Fairchild MM74HC4316M Quad analog switch with level translator Datasheet

Revised February 1999
MM74HC4316
Quad Analog Switch with Level Translator
General Description
and outputs and digital inputs are protected from electrostatic damage by diodes to VCC and ground.
The MM74HC4316 devices are digitally controlled analog
switches implemented in advanced silicon-gate CMOS
technology. These switches have low “ON” resistance and
low “OFF” leakages. They are bidirectional switches, thus
any analog input may be used as an output and vice-versa.
Three supply pins are provided on the MM74HC4316 to
implement a level translator which enables this circuit to
operate with 0–6V logic levels and up to ±6V analog switch
levels. The MM74HC4316 also has a common enable input
in addition to each switch's control which when LOW will
disable all switches to their OFF state. All analog inputs
Features
■ Typical switch enable time: 20 ns
■ Wide analog input voltage range: ±6V
■ Low “ON” resistance:
50 typ. (VCC−VEE = 4.5V) 30 typ. (VCC−VEE = 9V)
■ Low quiescent current: 80 µA maximum (74HC)
■ Matched switch characteristics
■ Individual switch controls plus a common enable
Ordering Code:
Order Number
Package Number
MM74HC4316M
MM74HC4316SJ
MM74HC4316MTC
MM74HC4316N
M16A
M16D
MTC16
N16E
Package Description
16-Lead Small Outline Integrated Package (SOIC), JEDEC MS-012, 0.150” Narrow
16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-1536, 4.4mm Wide
16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Logic Diagram
Connection Diagram
Pin Assignments for DIP, SOIC, SOP and TSSOP
Top View
Truth Table
Inputs
© 1999 Fairchild Semiconductor Corporation
Switch
En
CTL
H
X
“OFF”
L
L
“OFF”
L
H
“ON”
DS005369.prf
I/O–O/I
www.fairchildsemi.com
MM74HC4316 Quad Analog Switch with Level Translator
February 1984
MM74HC4316
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions
(Note 2)
−0.5 to +7.5V
Supply Voltage (VCC)
Min
Max
2
6
V
0
−6
V
0
VCC
V
−40
+85
°C
(tr, tf) VCC = 2.0V
1000
ns
VCC = 4.5V
500
ns
+0.5 to −7.5V Supply Voltage (V )
CC
−1.5 to VCC +1.5V Supply Voltage (V )
Supply Voltage (VEE)
DC Control Input Voltage (VIN)
EE
VEE−0.5 to VCC +0.5V DC Input or Output Voltage
±20 mA
)
(V , V
DC Switch I/O Voltage (VIO)
Clamp Diode Current (IIK, IOK)
IN
OUT
±25 mA Operating Temperature Range (T )
A
±50 mA Input Rise or Fall Times
DC Output Current, per pin (IOUT)
DC VCC or GND Current, per pin (ICC )
−65°C to +150°C
Storage Temperature Range (TSTG)
Power Dissipation (PD)
Units
(Note 3)
600 mW
VCC = 6.0V
400
ns
S.O. Package only
500 mW
VCC = 12.0V
250
ns
Lead Temperature (TL)
(Soldering 10 seconds)
Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur.
260°C
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temperature derating — plastic “N” package: −
12 mW/°C from 65°C to 85°C.
