum output current.
www.craneae.com
110
A–B
Vo = desired output voltage
Formula
3.3V
A 3.7
B 10
% VOUT NOMINAL
MODEL
Page 4 of 14
Rev D- 20060710
TRIM
+VO
OUTPUT
COMMON
TRIM DOWN
5
4
TRIM UP
FIGURE 6: MHV SINGLE OUTPUTTRIM
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
SMD NUMBERS
MODEL NUMBERING KEY
MHV
28 512 T
F / 883
Base Model
Input Voltage
Output Voltage
(Main and aux. Vout for triple models)
(R = decimal point, 3R3 = 3.3 Vout)
Number of Outputs
(S = single, D = dual, T = triple)
Case Option
(Non-flanged case has no designator in
this position)
Screening
(Standard screening has no designator
in this position.)
STANDARD MICROCIRCUIT
DRAWING (SMD)
MHV SERIES
SIMILAR PART
5962-9852801HXC
5962-9852201HXC
5962-9852301HXC
5962-9852401HXC
5962-9852501HXC
5962-9852601HXC
5962-9852701HXC
5962-9673001HXC
5962-9673101HXC
MHV283R3S/883
MHV2805S/883
MHV2812S/883
MHV2815S/883
MHV2805D/883
MHV2812D/883
MHV2815D/883
MHV28512T/883
MHV28515T/883
Flanged SMD numbers for the MHV Series of converters have
the suffix HZC instead of HXC. For exact specifications for an
SMD product, refer to the SMD drawing available at
www.dscc.dla.mil/programs/smcr.
Model Selection
MHV28
Base model
Vout value
number of outputs
case option
screening
Choose one from each of the following rows
Vout value
for singles or duals: 3R3, 5, 12, or 15
for triples*: 512 or 515
“R” = decimal point, 3R3 = 3.3VDC
Number of outputs
S (single), D (dual) or T (triple)
Case option
non-flanged case option, leave blank
F (flanged case option),
Screening
standard screening, leave blank
/ES (ES screening), /883 (Class H, QML)
* for triple models “5” indicates the main voltage, “12” or“15” indicate the ± auxiliary voltages.
