ATMEL MMCP-672061HV-15-E Rad. tolerant high speed 16 kb x 9 parallel fifo with programmable flag Datasheet

Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
First-in First-out Dual Port Memory
16384 bits x 9 Organization
Fast Flag and Access Times: 15, 30 ns
Wide Temperature Range: -55°C to +125°C
Programmable Half Full Flag
Fully Expandable by Word Width or Depth
Asynchronous Read/Write Operations
Empty, Full and Half Flags in Single Device Mode
Retransmit Capability
Bi-directional Applications
Battery Back-up Operation: 2V Data Retention
TTL Compatible
Single 5V + 10% Power Supply
No Single Event Latch Up Below an LET threshold of 80 MeV/mg/cm2
Tested up to a Total Dose of 30 Krads (according to MIL-STD-883 TM1019)
Quality grades: QML Q and V with SMD 5962-93177 and ESSC with Specification
9301/48
Description
The M672061H implements a first-in first-out algorithm, featuring asynchronous
read/write operations. The FULL and EMPTY flags prevent data overflow and underflow. The Expansion logic allows unlimited expansion in word size and depth with no
timing penalties. Twin address pointers automatically generate internal read and write
addresses, and no external address information are required for the Atmel FIFOs.
Address pointers are automatically incremented with the write pin and read pin. The 9
bits wide data are used in data communications applications where a parity bit for
error checking is necessary. The Retransmit pin resets the Read pointer to zero without affecting the write pointer. This is very useful for retransmitting data when an error
is detected in the system.
Rad. Tolerant
High Speed
16 Kb x 9
Parallel FIFO with
Programmable
Flag
M672061H
Using an array of eight transistors (8T) memory cell, the M672061H combines an
extremely low standby supply current (typ = 0.1 µA) with a fast access time at 15 ns
over the full temperature range. All versions offer battery backup data retention capability with a typical power consumption at less than 2 µW.
For military/space applications that demand superior levels of performance and reliability the M672061H is processed according to the methods of the latest revision of
the MIL PRF 38535 (Q and V) or ESCC 9000.
4144K-AERO-04/07
1
Block Diagram
Pin Configuration
DIL ceramic 28-pin 300 mils
FP 28-pin 400 mils
2
M672061H
4144K-AERO-04/07
M672061H
Pin Description
Pin Name
Description
I0 - 8
Inputs
Q0 - 8
Outputs
W
Write Enable
R
Read Enable
RS
Reset
EF
Empty Flag
FF
Full Flag
XO/HF
Expansion Out/Half-Full Flag
XI
Expansion IN
FL/RT
First Load/Retransmit
VCC
Power Supply
GND
Ground
Data In (I0 - I8)
Data inputs for 9-bit data
Reset (RS)
Reset occurs whenever the Reset (RS) input is taken to a low state. Reset returns both
internal read and write pointers to the first location. A reset is required after power-up
before a write operation can be enabled. Both the Read Enable (R) and Write Enable
(W) inputs must be in the high state during the period shown in Figure 2 (i.e. tRSS before
the rising edge of RS) and should not change until tRSR after the rising edge of RS.
Otherwise, pulse write (or read) low during the reset operation loads the Programmable
Half Full Flag register from the data Inputs I0 - I8 (or data outputs Q0 - Q8) (shown in figure 2). In these two cases the Full Flag and the Programmable Half Full Flag are
reseted to high and the Empty Flag to low.
Figure 1. Reset (no write to Programmable Half Full Flag register)
Notes:
1. EF, FF and HF may change status during reset, but flags will be valid at tRSC.
2. W and R = VIH around the rising edge of RS.
3
4144K-AERO-04/07
Figure 2. Reset (write (read) to Programmable Half Full Flag register)
Write Enable (W)
A write cycle is initiated on the falling edge of this input if the Full Flag (FF) is not set.
Data set-up and hold times must be maintained in the rise time of the leading edge of
the Write Enable (W). Data is stored sequentially in the Ram array, regardless of any
current read operation.
