Freescale MPC5565MVZ80R Microcontroller Datasheet

Document Number: MPC5565
Rev. 2.0, 11/2008
Freescale Semiconductor
Data Sheet: Technical Data
MPC5565
Microcontroller Data Sheet
by: Microcontroller Division
This document provides electrical specifications, pin
assignments, and package diagrams for the MPC5565
microcontroller device. For functional characteristics,
refer to the MPC5565 Microcontroller Reference
Manual.
1
Contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . 5
3.3 Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 EMI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 ESD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 VRC and POR Electrical Specifications . . . . . . . . . 9
3.7 Power-Up/Down Sequencing. . . . . . . . . . . . . . . . . 10
3.8 DC Electrical Specifications . . . . . . . . . . . . . . . . . 13
3.9 Oscillator and FMPLL Electrical Characteristics . . 20
3.10 eQADC Electrical Characteristics . . . . . . . . . . . . . 22
3.11 H7Fa Flash Memory Electrical Characteristics . . . 23
3.12 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.13 AC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4
Mechanicals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.1 MPC5565 324 PBGA Pinouts . . . . . . . . . . . . . . . . 46
4.2 MPC5565 324-Pin Package Dimensions. . . . . . . . 47
5
Revision History for the MPC5565 Data Sheet . . . . . . . 49
5.1 Changes to Revision 1.0 in Revision 2.0 . . . . . . . . 49
5.2 Changes to Revision 0.0 in Revision 1.0 . . . . . . . . 52
Overview
The MPC5565 microcontroller (MCU) is a member of
the MPC5500 family of microcontrollers built on the
Power Architecture™ embedded technology. This
family of parts has many new features coupled with high
performance CMOS technology to provide substantial
reduction of cost per feature and significant performance
improvement over the MPC500 family.
The host processor core of this device complies with the
Power Architecture embedded category that is 100%
user-mode compatible (including floating point library)
with the original Power PC™ user instruction set
architecture (UISA). The embedded architecture
enhancements improve the performance in embedded
applications. The core also has additional instructions,
including digital signal processing (DSP) instructions,
beyond the original Power PC instruction set.
© Freescale Semiconductor, Inc., 2008. All rights reserved.
Overview
The MPC5500 family of parts contains many new features coupled with high performance CMOS
technology to provide significant performance improvement over the MPC565.
The host processor core of the MPC5565 also includes an instruction set enhancement allowing variable
length encoding (VLE). This allows optional encoding of mixed 16- and 32-bit instructions. With this
enhancement, it is possible to significantly reduce the code size footprint.
The MPC5565 has two levels of memory hierarchy. The fastest accesses are to the 8-kilobytes (KB)
unified cache. The next level in the hierarchy contains the 80-KB on-chip internal SRAM and
two-megabytes (MB) internal flash memory. The internal SRAM and flash memory hold instructions and
data. The external bus interface is designed to support most of the standard memories used with the
MPC5xx family.
The complex input/output timer functions of the MPC5565 are performed by an enhanced time processor
unit (eTPU) engine. The eTPU engine controls 32 hardware channels. The eTPU has been enhanced over
the TPU by providing: 24-bit timers, double-action hardware channels, variable number of parameters per
channel, angle clock hardware, and additional control and arithmetic instructions. The eTPU is
programmed using a high-level programming language.
The less complex timer functions of the MPC5565 are performed by the enhanced modular input/output
system (eMIOS). The eMIOS’ 24 hardware channels are capable of single-action, double-action,
pulse-width modulation (PWM), and modulus-counter operations. Motor control capabilities include
edge-aligned and center-aligned PWM.
Off-chip communication is performed by a suite of serial protocols including controller area networks
(FlexCANs), enhanced deserial/serial peripheral interfaces (DSPIs), and enhanced serial communications
interfaces (eSCIs). The DSPIs support pin reduction through hardware serialization and deserialization of
timer channels and general-purpose input/output (GPIOs) signals.
The MCU has an on-chip enhanced queued dual analog-to-digital converter (eQADC). The 324 package
has 40-channels.
The system integration unit (SIU) performs several chip-wide configuration functions. Pad configuration
and general-purpose input and output (GPIO) are controlled from the SIU. External interrupts and reset
control are also determined by the SIU. The internal multiplexer submodule provides multiplexing of
eQADC trigger sources, daisy chaining the DSPIs, and external interrupt signal multiplexing.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
2
Freescale Semiconductor
Ordering Information
2
Ordering Information
M PC 5565 M ZQ 80 R
Qualification status
Core code
Device number
Temperature range
Package identifier
Operating frequency (MHz)
Tape and reel status
Temperature Range
M = –40° C to 125° C
Package Identifier
ZQ = 324PBGA SnPb
VZ = 324PBGA Pb-free
Operating Frequency
80 = 80 MHz
112 = 112 MHz
132 = 132 MHz
Tape and Reel Status
R = Tape and reel
(blank) = Trays
Qualification Status
P = Pre qualification
M = Fully spec. qualified, general market flow
S = Fully spec. qualified, automotive flow
Note: Not all options are available on all devices. Refer to Table 1.
Figure 1. MPC5500 Family Part Number Example
Unless noted in this data sheet, all specifications apply from TL to TH.
Table 1. Orderable Part Numbers
Freescale Part
Number1
Speed (MHz)
Package Description
MPC5565MVZ132
MPC5565MVZ112
MPC5565 324 package
Lead-free (PbFree)
MPC5565MVZ80
MPC5565MZQ132
MPC5565MZQ112
MPC5565MZQ80
Operating Temperature 2
MPC5565 324 package
Leaded (SnPb)
Nominal
Max. 3 (fMAX)
132
135
112
114
80
82
132
135
112
114
80
82
Min. (TL)
Max. (TH)
–40° C
125° C
–40° C
125° C
1
All devices are PPC5565, rather than MPC5565 or SPC5565, until product qualifications are complete. Not all configurations are
available in the PPC parts.
2 The lowest ambient operating temperature is referenced by T ; the highest ambient operating temperature is referenced by T .
L
H
3 Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed including frequency modulation (FM).
82 MHz parts allow for 80 MHz system clock + 2% FM; 114 MHz parts allow for 112 MHz system clock + 2% FM; and
135 MHz parts allow for 132 MHz system clock + 2% FM.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
3
Electrical Characteristics
3
Electrical Characteristics
This section contains detailed information on power considerations, DC/AC electrical characteristics, and
AC timing specifications for the MCU.
3.1
Maximum Ratings
Table 2. Absolute Maximum Ratings 1
Spec
Characteristic
Symbol
Min.
Max.
Unit
1
1.5 V core supply voltage 2
VDD
–0.3
1.7
V
2
Flash program/erase voltage
VPP
–0.3
6.5
V
4
Flash read voltage
VFLASH
–0.3
4.6
V
5
SRAM standby voltage
VSTBY
–0.3
1.7
V
6
Clock synthesizer voltage
VDDSYN
–0.3
4.6
V
7
3.3 V I/O buffer voltage
VDD33
–0.3
4.6
V
8
Voltage regulator control input voltage
VRC33
–0.3
4.6
V
9
Analog supply voltage (reference to VSSA)
VDDA
–0.3
5.5
V
VDDE
–0.3
4.6
V
VDDEH
–0.3
6.5
V
–1.0 5
–1.0 5
6.5 6
4.6 7
V
10
11
12
I/O supply voltage (fast I/O pads)
3
I/O supply voltage (slow and medium I/O pads)
3
4
DC input voltage
VDDEH powered I/O pads
VDDE powered I/O pads
VIN
13
Analog reference high voltage (reference to VRL)
VRH
–0.3
5.5
V
14
VSS to VSSA differential voltage
VSS – VSSA
–0.1
0.1
V
15
VDD to VDDA differential voltage
VDD – VDDA
–VDDA
VDD
V
16
VREF differential voltage
VRH – VRL
–0.3
5.5
V
17
VRH to VDDA differential voltage
VRH – VDDA
–5.5
5.5
V
18
VRL to VSSA differential voltage
VRL – VSSA
–0.3
0.3
V
19
VDDEH to VDDA differential voltage
VDDEH – VDDA
–VDDA
VDDEH
V
20
VDDF to VDD differential voltage
VDDF – VDD
–0.3
0.3
V
21
VRC33 to VDDSYN differential voltage spec has been moved to Table 9 DC Electrical Specifications, Spec 43a.
22
VSSSYN to VSS differential voltage
VSSSYN – VSS
–0.1
0.1
V
23
VRCVSS to VSS differential voltage
VRCVSS – VSS
–0.1
0.1
V
24
Maximum DC digital input current 8
(per pin, applies to all digital pins) 4
IMAXD
–2
2
mA
25
Maximum DC analog input current 9
(per pin, applies to all analog pins)
IMAXA
–3
3
mA
26
Maximum operating temperature range 10
Die junction temperature
TJ
TL
150.0
oC
27
Storage temperature range
TSTG
–55.0
150.0
oC
MPC5565 Microcontroller Data Sheet, Rev. 2.0
4
Freescale Semiconductor
Electrical Characteristics
Table 2. Absolute Maximum Ratings 1 (continued)
Spec
28
29
Characteristic
Symbol
Min.
Max.
Maximum solder temperature 11
Lead free (Pb-free)
Leaded (SnPb)
TSDR
—
—
260.0
245.0
Moisture sensitivity level 12
MSL
—
3
Unit
o
C
1
Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,
and functional operation at the maxima is not guaranteed. Stress beyond any of the listed maxima can affect device reliability
or cause permanent damage to the device.
2
1.5 V ± 10% for proper operation. This parameter is specified at a maximum junction temperature of 150 oC.
3
All functional non-supply I/O pins are clamped to VSS and VDDE, or VDDEH.
4
AC signal overshoot and undershoot of up to ± 2.0 V of the input voltages is permitted for an accumulative duration of
60 hours over the complete lifetime of the device (injection current not limited for this duration).
5
Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC
voltage greater than –0.6 V on SINB during the internal power-on reset (POR) state.
6 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDEH supplies, if the
maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications.
7 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V
DDE supplies, if the maximum
injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications.
8 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.
9 Total injection current for all analog input pins must not exceed 15 mA.
10 Lifetime operation at these specification limits is not guaranteed.
11 Moisture sensitivity profile per IPC/JEDEC J-STD-020D.
12 Moisture sensitivity per JEDEC test method A112.
3.2
Thermal Characteristics
The shaded rows in the following table indicate information specific to a four-layer board.
Table 3. MPC5565 Thermal Characteristics
Spec
5
6
natural convection (one-layer board)
RθJA
29
°C/W
natural convection (four-layer board 2s2p)
RθJA
19
°C/W
Junction to ambient (@200 ft./min., one-layer board)
RθJMA
23
°C/W
Junction to ambient (@200 ft./min., four-layer board 2s2p)
RθJMA
16
°C/W
RθJB
10
°C/W
RθJC
7
°C/W
ΨJT
2
°C/W
Junction to ambient
3
4
7
4
Unit
2
6
3
324 PBGA
1, 3,
5
2
Symbol
Junction to ambient
1
1
MPC5565 Thermal Characteristic
1, 2,
Junction to board
Junction to case
4
(four-layer board 2s2p)
5
6
Junction to package top , natural convection
Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.
Per JEDEC JESD51-6 with the board horizontal.
Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method
(MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature.
Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
5
Electrical Characteristics
3.2.1
General Notes for Specifications at Maximum Junction Temperature
An estimation of the device junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RθJA × PD)
where:
TA = ambient temperature for the package (oC)
RθJA = junction to ambient thermal resistance (oC/W)
PD = power dissipation in the package (W)
The thermal resistance values used are based on the JEDEC JESD51 series of standards to provide
consistent values for estimations and comparisons. The difference between the values determined for the
single-layer (1s) board compared to a four-layer board that has two signal layers, a power and a ground
plane (2s2p), demonstrate that the effective thermal resistance is not a constant. The thermal resistance
depends on the:
• Construction of the application board (number of planes)
• Effective size of the board which cools the component
• Quality of the thermal and electrical connections to the planes
• Power dissipated by adjacent components
Connect all the ground and power balls to the respective planes with one via per ball. Using fewer vias to
connect the package to the planes reduces the thermal performance. Thinner planes also reduce the thermal
performance. When the clearance between the vias leave the planes virtually disconnected, the thermal
performance is also greatly reduced.
As a general rule, the value obtained on a single-layer board is within the normal range for the tightly
packed printed circuit board. The value obtained on a board with the internal planes is usually within the
normal range if the application board has:
• One oz. (35 micron nominal thickness) internal planes
• Components are well separated
• Overall power dissipation on the board is less than 0.02 W/cm2
The thermal performance of any component depends on the power dissipation of the surrounding
components. In addition, the ambient temperature varies widely within the application. For many natural
convection and especially closed box applications, the board temperature at the perimeter (edge) of the
package is approximately the same as the local air temperature near the device. Specifying the local
ambient conditions explicitly as the board temperature provides a more precise description of the local
ambient conditions that determine the temperature of the device.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
6
Freescale Semiconductor
Electrical Characteristics
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TB + (RθJB × PD)
where:
TJ = junction temperature (oC)
TB = board temperature at the package perimeter (oC/W)
RθJB = junction-to-board thermal resistance (oC/W) per JESD51-8
PD = power dissipation in the package (W)
When the heat loss from the package case to the air does not factor into the calculation, an acceptable value
for the junction temperature is predictable. Ensure the application board is similar to the thermal test
condition, with the component soldered to a board with internal planes.
The thermal resistance is expressed as the sum of a junction-to-case thermal resistance plus a
case-to-ambient thermal resistance:
RθJA = RθJC + RθCA
where:
RθJA = junction-to-ambient thermal resistance (oC/W)
RθJC = junction-to-case thermal resistance (oC/W)
RθCA = case-to-ambient thermal resistance (oC/W)
RθJC is device related and is not affected by other factors. The thermal environment can be controlled to
change the case-to-ambient thermal resistance, RθCA. For example, change the air flow around the device,
add a heat sink, change the mounting arrangement on the printed circuit board, or change the thermal
dissipation on the printed circuit board surrounding the device. This description is most useful for
packages with heat sinks where 90% of the heat flow is through the case to heat sink to ambient.
For most packages, a better model is required.
A more accurate two-resistor thermal model can be constructed from the junction-to-board thermal
resistance and the junction-to-case thermal resistance. The junction-to-case thermal resistance describes
when using a heat sink or where a substantial amount of heat is dissipated from the top of the package. The
junction-to-board thermal resistance describes the thermal performance when most of the heat is
conducted to the printed circuit board. This model can be used to generate simple estimations and for
computational fluid dynamics (CFD) thermal models.
To determine the junction temperature of the device in the application on a prototype board, use the
thermal characterization parameter (ΨJT) to determine the junction temperature by measuring the
temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
TT = thermocouple temperature on top of the package (oC)
ΨJT = thermal characterization parameter (oC/W)
PD = power dissipation in the package (W)
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
7
Electrical Characteristics
The thermal characterization parameter is measured in compliance with the JESD51-2 specification using
a 40-gauge type T thermocouple epoxied to the top center of the package case. Position the thermocouple
so that the thermocouple junction rests on the package. Place a small amount of epoxy on the thermocouple
junction and approximately 1 mm of wire extending from the junction. Place the thermocouple wire flat
against the package case to avoid measurement errors caused by the cooling effects of the thermocouple
wire.
References:
Semiconductor Equipment and Materials International
3081 Zanker Rd.
San Jose, CA., 95134
(408) 943-6900
MIL-SPEC and EIA/JESD (JEDEC) specifications are available from Global Engineering Documents at
800-854-7179 or 303-397-7956.
JEDEC specifications are available on the web at http://www.jedec.org.
1. C.E. Triplett and B. Joiner, “An Experimental Characterization of a 272 PBGA Within an Automotive
Engine Controller Module,” Proceedings of SemiTherm, San Diego, 1998, pp. 47–54.
2. G. Kromann, S. Shidore, and S. Addison, “Thermal Modeling of a PBGA for Air-Cooled Applications,” Electronic Packaging and Production, pp. 53–58, March 1998.
3. B. Joiner and V. Adams, “Measurement and Simulation of Junction to Board Thermal Resistance and
Its Application in Thermal Modeling,” Proceedings of SemiTherm, San Diego, 1999, pp. 212–220.
3.3
Package
The MPC5565 is available in packaged form. Read the package options in Section 2, “Ordering
Information.” Refer to Section 4, “Mechanicals,” for pinouts and package drawings.
3.4
EMI (Electromagnetic Interference) Characteristics
Table 4. EMI Testing Specifications 1
Spec
Characteristic
Minimum
Typical
Maximum
Unit
0.15
—
1000
MHz
1
Scan range
2
Operating frequency
—
—
fMAX
MHz
3
VDD operating voltages
—
1.5
—
V
4
VDDSYN, VRC33, VDD33, VFLASH, VDDE operating voltages
—
3.3
—
V
5
VPP, VDDEH, VDDA operating voltages
—
5.0
—
V
2
6
Maximum amplitude
—
—
14
32 3
dBuV
7
Operating temperature
—
—
25
oC
1
EMI testing and I/O port waveforms per SAE J1752/3 issued 1995-03. Qualification testing was performed on the MPC5554
and applied to the MPC5500 family as generic EMI performance data.
2 Measured with the single-chip EMI program.
3 Measured with the expanded EMI program.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
8
Freescale Semiconductor
Electrical Characteristics
3.5
ESD (Electromagnetic Static Discharge) Characteristics
Table 5. ESD Ratings 1, 2
Characteristic
Symbol
Value
Unit
2000
V
R1
1500
Ω
C
100
pF
ESD for human body model (HBM)
HBM circuit description
500 (all pins)
ESD for field induced charge model (FDCM)
V
750 (corner pins)
Number of pulses per pin:
Positive pulses (HBM)
Negative pulses (HBM)
—
—
1
1
—
—
Interval of pulses
—
1
second
1
2
All ESD testing conforms to CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits.
Device failure is defined as: ‘If after exposure to ESD pulses, the device does not meet the device specification requirements,
which includes the complete DC parametric and functional testing at room temperature and hot temperature.
3.6
Voltage Regulator Controller (VRC) and
Power-On Reset (POR) Electrical Specifications
The following table lists the VRC and POR electrical specifications:
Table 6. VRC and POR Electrical Specifications
Spec
1
Characteristic
3.3 V (VDDSYN) POR
3
RESET pin supply
(VDDEH6) POR 1, 2
1
VRC33 voltage
6
Current can be sourced
7
Max.
Units
VPOR15
1.1
1.1
1.35
1.35
V
Asserted (ramp up)
Negated (ramp up)
Asserted (ramp down)
Negated (ramp down)
VPOR33
0.0
2.0
2.0
0.0
0.30
2.85
2.85
0.30
V
Negated (ramp up)
Asserted (ramp down)
VPOR5
2.0
2.0
2.85
2.85
V
VTRANS_START
1.0
2.0
V
When VRC allows the pass
transistor to completely turn on 3, 4
VTRANS_ON
2.0
2.85
V
When the voltage is greater than
the voltage at which the VRC keeps
the 1.5 V supply in regulation 5, 6
VVRC33REG
3.0
—
V
11.0
—
mA
9.0
—
mA
7.5
—
mA
—
1.0
V
Before VRC allows the pass
transistor to start turning on
4
5
Min.
Negated (ramp up)
Asserted (ramp down)
1.5 V (VDD) POR 1
2
Symbol
by VRCCTL at Tj:
– 40o C
o
25 C
150o
8
IVRCCTL
7
C
Voltage differential during power up such that:
VDD33 can lag VDDSYN or VDDEH6 before VDDSYN and VDDEH6 reach the
VPOR33 and VPOR5 minimums respectively.
VDD33_LAG
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
9
Electrical Characteristics
Table 6. VRC and POR Electrical Specifications (continued)
Spec
9
Characteristic
Symbol
Min.
Max.
Units
—
—
50
V/ms
40
—
—
45
—
—
55
500
—
Absolute value of slew rate on power supply pins
o
10
Required gain at Tj:
– 40 C
IDD ÷ IVRCCTL (@ fsys = fMAX) 6, 7, 8, 9
25o C
10
BETA
o
150 C
1
The internal POR signals are VPOR15, VPOR33, and VPOR5. On power up, assert RESET before the internal POR negates.
RESET must remain asserted until the power supplies are within the operating conditions as specified in Table 9 DC Electrical
Specifications. On power down, assert RESET before any power supplies fall outside the operating conditions and until the
internal POR asserts.
2
VIL_S (Table 9, Spec15) is guaranteed to scale with VDDEH6 down to VPOR5.
3
Supply full operating current for the 1.5 V supply when the 3.3 V supply reaches this range.
4
It is possible to reach the current limit during ramp up—do not treat this event as short circuit current.
5
At peak current for device.
6 Requires compliance with Freescale’s recommended board requirements and transistor recommendations. Board signal
traces/routing from the VRCCTL package signal to the base of the external pass transistor and between the emitter of the pass
transistor to the VDD package signals must have a maximum of 100 nH inductance and minimal resistance
(less than 1 Ω). VRCCTL must have a nominal 1 μF phase compensation capacitor to ground. VDD must have a 20 μF (nominal)
bulk capacitor (greater than 4 μF over all conditions, including lifetime). Place high-frequency bypass capacitors consisting of
eight 0.01 μF, two 0.1 μF, and one 1 μF capacitors around the package on the VDD supply signals.
7 I
VRCCTL is measured at the following conditions: VDD = 1.35 V, VRC33 = 3.1 V, VVRCCTL = 2.2 V.
8 Refer to Table 1 for the maximum operating frequency.
9 Values are based on I
DD from high-use applications as explained in the IDD Electrical Specification.
10 BETA is the worst-case external transistor BETA. It is measured on a per-part basis and calculated as (I
DD ÷ IVRCCTL).
3.7
Power-Up/Down Sequencing
Power sequencing between the 1.5 V power supply and VDDSYN or the RESET power supplies is required
if using an external 1.5 V power supply with VRC33 tied to ground (GND). To avoid power-sequencing,
VRC33 must be powered up within the specified operating range, even if the on-chip voltage regulator
controller is not used. Refer to Section 3.7.2, “Power-Up Sequence (VRC33 Grounded),” and
Section 3.7.3, “Power-Down Sequence (VRC33 Grounded).”
Power sequencing requires that VDD33 must reach a certain voltage where the values are read as ones
before the POR signal negates. Refer to Section 3.7.1, “Input Value of Pins During POR Dependent on
VDD33.”