www.craneae.com
Page 5 of 14
Rev D- 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
SINGLE OUTPUT MODELS
PARAMETER
MHV283R3S
CONDITIONS
OUTPUT VOLTAGE
MHV2805S
MHV2812S
MHV2815S
MIN
TYP
MAX
MIN
TYP
MAX
MIN
TYP
MAX
3.27
3.30
3.33
4.95
5.00
5.05
11.88
12.00 12.12
MIN
TYP
MAX
UNITS
14.85 15.00
15.15
VDC
OUTPUT CURRENT
VIN = 16 to 50 VDC
0
—
3.03
0
—
3.0
0
—
1.25
0
—
1.0
A
OUTPUT POWER
VIN = 16 to 50 VDC
0
—
10
0
—
15
0
—
15
0
—
15
W
Tc = –55°C to +125°C
—
5
25
—
5
25
—
5
25
—
5
25
mV p-p
LINE REGULATION
VIN = 16 to 50 VDC
—
0
8
—
0
8
—
1
10
—
4
13
mV
LOAD REGULATION
NO LOAD TO FULL
—
15
30
—
15
40
—
8
30
—
10
35
mV
CONTINUOUS
16
28
50
16
28
50
16
28
50
16
28
50
VDC
OUTPUT RIPPLE
VOLTAGE
INPUT VOLTAGE
NO LOAD TO FULL1
INPUT CURRENT
INPUT RIPPLE
CURRENT
10 kHz - 2 MHz
TRANSIENT 120 ms
—
—
80
—
—
80
—
—
75
—
—
60
V
NO LOAD
—
34
42
—
44
52
—
43
55
—
45
62
mA
INHIBITED
—
8.4
10
—
8.4
10
—
8.4
10
—
8.4
10
mA
—
10
45
—
10
40
—
10
40
—
10
40
mA pp
69
72
—
74
77
—
79
81
—
78
81
—
%
10 kHz - 20 MHz
Tc = –55°C to +125°C
EFFICIENCY
LOAD FAULT2
POWER DISSIPATION
SHORT CIRCUIT2
—
—
7
—
—
8
—
—
7
—
—
7
W
RECOVERY1
—
—
20
—
—
20
—
—
20
—
—
20
ms
STEP LOAD
50% – 100% – 50%
RESPONSE3
TRANSIENT
—
—
300
—
—
300
—
—
350
—
—
450
mV pk
RECOVERY
—
—
1
—
—
1.5
—
—
1.3
—
—
1.3
mS
DELAY
—
14
18
—
14
18
—
14
18
—
14
18
ms
OVERSHOOT
—
0
100
—
0
100
—
0
120
—
0
150
mV pk
START-UP
0 TO 28 VIN
STEP LINE
RESPONSE1
CAPACITIVE LOAD1
16-50-16 VDC4
TRANSIENT
175
550
550
650
mVpk
RECOVERY4
0.9
2
2.5
2.5
mS
200
200
200
200
μF
Notes
1. Guaranteed by design, not tested.
2. Load fault is a short circuit (<50 mΩ). Recovery is into a resistive load.
3. Load step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
4. Input step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
www.craneae.com
Page 6 of 14
Rev D- 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
DUAL OUTPUT MODELS
PARAMETER
OUTPUT VOLTAGE
MHV2805D
MHV2812D
MHV2815D
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
MIN
TYP
MAX
+VOUT
4.95
5.00
5.05
11.88
12.00
12.12
14.85
15.00
15.15
–VOUT
4.95
5.00
5.05
11.88
12.00
12.12
14.85
15.00
15.15
UNITS
VDC
OUTPUT CURRENT
VIN = 16 TO 50 VDC
—
—
±1.50
—
—
±0.625
—
—
±0.500
A
OUTPUT POWER2
VIN = 16 TO 50 VDC
—
±7.5
15
—
±7.5
15
—
±7.5
15
W
—
5
35
—
5
25
—
10
50
mVp-p
—
0
10
—
0
10
—
0
10
mV
OUTPUT RIPPLE
VOLTAGE
10 kHz- 2 MHz
Tc = –55°C to +125°C
+VOUT / –VOUT
LINE REGULATION
VIN = 16 TO 50 VDC ±VOUT
LOAD REGULATION
NO LOAD TO FULL ±VOUT
INPUT VOLTAGE
NO LOAD TO FULL1
INPUT CURRENT
INPUT RIPPLE
CURRENT
—
5
15
—
2
15
—
2
15
mV
CONTINUOUS
16
28
50
16
28
50
16
28
50
VDC
TRANSIENT 120 msec
—
—
80
—
—
75
—
—
60
V
NO LOAD
—
22
30
—
32
43
—
37
50
mA
INHIBITED
—
8.4
10
—
8.4
10
—
8.4
10
10 kHz - 20 MHz
Tc = –55°C to +125°C
—
5
40
—
5
40
—
10
45
mA p-p
77
79
—
81
83
—
80
83
—
%
SHORT CIRCUIT
—
—
7.5
—
—
9
—
—
9
W
RECOVERY
—
—
20
—
—
25
—
—
30
ms
mV pk
EFFICIENCY
LOAD FAULT1,3
STEP LOAD
RESPONSE4 ± VOUT
START UP1
POWER DISSIPATION
50% – 100% — 50%
TRANSIENT
—
—
180
—
—
200
—
—
250
RECOVERY
—
—
1500
—
—
800
—
—
80
+VOUT DELAY
---
10
16
---
10
18
---
12
20
ms
---
0
50
---
0
100
---
0
100
mV pk
---
10
18
---
10
23
---
12
28
mS
TRANSIENT
---
---
400
---
---
500
---
---
500
mV pk
RECOVERY
---
---
4
---
---
3
---
---
3
mS
---
---
100
---
---
100
---
---
100
μF
±VOUT OVERSHOOT
-VOUT DELAY
STEP LINE1