Once half the memory is filled, and during the falling edge of the next write operation,
the Half-Full Flag (HF) will be set to low and remain in this state until the difference
between the write and read pointers is less than or equal to half of the total available
memory in the device. The Half-Full Flag (HF) is then reset by the rising edge of the
read operation.
To prevent data overflow, the Full Flag (FF) will go low, inhibiting further write operations. On completion of a valid read operation, the Full Flag (FF) will go high after TRFF,
allowing a valid write to begin. When the FIFO stack is full, the internal write pointer is
blocked from W, so that external changes to W will have no effect on the full FIFO stack.
Read Enable (R)
A read cycle is initiated on the falling edge of the Read Enable (R) provided that the
Empty Flag (EF) is not set. The data is accessed on a first in/first out basis, not including
any current write operations. After Read Enable (R) goes high, the Data Outputs
(Q0 - Q8) will return to a high impedance state until the next Read operation. When all
the data in the FIFO stack has been read, the Empty Flag (EF) will go low, allowing the
“final” read cycle, but inhibiting further read operations while the data outputs remain in
a high impedance state. Once a valid write operation has been completed, the Empty
Flag (EF) will go high after tWEF and a valid read may then be initiated. When the FIFO
stack is empty, the internal read pointer is blocked from R, so that external changes to R
will have no effect on the empty FIFO stack.
First Load/Retransmit
(FL/RT)
This is a dual-purpose input. In the Depth Expansion Mode, this pin is connected to
ground to indicate that it is the first loaded (see Operating Modes). In the Single Device
Mode, this pin acts as the retransmit input. The Single Device Mode is initiated by connecting the Expansion In (XI) to ground.
The M672061H can be set to retransmit data when the Retransmit Enable Control (RT)
input is pulsed low. A retransmit operation will set the internal read point to the first location and will not affect the write pointer. Read Enable (R) and Write Enable (W) must be
in the high state during retransmit. The retransmit feature is intended for use when a
number of writes are equal to or less than the depth of the FIFO has occured since the
last RS cycle. The retransmit feature is not compatible with the Depth Expansion Mode
and will affect the Half-Full Flag (HF), in accordance with the relative locations of the
read and write pointers.
4
M672061H
4144K-AERO-04/07
M672061H
Expansion In (XI)
This input is a dual-purpose pin. Expansion In (XI) is connected to GND to indicate an
operation in the single device mode. Expansion In (XI) is connected to Expansion Out
(XO) of the previous device in the Depth Expansion or Daisy Chain modes.
Full Flag (FF)
The Full Flag (FF) will go low, inhibiting further write operations when the write pointer is
one location less than the read pointer, indicating that the device is full. If the read
pointer is not moved after Reset (RS), the Full Flag (FF) will go low after 16384 writes.
Empty Flag (EF)
The Empty Flag (EF) will go low, inhibiting further read operations when the read pointer
is equal to the write pointer, indicating that the device is empty.
Expansion Out/Half-full
Flag (XO/HF)
This is a dual-purpose output. In the single device mode, when Expansion In (XI) is connected to ground, this output acts as an indication of a half-full memory.
The M672061H offers a variable offset for the Half Full condition. The offset is loaded
into a register during a reset cycle. When RS is low, the Programmable Half Full Flag
(PHF) can be loaded from the DATA inputs I0 - I8 by pulsing W low or from the DATA
outputs Q0 - Q8 by pulsing R low. The offset options are listed in table 1. If PHF is not
loaded during the reset cycle, the default offset will be the half of the total memory of the
device.
The Programmable Half-Full Flag (PHF) will be set to low and will remain set until the
difference between the write and read pointers is less than or equal to the Programmable offset (if the Half Full Flag register has been loaded during the reset cycle) or the half
of the total memory (if the Half Full register has not been loaded during the reset cycle).
