Melexis MLX90804 Programming kit Datasheet

MLXSPI-01
MLXSPI Programming kit
Features and Benefits
Compatible with nearly any pc running
windows 95, 98 or NT
Uses the standard parallel port
No additional supplies required
Easy to use software included
Supports all Melexis kitparts using the SPI
interface.
Applications
Lab and prototype use.
Used to program all Melexis devices
using the SPI interface
Ordering Information
Part No.
MLXSPI-01
Description
Melexis SPI Programmer unit including software
Accessories
Part No.
MLX90804 kitpart
MLX90805 kitpart
Description
Kitpart for the MLX90804 speed regulator for universal motors
Kitpart for the MLX90805 intelligent triac controller
1. Functional Diagram
2. Description
390129080401
Rev. 002
to pc parallel port
parallel interface to
pc
MLXSPI
interface
MLXSPI device
programmable
Vreg
The MLXSPI programmer is designed to have a
flexible and low cost programming tool for all
Melexis devices using the SPI interface.
The MLXSPI-01 programmer contains its own
programmable power supply which can be driven
by nearly all standard parallel ports on IBM
compatible PC’s.
The MLXSPI programmer needs to be controlled
with the accompanying software, running under
windows 95, windows 98 or windows NT. The PC
requires no custom configuration.
Page 1 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
TABLE OF CONTENTS
FEATURES AND BENEFITS........................................................................................................................ 1
APPLICATIONS ............................................................................................................................................ 1
1.
FUNCTIONAL DIAGRAM ......................................................................................................................1
2.
DESCRIPTION .......................................................................................................................................1
3.
GENERAL DESCRIPTION .................................................................................................................... 3
4.
COMMUNICATION ................................................................................................................................ 3
5.
INSTALLATION ..................................................................................................................................... 3
6.
HARDWARE DESCRIPTION ................................................................................................................ 3
7.
SOFTWARE DESCRIPTION ................................................................................................................. 3
8.
GENERAL INTERFACE ........................................................................................................................ 4
9.
PARAMETER DEFINITION INTERFACE..............................................................................................5
10. MLX90804 DEFINITION INTERFACE................................................................................................... 6
11. MLX90805 DEFINITION INTERFACE................................................................................................... 7
12. SPI FILE SYNTAX ................................................................................................................................. 8
390129080401
Rev. 002
Page 2 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
3. General Description
The MLXSPI-1 programmer was specifically
designed to program the Melexis family of kitparts
using the SPI interface.
The programmer is a combination of hardware
and software. The hardware needs to be
connected to the parallel port of a standard pc to
operate. There is no need for an additional
supply. It is advised that, when connecting the
programmer to a pc, no other hardware (like
printer, software key, …) is connected to the
same parallel port.
The hardware will generate the correct levels and
signals required for reading and writing to the
Melexis SPI devices.
The software will generate the timing for all
signals, but also gives a user-friendly interface to
define all parameters for all different Melexis SPI
kitparts. In this way the MLXSPI-01 is a tool
which helps to define the behavior of the
production device.
4. Communication
The MLXSPI uses a customized interface to be
connected to a parallel port of a pc.
Communication in both directions is done, and
also the power supply for the MLXSPI
programmer and the connected kitpart is taken
from the parallel port. It is therefore advised not
to connect any other hardware (like printer,
software key, …) to the same parallel port when
using the MLXSPI programmer.
5. Installation
The installation is very easy:
First connect the programmer box to your pc via
a standard parallel printer cable to a parallel port.
Copy the MLXSPI executable to your hard disk.
You need 1MB of free disk space.
MLXSPI hardware installation
computer
When running under Windows NT also copy the
file IOPORT.SYS to the
WINNT\SYSTEM32\DRIVERS directory.
This makes the installation complete.
6. Hardware description
The hardware consists of a box having:
1. A standard connector to connect to a parallel
port of a pc.
2. A zif socket to plug in the Melexis SPI device
to be programmed. The device must be
plugged in such that pin 1 of the chip is at the
side of the handle of the socket.
3. A led. When the box is connected to the pc,
the software is running and succeeded in
making connection with the box, this led is
blinking as long as the software is in idle
mode. While accessing the SPI kitpart (for
reading or writing) the led stops blinking and
is led continuously.