RESPONSE1,5
CAPACITIVE LOAD1
16-50-16 VDC
Notes
1. Guaranteed by design, not tested.
2. Up to 7.5 watts is available from either output.
3. Load fault is a short circuit (<50 mΩ). Recovery is into a resistive load.
4. Load step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
5. Input step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
www.craneae.com
Page 7 of 14
Rev D- 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
TRIPLE OUTPUT MODELS
PARAMETER
OUTPUT VOLTAGE
OUTPUT CURRENT2
VIN = 16 TO 50
OUTPUT POWER3
VIN = 16 TO 50
LOAD REGULATION
CROSS REGULATION4
INPUT VOLTAGE1
INPUT CURRENT
MIN
MHV28515T
TYP
MAX
MIN
MAIN
4.95
5.0
5.05
4.95
5.0
5.05
+ AUXILIARY
– AUXILIARY
11.88
11.82
12.0
12.0
12.12
12.18
14.85
14.77
15.0
15.0
15.15
15.23
MAIN
+ AUXILIARY
0
—
—
0.208
2.0
0.333
0
—
—
0.167
2.0
0.267
– AUXILIARY
—
0.208
0.333
—
0.167
0.267
TOTAL
—
—
2.416
—
—
2.333
MAIN
+ AUXILIARY
—
—
—
—
10
4
—
—
—
—
10
4
– AUXILIARY
TOTAL
—
—
--—
4
15
—
—
_
—
4
15
—
—
8
9
22
22
—
—
8
9
22
22
MAIN
+AUXILIARY
—
—
0
5
5
35
—
—
0
7
5
35
– AUXILIARY
—
7
40
—
7
40
MAIN
+AUXILIARY
– AUXILIARY
—
—
—
10
10
40
20
30
70
—
—
—
10
10
40
20
30
80
—
16
—
400
28
—
800
50
80
—
16
—
400
28
—
800
50
80
OUTPUT RIPPLE
10 kHz to 2 MHz
VOLTAGE Tc= -55° to +125°C 10 kHz to 2 MHz
LINE REGULATION
VIN = MIN. TO MAX.
MHV28512T
TYP
MAX
CONDITION
MAIN
± AUXILIARY
- AUXILIARY CONDITION A & B
CONTINUOUS
TRANSIENT 120 ms
UNITS
VDC
A
W
mV p-p
mV
mV
mV
VDC
NO LOAD
—
30
37
—
34
41
INHIBITED
—
8.4
10
—
8.4
10
10 kHz to 10 MHz
—
10
30
—
10
30
mA p-p
76
—
78
—
—
9
75
—
78
—
—
9
%
MAIN
± AUXILIARY
RECOVERY - EACH OPUTPUT
MAIN
STEP LOAD RESPONSE6, 7 TRANSIENT
± AUXILIARY
RECOVERY
MAIN
± AUXILIARY
START-UP7
DELAY EACH OUTPUT
OVERSHOT
MAIN
± AUXILIARY
CAPACITIVE LOAD1
MAIN˜
± AUXILIARY
STEPLINE RESPONSE7
TRANSIENT1
MAIN
± AUXILIARY
MAIN
RECOVERY1
± AUXILIARY
—
--—
—
—
—
—
--------—
—
—
—
—
--—
—
—
—
7
--------—
—
—
—
9
25
250
550
2.5
3.5
15
100
240
200
100
400
500
3
4
—
--—
—
—
—
—
--------—
—
—
—
—
--—
—
—
—
7
--------—
—
—
—
9
25
250
550
2.5
3.5
15
100
300
200
100
400
500
3
4
mA
INPUT RIPPLE CURRENT
Tc= -55° to +125°C
EFFICIENCY
LOAD FAULT /
POWER DISSIPATION
SHORT CIRCUIT4
Notes
1. Guaranteed by design, not tested.
2. The sum of the 12 volt auxiliary output currents may not exceed 416 mA.
The sum of the 15 volt auxiliary output currents may not exceed 333 mA.
3. The sum of the auxiliary output power may not exceed 5 watts.
4. Cross regulation occurs between the two auxiliaries and is measured on –aux. +5 is held
constant at 2.0 A. Cross regulation is specified for two conditions:
www.craneae.com
W
mS
mV
ms
ms
mV pk
μF
mV pk
mS
A. Positive aux. = 2.5 W; -(50%) negative aux. = 2.5 W to 0.5 W (50% to 10%).
B. From +Po = 70% and -Po = 30% to + Po = 30% and -Po =70%.
Above conditions are referenced to 50%/50% balanced loads.
5. Load fault is a short circuit (<50 mΩ). Recovery is into a resistive load.
6. Load step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
7. Input step transition ≥ 10 μs. Recovery = time to settle to within 1% of Vout final value.
Page 8 of 14
Rev D- 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converter Cases
28 VOLT INPUT – 15 WATT
BOTTOM VIEW CASE F1
Platform
Dot on top of case indicates pin one
Seam Seal
1
2
3
4
5
10
9
8
7
6
0.970 (24.64)
1.370 (34.80)
0.040 dia.
