Freescale MMA6270QR2 ±1.5 g - 6 g dual axis low-g micromachined accelerometer Datasheet

Freescale Semiconductor
Technical Data
Document Number: MMA6270QT
Rev 1, 06/2007
±1.5 g - 6 g Dual Axis Low-g
Micromachined Accelerometer
The MMA6270QT low cost capacitive micromachined accelerometer
features signal conditioning, a 1-pole low pass filter, temperature compensation
and g-Select which allows for the selection among four sensitivities. Zero-g
offset full scale span and filter cut-off are factory set and require no external
devices. Includes a Sleep Mode that makes it ideal for handheld battery
powered electronics.
Features
MMA6270QT: XY AXIS
ACCELEROMETER
±1.5 g / 2 g / 4 g / 6 g
Selectable Sensitivity (1.5 g / 2 g / 4 g / 6 g)
Low Current Consumption: 500 µA
Sleep Mode: 3 µA
Low Voltage Operation: 2.2 V – 3.6 V
6 mm x 6 mm x 1.45 mm QFN
High Sensitivity (800 mV/g @1.5 g)
Fast Turn On Time
Integral Signal Conditioning with Low Pass Filter
Robust Design, High Shocks Survivability
Pb-Free Terminations
Environmentally Preferred Package
Low Cost
Bottom View
16-LEAD
QFN
CASE 1622-02
Typical Applications
Laptop PC: Freefall Detection, Anti-Theft
Cell Phone: Image Stability, Text Scroll, Motion Dialing, E-Compass
PDA: Text Scroll
Navigation and Dead Reckoning: E-Compass Tilt Compensation
Gaming: Tilt and Motion Sensing, Event Recorder
Robotics: Motion Sensing
Appliances: Vibration Sensing
16 15
MMA6270QT
– 40 to +105°C
1622-02
QFN-16, Tray
MMA6270QR2
– 40 to +105°C
1622-02
QFN-16,Tape & Reel
N/C
Sleep
Mode
g-Select1 1
12
g-Select2 2
11 N/C
VDD 3
10 N/C
VSS 4
9 N/C
5
6
7
8
N/C
Package
14 13
N/C
Package
Drawing
N/C
Device Name
Temperature
Range
YOUT
ORDERING INFORMATION
XOUT
Top View
N/C
•
•
•
•
•
•
•
N/C
•
•
•
•
•
•
•
•
•
•
•
•
MMA6270QT
Figure 1. Pin Connections
© Freescale Semiconductor, Inc., 2005-2007. All rights reserved.
VDD
g-Select1
g-Select2
G-Cell
Sensor
Sleep Mode
Oscillator
Clock
Generator
C to V
Converter
Gain
+
Filter
Control Logic
EEPROM Trim Circuits
X-Temp
Comp
XOUT
Y-Temp
Comp
YOUT
VSS
Figure 2. Simplified Accelerometer Functional Block Diagram
Table 1. Maximum Ratings
(Maximum ratings are the limits to which the device can be exposed without causing permanent damage.)
Rating
Symbol
Value
Unit
Maximum Acceleration (all axis)
gmax
±2000
g
Supply Voltage
VDD
–0.3 to +3.6
V
Ddrop
1.8
m
Tstg
–40 to +125
°C
(1)
Drop Test
Storage Temperature Range
1. Dropped onto concrete surface from any axis.
ELECTRO STATIC DISCHARGE (ESD)
WARNING: This device is sensitive to electrostatic
discharge.
Although the Freescale accelerometer contains internal
2000 V ESD protection circuitry, extra precaution must be
taken by the user to protect the chip from ESD. A charge of
over 2000 volts can accumulate on the human body or
associated test equipment. A charge of this magnitude can
alter the performance or cause failure of the chip. When
handling the accelerometer, proper ESD precautions should
be followed to avoid exposing the device to discharges which
may be detrimental to its performance.