7. Software description
When starting the MLXSPI software an interface
window is activated on the screen. This interface
window consists of:
1. Title bar
The title bar indicates the program name and
has a system menu.
2. General interface
This part of the interface contains the
command buttons. Following commands are
available:
read SPI file
write SPI file
evaluate parameters
program parameters to kitpart
read parameters from kitpart
exit program
select parallel port
3. General interface
Parameter definition interface.
This part of the program interface is specific
to the different kitpart versions and therefore
consists of several pages, which can be
selected by clicking the tabs at the top side.
4. Status bar.
The status bar indicates the software version,
the source of the parameters that were
imported most recently, and the program
status.
MLXSPI
parallel interface cable
MLXSPI hardware
390129080401
Rev. 002
Page 3 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
MLXSPI interface
statusbar
general
interface
interface
specific to
kitpart
statusbar
8. General interface
The general interface contains the command
buttons. The execution of most of the commands
depends on the kitpart version that is selected in
the parameter definition interface. Following
commands are available:
1. Read SPI file:
This command will read all parameters of the
kitpart type as selected in the parameter
definition interface from the selected file. This
file must have been written previously with
the ‘write SPI file’ command. As the file is a
normal ascii file, it can also be edited
manually. The syntax of the SPI file is
explained at the end of this document.
The values as read from the file are directly
reflected in the parameter definition interface.
Parameters that are not present in the file are
not updated. The status bar indicates the file
name that has been read most recently.
2. Write SPI file:
This command will write all parameters, as
they are present in the parameter definition
interface to the selected file. If the file already
exists, the command will write into this file,
eventually overwriting the parameters stored
before in this file for the same kitpart. This
390129080401
Rev. 002
means that, if a file contains a set of
parameters for MLX90804 and for
MLX90805, only that part will be overwritten
that corresponds to the version in the
parameter definition interface.
The status bar indicates the file name that
has been written most recently.
3. Program:
This command will send the parameters as
defined in the parameter definition interface
to the MLXSPI programmer. This will be done
in several steps:
At first a consistency check is done on the
parameters. This check verifies that the set of
parameter values that is selected is possible
to program, or that the chosen combination
does not introduce an unpredictable behavior
of the kitpart. For more information see the
section describing the parameter definition
interface.
Then all parameters are read and
transformed to values to be programmed in
the kitpart. Most of the times this will
introduce rounding errors because not all
parameters can be programmed at the
resolution as present in the parameter
definition interface. For more information see
the section describing the parameter
definition interface.
Page 4 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
4.
5.
6.
7.
The calculated values are now sent to the
MLXSPI programmer to be written into the
kitpart.
At the end all parameters are read back from
the kitpart to verify the programming cycle.
Note that the system does not check whether
the correct version of the kitpart is plugged
into the MLXSPI programmer.
Read:
The read command will read the values back
from the kitpart, will recalculate and display
the corresponding parameters in the
parameter definition interface.
The status bar indicates that the displayed
parameters correspond to the kitpart.
Evaluate:
The evaluate command is very similar to the
combination of the program and read
command, but it skips the connection to the
MLXSPI programmer.
The command starts with a consistency
check, it transforms the parameters to
programming values and then recalculates
and redisplays the corresponding parameters
in the parameter definition interface.
The result corresponds exactly to the values
that should have been programmed and
shows the result of the rounding process.
Exit:
This command exits the program.
Select parallel port:
This command gives the software the
possibility to connect to parallel port LPT1 or
LPT2.
390129080401
Rev. 002
9. Parameter definition interface
This part of the program interface is specific to
the different kitpart versions and therefore
consists of several pages, which can be selected
by clicking the tabs at the top side.
In this interface the values of all parameters are
defined. It is therefore the interface where the
behavior of the programmed kitpart is created.
The following sections will explain how to use the
parameter definition interface for the different
types of kitparts. It will however not explain in
detail how to define the parameters to obtain a
certain behavior. For this the datasheets and
application notes corresponding to the production
version of the kitpart should be consulted.
Page 5 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
10. MLX90804 definition interface
This interface contains all parameters as are
described in application note MLX90804AN3
‘manual for definition of the options’. Use this
document as a guide to define all values.