(1.02)
0.570 (14.48)
1.170
(29.72)
0.170 (4.32)
1.350 max. (34.29)
0.170
(4.32)
1.770 (44.96)
Seal hole: 0.123 ±0.003 (3.12 ±0.08)
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
CAUTION
Heat from reflow or wave soldering may damage the device.
Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin.
Materials
Header
Cold Rolled Steel/Nickel/Gold
Cover
Kovar/Nickel
Pins
#52 alloy/Gold ceramic seal
Case F1, Rev C, 20051216
Please refer to the numerical dimensions for accuracy. All information is believed to be accurate,
but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make
changes in products or specifications without notice.
Copyright © 1999-2006 Interpoint Corp. All rights reserved.
FIGURE 7: CASE F1- MHV SINGLE AND DUAL
www.craneae.com
Page 9 of 14
Rev D - 20060710
1.950 max. (49.53)
0.000
0.25 (6.4)
0.000
0.405 max
(10.29)
0.000
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converter Cases
28 VOLT INPUT – 15 WATT
CASE H2
BOTTOM VIEW
Bathtub
Squared corner and dot on top
of case indicate pin one.
Seam Seal
1.110 max. (28.19)
1
2
3
4
5
10
9
8
7
6
1.045 (26.54)
1.445 (36.70)
1.845 (46.86)
0.040 dia
(1.02)
0.645 (16.38)
0.955 (24.26)
0.155 (3.94)
Seal hole: 0.092 ±0.002 (2.34 ±0.05)
Squared corner and dot on top
of case indicate pin one.
2.090 max. (53.01)
0.245 (6.22)
0.000
0.25 (6.4)
0.000
0.400 max.
(10.16)
0.000
1.110 (28.19)
1
2
3
4
5
10
9
8
7
6
0.645 (16.38)
1.045 (26.54)
1.445 (36.70)
1.845 (46.86)
0.955 (24.26)
0.155 (3.94)
CAUTION
Heat from reflow or wave soldering may damage the device.
Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin.
Materials
Header
Cold Rolled Steel/Nickel/Gold
Cover
Kovar/Nickel
Pins
#52 alloy/Gold compression glass seal
Case H2, Rev C - 20060109
Please refer to the numerical dimensions for accuracy. All information is believed to be accurate,
but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make
changes in products or specifications without notice.
Copyright © 1999-2006 Interpoint Corp. All rights reserved.
FIGURE 8: CASE H2 - MHV TRIPLE
www.craneae.com
Page 10 of 14
Rev D - 20060710
2.090 max. (53.01)
0.245 (6.22)
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
0.000
0.000
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converter Cases
28 VOLT INPUT – 15 WATT
BOTTOM VIEW CASE J1
Flanged cases: Designator "F" required in Case Option position of model number.
Bathtub
Dot on top of case indicates pin one
Seam Seal
1.350 max. (34.29)
1.170 (29.72)
1
0.040 dia.
(1.02)
2
3
4
5
0.162 dia
(4.11)
0.570 (14.48)
8
7
6
1.770 (44.96)
9
1.370 (34.80)
10
0.170 (4.32)
0.170
(4.32)
0.970 (24.64)
MHV Series Triple
0.670
(17.02)
2.720 max
(69.09)
Seal hole: 0.920 ±0.002
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
CAUTION
Heat from reflow or wave soldering may damage the device.
Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin.
Materials
Header Cold Rolled Steel/Nickel/Gold
Cover Kovar/Nickel
Pins
#52 alloy/Gold compression glass seal
Case J1, Rev D - 20060710
Please refer to the numerical dimensions for accuracy. All information is believed to be accurate,
but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make
changes in products or specifications without notice.
Copyright © 1999-2006 Interpoint Corp. All rights reserved.
FIGURE 9: CASE J1 - MHV TRIPLE
www.craneae.com
Page 11 of 14
Rev D - 20060710
2.720 max. (69.09)
Flange thickness: 0.060 (1.52)
2.150 (54.61)
0.000
0.210 (5.33)
0.25 (6.4)
0.000
0.405 max
(10.29)
0.000
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converter Cases
28 VOLT INPUT – 15 WATT
BOTTOM VIEW CASE K3
Flanged cases: Designator “F” required in Case Option position of model number.
Platform
Seam Seal
Dot on top of case indicates pin one
1.110 max. (28.19)
1
2
3
4
5
10
9
8
7
6
1.445
(36.70)
0.040 dia
(1.02)
1.045
(26.54)
0.955 (24.26)
0.162 dia
(4.11)
0.555 (14.1)
0.155 (3.94)
1.845
(46.86)
0.645
(16.38)
0.245
(6.22)
2.320
(58.93)
2.910 max.
