Rohm MNR04M0ABJ000 Chip resistor network Datasheet

MNR04
Resistors
Chip resistor networks
MNR04 (1005 × 4 size)
!Features
1) Extremely small and light
Area ratio is 60% smaller than that of chip 3216 (MNR14), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than four 1005 chips (MCR01), and mounting costs are lower.
3) Can be mounted on a wide variety of devices
Squared corners make it excellent for mounting on image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors comply with the international standard ISO-9001.
Furthermore, changes to the design and specifications of products may occur without notice. Therefore, before
ordering or using this product, please make sure to reconfirm the specification sheet before ordering or using this
product.
!Ratings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
0.063W (1 / 16W)
at 70°C
POWER LOAD (%)
100
80
60
40
20
0
Ð 55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the
value obtained exceeds the limiting element voltage, the voltage
rating is equal to maximum operating voltage.
E = P×R
Nominal resistance
Operating temperature
E : Voltage rating (V)
P : Power rating (W)
R : Nominal resistance (Ω)
Limiting element voltage 25V
See Table 1.
−55°C~+125°C
1/4
MNR04
Resistors
Jumper type
Resistance
Rated current
Operating temperature
Table 1
Max.50mΩ
1A
−55°C~+125°C
Resistance range
(Ω)
Resistance tolerance
J (±5%)
10≤R≤1M
Resistance temperature
coefficient (ppm / °C)
(E24)
±300
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
!Characteristics
Item
Resistance
Guaranteed value
Resistor type
Jumper type
J : ±5%
Max. 50mΩ
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
See Table.1
± (2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
± (1.0%+0.05Ω)
Max. 50mΩ
No remarkable abnormality on the appearance.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
± (1.0%+0.05Ω)
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C~+125°C 5cyc
± (3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h~1,048h
± (3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h~1,048h
± (3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h~1,048h
± (1.0%+0.05Ω)
Max. 50mΩ
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
Test conditions (JIS C 5201-1)
Max. 50mΩ
± (1.0%+0.05Ω)
Without mechanical damage such as breaks.
JIS C 5201-1 4.33
2/4
MNR04
Resistors
!External dimensions (Units: mm)
2.0±0.2
a
b
B
a : 0.4±0.15
b : 0.3±0.15
No.
Material
0.2±0.15
A'
0.2±0.15
A
1.0±0.1
Thick dielectric glaze of Ruthenium
Thick film of silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with Sn/Pb or Sn
∗
0.5
∗
0.5
∗
Alumina substrate
0.5
B'
0.45±0.1
Overcoating
Cross section A - A'
Cross section B - B'
∗ The pitch between electrodes.
!Equivalent circuit
R1
R2
R3
R4
R1 = R2 = R3 = R4
3/4
MNR04
Resistors
!Packaging
Reel
Taping
P0
P2
φD0
E
F
W
02
04
06
08
06
D
04
B
02
A
08
B0
A0
P1
Heat crimp cover / Tape
Chip network resistors
Thick paper mount
(Underside paper tape)
Square punchout hole
T2
C
(Units : mm)
Label
EIAJ ET-7200A compliant
(Units : mm)
A
φ180
B
0
−3
φ60
C
+1
0
9
+1.0
0
W
F
E
A0
B0
8.0±0.3
3.5±0.05
1.75±0.1
1.2±0.1
2.2±0.1
D0
P0
P1
P2
T2
φ1.5 +0.1
0
4.0±0.1
2.0±0.1
2.0±0.05
Max. 0.5
D
φ13±0.2
!Product designation
Part no.
Packaging / Processing specifications
Code
M0
Part no. Packaging
Taping
MNR02 / 04
Package style
Paper tape with reel (10,000)
Circuit configuration Resistance
code
tolerance
AB MNR04 / 12 / 14 / 32 / 34
J
±5%
Nominal resistance
3-digit IEC coding system
4/4
Similar pages