MMA6270QT
2
Sensors
Freescale Semiconductor
Table 2. Operating Characteristics
Unless otherwise noted: –40°C < TA < 105°C, 2.2 V < VDD < 3.6 V, Acceleration = 0 g, Loaded output(1)
Characteristic
Symbol
Min
Typ
Max
Unit
VDD
IDD
IDD
TA
2.2
—
—
–40
3.3
500
3
—
3.6
800
10
+105
V
µA
µA
°C
gFS
gFS
gFS
gFS
—
—
—
—
±1.5
±2.0
±4.0
±6.0
—
—
—
—
g
g
g
g
VOFF
1.485
1.65
1.815
V
VOFF, TA
VOFF, TA
±2.6(6)
±5.8(6)
±0.6
±5.8
±3.8(7)
±5.9(7)
mg/°C
mg/°C
S1.5g
S2g
S4g
S6g
740
555
277.5
185
800
600
300
200
860
645
322.5
215
mV/g
mV/g
mV/g
mV/g
S, TA
S, TA
±0.02(6)
±0.01(6)
±0.02
±0.01
±0.02(7)
±0.01(7)
%/°C
%/°C
f-3dB
—
350
—
Hz
nRMS
nPSD
—
—
4.7
350
—
—
mVrms
µg/ Hz
tRESPONSE
tENABLE
—
—
1.0
0.5
2.0
2.0
ms
ms
fGCELL
fCLK
—
—
6.0
11
—
—
kHz
kHz
VFSO
VSS+0.25
—
VDD–0.25
V
Nonlinearity, XOUT, YOUT
NLOUT
–1.0
—
+1.0
%FSO
Cross-Axis Sensitivity(10)
VXY, XZ, YZ
—
—
5.0
%
Operating Range(2)
Supply Voltage(3)
Supply Current
Supply Current at Sleep Mode(4)
Operating Temperature Range
Acceleration Range, X-Axis, Y-Axis,
g-Select1 & 2: 00
g-Select1 & 2: 10
g-Select1 & 2: 01
g-Select1 & 2: 11
Output Signal
Zero-g (TA = 25°C, VDD = 3.3 V)(5)
Zero-g(4)
X-axis
Y-axis
Sensitivity (TA = 25°C, VDD = 3.3 V)
1.5 g
2g
4g
6g
Sensitivity(4)
X-axis
Y-axis
Bandwidth Response
XY
Noise
RMS (0.1 Hz – 1 kHz)(4)
Power Spectral Density RMS (0.1 Hz – 1 kHz)(4)
Control Timing
Power-Up Response Time(8)
Enable Response Time(9)
Sensing Element Resonant Frequency
XY
Internal Sampling Frequency
Output Stage Performance
Full-Scale Output Range (IOUT = 30 µA)
1. For a loaded output, the measurements are observed after an RC filter consisting of a 1.0 kΩ resistor and a 0.1 µF capacitor on VDD-GND.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
may operate as a linear device but is not guaranteed to be in calibration.
4. This value is measured with g-Select in 1.5 g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above VDD/2. For negative acceleration, the output will decrease below VDD/2.
6. These values represent the 10th percentile, not the minimum.
7. These values represent the 90th percentile, not the maximum.
8. The response time between 10% of full scale VDD input voltage and 90% of the final operating output voltage.
9. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
10. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity.
MMA6270QT
Sensors
Freescale Semiconductor
3
PRINCIPLE OF OPERATION
The Freescale accelerometer is a surface-micromachined
integrated-circuit accelerometer.
The device consists of two surface micromachined
capacitive sensing cells (g-cell) and a signal conditioning
ASIC contained in a single integrated circuit package. The
sensing elements are sealed hermetically at the wafer level
using a bulk micromachined cap wafer.
The g-cell is a mechanical structure formed from
semiconductor materials (polysilicon) using semiconductor
processes (masking and etching). It can be modeled as a set
of beams attached to a movable central mass that move
between fixed beams. The movable beams can be deflected
from their rest position by subjecting the system to an
acceleration (Figure 3).
As the beams attached to the central mass move, the
distance from them to the fixed beams on one side will
increase by the same amount that the distance to the fixed
beams on the other side decreases. The change in distance
is a measure of acceleration.
The g-cell beams form two back-to-back capacitors
(Figure 3). As the center beam moves with acceleration, the
distance between the beams changes and each capacitor's
value will change, (C = Aε/D). Where A is the area of the
beam, ε is the dielectric constant, and D is the distance
between the beams.
The ASIC uses switched capacitor techniques to measure
the g-cell capacitors and extract the acceleration data from
the difference between the two capacitors. The ASIC also
signal conditions and filters (switched capacitor) the signal,
providing a high level output voltage that is ratiometric and
proportional to acceleration.