(73.91)
Platform
0.000
0.230
(5.84)
0.25 ±0.03
(6.4 ±0.8)
0.000
0.400 max.
(10.16)
0.000
Dot on top of case indicates pin one
Seam Seal
1.110 max. (28.19)
1
2
3
4
5
10
9
8
7
6
0.645
(16.38)
1.045
(26.54)
1.445
(36.70)
0.040 dia
(1.02)
0.245
(6.22)
0.955 (24.26)
0.162 dia
(4.11)
0.555 (14.1)
0.155 (3.94)
Seal hole: 0.120 ±0.002 (3.05 ±0.05)
Case dimensions in inches (mm)
Tolerance ±0.005 (0.13) for three decimal places
±0.01 (0.3) for two decimal places
unless otherwise specified
2.910 max
(73.91)
CAUTION
Heat from reflow or wave soldering may damage the device.
Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin.
Materials
Header Cold Rolled Steel/Nickel/Gold
Cover Kovar/Nickel
Pins
#52 alloy/Gold compression glass seal
Case K3, Rev C, 20060110
FIGURE 11: CASE K3 - MHV SINGLE AND DUAL
www.craneae.com
Page 12 of 14
Rev D - 20060710
2.320
(58.93)
2.910 max.
(73.91)
Flange thickness: 0.060 (1.52)
1.845
(46.86)
0.000
– 0.230
(5.84)
0.25 ±0.03
(6.4 ±0.8)
0.000
0.400 max.
(10.16)
0.000
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
883, CLASS H, QML PRODUCTS – ELEMENT EVALUATION
ELEMENT EVALUATION
STANDARD
(NON-QML)1
M/S2
P3
TEST PERFORMED
(COMPONENT LEVEL)
CLASS H,
QML
2
M/S
P3
Element Electrical (probe)
yes
no
yes
yes
Element Visual
no
no
yes
yes
Internal Visual
no
no
yes
no
Final Electrical
no
no
yes
yes
Wire Bond Evaluation4
no
no
yes
yes
SLAM™/C-SAM:
Input Capacitors only
(Add’l test, not req. by H or K)
no
no
no
yes
Definitions:
Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534
SLAM™: Scanning Laser Acoustic Microscopy
C-SAM: C - Mode Scanning Acoustic Microscopy
Notes:
1. Non-QML products do no meet all of the requirements of MIL-PRF-38534
2. M/S = Active components (Microcircuit and Semiconductor Die)
3. P = Passive components
4. Not applicable to EMI filters that have no wire bonds
www.craneae.com
Page 13 of 14
Rev D- 20060710
Crane Aerospace & Electronics Power Solutions
MHV Single, Dual and Triple DC/DC Converters
28 VOLT INPUT – 15 WATT
883, CLASS H, QML PRODUCTS – ENVIRONMENTAL
SCREENING
TEST
125°C
STANDARD
non-QML
125°C
/ES
non-QML
Class H
/883
QML
Pre-cap Inspection
Method 2017, 2032
yes
yes
yes
Temperature Cycle (10 times)
Method 1010, Cond. C, -65°C to 150°C, ambient
Method 1010, Cond. B, -55°C to 125°C, ambient
no
no
no
yes
yes
no
Constant Acceleration
Method 2001, 3000 g
Method 2001, 500g
no
no
no
yes
yes
no
Burn-In
Method 1015, 160 hours at 125°C case, typical
96 hours at 125°C case, typical
no
no
no
yes
yes
no
Final Electrical Test MIL-PRF-38534, Group A
Subgroups 1 through 6: -55°C, +25°C, +125°C case
Subgroups 1 and 4: +25°C case
no
yes
no
yes
yes
no
Hermeticity Test
Fine Leak, Method 1014, Cond. A
Gross Leak, Method 1014, Cond. C
Gross Leak, Dip (1 x 10-3)
no
no
yes
yes
yes
no
yes
yes
no
Final Visual Inspection
Method 2009
yes
yes
yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534.
MHV Single, Dual and Triple. Rev D - 20060710. This revision supercedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. MHV Series is a trademark of
Interpoint. Copyright © 1994 - 2006 Interpoint Corporation. All rights reserved. www.craneae.com
Page 14 of 14
Similar pages