Although power sequencing is not required between VRC33 and VDDSYN during power up, VRC33 must
not lead VDDSYN by more than 600 mV or lag by more than 100 mV for the VRC stage turn-on to operate
within specification. Higher spikes in the emitter current of the pass transistor occur if VRC33 leads or lags
VDDSYN by more than these amounts. The value of that higher spike in current depends on the board power
supply circuitry and the amount of board level capacitance.
Furthermore, when all of the PORs negate, the system clock starts to toggle, adding another large increase
of the current consumed by VRC33. If VRC33 lags VDDSYN by more than 100 mV, the increase in current
consumed can drop VDD low enough to assert the 1.5 V POR again. Oscillations are possible when the
1.5 V POR asserts and stops the system clock, causing the voltage on VDD to rise until the 1.5 V POR
negates again. All oscillations stop when VRC33 is powered sufficiently.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
10
Freescale Semiconductor
Electrical Characteristics
When powering down, VRC33 and VDDSYN have no delta requirement to each other, because the bypass
capacitors internal and external to the device are already charged. When not powering up or down, no delta
between VRC33 and VDDSYN is required for the VRC to operate within specification.
There are no power up/down sequencing requirements to prevent issues such as latch-up, excessive current
spikes, and so on. Therefore, the state of the I/O pins during power up and power down varies depending
on which supplies are powered.
Table 7 gives the pin state for the sequence cases for all pins with pad type pad_fc (fast type).
Table 7. Pin Status for Fast Pads During the Power Sequence
VDDE
VDD33
VDD
POR
Pin Status for Fast Pad Output Driver
pad_fc (fast)
Low
—
—
Asserted
Low
VDDE
Low
Low
Asserted
High
VDDE
Low
VDD
Asserted
High
VDDE
VDD33
Low
Asserted
High impedance (Hi-Z)
VDDE
VDD33
VDD
Asserted
Hi-Z
VDDE
VDD33
VDD
Negated
Functional
Table 8 gives the pin state for the sequence cases for all pins with pad type pad_mh (medium type) and
pad_sh (slow type).
Table 8. Pin Status for Medium and Slow Pads During the Power Sequence
VDDEH
VDD
POR
Pin Status for Medium and Slow Pad Output Driver
pad_mh (medium) pad_sh (slow)
Low
—
Asserted
Low
VDDEH
Low
Asserted
High impedance (Hi-Z)
VDDEH
VDD
Asserted
Hi-Z
VDDEH
VDD
Negated
Functional
The values in Table 7 and Table 8 do not include the effect of the weak-pull devices on the output pins
during power up.
Before exiting the internal POR state, the pins go to a high-impedance state until POR negates. When the
internal POR negates, the functional state of the signal during reset applies and the weak-pull devices
(up or down) are enabled as defined in the device reference manual. If VDD is too low to correctly
propagate the logic signals, the weak-pull devices can pull the signals to VDDE and VDDEH.
To avoid this condition, minimize the ramp time of the VDD supply to a time period less than the time
required to enable the external circuitry connected to the device outputs.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
11
Electrical Characteristics
3.7.1
Input Value of Pins During POR Dependent on VDD33
When powering up the device, VDD33 must not lag the latest VDDSYN or RESET power pin (VDDEH6) by
more than the VDD33 lag specification listed in Table 6, spec 8. This avoids accidentally selecting the
bypass clock mode because the internal versions of PLLCFG[0:1] and RSTCFG are not powered and
therefore cannot read the default state when POR negates. VDD33 can lag VDDSYN or the RESET power
pin (VDDEH6), but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification
applies during power up only. VDD33 has no lead or lag requirements when powering down.
3.7.2
Power-Up Sequence (VRC33 Grounded)
The 1.5 V VDD power supply must rise to 1.35 V before the 3.3 V VDDSYN power supply and the RESET
power supply rises above 2.0 V. This ensures that digital logic in the PLL for the 1.5 V power supply does
not begin to operate below the specified operation range lower limit of 1.35 V. Because the internal 1.5 V
POR is disabled, the internal 3.3 V POR or the RESET power POR must hold the device in reset. Since
they can negate as low as 2.0 V, VDD must be within specification before the 3.3 V POR and the RESET
POR negate.
VDDSYN and RESET Power
VDD
2.0 V
1.35 V
VDD must reach 1.35 V before VDDSYN and the RESET power reach 2.0 V
Figure 2. Power-Up Sequence (VRC33 Grounded)
3.7.3
Power-Down Sequence (VRC33 Grounded)
The only requirement for the power-down sequence with VRC33 grounded is if VDD decreases to less than
its operating range, VDDSYN or the RESET power must decrease to less than 2.0 V before the VDD power
increases to its operating range. This ensures that the digital 1.5 V logic, which is reset only by an ORed
POR and can cause the 1.5 V supply to decrease less than its specification value, resets correctly. See
Table 6, footnote 1.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
12
Freescale Semiconductor
Electrical Characteristics
3.8
DC Electrical Specifications
Table 9. DC Electrical Specifications (TA = TL to TH)
Spec
1
Characteristic
Core supply voltage (average DC RMS voltage)
1
Symbol
Min
Max.
Unit
VDD
1.35
1.65
V
VDDE
1.62
3.6
V
2
Input/output supply voltage (fast input/output)
3
Input/output supply voltage (slow and medium input/output)
VDDEH
3.0
5.25
V
4
3.3 V input/output buffer voltage
VDD33
3.0
3.6
V
5
Voltage regulator control input voltage
VRC33
3.0
3.6
V
VDDA
4.5
5.25
V
VPP
4.5
5.25
V
2
6
Analog supply voltage
8
Flash programming voltage 3
9
Flash read voltage
VFLASH
3.0
3.6
V
10
SRAM standby voltage 4
VSTBY
0.8
1.2
V
11
Clock synthesizer operating voltage
VDDSYN
3.0
3.6
V
12
Fast I/O input high voltage
VIH_F
0.65 × VDDE
VDDE + 0.3
V
13
Fast I/O input low voltage
VIL_F
VSS – 0.3
0.35 × VDDE
V
14
Medium and slow I/O input high voltage
VIH_S
0.65 × VDDEH
VDDEH + 0.3
V
15
Medium and slow I/O input low voltage
VIL_S
VSS – 0.3
0.35 × VDDEH
V
16
Fast input hysteresis
VHYS_F
0.1 × VDDE
V
17
Medium and slow I/O input hysteresis
VHYS_S
0.1 × VDDEH
V
18
Analog input voltage
VINDC
VSSA – 0.3
VDDA + 0.3
V
19
Fast output high voltage ( IOH_F = –2.0 mA )
VOH_F
0.8 × VDDE
—
V
20
Slow and medium output high voltage
IOH_S = –2.0 mA
IOH_S = –1.0 mA
VOH_S
0.80 × VDDEH
0.85 × VDDEH
—
V
21
Fast output low voltage ( IOL_F = 2.0 mA )
VOL_F
—
0.2 × VDDE
V
22
Slow and medium output low voltage
IOL_S = 2.0 mA
IOL_S = 1.0 mA
VOL_S
—
Load capacitance (fast I/O) 5
DSC (SIU_PCR[8:9] ) = 0b00
= 0b01
= 0b10
= 0b11
CL
24
Input capacitance (digital pins)
25
26
23
V
0.20 × VDDEH
0.15 × VDDEH
—
—
—
—
10
20
30
50
pF
pF
pF
pF
CIN
—
7
pF
Input capacitance (analog pins)
CIN_A
—
10
pF
Input capacitance:
(Shared digital and analog pins AN[12]_MA[0]_SDS,
AN[13]_MA[1]_SDO, AN[14]_MA[2]_SDI, and AN[15]_FCK)
CIN_M
—
12
pF
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
13
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL to TH) (continued)
Spec
Characteristic
Symbol
Min
Max.
Unit
IDD
IDD
IDD
IDD
—
—
—
—
46010
36010
51010
41010
mA
mA
mA
mA
IDD
IDD
IDD
IDD
—
—
—
—
41010
31010
46010
37010
mA
mA
mA
mA
IDD
IDD
IDD
IDD
—
—
—
—
33010
22510
38510
29010
mA
mA
mA
mA
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
20
30
50
μA
μA
μA
IDD_STBY @ 60o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
70
100
200
μA
μA
μA
IDD_STBY @ 150o C (Tj)
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
IDD_STBY
IDD_STBY
IDD_STBY
—
—
—
1200
1500
2000
μA
μA
μA
VDD33 12
IDD_33
—
2 + (values
derived from
procedure of
footnote 12)
mA
VFLASH
IVFLASH
—
10
mA
VDDSYN
IDDSYN
—
15
mA
IDD_A
IREF
IPP
—
—
—
20.0
1.0
25.0
mA
mA
mA
27a Operating current 1.5 V supplies @ 135 MHz: 6
VDD (including VDDF max current) @1.65 V typical use 7, 8
VDD (including VDDF max current) @1.35 V typical use 7, 8
VDD (including VDDF max current) @1.65 V high use 8, 9
VDD (including VDDF max current) @1.35 V high use 8, 9
27b Operating current 1.5 V supplies @ 114 MHz: 6
VDD (including VDDF max current)@1.65 V typical use 7, 8
VDD (including VDDF max current) @1.35 V typical use 7, 8
VDD (including VDDF max current) @1.65 V high use 8, 9
VDD (including VDDF max current) @1.35 V high use 8, 9
27c Operating current 1.5 V supplies @ 82 MHz: 6
VDD (including VDDF max current) @1.65 V typical use 7, 8
VDD (including VDDF max current) @1.35 V typical use 7, 8
VDD (including VDDF max current) @1.65 V high use 8, 9
VDD (including VDDF max current) @1.35 V high use 8, 9
27d Refer to Figure 3 for an interpolation of this data.11
IDD_STBY @ 25o C
VSTBY @ 0.8 V
VSTBY @ 1.0 V
VSTBY @ 1.2 V
28
29
Operating current 3.3 V supplies @ fMAX MHz
Operating current 5.0 V supplies (12 MHz ADCLK):
VDDA (VDDA0 + VDDA1)
Analog reference supply current (VRH, VRL)
VPP
MPC5565 Microcontroller Data Sheet, Rev. 2.0
14
Freescale Semiconductor
Electrical Characteristics
Table 9. DC Electrical Specifications (TA = TL to TH) (continued)
Spec
30
31
Characteristic
Operating current VDDE supplies: 13
VDDEH1
VDDE2
VDDE3
VDDEH4
VDDE5
VDDEH6
VDDE7
VDDEH8
VDDEH9
I/O input leakage current 15
34
DC injection current (per pin)
Analog input current, channel off
16
35a Analog input current, shared analog / digital pins
(AN[12], AN[13], AN[14], AN[15])
1
Max.
