Panasonic MN39260FH 4.5 mm (type-1/4) 810k-pixel ccd area image sensor Datasheet

CCD Area Image Sensor
MN39260FH
4.5 mm (type-1/4) 810k-pixel CCD Area Image Sensor
■ Overview
■ Pin Assignments
The MN39260FH is a 4.5 mm (type-1/4) interline
transfer CCD (IT-CCD) solid state image sensor device.
This device uses photodiodes in the optoelectric conversion section and CCDs for signal readout. The electronic shutter function has made an exposure time of 1/10 000
seconds possible. Further, this device has the features of
high sensitivity, low noise, broad dynamic range, and low
smear.
This device has a total of 802 579 pixels (1 007 horizontal × 797 vertical) and provides stable and clear images
with a resolution of 600 horizontal TV-lines and 420 vertical TV-lines.
Part Number
Size
MN39260FH 4.5 mm (type-1/4)
φV4
1
14
PT
φV3
2
13
Sub
φV2
3
12
φH2
φV1
4
11
φH1
GND
5
10
φR
TEST
6
9
GND
VDD
7
8
VO
System Color or B/W
PAL
Color
(Top View)
■ Features
• Effective pixel number 962 (horizontal) × 774 (vertical)
• High sensitivity
• Broad dynamic range
• Low smear
• Electronic shutter
■ Applications
• Camcorders
• FA, OA cameras
Publication date: September 2001
SMD00004BEC
1
MN39260FH
■ Block Diagram
(4 columns OB + 962 columns valid area + 41 columns OB)
1
φV4
2 φ
V3
3 φ
8
VO
7
VDD
9
GND
(2 dummies + OB11 + valid area 774 + OB12 )
Output section
13
4
Vertical shift register
Sub
Photo diode
V2
φV1
5
GND
6 TEST *1
14
PT
12
φH2
11
φH1
φR
10
Horizontal register (one dummy at the front, no dummy at the back)
*1 : TEST pin must be left open, because the pin outputs CCD internal bias voltage.
■ Pin Descriptions
Pin No. Symbol
1
φV4
2
3
Description
Pin No. Symbol
Description
Vertical shift register clock pulse 4
8
VO
φV3
Vertical shift register clock pulse 3
9
GND
φV2
Vertical shift register clock pulse 2
10
φR
Reset pulse (RG)
Vertical shift register clock pulse 1
11
φH1
Horizontal register clock pulse 1
GND
12
φH2
Horizontal register clock pulse 2
13
Sub
Substrate
14
PT
P-well for protection circuit
4
φV1
5
GND
6
TEST
7
VDD
TEST pin (OPEN)
*1
Power supply
Video output
GND
Note) *1: TEST pin must be left open, because the pin outputs CCD internal bias voltage.
■ Device Parameter (H × V)
Parameter
Value
Unit
*1
962 × 774
pixel
Image sensing block dimension
3.703 7 × 2.709 0
mm2
3.85 × 3.50
µm2
Pixel number
Pixel dimension
Note) *1: OB columns are not included.
2
SMD00004BEC
MN39260FH
■ Absolute Maximum Ratings and Operating Conditions
Absolute maximum rating
Parameter
Lower limit
VDD
VPT
*3, 4
GND
Upper limit
High-Low
VφH2
VSub
Max
Unit
18
14.5
15.0
15.5
V
0.2
−7.5
−7.0
−6.5
V

0

V
3.0
3.3
3.6
V

8
(Supplied internally)
V
High

8
3.0
3.3
3.6
V
Low
− 0.2

− 0.2
0
0.2
V
High

8
3.0
3.3
3.6
V
Low
− 0.2

− 0.2
0
0.2
V
*2
φVSub
Typ
− 0.2
Bias
VφH1
Min
−10.0
(Reference voltage)
VφR
Operating condition
(Supplied internally)
V
− 0.2
35
21.0
22.0
23.0
V
High