DC Electrical Characteristics
Symbol
VIH
VIL
Parameter
(Note 4)
Conditions
VEE
VCC
RON
IIN
TA = −40 to 85°C TA = −55 to 125°C
Units
Guaranteed Limits
Minimum HIGH Level
2.0V
1.5
1.5
1.5
V
Input Voltage
4.5V
3.15
3.15
3.15
V
6.0V
4.2
4.2
4.2
V
Maximum LOW Level
2.0V
0.5
0.5
0.5
V
4.5V
1.35
1.35
1.35
V
6.0V
1.8
1.8
1.8
V
Input Voltage
RON
TA = 25°C
Typ
Minimum “ON” Resistance
VCTL = VIH, IS = 2.0 mA
GND
4.5V
100
170
200
220
Ω
(Note 5)
VIS = V CC to VEE
−4.5V
4.5V
40
85
105
110
Ω
(Figure 1)
−6.0V
6.0V
30
70
85
90
Ω
GND
2.0V
100
180
215
240
Ω
VCTL = VIH, IS = 2.0 mA
GND
4.5V
40
80
100
120
Ω
VIS = V CC or VEE
−4.5V
4.5V
50
60
75
80
Ω
(Figure 1)
−6.0V
6.0V
20
40
60
70
Ω
Maximum “ON” Resistance
VCTL = VIH
GND
4.5V
10
15
20
20
Ω
Matching
VIS = V CC to VEE
−4.5V
4.5V
5
10
15
15
Ω
−6.0V
6.0V
5
10
15
15
Ω
GND
6.0V
±0.1
±1.0
±1.0
µA
Maximum Control
VIN = VCC or GND
Input Current
IIZ
Maximum Switch “OFF”
VOS = V CC or VEE
GND
6.0V
±60
±600
±600
nA
Leakage Current
VIS = V EE or VCC
−6.0V
6.0V
±100
±1000
±1000
nA
VCTL = VIL (Figure 2)
IIZ
Maximum Switch “ON”
VIS = V CC to VEE
GND
6.0V
±40
±150
±150
nA
Leakage Current
VCTL = VIH, VOS = OPEN −6.0V
6.0V
±60
±300
±300
nA
(Figure 3)
ICC
Maximum Quiescent
VIN = VCC or GND
GND
6.0V
2.0
20
40
µA
Supply Current
IOUT = 0 µA
−6.0V
6.0V
8.0
80
160
µA
Note 4: For a power supply of 5V ±10% the worst case on resistances (RON) occurs for HC at 4.5V. Thus the 4.5V values should be used when designing
with this supply. Worst case VIH and VIL occur at VCC=5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current occurs
for CMOS at the higher voltage and so the 5.5V values should be used.
Note 5: At supply voltages (VCC–VEE) approaching 2V the analog switch on resistance becomes extremely non-linear. Therefore it is recommended that
these devices be used to transmit digital only when using these supply voltages.
www.fairchildsemi.com
2
VCC = 2.0V−6.0V, VEE = 0V−6V, CL = 50 pF (unless otherwise specified)
Symbol
Parameter
Conditions
VEE
VCC
TA = +25°C
Typ
TA = −40°C to +85°C TA = −55°C to +125°C
Guaranteed Limits
Units
tPHL,
Maximum Propagation
GND 2.0V
25
50
63
75
ns
tPLH
Delay Switch
GND 4.5V
5
10
13
15
ns
In to Out
−4.5V 4.5V
4
8
12
14
ns
−6.0V 6.0V
3
7
11
13
ns
GND 2.0V
30
165
206
250
ns
RL = 1 kΩ
tPZL,
Maximum Switch
tPZH
Turn “ON” Delay
GND 4.5V
20
35
43
53
ns
(Control)
−4.5V 4.5V
15
32
39
48
ns
−6.0V 6.0V
14
30
37
45
ns
GND 2.0V
45
250
312
375
ns
RL = 1 kΩ
tPHZ,
Maximum Switch
tPLZ
Turn “OFF” Delay
GND 4.5V
25
50
63
75
ns
(Control)
−4.5V 4.5V
20
44
55
66
ns
−6.0V 6.0V
20
44
55
66
tPZL,
Maximum Switch
GND 2.0V
35
205
256
308
ns
tPZH
Turn “ON” Delay
GND 4.5V
20
41
52
62
ns
(Enable)
−4.5V 4.5V
19
38
48
57
ns
−6.0V 6.0V
18
36
45
54
ns
GND 2.0V
58
265
330
400
ns
tPLZ,
Maximum Switch
tPHZ
Turn “OFF” Delay
GND 4.5V
28
53
67
79
ns
(Enable)
−4.5V 4.5V
23
47
59
70
ns
21
47
59
70
−6.0V 6.0V
fMAX
Minimum Frequency
RL = 600Ω, VIS = 2VPP
Response (Figure 7)
at (VCC−VEE/2)
0V
4.5
−4.5V 4.5V
ns
40
MHz
100
MHz
20 log (VOS/VIS)= −3 dB (Note 6) (Note 7)
Control to Switch
RL = 600Ω, F = 1 MHz