Unit
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
IDD7
IDD8
IDD9
—
—
—
—
—
—
—
—
—
Refer to
Footnote 13
mA
mA
mA
mA
mA
mA
mA
mA
mA
10
20
20
110
130
170
μA
μA
μA
10
20
20
100
130
170
μA
μA
μA
IACT_S
10
20
150
170
μA
μA
IINACT_D
–2.5
2.5
μA
IIC
–2.0
2.0
mA
IINACT_A
–150
150
nA
IINACT_AD
–2.5
2.5
μA
VSS – VSSA
–100
100
mV
VRL
VSSA – 0.1
VSSA + 0.1
V
VRL – VSSA
–100
100
mV
VRH
VDDA – 0.1
VDDA + 0.1
V
VRH – VRL
4.5
5.25
V
IACT_F
Slow and medium I/O weak pullup/down current 14
3.0–3.6 V
4.5–5.5 V
33
35
Min
Fast I/O weak pullup current 14
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
Fast I/O weak pulldown current 14
1.62–1.98 V
2.25–2.75 V
3.00–3.60 V
32
Symbol
36
VSS to VSSA differential voltage 17
37
Analog reference low voltage
38
VRL differential voltage
39
Analog reference high voltage
40
VREF differential voltage
41
VSSSYN to VSS differential voltage
VSSSYN – VSS
–50
50
mV
42
VRCVSS to VSS differential voltage
VRCVSS – VSS
–50
50
mV
43
VDDF to VDD differential voltage
VDDF – VDD
–100
100
mV
43a VRC33 to VDDSYN differential voltage
VRC33 – VDDSYN
–0.1
0.1 18
V
VIDIFF
–2.5
2.5
V
TA = (TL to TH)
TL
TH
οC
—
—
50
V/ms
44
Analog input differential signal range (with common mode 2.5 V)
45
Operating temperature range, ambient (packaged)
46
Slew rate on power-supply pins
VDDE2 and VDDE3 are limited to 2.25–3.6 V only if SIU_ECCR[EBTS] = 0; VDDE2 and VDDE3 have a range of 1.6–3.6 V if
SIU_ECCR[EBTS] = 1.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
15
Electrical Characteristics
2
| VDDA0 – VDDA1 | must be < 0.1 V.
VPP can drop to 3.0 V during read operations.
4
If standby operation is not required, connect VSTBY to ground.
5
Applies to CLKOUT, external bus pins, and Nexus pins.
6 Maximum average RMS DC current.
7
Average current measured on automotive benchmark.
8
Peak currents can be higher on specialized code.
9
High use current measured while running optimized SPE assembly code with all code and data 100% locked in cache
(0% miss rate) with all channels of the eMIOS and eTPU running autonomously, plus the eDMA transferring data continuously from
SRAM to SRAM. Higher currents can occur if an “idle” loop that crosses cache lines is run from cache.
Design and write code to avoid this condition.
10
Final values listed in specs 27a –27c are based on characterization.
11
Figure 3 shows an illustration of the IDD_STBY values interpolated for these temperature values.
12
Power requirements for the VDD33 supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
segments. Refer to Table 11 for values to calculate the power dissipation for a specific operation.
13 Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to Table 10 for values to calculate power dissipation for specific operation. The
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
14 Absolute value of current, measured at V and V .
IL
IH
15 Weak pullup/down inactive. Measured at V
DDE = 3.6 V and VDDEH = 5.25 V. Applies to pad types: pad_fc, pad_sh, and pad_mh.
16 Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8 oC
to 12 oC, in the ambient temperature range of 50 oC to 125 oC. Applies to pad types: pad_a and pad_ae.
17 V
SSA refers to both VSSA0 and VSSA1. | VSSA0 – VSSA1 | must be < 0.1 V.
18 Up to 0.6 V during power up and power down.
3
MPC5565 Microcontroller Data Sheet, Rev. 2.0
16
Freescale Semiconductor
Electrical Characteristics
Figure 3 shows an approximate interpolation of the ISTBY worst-case specification to estimate values at
different voltages and temperatures. The vertical lines shown at 25 οC, 60 οC, and 150 οC in Figure 3 are
the actual IDD_STBY specifications (27d) listed in Table 9.
Istby vs. Junction Tem p
2000
1900
1800
1700
1600
1500
1400
1300
µA
uA
1200
1100
0.8V
1000
900
800
1.0V
1.2V
700
600
500
400
300
200
100
0
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
Tem p (C)
Figure 3. ISTBY Worst-case Specifications
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
17
Electrical Characteristics
3.8.1
I/O Pad Current Specifications
The power consumption of an I/O segment depends on the usage of the pins on a particular segment. The
power consumption is the sum of all output pin currents for a segment. The output pin current can be
calculated from Table 10 based on the voltage, frequency, and load on the pin. Use linear scaling to
calculate pin currents for voltage, frequency, and load parameters that fall outside the values given in
Table 10.
Table 10. I/O Pad Average DC Current (TA = TL to TH)1
Spec
Pad Type
Symbol
1
2
Frequency
(MHz)
Load2 (pF)
Voltage (V)
Drive Select /
Slew Rate
Control Setting
Current (mA)
25
50
5.25
11
8.0
10
50
5.25
01
3.2
2
50
5.25
00
0.7
4
2
200
5.25
00
2.4
5
50
50
5.25
11
17.3
3
6
Slow
IDRV_SH
20
50
5.25
01
6.5
3.33
50
5.25
00
1.1
8
3.33
200
5.25
00
3.9
9
66
10
3.6
00
2.8
10
66
20
3.6
01
5.2
11
66
30
3.6
10
8.5
12
66
50
3.6
11
11.0
13
66
10
1.98
00
1.6
14
66
20
1.98
01
2.9
15
66
30
1.98
10
4.2
16
66
50
1.98
11
6.7
17
56
10
3.6
00
2.4
18
56
20
3.6
01
4.4
19
56
30
3.6
10
7.2
7
20
Medium
IDRV_MH
56
50
3.6
11
9.3
56
10
1.98
00
1.3
22
56
20
1.98
01
2.5
23
56
30
1.98
10
3.5
24
56
50
1.98
11
5.7
25
40
10
3.6
00
1.7
26
40
20
3.6
01
3.1
27
40
30
3.6
10
5.1
21
Fast
IDRV_FC
28
40
50
3.6
11
6.6
29
40
10
1.98
00
1.0
30
40
20
1.98
01
1.8
31
40
30
1.98
10
2.5
32
40
50
1.98
11
4.0
1
These values are estimates from simulation and are not tested. Currents apply to output pins only.
2
All loads are lumped.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
18
Freescale Semiconductor
Electrical Characteristics
3.8.2
I/O Pad VDD33 Current Specifications
The power consumption of the VDD33 supply dependents on the usage of the pins on all I/O segments. The
power consumption is the sum of all input and output pin VDD33 currents for all I/O segments. The output
pin VDD33 current can be calculated from Table 11 based on the voltage, frequency, and load on all fast
(pad_fc) pins. The input pin VDD33 current can be calculated from Table 11 based on the voltage,
frequency, and load on all pad_sh and pad_mh pins. Use linear scaling to calculate pin currents for voltage,
frequency, and load parameters that fall outside the values given in Table 11.
Table 11. VDD33 Pad Average DC Current (TA = TL to TH) 1
Spec
Pad Type
Symbol
Frequency
(MHz)
Load 2
(pF)
VDD33
(V)
VDDE
(V)
Drive
Select
Current
(mA)
Inputs
1
Slow
I33_SH
66
0.5
3.6
5.5
NA
0.003
2
Medium
I33_MH
66
0.5
3.6
5.5
NA
0.003
3
66
10
3.6
3.6
00
0.35
4
66
20
3.6
3.6
01
0.53
5
66
30
3.6
3.6
10
0.62
Outputs
6
66
50
3.6
3.6
11
0.79
7
66
10
3.6
1.98
00
0.35
8
66
20
3.6
1.98
01
0.44
9
66
30
3.6
1.98
10
0.53
10
66
50
3.6
1.98
11
0.70
11
56
10
3.6
3.6
00
0.30
12
56
20
3.6
3.6
01
0.45
13
56
30
3.6
3.6
10
0.52
14
56
50
3.6
3.6
11
0.67
56
10
3.6
1.98
00
0.30
16
56
20
3.6
1.98
01
0.37
17
56
30
3.6
1.98
10
0.45
15
Fast
I33_FC
18
56
50
3.6
1.98
11
0.60
19
40
10
3.6
3.6
00
0.21
20
40
20
3.6
3.6
01
0.31
21
40
30
3.6
3.6
10
0.37
22
40
50
3.6
3.6
11
0.48
23
40
10
3.6
1.98
00
0.21
24
40
20
3.6
1.98
01
0.27
25
40
30
3.6
1.98
10
0.32
26
40
50
3.6
1.98
11
0.42
1
These values are estimated from simulation and not tested. Currents apply to output pins for the fast pads only and to input
pins for the slow and medium pads only.
2
All loads are lumped.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
19
Electrical Characteristics
3.9
Oscillator and FMPLL Electrical Characteristics
Table 12. FMPLL Electrical Specifications
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
1
PLL reference frequency range: 1
Crystal reference2
External reference2
Dual controller (1:1 mode)
fref_crystal
fref_ext
fref_1:1
8
8
24
20
20
fsys ÷ 2
2
System frequency 3
fsys
fICO(MIN) ÷ 2RFD
fMAX 4
MHz
3
System clock period
tCYC
—
1 ÷ fsys
ns
4
Loss of reference frequency 5
fLOR
100
1000
kHz
5
Self-clocked mode (SCM) frequency 6
fSCM
7.4
17.5
MHz
EXTAL input high voltage crystal mode 7
VIHEXT
VXTAL + 0.4 V
—
V
All other modes
[dual controller (1:1), bypass, external reference]
VIHEXT
(VDDE5 ÷ 2) + 0.4 V
—
V
EXTAL input low voltage crystal mode 8
VILEXT
—
VXTAL – 0.4 V
V
All other modes
[dual controller (1:1), bypass, external reference]
VILEXT
—
(VDDE5 ÷ 2) – 0.4 V
V
IXTAL
2
6
mA
6
7
Unit
MHz
8
XTAL current 9
9
Total on-chip stray capacitance on XTAL
CS_XTAL
—
1.5
pF
10
Total on-chip stray capacitance on EXTAL
CS_EXTAL
—
1.5
pF
11
Crystal manufacturer’s recommended capacitive
load
CL
Refer to crystal
specification
Refer to crystal
specification
pF
Discrete load capacitance to connect to EXTAL
CL_EXTAL
—
(2 × CL) – CS_EXTAL
– CPCB_EXTAL 10
pF
Discrete load capacitance to connect to XTAL
CL_XTAL
—
(2 × CL) – CS_XTAL
– CPCB_XTAL 10
pF
tlpll
—
750
μs
tskew
–2
2
ns
12
13
14
PLL lock time 11
15
Dual controller (1:1) clock skew
(between CLKOUT and EXTAL) 12, 13
16
Duty cycle of reference
tDC
40
60
%
17
Frequency unLOCK range
fUL
–4.0
4.0
% fSYS
18
Frequency LOCK range
fLCK
–2.0
2.0
% fSYS
MPC5565 Microcontroller Data Sheet, Rev. 2.0
20
Freescale Semiconductor
Electrical Characteristics
Table 12. FMPLL Electrical Specifications (continued)
(VDDSYN = 3.0–3.6 V; VSS = VSSSYN = 0.0 V; TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
CJITTER
19
CLKOUT period jitter, measured at fSYS max: 14, 15
Peak-to-peak jitter (clock edge to clock edge)
Long term jitter (averaged over a 2 ms interval)
20
Frequency modulation range limit 16
(do not exceed fsys maximum)
21
ICO frequency
fico = [ fref_crystal × (MFD + 4) ] ÷ (PREDIV + 1) 17
fico = [ fref_ext × (MFD + 4) ] ÷ (PREDIV + 1)
22
Predivider output frequency (to PLL)
Unit
—
—
5.0
0.01
CMOD
0.8
2.4
%fSYS
fico
48
fMAX
MHz
fPREDIV
4
20 18
MHz
%
fCLKOUT
1
Nominal crystal and external reference values are worst-case not more than 1%. The device operates correctly if the frequency
remains within ± 5% of the specification limit. This tolerance range allows for a slight frequency drift of the crystals over time.