18
14.5
15.0
15.5
V
Middle


− 0.05
0
0.05
V
Low
−9

−7.5
−7.0
−6.5
V
Middle

15
− 0.05
0
0.05
V
Low
−9

−7.5
−7.0
−6.5
V
High

18
14.5
15.0
15.5
V
Middle


− 0.05
0
0.05
V
Low
−9

−7.5
−7.0
−6.5
V
Middle

15
− 0.05
0
0.05
V
Low
−9

−7.5
−7.0
−6.5
V
Operating temperature
−10
60

25

°C
Storage temperature
−30
80



°C
VφV1
*1
*3, 4
VφV2
*3, 4
VφV3
*3, 4
VφV4
*3, 4
SMD00004BEC
3
MN39260FH
■ Absolute Maximum Ratings and Operating Conditions (continued)
Note) 1. Standard photo detecting condition
Standard photo detecting condition stands for detecting image with a light source of color temperature of 2 856K, luminance
of 1 050 cd/m2, and using a color temperature conversion filter LB-40 (HOYA), infrared cut filter CAW-500S with thickness
2.5 mm for a light path and with F8 lens aperture. The quantity of the incidental light to a photo-detecting surface under the
above condition is defined as the standard quantity of light.
2. *1: VSub when using electronic shutter function
φVSub H
φVSub (V)
φVSub L
VSub (V)
(Supplied internally)
GND
* φSub pulse generates once every 1 V period.
*2: VSub supplied internally is the voltage suppressing the blooming generation at ×500 light quantity relative to the
standard light quantity.
*3: Relation between VPT and VφVL
Set VPT under the following condition against VL of a vertical transfer clock waveform.
VPT ≤ VL (VφV1L to VφV4L)
− 0.2 < VφV − VPT < 24.5 (V)
*4: Absolute maximum ratings
■ Optical Characteristics
Parameter
Symbol
Carrier saturation output
Sc
Sensitivity
Vertical smear
Conditions
Min
Typ
Max
Unit
J chart
500


mV
So
J chart F1.4, 1/32 ND
80
110

mV
Sm
1/10 V chart, F1.4


0.01
%
Note) The above-mentioned characteristics are the values on driving the device for the imaging stabilizer mode (1/60 seconds
accumulation).
4
SMD00004BEC
MN39260FH
■ Timing Diagram
• High speed pulse timing
φH1
50%
50%
50%
27.8 ns ± 3 ns
CCD output
φR
50%
50%
1 ns ± 3 ns
Clamp pulse
(DS1)
10 ns ∼ 13.9 ns
50%
50%
3 ns ± 3 ns
Sampling pulse
(DS2)
50%
4 ns ± 3 ns
SMD00004BEC
13.9 ns ± 3 ns
50%
13.9 ns ± 3 ns
5
MN39260FH
■ Timing Diagram (continued)
• Rise time and fall time of each pulse
φV1 , φV3
0.9
0.9
0.1
0.1
0.9
0.9
0.1
0.1
≤300 ns
≤300 ns
φV2 , φV4
≤300 ns
0.9
0.9
0.1
0.1
≤300 ns
φH1 , φH2
0.9
0.1
0.1
≤8 ns
6
≤300 ns
φR
0.9
≤300 ns
0.9
0.9
0.1
0.1
≤8 ns
≤6 ns
SMD00004BEC
≤6 ns
MN39260FH
■ Color Filter Arrays on CCD
774
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
773
Mg
G
Mg
G
Mg
G
Mg
G
Mg
G
8
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
7
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
6
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
5
Mg
G
Mg
G
Mg
G
Mg
G
Mg
G
4
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
3
G
Mg
G
Mg
G
Mg
G
Mg
G
Mg
2
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
Cy
Ye
1
Mg
G
Mg
G
Mg
G
Mg
G
Mg
G
1
2
3
4
5
6
7
8
961 962
■ Graph of Characteristics
CCD color filter spectral characteristics
1.2
Ye
1.0
Relative sensitivity
0.8
0.6
Gr
Cy
0.4
Mg
0.2
0
400
450
500
550
600
650
700
750
800
Wavelength (nm)
SMD00004BEC
7
MN39260FH
■ Package Dimensions (unit: mm)
• WDIP014-P-0400H
10.00±0.08
9.00±0.10
5.00±0.08
Reference plane
8
1.27
(1.19)
0.30±0.05
(2.50)
2-R0.40 (depth 0.30)
14
8
10.16±0.25
0.3 M
7
(2.50)
1
1.30±0.10
3.50±0.20
(0.60)
0.25±0.05
(0.7)
7
(1.30)
1
3.3±0.15
Valid pixel center
0.015
5.00±0.08
9.00±0.10
10.00±0.08
14
8
1. The center of the package is equal to the center of the effective
pixel area.
2. The rotation angle of the effective pixel area: up to ±1.0 degree
3. The distance from the bottom face of the package to the surface
of the effective pixel area: 1.41 mm ± 0.1 mm
4. The tilt of the effective pixel area for the bottom face of the
package: up to 25 µm
5. Thickness of seal glass is 0.7 mm ± 0.1 mm, and the refractive
index is 1.50.
6. Package weight: 0.55 g (typ.)
SMD00004BEC
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government
if any of the products or technologies described in this material and controlled under the "Foreign
Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the
product or technologies as described in this material.
(4) The products described in this material are intended to be used for standard applications or general
electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without
notice for modification and/or improvement. At the final stage of your design, purchasing, or use of
the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that
the latest specifications satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of
incidence of break down and failure mode, possible to occur to semiconductor products. Measures
on the systems such as redundant design, arresting the spread of fire or preventing glitch are
recommended in order to prevent physical injury, fire, social damages, for example, by using the
products.
(7) When using products for which damp-proof packing is required, observe the conditions (including
shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets
are individually exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL
Similar pages