Note that all speed settings are in RPM. The unit
for the minimum and maximum firing angle is
0.01*msec. This means that a value of 800
corresponds to 8 msec.
The parameter MAP is calculated and updated
automatically by the program.
During the consistency check a lot of verifications
are done. A few examples are:
1. Are the low speed limitation, the number of
poles and the SPD multiplier coefficient
consistent with the requirement as described in
MLX90804AN3?
2. Is the maximum speed limitation higher then
the speed settings on all potentiometer
settings?
During the transformation of the parameters to
programming values rounding errors can be
introduced. As an example, the maximum speed
limitation can only be programmed with a
resolution of 5 bits.
The box, indicating ‘chip version’, is used to
distinguish possible future versions of the kitpart.
The value can currently not be changed.
390129080401
Rev. 002
Page 6 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
11. MLX90805 definition interface
This interface contains all parameters as are
described in datasheet MLX90805 ‘intelligent triac
controller’. Use this document as a guide to define
all values.
Note that the unit for all delay settings is
0.01*msec. This means that a value of 800
corresponds to 8 msec.
The soft start duration is defined by a value
between 0 and 31, but the program automatically
calculates and displays the corresponding value in
msec.
During the consistency check a lot of verifications
are done. A few examples are:
1. Is the phase delay defined for each
potentiometer setting smaller then the
maximum delay time?
2. Is the phase delay defined for each
potentiometer setting smaller then half the
period of the line frequency?
During the transformation of the parameters to
programming values small rounding errors can be
introduced.
The box, indicating ‘chip version’, is used to
distinguish possible future versions of the kitpart.
The value can currently not be changed.
390129080401
Rev. 002
Page 7 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
12.
SPI file syntax
The syntax of the SPI file is very similar to the
syntax used in the initialization files used by the
operating systems.
The file can contain several groups, with each
group having a number of records. The groups
correspond to the kitpart type, and each record
contains a parameter. Following is a dump of an
SPI file containing the default values of all
parameters for both MLX90804 and 90805.
[90804]
P04Coil=True
P04FG10M=True
F0450=True
P04RETRIG=True
NumPoles=6
SLIMA[4:0]=20000
SLIM[9:0]=500
DUTS[1:0]=0
SSE[1:0]=3
PX[3:1]=6
SFT[4:0]=0
LD[9:0]=0
MAX[9:0]=0
MIN[9:0]=800
SPE[1:0]=0
UPR[4:0]=1
DWR[4:0]=1
MULT[7:0]=25
SpeedSetting[15]=16000
SpeedSetting[14]=15000
SpeedSetting[13]=14000
SpeedSetting[12]=13000
SpeedSetting[11]=12000
SpeedSetting[10]=11000
SpeedSetting[9]=10000
SpeedSetting[8]=9000
SpeedSetting[7]=8000
SpeedSetting[6]=7000
SpeedSetting[5]=6000
SpeedSetting[4]=5000
SpeedSetting[3]=4000
SpeedSetting[2]=3000
SpeedSetting[1]=2000
SpeedSetting[0]=1000
390129080401
Rev. 002
[90805]
F0550=True
P05RETRIG=True
DUTS[1:0]=2
ATN[4:0]=31
MINA[3:0]=13
MIN[9:0]=700
PhaseDelay[15]=122
PhaseDelay[14]=241
PhaseDelay[13]=283
PhaseDelay[12]=315
PhaseDelay[11]=345
PhaseDelay[10]=372
PhaseDelay[9]=397
PhaseDelay[8]=421
PhaseDelay[7]=444
PhaseDelay[6]=466
PhaseDelay[5]=487
PhaseDelay[4]=510
PhaseDelay[3]=532
PhaseDelay[2]=554
PhaseDelay[1]=577
PhaseDelay[0]=600
Page 8 of 9
User’s Guide
Mar/03
MLXSPI-01
MLXSPI Programming kit
For the latest version of this document, go to our website at:
www.melexis.com
Or for additional information contact Melexis Direct:
Europe and Japan:
All other locations:
Phone: +32 13 67 04 95
E-mail: [email protected]
Phone: +1 603 223 2362
E-mail: [email protected]
QS9000, VDA6.1 and ISO14001 Certified
390129080401
Rev. 002
Page 9 of 9
User’s Guide
Mar/03
Similar pages