The designer must thoroughly understand the drift margin of the source clock.
2 The 8–20 MHz crystal or external reference values have PLLCFG[2] pulled low. PLLCFG[2] is not supported pulled high.
3 All internal registers retain data at 0 Hz.
4 Up to the maximum frequency rating of the device (refer to Table 1).
5 Loss of reference frequency is defined as the reference frequency detected internally, which transitions the PLL into self-clocked
mode.
6 The PLL operates at self-clocked mode (SCM) frequency when the reference frequency falls below f
LOR. SCM frequency is
measured on the CLKOUT ball with the divider set to divide-by-two of the system clock.
NOTE: In SCM, the MFD and PREDIV have no effect and the RFD is bypassed.
7 Use the EXTAL input high voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vextal – Vxtal) must be ≥ 400 mV for the oscillator’s comparator to produce the output clock.
8 Use the EXTAL input low voltage parameter when using the FlexCAN oscillator in crystal mode (no quartz crystals or
resonators). (Vxtal – Vextal) must be ≥ 400 mV for the oscillator’s comparator to produce the output clock.
9 I
xtal is the oscillator bias current out of the XTAL pin with both EXTAL and XTAL pins grounded.
10 C
PCB_EXTAL and CPCB_XTAL are the measured PCB stray capacitances on EXTAL and XTAL, respectively.
11 This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR). From power up with crystal oscillator reference, the lock time also includes the crystal
startup time.
12 PLL is operating in 1:1 PLL mode.
13 V
DDE = 3.0–3.6 V.
14 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f .
sys
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via VDDSYN and VSSSYN and variation in crystal oscillator frequency increase the jitter percentage
for a given interval. CLKOUT divider is set to divide-by-two.
15 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of (jitter + Cmod).
16
Modulation depth selected must not result in fsys value greater than the fsys maximum specified value.
RFD).
sys = fico ÷ (2
17 f
18 Maximum
value for dual controller (1:1) mode is (fMAX ÷ 2) with the predivider set to 1 (FMPLL_SYNCR[PREDIV] = 0b001).
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
21
Electrical Characteristics
3.10
eQADC Electrical Characteristics
Table 13. eQADC Conversion Specifications (TA = TL to TH)
Spec
Characteristic
Symbol
Minimum
Maximum
Unit
FADCLK
1
12
MHz
13 + 2 (15)
14 + 2 (16)
13 + 128 (141)
14 + 128 (142)
1
ADC clock (ADCLK) frequency 1
Conversion cycles
Differential
Single ended
CC
2
3
Stop mode recovery time 2
TSR
10
—
μs
—
1.25
—
mV
3
ADCLK
cycles
4
Resolution
5
INL: 6 MHz ADC clock
INL6
–4
4
Counts 3
6
INL: 12 MHz ADC clock
INL12
–8
7
8
9
10
DNL: 6 MHz ADC clock
DNL: 12 MHz ADC clock
Offset error with calibration
Full-scale gain error with calibration
7, 8, 9, 10
8
Counts
DNL6
–3
4
34
Counts
DNL12
–6 4
6
4
Counts
OFFWC
–4 5
4
5
Counts
GAINWC
–8 6
8
6
Counts
IINJ
–1
1
mA
11
Disruptive input injection current
12
Incremental error due to injection current. All channels are
10 kΩ < Rs <100 kΩ
Channel under test has Rs = 10 kΩ,
IINJ = IINJMAX, IINJMIN
EINJ
–4
4
Counts
13
Total unadjusted error (TUE) for single ended conversions
with calibration 11, 12, 13, 14, 15
TUE
–4
4
Counts
1
Conversion characteristics vary with FADCLK rate. Reduced conversion accuracy occurs at maximum FADCLK rate. The
maximum value is based on 800 KS/s and the minimum value is based on 20 MHz oscillator clock frequency divided by a
maximum 16 factor.
2
Stop mode recovery time begins when the ADC control register enable bits are set until the ADC is ready to perform
conversions.
3 At V
RH – VRL = 5.12 V, one least significant bit (LSB) = 1.25, mV = one count.
4
Guaranteed 10-bit mono tonicity.
5 The absolute value of the offset error without calibration ≤ 100 counts.
6 The absolute value of the full scale gain error without calibration ≤ 120 counts.
7 Below disruptive current conditions, the channel being stressed has conversion values of: 0x3FF for analog inputs greater than
VRH, and 0x000 for values less than VRL. This assumes that VRH ≤ VDDA and VRL ≥ VSSA due to the presence of the sample
amplifier. Other channels are not affected by non-disruptive conditions.
8 Exceeding the limit can cause a conversion error on both stressed and unstressed channels. Transitions within the limit do not
affect device reliability or cause permanent damage.
9 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values using VPOSCLAMP = VDDA + 0.5 V and VNEGCLAMP = – 0.3 V, then use the larger of the calculated values.
10 This condition applies to two adjacent pads on the internal pad.
11 The TUE specification is always less than the sum of the INL, DNL, offset, and gain errors due to canceling errors.
12
TUE does not apply to differential conversions.
13 Measured at 6 MHz ADC clock. TUE with a 12 MHz ADC clock is: –16 counts < TUE < 16 counts.
14 TUE includes all internal device errors such as internal reference variation (75% Ref, 25% Ref).
15
Depending on the input impedance, the analog input leakage current (Table 9. DC Electrical Specifications, spec 35a) can
affect the actual TUE measured on analog channels AN[12], AN[13], AN[14], AN[15].
MPC5565 Microcontroller Data Sheet, Rev. 2.0
22
Freescale Semiconductor
Electrical Characteristics
3.11
H7Fa Flash Memory Electrical Characteristics
Table 14. Flash Program and Erase Specifications (TA = TL to TH)
Spec
3
1
2
3
4
5
6
Flash Program Characteristic
Doubleword (64 bits) program time 4
Symbol
Min.
Typical 1
Initial
Max. 2
Max. 3
Unit
Tdwprogram
—
10
—
500
μs
500
μs
4
Page program time
4
5
Tpprogram
—
22
44
7
16 KB block pre-program and erase time
T16kpperase
—
265
400
5000
ms
9
48 KB block pre-program and erase time
T48kpperase
—
345
400
5000
ms
10
64 KB block pre-program and erase time
T64kpperase
—
415
500
5000
ms
8
128 KB block pre-program and erase time
T128kpperase
—
500
1250
7500
ms
11
Minimum operating frequency for program and erase
operations 6
—
25
—
—
—
MHz
Typical program and erase times are calculated at 25 oC operating temperature using nominal supply values.
Initial factory condition: ≤ 100 program/erase cycles, 25 oC, using a typical supply voltage measured at a minimum system
frequency of 80 MHz.
The maximum erase time occurs after the specified number of program/erase cycles. This maximum value is characterized
but not guaranteed.
Actual hardware programming times. This does not include software overhead.
Page size is 256 bits (8 words).
The read frequency of the flash can range up to the maximum operating frequency. There is no minimum read frequency
condition.
Table 15. Flash EEPROM Module Life (TA = TL to TH)
Spec
1
Characteristic
Symbol
Min.
Typical 1
Unit
1a
Number of program/erase cycles per block for 16 KB, 48 KB, and
64 KB blocks over the operating temperature range (TJ)
P/E
100,000
—
cycles
1b
Number of program/erase cycles per block for 128 KB blocks over the
operating temperature range (TJ)
P/E
1000
100,000
cycles
2
Data retention
Blocks with 0–1,000 P/E cycles
Blocks with 1,001–100,000 P/E cycles
20
5
—
—
years
Retention
Typical endurance is evaluated at 25o C. Product qualification is performed to the minimum specification. For additional
information on the Freescale definition of typical endurance, refer to engineering bulletin EB619 Typical Endurance for
Nonvolatile Memory.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
23
Electrical Characteristics
Table 16 shows the FLASH_BIU settings versus frequency of operation. Refer to the device reference
manual for definitions of these bit fields.
Table 16. FLASH_BIU Settings vs. Frequency of Operation 1
Maximum Frequency (MHz)
DPFEN 2
IPFEN 2
PFLIM 3
BFEN 4
0b01
0b00
0b01
0b11
0b00
0b01
0b11
0b000
to
0b110
0b0
0b1
0b010
0b01
0b00
0b01
0b11
0b00
0b01
0b11
0b000
to
0b110
0b0
0b1
0b010
0b011
0b01
0b00
0b01
0b11
0b00
0b01
0b11
0b000
to
0b110
0b0
0b1
0b111
0b111
0b11
0b00
0b00
0b000
0b0
APC
RWSC
WWSC
Up to and including 82 MHz 5
0b001
0b001
Up to and including 102 MHz 6
0b001
Up to and including 135 MHz 7
Default setting after reset
1
2
3
4
5
6
7
Illegal combinations exist. Use entries from the same row in this table.
For maximum flash performance, set to 0b11.
For maximum flash performance, set to 0b110.
For maximum flash performance, set to 0b1.
82 MHz parts allow for 80 MHz system clock + 2% frequency modulation (FM).
102 MHz parts allow for 100 MHz system clock + 2% FM.
135 MHz parts allow for 132 MHz system clock + 2% FM.
3.12
3.12.1
AC Specifications
Pad AC Specifications
Table 17. Pad AC Specifications (VDDEH = 5.0 V, VDDE = 1.8 V) 1
Spec
SRC / DSC
(binary)
Pad
11
1
Slow high voltage (SH)
01
00
11
2
Medium high voltage (MH)
01
00
Out Delay 2, 3, 4
(ns)
Rise / Fall 4, 5
(ns)
Load Drive
(pF)
26
15
50
82
60
200
75
40
50
137
80
200
377
200
50
476
260
200
16
8
50
43
30
200
34
15
50
61
35
200
192
100
50
239
125
200
MPC5565 Microcontroller Data Sheet, Rev. 2.0
24
Freescale Semiconductor
Electrical Characteristics
Table 17. Pad AC Specifications (VDDEH = 5.0 V, VDDE = 1.8 V) 1 (continued)
Spec
Out Delay 2, 3, 4
(ns)
SRC / DSC
(binary)
Pad
Rise / Fall 4, 5
(ns)
Load Drive
(pF)
2.7
10
2.5
20
2.4
30
2.3
50
00
3
01
Fast
3.1
10
11
1
2
3
4
5
4
Pullup/down (3.6 V max)
—
—
7500
50
5
Pullup/down (5.5 V max)
—
—
9000
50
These are worst-case values that are estimated from simulation (not tested). The values in the table are simulated at:
VDD = 1.35–1.65 V; VDDE = 1.62–1.98 V; VDDEH = 4.5–5.25 V; VDD33 and VDDSYN = 3.0–3.6 V; and TA = TL to TH.
This parameter is supplied for reference and is guaranteed by design (not tested).
The output delay is shown in Figure 4. To calculate the output delay with respect to the system clock,
add a maximum of one system clock to the output delay.
The output delay and rise and fall are measured to 20% or 80% of the respective signal.
This parameter is guaranteed by characterization rather than 100% tested.