After half the memory is filled and on the falling edge of the next write operation, the
Half-Full Flag (HF) will be set to low and will remain set until the difference between the
write and read pointers is less than or equal to half of the total memory of the device.
The Half-Full Flag (HF) is then reset by the rising edge of the read operation.
In the Depth Expansion Mode, Expansion In (XI) is connected to Expansion Out (XO) of
the previous device. This output acts as a signal to the next device in the Daisy Chain by
providing a pulse to the next device when the previous device reaches the last memory
location.
Data Output (Q0 - Q8)
DATA output for 9-bit wide data. This data is in a high impedance condition whenever
Read (R) is in a high state.
5
4144K-AERO-04/07
Functional Description
Single Device Mode
A single M672061H may be used when the application requirements are for 16384
words or less. The M672061H is in a Single Device Configuration when the Expansion In (XI)
control input is grounded (see Figure 3). In this mode the Half-Full Flag (HF), which is an active
low output, is shared with Expansion Out (XO).
Figure 3. Block Diagram of Single 16384 × 9
HF
(HALF-FULL FLAG)
(W)
WRITE
(R)
READ
HF
9
DATAIN
9
(I)
FULL FLAG (FF)
(EF)
EMPTY FLAG
(RS)
(RT)
RETRANSMIT
RESET
EXPANSION IN (XI)
Width Expansion Mode
DATAOUT
(Q)
M672061H
Word width may be increased simply by connecting the corresponding input control signals of multiple devices. Status flags (EF, FF and HF) can be detected from any device.
Figure 4 demonstrates an 18-bit word width by using two M672061H. Any word width can be
attained by adding additional M672061H.
Figure 4. Block Diagram of 16384 bits x 18 FIFO Memory Used in Width Expansion Mode
Note:
6
Flag detection is accomplished by monitoring the FF, EF and the HF signals on either (any) device used in the width expansion
configuration. Do not connect any output control signals together.
M672061H
4144K-AERO-04/07
M672061H
Table 1. Programmable Half Full Flag Offset
I8
I7
I6
I5
I4
I3
I2
I1
I0
Offset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
32
0
0
0
0
0
0
0
1
0
64
0
0
0
0
0
0
0
0
8192 (Half Full)
Default Offset
1
1
1
1
1
1
1
1
0
16384-64
1
1
1
1
1
1
1
1
1
16384-32
...
1
...
Table 2. Reset and Retransmit Single Device Configuration/Width Expansion Mode
Inputs
Mode
Internal Status
Outputs
RS
RT
XI
Read Pointer
Write Pointer
EF
FF
HF
Reset
0
X
0
Location Zero
Location Zero
0
1
1
Retransmit
1
0
0
Location Zero
Unchanged
X
X
X
Read/Write
1
1
0
Increment(1)
Increment(1)
X
X
X
Note:
1. Pointer will increment if flag is high.
Table 3. Reset and First Load Truth Table
Depth Expansion/Compound Expansion Mode
Inputs
Mode
Internal Status
Outputs
RS
FL
XI
Read Pointer
Write Pointer
EF
FF
Reset First Device
0
0
(1)
Location Zero
Location Zero
0
1
Reset All Other Devices
0
1
(1)
Location Zero
Location Zero
0
1
X
(1)
X
X
X
X
Read/Write
Note:
1
1. XI is connected to XO of previous device.
See Figure 5.
7
4144K-AERO-04/07
Depth Expansion (Daisy
Chain) Mode
The M672061H can be easily adapted for applications which require more than 16384
words. Figure 5 demonstrates Depth Expansion using three M672061H. Any depth can
be achieved by adding additional 672061H.
The M672061H operates in the Depth Expansion configuration if the following conditions are met:
1. The first device must be designated by connecting the First Load (FL) control
input to ground.
2. All other devices must have FL in the high state.
3. The Expansion Out (XO) pin of each device must be connected to the Expansion In
(XI) pin of the next device. See Figure 5.