Acceleration
Figure 3. Simplified Transducer Physical Model
SPECIAL FEATURES
g-Select
The g-Select feature allows for the selection among 4
sensitivities present in the device. Depending on the logic
input placed on pins 1 and 2, the device internal gain will be
changed allowing it to function with a 1.5 g, 2 g, 4 g, or 6 g
sensitivity (Table 3). This feature is ideal when a product has
applications requiring different sensitivities for optimum
performance. The sensitivity can be changed at anytime
during the operation of the product. The g-Select1 and gSelect2 pins can be left unconnected for applications
requiring only a 1.5 g sensitivity as the device has an internal
pull-down to keep it at that sensitivity (800 mV/g).
Table 3. g-Select Pin Descriptions
g-Select2
g-Select1
g-Range
Sensitivity
0
0
1.5 g
800 mV/g
0
1
2g
600 mV/g
1
0
4g
300 mV/g
1
1
6g
200 mV/g
Sleep Mode
The dual axis accelerometer provides a Sleep Mode that
is ideal for battery operated products. When Sleep Mode is
active, the device outputs are turned off, providing significant
reduction of operating current. A low input signal on pin 12
(Sleep Mode) will place the device in this mode and reduce
the current to 3 uA typ. For lower power consumption, it is
recommended to set g-Select1 and g-Select2 to 1.5 g mode.
By placing a high input signal on pin 12, the device will
resume to normal mode of operation.
Filtering
The dual axis accelerometer contains onboard single-pole
switched capacitor filters. Because the filter is realized using
switched capacitor techniques, there is no requirement for
external passive components (resistors and capacitors) to set
the cut-off frequency.
Ratiometricity
Ratiometricity simply means the output offset voltage and
sensitivity will scale linearly with applied supply voltage. That
is, as supply voltage is increased, the sensitivity and offset
increase linearly; as supply voltage decreases, offset and
sensitivity decrease linearly. This is a key feature when
interfacing to a microcontroller or an A/D converter because
it provides system level cancellation of supply induced errors
in the analog to digital conversion process.
MMA6270QT
4
Sensors
Freescale Semiconductor
BASIC CONNECTIONS
PCB Layout
Pin Descriptions
N/C
POWER SUPPLY
14 13
VDD
VRH
VDD
P0
VSS
1
12
Sleep Mode
g-Select2
2
11
N/C
VSS
Sleep Mode
VDD
3
10
N/C
g-Select1
P1
g-Select2
P2
5
6
7
8
N/C
N/C
9
N/C
4
N/C
VSS
N/C
Figure 4. Pinout Description
Accelerometer
g-Select1
C
C
XOUT
R
YOUT
R
C
C
A/DIN
C
Microcontroller
16 15
YOUT
N/C
XOUT
Top View
A/DIN
Table 4. Pin Descriptions
Pin No.
Pin Name
1
g-Select1
Logic input pin to select g level.
2
g-Select2
Logic input pin to select g level.
3
VDD
Power Supply Input
4
VSS
Power Supply Ground
5-7
N/C
No internal connection.
Leave unconnected.
8 - 11
N/C
Unused for factory trim.
Leave unconnected.
2. Physical coupling distance of the accelerometer to
the microcontroller should be minimal.
12
Sleep Mode
Logic input pin to enable product or
Sleep Mode.
13
N/C
3. The flag underneath the package is internally
connected to ground. It is not recommended for the
flag to be soldered down.
14
YOUT
Y direction output voltage.
15
XOUT
X direction output voltage.
16
N/C
Logic
Inputs
Description
No internal connection.
Leave unconnected
No internal connection.
Leave unconnected.
1
g-Select1
VDD
YOUT
14
0.1 µF
1 kΩ
0.1 µF
4
12
4. Place a ground plane beneath the accelerometer to
reduce noise, the ground plane should be attached to
all of the open ended terminals shown in Figure 6.
5. Use an RC filter with 1.0 kW and 0.1 µF on the
outputs of the accelerometer to minimize clock noise
(from the switched capacitor filter circuit).
7. Accelerometer and microcontroller should not be a
high current path.
MMA6270QT
3
NOTES:
1. To ensure start up operation below 0°C, verify VDD
line has the ability to reach 2.2 V in < 0.1 ms as
measured on the device at the VDD pin. Rise times
greater than this most likely will prevent cold start up
operation.
6. PCB layout of power and ground should not couple
power supply noise.
2 g-Select2
VDD
Figure 6. Recommended PCB Layout for Interfacing
Accelerometer to Microcontroller
VSS
XOUT 15
Sleep Mode
Logic
Input
1 kΩ
8. A/D sampling rate and any external power supply
switching frequency should be selected such that
they do not interfere with the internal accelerometer
sampling frequency (11 kHz for the sampling
frequency). This will prevent aliasing errors.