Feedthrough Noise
CL = 50 pF
(Figure 8)
(Note 7) (Note 8)
Crosstalk Between
RL = 600Ω, F = 1 MHz
4.5V
100
mV
−4.5V 4.5V
250
mV
4.5V
−52
dB
−4.5V 4.5V
−50
dB
4.5V
−42
dB
−4.5V 4.5V
−44
dB
4.5V
0.013
%
VIS = 8VPP −4.5V 4.5V
0.008
%
5
pF
35
pF
0.5
pF
15
pF
any Two Switches
0V
(Figure 9)
Switch OFF Signal
THD
RL = 600Ω, F = 1 MHz
Feedthrough Isolation
VCTL = VIL,
(Figure 10)
(Note 7) (Note 8)
Sinewave Harmonic
RL = 10 KΩ, CL = 50 pF,
Distortion
F = 1 KHz
0V
VIS = 4VPP
(Figure 11)
CIN
0V
0V
Maximum Control
Input Capacitance
CIN
Maximum Switch
Input Capacitance
CIN
Maximum Feedthrough
VCTL = GND
Capacitance
CPD
Power Dissipation
Capacitance
Note 6: Adjust 0 dBm for F = 1 KHz (Null RL/Ron Attenuation).
Note 7: VIS is centered at VCC–VEE/2.
Note 8: Adjust for 0 dBm.
3
www.fairchildsemi.com
MM74HC4316
AC Electrical Characteristics
MM74HC4316
AC Test Circuits and Switching Time Waveforms
FIGURE 1. “ON” Resistance
FIGURE 2. “OFF” Channel Leakage Current
FIGURE 3. “ON” Channel Leakage Current
FIGURE 4. tPHL, tPLH Propagation Delay Time Signal Input to Signal Output
FIGURE 5. tPZL, tPLZ Propagation Delay Time Control to Signal Output
FIGURE 6. tPZH, tPHZ Propagation Delay Time Control to Signal Output
www.fairchildsemi.com
4
MM74HC4316
AC Test Circuits and Switching Time Waveforms
(Continued)
FIGURE 7. Frequency Response
FIGURE 8. Crosstalk: Control Input to Signal Output
FIGURE 9. : Crosstalk Between Any Two Switches
FIGURE 10. Switch OFF Signal Feedthrough Isolation
FIGURE 11. Sinewave Distortion
5
www.fairchildsemi.com
MM74HC4316
Typical Performance Characteristics
Typical “ON” Resistance
Typical Crosstalk Between
Any Two Switches
Typical Frequency Response
Special Considerations
the analog switch input pins, the voltage drop across the
switch must not exceed 0.6V (calculated from the ON resistance).
In certain applications the external load-resistor current
may include both VCC and signal line components. To
avoid drawing VCC current when switch current flows into
www.fairchildsemi.com
6
MM74HC4316
Physical Dimensions inches (millimeters) unless otherwise noted
16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150” Narrow
Package Number M16A
16-Lead small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M16D
7
www.fairchildsemi.com
MM74HC4316
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC16
www.fairchildsemi.com
8
16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Package Number N16E
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
1. Life support devices or systems are devices or systems
device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the
sonably expected to cause the failure of the life support
body, or (b) support or sustain life, and (c) whose failure
device or system, or to affect its safety or effectiveness.
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
www.fairchildsemi.com
user.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
MM74HC4316 Quad Analog Switch with Level Translator
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Similar pages