4. External logic is needed to generate a composite Full Flag (FF) and Empty Flag
(EF). This requires that all EF’s and all FFs be ORed (i.e. all must be set to generate the
correct composite FF or EF). See Figure 5.
5. The Retransmit (RT) function and Half-Full Flag (HF) are not available in the Depth
Expansion Mode.
Compound Expansion
Module
It is quite simple to apply the two expansion techniques described above together to create large FIFO arrays (see Figure 6).
Bidirectional Mode
Applications which require data buffering between two systems (each system being
capable of Read and Write operations) can be created by coupling M672061H as shown
in Figure 7 Care must be taken to ensure that the appropriate flag is monitored by each
system (i.e. FF is monitored on the device on which W is in use; EF is monitored on the device
on which R is in use). Both Depth Expansion and Width Expansion may be used in this mode.
Data Flow – Through
Modes
Two types of flow-through modes are permitted: a read flow-through and a write flowthrough mode. In the read flow-through mode (Figure 18) the FIFO stack allows a single
word to be read after one word has been written to an empty FIFO stack. The data is
enabled on the bus at (tWEF + tA) ns after the leading edge of W which is known as the
first write edge and remains on the bus until the R line is raised from low to high, after which the
bus will go into a three-state mode after tRHZ ns. The EF line will show a pulse indicating temporary reset and then will be set. In the interval in which R is low, more words may be written to
the FIFO stack (the subsequent writes after the first write edge will reset the Empty Flag) ; however, the same word (written on the first write edge) presented to the output bus as the read
pointer will not be incremented if R is low. On toggling R, the remaining words written to the
FIFO will appear on the output bus in accordance with the read cycle timings.
In the write flow-through mode (Figure 19), the FIFO stack allows a single word of data
to be written immediately after a single word of data has been read from a full FIFO
stack. The R line causes the FF to be reset, but the W line, being low, causes it to be set again
in anticipation of a new data word. The new word is loaded into the FIFO stack on the leading
edge of W. The W line must be toggled when FF is not set in order to write new data into the
FIFO stack and to increment the write pointer.
8
M672061H
4144K-AERO-04/07
M672061H
Figure 5. Block Diagram of 49152 x 9 FIFO Memory (Depth Expansion)
M672061H
M672061H
M672061H
Figure 6. Compound FIFO Expansion
Notes:
1. For depth expansion block see section on Depth Expansion and Figure 4.
2. For Flag detection see section on Width Expansion and Figure 3
Figure 7. Bidirectional FIFO Mode
H
H
9
4144K-AERO-04/07
Electrical Characteristics
Absolute Maximum Ratings
*NOTICE:
Supply voltage (VCC - GND): ............................. -0.5V to 7.0V
Input or Output voltage applied: ... (GND -0.3V) to (Vcc +0.3V)
Storage temperature:.................................... -65 °C to +150°C
Stresses beyond those listed under "Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
DC Parameters
Table 4. DC Test Conditions
TA = -55°C to +125°C; Vss = 0V; Vcc = 4.5V to 5.5V
Parameter
Notes:
ICCOP (1)
Operating supply current
ICCSB(2)
Standby supply current
ICCPD(3)
Power down current
M672061H-15
Unit
Value
110
120
mA
Max
5
5
mA
Max
400
400
µA
Max
Description
M672061H
Unit
Value
ILI(1)
Input leakage current
±1
µA
Max
ILO(2)
Output leakage current
±1
µA
Max
VIL(3)
Input low voltage
0.8
V
Max
VIH(3)
Input high voltage
2.2
V
Min
VOL(4)
Output low voltage
0.4
V
Max
VOH(4)
Output high voltage
2.4
V
Min
Input capacitance
8
pF
Max
Output capacitance
8
pF
Max
C IN
(5)
C OUT(5)
10
M672061H-30
1. Icc measurements are made with outputs open.
2. R = W = RS = FL/RT = VIH.
3. All input = Vcc
Parameter
Notes:
Description
1.