Table 18. Derated Pad AC Specifications (VDDEH = 3.3 V, VDDE = 3.3 V) 1
Spec
SRC/DSC
(binary)
Pad
11
1
Slow high voltage (SH)
01
00
11
2
Medium high voltage (MH)
01
00
Out Delay 2, 3, 4
(ns)
Rise / Fall 3, 5
(ns)
Load Drive
(pF)
39
23
50
120
87
200
101
52
50
188
111
200
507
248
50
597
312
200
23
12
50
64
44
200
50
22
50
90
50
200
261
123
50
305
156
200
2.4
10
2.2
20
2.1
30
2.1
50
00
3
01
Fast
10
3.2
11
4
Pullup/down (3.6 V max)
—
—
7500
50
5
Pullup/down (5.5 V max)
—
—
9500
50
1
These are worst-case values that are estimated from simulation (not tested). The values in the table are simulated at:
VDD = 1.35–1.65 V; VDDE = 3.0–3.6 V; VDDEH = 3.0–3.6 V; VDD33 and VDDSYN = 3.0–3.6 V; and TA = TL to TH.
2 This parameter is supplied for reference and guaranteed by design (not tested).
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
25
Electrical Characteristics
3
The output delay, and the rise and fall, are calculated to 20% or 80% of the respective signal.
The output delay is shown in Figure 4. To calculate the output delay with respect to the system clock, add a maximum of one
system clock to the output delay.
5
This parameter is guaranteed by characterization rather than 100% tested.
4
VDD ÷ 2
Pad
internal data
input signal
Rising-edge
out delay
Falling-edge
out delay
VOH
Pad
output
VOL
Figure 4. Pad Output Delay
3.13
AC Timing
3.13.1
Reset and Configuration Pin Timing
Table 19. Reset and Configuration Pin Timing 1
Spec
1
Characteristic
Symbol
Min.
Max.
Unit
1
RESET pulse width
tRPW
10
—
tCYC
2
RESET glitch detect pulse width
tGPW
2
—
tCYC
3
PLLCFG, BOOTCFG, WKPCFG, RSTCFG setup time to RSTOUT valid
tRCSU
10
—
tCYC
4
PLLCFG, BOOTCFG, WKPCFG, RSTCFG hold time from RSTOUT valid
tRCH
0
—
tCYC
Reset timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
26
Freescale Semiconductor
Electrical Characteristics
2
RESET
1
RSTOUT
3
PLLCFG
BOOTCFG
RSTCFG
WKPCFG
4
Figure 5. Reset and Configuration Pin Timing
3.13.2
IEEE 1149.1 Interface Timing
Table 20. JTAG Pin AC Electrical Characteristics 1
Spec
1
Characteristic
Symbol
Min.
Max.
Unit
1
TCK cycle time
tJCYC
100
—
ns
2
TCK clock pulse width (measured at VDDE ÷ 2)
tJDC
40
60
ns
3
TCK rise and fall times (40% to 70%)
tTCKRISE
—
3
ns
4
TMS, TDI data setup time
tTMSS, tTDIS
5
—
ns
5
TMS, TDI data hold time
tTMSH, tTDIH
25
—
ns
6
TCK low to TDO data valid
tTDOV
—
20
ns
7
TCK low to TDO data invalid
tTDOI
0
—
ns
8
TCK low to TDO high impedance
tTDOHZ
—
20
ns
9
JCOMP assertion time
tJCMPPW
100
—
ns
10
JCOMP setup time to TCK low
tJCMPS
40
—
ns
11
TCK falling-edge to output valid
tBSDV
—
50
ns
12
TCK falling-edge to output valid out of high impedance
tBSDVZ
—
50
ns
13
TCK falling-edge to output high impedance (Hi-Z)
tBSDHZ
—
50
ns
14
Boundary scan input valid to TCK rising-edge
tBSDST
50
—
ns
15
TCK rising-edge to boundary scan input invalid
tBSDHT
50
—
ns
These specifications apply to JTAG boundary scan only. JTAG timing specified at: VDDE = 3.0–3.6 V and TA = TL to TH.
Refer to Table 21 for Nexus specifications.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
27
Electrical Characteristics
TCK
2
3
2
1
3
Figure 6. JTAG Test Clock Input Timing
TCK
4
5
TMS, TDI
6
7
8
TDO
Figure 7. JTAG Test Access Port Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
28
Freescale Semiconductor
Electrical Characteristics
TCK
10
JCOMP
9
Figure 8. JTAG JCOMP Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
29
Electrical Characteristics
TCK
11
13
Output
signals
12
Output
signals
14
15
Input
signals
Figure 9. JTAG Boundary Scan Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
30
Freescale Semiconductor
Electrical Characteristics
3.13.3
Nexus Timing
Table 21. Nexus Debug Port Timing 1
Spec
Characteristic
1
MCKO cycle time
2
MCKO duty cycle
3
4
MCKO low to MDO data valid
3
MCKO low to MSEO data valid
3
3
Symbol
Min.
Max.
Unit
tMCYC
12
8
tCYC
tMDC
40
60
%
tMDOV
–1.5
3.0
ns
tMSEOV
–1.5
3.0
ns
tEVTOV
–1.5
3.0
ns
5
MCKO low to EVTO data valid
6
EVTI pulse width
tEVTIPW
4.0
—
tTCYC
7
EVTO pulse width
tEVTOPW
1
4
9
TCK duty cycle
tTDC
40
60
%
10
TDI, TMS data setup time
tNTDIS, tNTMSS
8
—
ns
11
TDI, TMS data hold time
tNTDIH, tNTMSH
5
—
ns
0
12
ns
0
10
ns
—
—
—
13
4
5
tCYC
tTCYC
tJOV
VDDE = 2.25–3.0 V
VDDE = 3.0–3.6 V
3
—
TCK cycle time
12
2
tMCYC
8
TCK low to TDO data valid
1
—
4
RDY valid to MCKO
5
—
JTAG specifications apply when used for debug functionality. All Nexus timing relative to MCKO is measured from 50% of
MCKO and 50% of the respective signal. Nexus timing specified at VDD = 1.35–1.65 V, VDDE = 2.25–3.6 V,
VDD33 and VDDSYN = 3.0–3.6 V, TA = TL to TH, and CL = 30 pF with DSC = 0b10.
The Nexus AUX port runs up to 82 MHz. Set NPC_PCR[MCKO_DIV] to divide-by-two if the system frequency
is greater than 82 MHz.
MDO, MSEO, and EVTO data is held valid until the next MCKO low cycle occurs.
Limit the maximum frequency to approximately 16 MHz (VDDE = 2.25–3.0 V) or 20 MHz (VDDE = 3.0–3.6 V) to meet the timing
specification for tJOV of [0.2 x tJCYC] as outlined in the IEEE-ISTO 5001-2003 specification.
The RDY pin timing is asynchronous to MCKO and is guaranteed by design to function correctly.
1
2
MCKO
4
3
5
MDO
MSEO
EVTO
Output Data Valid
Figure 10. Nexus Output Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
31
Electrical Characteristics
TCK
10
11
TMS, TDI
12
TDO
Figure 11. Nexus TDI, TMS, TDO Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
32
Freescale Semiconductor
Electrical Characteristics
3.13.4
External Bus Interface (EBI) Timing
Table 22 lists the timing information for the external bus interface (EBI).
Table 22. Bus Operation Timing1
Spec
Characteristic
and
Description
1
CLKOUT period
2
CLKOUT duty cycle
3
4
CLKOUT rise time
CLKOUT fall time
CLKOUT positive edge to output
signal invalid or Hi-Z (hold time)
External Bus Frequency 2, 3
Symbol
40 MHz
56 MHz
Unit
Notes
Signals are measured
at 50% VDDE.
Min.
Max.
Min.
Max.
Min.
Max.
TC
24.4
—
17.5
—
14.9
—
ns
tCDC
45%
55%
45%
55%
45%
55%
TC
tCRT
4
—
—
tCFT
—
—4
tCOH
1.08
4
—
—
—
—4
1.08
—
1.5
5
66 MHz
—
—
4
ns
—
—4
ns
—
ns
1.08
—
EBTS = 0
1.5
1.5
EBTS = 1
External bus interface
CS[0:3]
ADDR[8:31]
DATA[0:31] 5
BDIP
OE
RD_WR
TA
TEA 6
TS
WE/BE[0:3] 7
CLKOUT positive edge to output
signal invalid or Hi-Z (hold time)
Hold time selectable
via SIU_ECCR
[EBTS] bit.
tCCOH
1.08
1.08
—
1.5
1.08
—
1.5
EBTS = 0
—
1.5
Calibration bus interface
CAL_CS[0, 2:3]
CAL_ADDR[10:30]
CAL_DATA[0:15]
CAL_OE
CAL_RD_WR
CAL_TS
CAL_WE/BE[0:1]
ns
EBTS = 1
Hold time selectable
via SIU_ECCR
[EBTS] bit.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
33
Electrical Characteristics
Table 22. Bus Operation Timing1 (continued)
Spec
Characteristic
and
Description
CLKOUT positive edge to output
signal valid (output delay)
External Bus Frequency 2, 3
Symbol
40 MHz
Min.
Max.
56 MHz
Min.
10.08
tCOV
—
Unit
6.08
—
8.5
Notes
Max.
EBTS = 0
ns
7.0
EBTS = 1
External bus interface
CS[0:3]
ADDR[8:31]
DATA[0:31] 5
BDIP
OE
RD_WR
TA
TEA 6
TS
WE/BE[0:3] 7
CLKOUT positive edge to output
signal valid (output delay)
Output valid time
selectable via
SIU_ECCR
[EBTS] bit.
11.08
tCCOV
—
8.58
—
12.0
6a
Min.
7.58
—
11.0
6
Max.
66 MHz
7.08
ns
EBTS = 0
—
9.5
8.0
EBTS = 1
Calibration bus interface
CAL_CS[0, 2:3]
CAL_ADDR[10:30]
CAL_DATA[0:15]
CAL_OE
CAL_RD_WR
CAL_TS
CAL_WE/BE[0:1]
Output valid time
selectable via
SIU_ECCR
[EBTS] bit.
Input signal valid to CLKOUT
positive edge (setup time)
7
External bus interface
ADDR[8:31]
DATA[0:31] 5
RD_WR
TA
TEA 6
TS
tCIS
10.0
—
7.0
—
5.0
—
ns
tCCIS
11.0
—
8.0
—
6.0
—
ns
Input signal valid to CLKOUT
positive edge (setup time)
Calibration bus interface
CAL_ADDR[10:30]
CAL_DATA[0:15]
CAL_RD_WR
CAL_TS
MPC5565 Microcontroller Data Sheet, Rev. 2.0
34
Freescale Semiconductor
Electrical Characteristics
Table 22. Bus Operation Timing1 (continued)
Spec
Characteristic
and
Description
External Bus Frequency 2, 3
Symbol
40 MHz
56 MHz
Unit
66 MHz
Min.
Max.
Min.
Max.
Min.
Max.
tCIH
1.0
—
1.0
—
1.0
—
ns
tCCIH
1.0
—
1.0
—
1.0
—
ns
Notes
CLKOUT positive edge to input
signal invalid (hold time)
8
External bus interface
ADDR[8:31]
DATA[0:31] 5
RD_WR
TA
TEA 6
TS
CLKOUT positive edge to input
signal invalid (hold time)
Calibration bus interface
CAL_ADDR[10:30]
CAL_DATA[0:15]
CAL_RD_WR
CAL_TS
1
2
3
4
5
6
7
8
EBI timing specified at: VDDE = 1.6–3.6 V (unless stated otherwise); TA = TL to TH; and CL = 30 pF with DSC = 0b10.
Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed including frequency modulation (FM).
82 MHz parts allow for 80 MHz system clock + 2% FM; 114 MHz parts allow for 112 MHz system clock + 2% FM; and
135 MHz parts allow for 132 MHz system clock + 2% FM.
The external bus is limited to half the speed of the internal bus.
Refer to fast pad timing in Table 17 and Table 18 (different values for 1.8 V and 3.3 V).
Due to pin limitations, the DATA[16:31] signals are not available on the 324 package.
Due to pin limitations, the TEA signal is not available on the 324 package.
Due to pin limitations, the WE/BE[2:3] signals are not available on the 324 package.
SIU_ECCR[EBTS] = 0 timings are tested and valid at VDDE = 2.25–3.6 V only; SIU_ECCR[EBTS] = 1 timings are tested and
valid at VDDE = 1.6–3.6 V.
Voh_f
VDDE ÷ 2
CLKOUT
Vol_f
3
2
2
4
1
Figure 12. CLKOUT Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
35
Electrical Characteristics
VDDE ÷ 2
CLKOUT
6
5
VDDE ÷ 2
5
Output
bus
VDDE ÷ 2
6
5
5
Output
signal
VDDE ÷ 2
6
Output
signal
VDDE ÷ 2
Figure 13. Synchronous Output Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
36
Freescale Semiconductor
Electrical Characteristics
CLKOUT
VDDE ÷ 2
7
8
Input
bus
VDDE ÷ 2
7
8
Input
signal
VDDE ÷ 2
Figure 14. Synchronous Input Timing
3.13.5
External Interrupt Timing (IRQ Signals)
Table 23. External Interrupt Timing 1
Spec
1
2
Characteristic
Symbol
Min.
Max.
Unit
1
IRQ pulse-width low
tIPWL
3
—
tCYC
2
IRQ pulse-width high
TIPWH
3
—
tCYC
3
IRQ edge-to-edge time 2
tICYC
6
—
tCYC
IRQ timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
Applies when IRQ signals are configured for rising-edge or falling-edge events, but not both.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
37
Electrical Characteristics
IRQ
2
1
3
Figure 15. External Interrupt Timing
3.13.6
eTPU Timing
Table 24. eTPU Timing 1
Spec
1
2
1
2
Characteristic
eTPU input channel pulse width
eTPU output channel pulse width
Symbol
Min.
Max
Unit
tICPW
4
—
tCYC
—
tCYC
tOCPW
2
2
eTPU timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
This specification does not include the rise and fall times. When calculating the minimum eTPU pulse width, include the rise
and fall times defined in the slew rate control fields (SRC) of the pad configuration registers (PCR).
2
eTPU
output
eTPU input
and TCRCLK
1
Figure 16. eTPU Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
38
Freescale Semiconductor
Electrical Characteristics
3.13.7
eMIOS Timing
Table 25. eMIOS Timing 1
Spec
Characteristic
1
2
Min.
Max.
Unit
tMIPW
4
—
tCYC
—
tCYC
eMIOS input pulse width
2
1
Symbol
eMIOS output pulse width
tMOPW
1
2
eMIOS timing specified at: VDDEH = 3.0–5.25 V and TA = TL to TH.
This specification does not include the rise and fall times. When calculating the minimum eMIOS pulse width, include the rise
and fall times defined in the slew rate control field (SRC) in the pad configuration register (PCR).
2
eMIOS
output
eMIOS input
1
Figure 17. eMIOS Timing
3.13.8
DSPI Timing
Table 26. DSPI Timing1’ 2
80 MHz
Characteristic
Spec
1
2
3
SCK cycle time3, 4
PCS to SCK
After SCK
112 MHz
132 MHz
Symbol
delay5
delay6
Unit
Min.
Max.
Min.
Max.
Min.
Max.
tSCK
24.4 ns
2.9 ms
17.5 ns
2.1 ms
14.8 ns
1.8 ms
—
tCSC
23
—
15
—
13
—
ns
14
—
12
—
ns
tASC
22
—
tSDC
(tSCK ÷ 2)
– 2 ns
(tSCK ÷ 2)
+ 2 ns
tA
—
25
—
25
—
25
ns
tDIS
—
25
—
25
—
25
ns
(tSCK ÷ 2) (tSCK ÷ 2) (tSCK ÷ 2) (tSCK ÷ 2)
– 2 ns
+ 2 ns
– 2 ns
+ 2 ns
4
SCK duty cycle
5
Slave access time
(SS active to SOUT driven)
6
Slave SOUT disable time
(SS inactive to SOUT Hi-Z, or invalid)
7
PCSx to PCSS time
tPCSC
4
—
4
—
4
—
ns
8
PCSS to PCSx time
tPASC
5
—
5
—
5
—
ns
ns
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
39
Electrical Characteristics
Table 26. DSPI Timing1’ 2 (continued)
80 MHz
Spec
1
2
3
4
5
6
7
Characteristic
112 MHz
132 MHz
Symbol
tSUI
9
Data setup time for inputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)7
Master (MTFE = 1, CPHA = 1)
tHI
10
Data hold time for inputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)7
Master (MTFE = 1, CPHA = 1)
tSUO
11
Data valid (after SCK edge)
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)
Master (MTFE = 1, CPHA = 1)
tHO
12
Data hold time for outputs
Master (MTFE = 0)
Slave
Master (MTFE = 1, CPHA = 0)
Master (MTFE = 1, CPHA = 1)
Unit
Min.
Max.
Min.
Max.
Min.
Max.
20
2
–4
20
—
—
—
—
20
2
3
20
—
—
—
—
20
2
6
20
—
—
—
—
ns
ns
ns
ns
–4
7
21
–4
—
—
—
—
–4
7
14
–4
—
—
—
—
–4
7
12
–4
—
—
—
—
ns
ns
ns
ns
—
—
—
—
5
25
18
5
—
—
—
—
5
25
14
5
—
—
—
—
5
25
13
5
ns
ns
ns
ns
–5
5.5
8
–5
—
—
—
—
–5
5.5
4
–5
—
—
—
—
–5
5.5
3
–5
—
—
—
—
ns
ns
ns
ns
All DSPI timing specifications use the fastest slew rate (SRC = 0b11) on pad type M or MH. DSPI signals using pad types
of S or SH have an additional delay based on the slew rate. DSPI timing is specified at: VDDEH = 3.0–5.25 V;TA = TL to TH;
and CL = 50 pF with SRC = 0b11.
Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed including frequency modulation (FM).
82 MHz parts allow for 80 MHz system clock + 2% FM; 114 MHz parts allow for 112 MHz system clock + 2% FM; and
135 MHz parts allow for 132 MHz system clock + 2% FM.
The minimum SCK cycle time restricts the baud rate selection for the given system clock rate.
These numbers are calculated based on two MPC55xx devices communicating over a DSPI link.
The actual minimum SCK cycle time is limited by pad performance.
The maximum value is programmable in DSPI_CTARx[PSSCK] and DSPI_CTARx[CSSCK].
The maximum value is programmable in DSPI_CTARx[PASC] and DSPI_CTARx[ASC].
This number is calculated using the SMPL_PT field in DSPI_MCR set to 0b10.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
40
Freescale Semiconductor
Electrical Characteristics
2
3
PCSx
1
4
SCK output
(CPOL=0)
4
SCK output
(CPOL=1)
9
SIN
10
First data
Last data
Data
12
SOUT
First data
11
Data
Last data
Figure 18. DSPI Classic SPI Timing—Master, CPHA = 0
PCSx
SCK output
(CPOL=0)
10
SCK output
(CPOL=1)
9
SIN
Data
First data
12
SOUT
First data
Last data
11
Data
Last data
Figure 19. DSPI Classic SPI Timing—Master, CPHA = 1
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
41
Electrical Characteristics
3
2
SS
1
4
SCK input
(CPOL=0)
4
SCK input
(CPOL=1)
5
First data
SOUT
9
6
Data
Last data
Data
Last data
10
First data
SIN
11
12
Figure 20. DSPI Classic SPI Timing—Slave, CPHA = 0
SS
SCK input
(CPOL=0)
SCK input
(CPOL=1)
11
5
12
SOUT
First data
9
SIN
Data
Last data
Data
Last data
6
10
First data
Figure 21. DSPI Classic SPI Timing—Slave, CPHA = 1
MPC5565 Microcontroller Data Sheet, Rev. 2.0
42
Freescale Semiconductor
Electrical Characteristics
3
PCSx
4
1
2
SCK output
(CPOL=0)
4
SCK output
(CPOL=1)
9
SIN
10
First data
Last data
Data
12
SOUT
11
First data
Last data
Data
Figure 22. DSPI Modified Transfer Format Timing—Master, CPHA = 0
PCSx
SCK output
(CPOL=0)
SCK output
(CPOL=1)
10
9
SIN
First data
Data
12
SOUT
First data
Data
Last data
11
Last data
Figure 23. DSPI Modified Transfer Format Timing—Master, CPHA = 1
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
43
Electrical Characteristics
3
2
SS
1
SCK input
(CPOL=0)
4
4
SCK input
(CPOL=1)
12
11
5
First data
SOUT
Data
Last data
10
9
Data
First data
SIN
6
Last data
Figure 24. DSPI Modified Transfer Format Timing—Slave, CPHA = 0
SS
SCK input
(CPOL=0)
SCK input
(CPOL=1)
11
5
6
12
First data
SOUT
9
Last data
Data
Last data
10
First data
SIN
Data
Figure 25. DSPI Modified Transfer Format Timing—Slave, CPHA = 1
7
8
PCSS
PCSx
Figure 26. DSPI PCS Strobe (PCSS) Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
44
Freescale Semiconductor
Electrical Characteristics
3.13.9
eQADC SSI Timing
Table 27. EQADC SSI Timing Characteristics
Spec
Rating
Symbol
Minimum
Typical
Maximum
Unit
tFCK
2
—
17
tSYS_CLK
2
FCK period (tFCK = 1 ÷ fFCK) 1, 2
3
Clock (FCK) high time
tFCKHT
tSYS_CLK − 6.5
—
9 × (tSYS_CLK + 6.5)
ns
4
Clock (FCK) low time
tFCKLT
tSYS_CLK − 6.5
—
8 × (tSYS_CLK + 6.5)
ns
5
SDS lead / lag time
tSDS_LL
–7.5
—
+7.5
ns
6
SDO lead / lag time
tSDO_LL
–7.5
—
+7.5
ns
7
EQADC data setup time (inputs)
tEQ_SU
22
—
—
ns
8
EQADC data hold time (inputs)
tEQ_HO
1
—
—
ns
1
SS timing specified at VDDEH = 3.0–5.25 V, TA = TL to TH, and CL = 25 pF with SRC = 0b11. Maximum operating frequency
varies depending on track delays, master pad delays, and slave pad delays.
2 FCK duty cycle is not 50% when it is generated through the division of the system clock by an odd number.
2
3
4
FCK
5
4
SDS
25th
6
SDO
1st (MSB)
5
2nd
26th
External device data sample at
FCK falling-edge
8
7
SDI
1st (MSB) 2nd
25th
26th
EQADC data sample at
FCK rising-edge
Figure 27. EQADC SSI Timing
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
45
Mechanicals
4
Mechanicals
4.1
MPC5565 324 PBGA Pinouts
Figure 28 is a pinout for the MPC5565 324 PBGA package.