9. PCB layout should not run traces or vias under the
QFN part. This could lead to ground shorting to the
accelerometer flag.
0.1 µF
Figure 5. Accelerometer with Recommended
Connection Diagram
MMA6270QT
Sensors
Freescale Semiconductor
5
DYNAMIC ACCELERATION
Top View
+Y
14
13
1
12
2
11
3
10
4
9
5
6
7
-X
Bottom
+X
15
Top
16
Side View
Z direction
(For reference only)
8
-Y
: Arrow indicates direction of mass movement.
16-Pin QFN Package
STATIC ACCELERATION
Direction of Earth’s gravity field.*
Top View
Side View
XOUT@ 0g = 1.65 V
YOUT @ -1g = 0.85 V
XOUT @ 0g = 1.65 V
YOUT @ 0g = 1.65 V
XOUT @ -1g = 0.85 V
YOUT @ 0g = 1.65 V
XOUT @ +1g = 2.45 V
YOUT @ 0g = 1.65 V
XOUT @ 0g = 1.65 V
YOUT @ 0g = 1.65 V
XOUT @ 0g = 1.65 V
YOUT @ +1g = 2.45 V
* When positioned as shown, the Earth’s gravity will result in a positive 1g output.
MMA6270QT
6
Sensors
Freescale Semiconductor
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the surface mount packages must be
the correct size to ensure proper solder connection interface
between the board and the package.
With the correct footprint, the packages will self-align when
subjected to a solder reflow process. It is always
recommended to design boards with a solder mask layer to
avoid bridging and shorting between solder pads.
The flag underneath the package is internally connected to
ground. It is not recommended for the flag to be soldered
down.
•
Do not solder down flag for
consumer application
•
Do not place metal pattern or via
structures underneath of package
PCB DESIGN GUIDELINES
The following are the recommended guidelines to follow
for mounting QFN sensors for either automotive or consumer
applications.
1. NSMD (Non Solder Mask Defined) is shown in
Figure 7.
2. Solder mask opening = PCB land pad +0.1 mm.
3. Stencil aperture size = PCB land pad – 0.025mm, as
shown in Figure 8 with a 6 mil stencil.
4. Do not place insertion components or vias at a
distance less than 2mm from the package land area.
5. Signal trace connected to pads should be as
symmetric as possible. Put dummy traces if there is
NC pads, in order to have same length of exposed
trace for all pads. Signal traces with 0.1mm width and
6.
7.
8.
9.
min. 0.5mm length for all PCB land pad near package
are recommended as shown in Figure 7 and
Figure 8. Wider trace can be continued after the
0.5mm zone.
Use a standard pick and place process and
equipment (no hand soldering process).
It is recommended to use a cleanable solder paste
with an additional cleaning step after SMT mount
It is recommended to avoid screwing down the PCB
to fix it into an enclosure since this may cause the
PCB to bend.
PC boards should be rated for multiple reflow of leadfree conditions with 260°C maximum temperature.
PCB land pattern - NSMD
Package Pad
Signal trace 0.1mm width
and 0.5mm (min) length near
package. Wider trace can be
continued after these traces.
0.50 mm
0.55 mm
Cu: 0.55 x 0.50 mm sq.
Solder mask opening =
PCB land pad +0.1mm
=0.65x0.60 mm sq.
Figure 7. NSMD Solder Mask Design Guidelines
MMA6270QT
Sensors
Freescale Semiconductor
7
Signal trace near package: 0.1mm width and
0.5mm (min) length are recommended near
package. Wider trace can be continued after
these.
Stencil opening (black) for land pad (yellow)
= PCB landing pad -0.025mm
= 0.525mmx0,475mm
Package foot pirnt
Figure 8. Stencil Design Guidelines
MMA6270QT
8
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 1 OF 3
CASE 1622-02
ISSUE B
16-LEAD QFN
MMA6270QT
Sensors
Freescale Semiconductor
9
PACKAGE DIMENSIONS
PAGE 2 OF 3
CASE 1622-02
ISSUE B
16-LEAD QFN
MMA6270QT
10
Sensors
Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 3 OF 3
CASE 1622-02
ISSUE B
16-LEAD QFN
MMA6270QT
Sensors
Freescale Semiconductor
11
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc., 2005-2007. All rights reserved.
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical
characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further
information, see http:/www.freescale.com or contact your Freescale sales representative.
For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp.
MMA6270QT
Rev 1
06/2007
Similar pages