2.
3.
4.
5.
0.4 ≤ Vin ≤ Vcc.
R = VIH, 0.4 ≤ VOUT ≤ VCC.
VIH max = Vcc + 0.3V. VIL min = -0.3V or -1V pulse width 50 ns. For XI input, VIH= 2.8V
Vcc min, IOL = 8 mA, IOH = -2 mA
Guaranteed but not tested.
M672061H
4144K-AERO-04/07
M672061H
AC Parameters
AC Test Conditions
Input pulse levels: Gnd to 3.0V
Input rise/Fall times: 5 ns
Input timing reference levels: 1.5V
Output reference levels: 1.5V
Output load: See Figure 8
Figure 8. Output Load
(1)
Note:
1. Includes jig and scope capacitance.
Table 5. AC Test Conditions
Symbol (1)
Symbol (2)
Parameter (3) (4)
M672061H- 30
M672061H- 15
Min
Max
Min
Max
40
-
25
-
ns
-
30
-
15
ns
Unit
Read Cycle
TRLRL
tRC
Read cycle time
TRLQV
tA
TRHRL
tRR
Read recovery time
10
-
10
-
ns
TRLRH
tRPW
Read pulse width (5)
30
-
15
-
ns
TRLQX
tRLZ
Read low to data low Z (6)
0
-
0
-
ns
TWHQX
tWLZ
Write low to data low Z (6) (7)
5
-
3
-
ns
TRHQX
tDV
Data valid from read high
5
-
5
-
ns
TRHQZ
tRHZ
Read high to data high Z (6)
-
20
-
15
ns
TWLWL
tWC
Write cycle time
40
-
25
-
ns
TWLWH
tWPW
Write pulse width(5)
30
-
15
-
ns
TWHWL
tWR
Write recovery time
10
-
10
-
ns
TDVWH
tDS
Data set-up time
18
-
9
-
ns
TWHDX
tDH
Data hold time
0
-
0
-
ns
Reset cycle time
40
-
25
-
ns
Reset pulse width (5)
30
-
15
-
ns
Reset set-up time
30
-
20
-
ns
Access time
Write Cycle
Reset Cycle
TRSLWL
tRSC
TRSLRSH
tRS
TWHRSH
tRSS
11
4144K-AERO-04/07
Table 5. AC Test Conditions (Continued)
Symbol (1)
TRSHWL
Symbol (2)
Parameter (3) (4)
M672061H- 30
M672061H- 15
Min
Max
Min
Max
Unit
tRSR
Reset recovery time
10
–
10
–
ns
TRTLWL
tRTC
Retransmit cycle time
40
–
25
–
ns
TRTLRTH
tRT
Retransmit pulse width(5)
30
–
15
–
ns
TWHRTH
tRTS
Retransmit set-up time(6)
30
–
15
–
ns
TRTHWL
tRTR
Retransmit recovery time
10
–
10
–
ns
TRSLEFL
tEFL
Reset to EF low
–
30
–
25
ns
TRSLFFH
tHFH, tFFH
Reset to HF/FF high
–
30
–
25
ns
TRLEFL
tREF
Read low to EF low
–
30
–
25
ns
TRHFFH
tRFF
Read high to FF high
–
30
–
25
ns
TEFHRH
tRPE
Read width after EF high
30
–
15
–
ns
TWHEFH
tWEF
Write high to EF high
–
30
–
15
ns
TWLFFL
tWFF
Write low to FF low
–
30
–
20
ns
TWLHFL
tWHF
Write low to HF low
–
30
–
30
ns
TRHHFH
tRHF
Read high to HF high
–
30
–
30
ns
TFFHWH
tWPF
Write width after FF high
30
–
15
–
ns
TWLXOL
tXOL
Read/Write to XO low
–
30
–
15
ns
TWHXOH
tXOH
Read/Write to XO high
–
30
–
15
ns
TXILXIH
tXI
XI pulse width
30
–
15
–
ns
TXIHXIL
tXIR
XI recovery time
10
–
10
–
ns
TXILRL
tXIS
XI set-up time
10
–
10
–
ns
Retransmit Cycle
Flags
Expansion
1.
2.
3.
4.
5.
6.
7.
12
STD symbol.
ALT symbol.
Timings referenced as in ac test conditions.
All parameters tested only.
Pulse widths less than minimum value are not allowed.
Values guaranteed by design, not currently tested.
Only applies to read data flow-through mode.
M672061H
4144K-AERO-04/07
M672061H
Figure 9. Asynchronous Write and Read Operation
Figure 10. Full Flag from Last Write to First Read
Figure 11. Empty Flag from Last Read to First Write
13
4144K-AERO-04/07
Figure 12. Retransmit
Note:
1. EF, FF and PHF may change status during Retransmit, but flags will be valid at tRTC
Figure 13. Empty Flag Timing
W
t
WEF
EF
t
RPE
R
Figure 14. Full Flag Timing
14
M672061H
4144K-AERO-04/07
M672061H
Figure 15. Programmable Half-Full Flag Timing
Figure 16. Expansion Out
Figure 17. Expansion In
15
4144K-AERO-04/07
Figure 18. Read Data Flow - Through Mode
Figure 19. Write Data Flow - Through Mode
16
M672061H
4144K-AERO-04/07
M672061H
Ordering Information
Reference Number
Temperature Range
Speed
Package
Quality Flow
MMCP-672061HV-15-E(1)
25°C
15 ns
SB28.3
Engineering Samples
SMCP-672061HV-15SCC
-55 to +125°C
15 ns
SB28.3
ESCC
SMCP-672061HV-30SCC
-55 to +125°C
30 ns
SB28.3
ESCC
5962-9317710QTC
-55 to +125°C
15 ns
SB28.3
QML Q
5962-9317709QTC
-55 to +125°C
30 ns
SB28.3
QML Q
5962-9317710VTC
-55 to +125°C
15 ns
SB28.3
QML V
5962-9317709VTC
-55 to +125°C
30 ns
SB28.3
QML V
5962D9317710VTC
-55 to +125°C
15 ns
SB28.3
QML V RHA
5962D9317709VTC
-55 to +125°C
30 ns
SB28.3
QML V RHA
25°C
15 ns
FP28.4
Engineering Samples
SMDP-672061HV-15SCC
-55 to +125°C
15 ns
FP28.4
ESCC
SMDP-672061HV-30SCC
-55 to +125°C
30 ns
FP28.4
ESCC
5962-9317710QNC
-55 to +125°C
15 ns
FP28.4
QML Q
5962-9317709QNC
-55 to +125°C
30 ns
FP28.4
QML Q
5962-9317710VNC
-55 to +125°C
15 ns
FP28.4
QML V
5962-9317709VNC
-55 to +125°C
30 ns
FP28.4
QML V
5962D9317710VNC
-55 to +125°C
15 ns
FP28.4
QML V RHA
5962D9317709VNC
-55 to +125°C
30 ns
FP28.4
QML V RHA
25°C
15 ns
Die
Engineering Samples
-55 to +125°C
15 ns
Die
QML V
MMDP-672061HV-15-E
MM0 -672061HV-15-E(1)
MM0 -672061HV-15SV
Note:
(1)
1. Contact Atmel for availability.
17
4144K-AERO-04/07
Package Drawings
28-lead Side Braze (300 mils)
18
M672061H
4144K-AERO-04/07
M672061H
28-lead Flat Pack (400 mils)
19
4144K-AERO-04/07
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
e-mail
[email protected]
Web Site
http://www.atmel.com
Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard
warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any
errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and
does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are
granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use
as critical components in life support devices or systems.
©2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and Everywhere You Are ® are the trademarks or registered trademarks, of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
4144K-AERO-04/07
/xM
Similar pages