NOTE
The MPC5500 devices are pin compatible for software portability and use
the primary function names to label the pins in the BGA diagram. Although
some devices do not support all the primary functions shown in the BGA
diagram, the muxed and GPIO signals on those pins remain available. See
the signals chapter in the device reference manual for the signal muxing.
A
1
2
3
4
5
VSS
VDD
VSTBY
AN37
AN11
B VDD33
VSS
ETPUA ETPUA
C
30
31
6
7
VDDA1 VSSA1
8
9
10
11
12
13
14
15
16
AN1
AN5
VRH
VRL
AN27
AN28
AN35
VSSA0
AN12
MDO11 MDO10 MDO8
AN23
AN26
AN31
AN32
VSSA0
AN13
MDO9
MDO7
AN22
AN25
AN30
AN33
VDDA0
AN14
MDO5
MDO2
AN29
AN34 VDDEH AN15
9
MDO6
MDO3
VDD
AN36
AN39
AN19
AN16
AN0
AN4
REF
BYPC
VSS
VDD
AN8
AN17
AN20
AN21
AN3
AN7
ETPUA ETPUA ETPUA
D
28
29
26
VSS
VDD
AN38
AN9
AN10
AN18
AN2
AN6
AN24
17
18
19
ETPUA ETPUA ETPUA ETPUA
E
24
27
25
21
F
ETPUA ETPUA ETPUA ETPUA
23
22
17
18
G
ETPUA ETPUA ETPUA ETPUA
20
19
14
13
H
20
21
22
VDD
VDD33
VSS
MDO4
MDO0
VSS
MDO1
VSS
VDDE7
VSS
VDDE7
VDDE7
TMS
EVTI
EVTO F
VDDE7 JCOMP
RDY
VDDE7 B
VDD
C
TCK
TDI
D
TDO
TEST
E
MCKO MSEO0 MSEO1 G
VDDEH GPIO
10
203
ETPUA ETPUA ETPUA VDDEH
16
15
10
1
A
GPIO
204
SINB
H
ETPUA ETPUA ETPUA ETPUA
J
6
9
12
11
VSS
VSS
VSS
VSS
VSS
VDDE7
SOUTB PCSB3 PCSB0 PCSB1 J
ETPUA ETPUA ETPUA ETPUA
K
5
8
7
2
VSS
VSS
VSS
VSS
VSS
VSS
PCSA3 PCSB4 SCKB PCSB2 K
ETPUA ETPUA ETPUA ETPUA
L
4
3
1
0
VSS
VSS
VSS
VSS
VSS
VSS
PCSB5 SOUTA
VSS
VSS
VSS
VSS
PCSA1 PCSA0 PCSA2
M
TCRCLK
BDIP
A
CS1
CS0
N
CS3
WE1
WE0
CS2
VDDE2 VDDE2
VSS
VSS
VSS
PCSA4 TXDA PCSA5 VFLASH N
VSS
VSS
VDDE2
VSS
VSS
VSS
CNTXC RXDA RSTOUT
ADDR VDDE2
19
TA
WKP
CFG
ADDR
T
20
ADDR
21
ADDR
12
TS
RXDB
U
ADDR
22
ADDR
23
ADDR
13
ADDR
14
V
ADDR
24
ADDR
25
ADDR
15
ADDR
31
ADDR
Y
28
ADDR
AA
29
AB
ADDR
27
VSS
VSS
No connect. Reserved (W18 & Y19 are shorted to each other)
VDDE2 VDD33 VDDE2
DATA
11
DATA
12
DATA
14
EMIOS EMIOS VDDEH EMIOS EMIOS VDDE5
21
8
2
4
12
DATA
13
DATA
15
EMIOS EMIOS EMIOS EMIOS EMIOS CNTXA VDDE5
6
10
15
17
22
DATA
8
DATA
9
DATA
10
GPIO
207
DATA
5
DATA
7
VDD
VDDE2
VDD
VDDE2
DATA
1
VDDE2
GPIO
206
DATA
2
DATA
3
DATA
4
DATA
6
OE
5
6
7
8
9
VSS
VSS
VDD
VDDE2
DATA
0
1
2
3
4
NC
RST
CFG
P
CNRXC TXDB RESET R
BOOT
CFG1
PLL
CFG2
VDDEH PLL
6
CFG1
BOOT
CFG0
EXTAL U
VRC
CTL
PLL
CFG0
XTAL
V
VDD
SYN
W
VDD
VDD
M
VDDE2
ADDR
R
18
ADDR
ADDR
W
VDDE2
30
26
VPP
VSS
ADDR
RD_WR VDD33
17
NC
SCKA L
VSS
ADDR
P
16
Note:
SINA
VSS
VDD
VRC33
NC
VSS
VDD
VSS
SYN
T
VDD33 Y
VDDE2 EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNRXA VDDE5 CLKOUT VSS
3
5
9
13
23
16
19
VDD
AA
EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS EMIOS CNTXB CNRXB VDDE5
20
0
1
4
7
11
14
18
ENG
CLK
VSS
AB
21
22
10
11
12
13
14
15
16
17
18
19
20
Figure 28. MPC5565 324 Package
MPC5565 Microcontroller Data Sheet, Rev. 2.0
46
Freescale Semiconductor
Mechanicals
4.2
MPC5565 324-Pin Package Dimensions
The package drawings of the MPC5565 324-pin TEPBGA package are shown in Figure 29.
Figure 29. MPC5565 324 TEPBGA Package
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
47
Mechanicals
Figure 29. MPC5565 324 TEPBGA Package (continued)
MPC5565 Microcontroller Data Sheet, Rev. 2.0
48
Freescale Semiconductor
Revision History for the MPC5565 Data Sheet
5
Revision History for the MPC5565 Data Sheet
The history of revisions made to this data sheet are shown in this section. The changes are divided into
each revision of this document. The substantive changes incorporated in MPC5565 Data Sheet Rev. 1.0 to
produce Rev. 2.0 of this document are grouped as follows:
• Global and text changes
• Table and figure changes
Within each group, the changes are listed in sequential order.
5.1
Changes to Revision 1.0 in Revision 2.0
The following table lists the substantive text changes made to paragraphs.
Table 28. Text Changes Between Rev. 1.0 and 2.0
Location
Description of Changes
Throughout:
Changed ‘TA = TL – TH’ to ‘TA = TL to TH.’
Title page:
Changed the Revision number from 1.0 to 2.0. Made the same changes in the lower left corner of the back page.
Section 1, “Overview”
• Fourth paragraph, First sentence: Deleted ‘of the MPC5500 family’; Second to last sentence: Deleted ‘can’.
• Fifth paragraph, First sentence: Replaced ‘MPC5500 family’ with ‘MPC5565’; Last sentence: Replaced ‘can be’
with ‘is’.
• Sixth paragraph, First sentence: Replaced ‘MPC5500 family’ with ‘MPC5565’;
• Second to last paragraph: Rewrote to read: The MCU has an on-chip enhanced queued dual analog-to-digital
converter (eQADC) The 324 package has 40-channels.
Section 3.1, “Maximum Ratings:
Changed title from ‘Maximum Rating’ to ‘Maximum Ratings.’
Section 3.2.1, “General Notes for Specifications at Maximum Junction Temperature”
Updated the address of Semiconductor Equipment and Materials International
3081 Zanker Rd.
San Jose, CA., 95134
(408) 943-6900
Section 3.7, “Power-Up/Down Sequencing”
Last paragraph: Changed the first sentence FROM , , , the voltage on the pins goes to high-impedance until . . .
TO. . .the pins go to a high-impedance state until . . .
Section 3.7.3, “Power-Down Sequence (VRC33 Grounded)”
Last sentence: Changed from: ‘This ensures that the digital 1.5 V logic, which is reset by the ORed POR only and
can cause the 1.5 V supply to decrease below its specification, is reset properly.’
To: ‘This ensures that the digital 1.5 V logic, which is reset only by an ORed POR and can cause the 1.5 V supply
to decrease less than its specification, resets correctly.’
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
49
Revision History for the MPC5565 Data Sheet
Table 28. Text Changes Between Rev. 1.0 and 2.0 (continued)
Location
Description of Changes
Section 4.1, “MPC5565 324 PBGA Pinouts”
Added the following NOTE before the 324 BGA Map:
NOTE
The MPC5500 devices are pin compatible for software portability and use the primary
function names to label the pins in the BGA diagram. Although some devices do not support
all the primary functions shown in the BGA diagram, the muxed and GPIO signals on those
pins remain available. See the signals chapter in the device reference manual for the signal
muxing.
The following table lists the information that changed in the tables between Rev. 1.0 and 2.0.
Table 29. MPC5565 Changes Between Rev. 1.0 and 2.0
Location
Description of Changes
Table 2 Absolute Maximum Ratings:
• Added footnote 7 to Spec 12 ‘Internal structures hold the input voltage less than the maximum voltage on all pads
powered by VDDE supplies, if the maximum injection current specification is met (2 mA for all pins) and VDDE is
within the operating voltage specifications.’
Table 4 EMI Testing Specifications:
• Table Title: Footnote 1: Deleted the last sentence: “The values in this specification reflect EMI performance with
frequency modulation (FM) turned off. For better EMI performance, enable FM.’
Table 5 ESD Ratings:
Changed footnote 2 from:
• ‘Device failure is defined as: ‘If after exposure to ESD pulses, the device no longer meets the device specification
requirements. Complete DC parametric and functional testing will be performed per applicable device
specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.’
to:
• Device failure is defined as: ‘If after exposure to ESD pulses, the device does not meet the device specification
requirements, which includes the complete DC parametric and functional testing at room temperature and hot
temperature.
Table 6 VCR/POR Electrical Specifications:
• Added footnote 1 to specs 1, 2, and 3 that reads: The internal POR signals are VPOR15, VPOR33, and VPOR5.
On power up, assert RESET before the internal POR negates. RESET must remain asserted until the power
supplies are within the operating conditions as specified in Table 9 DC Electrical Specifications. On power down,
assert RESET before any power supplies fall outside the operating conditions and until the internal POR asserts.
• Reformatted columns.
Table 9 DC Electrical Specifications:
• Added (TA = TL to TH) to the table title.
• Added footnote that reads: VDDE2 and VDDE3 are limited to 2.25–3.6 V only if SIU_ECCR[EBTS] = 0; VDDE2 and
VDDE3 have a range of 1.6–3.6 V if SIU_ECCR[EBTS] =1.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
50
Freescale Semiconductor
Revision History for the MPC5565 Data Sheet
Table 29. MPC5565 Changes Between Rev. 1.0 and 2.0 (continued)
Location
Description of Changes
Table 17 Pad AC Specifications:
• Footnote 1, Changed ‘VDDEH = 4.5–5.5;’ to ‘VDDEH = 4.5–5.25;’
• Footnote 3, Changed from ‘Out delay. . .’ to ‘The output delay. . .’,
• Changed from ‘ Add a maximum of one system clock to the output delay to get the output delay with respect to
the system clock‘ to ‘To calculate the output delay with respect to the system clock, add a maximum of one system
clock to the output delay.’
• Footnote 4: Changed ‘Delay’ to ‘The output delay.’
Table 19 Reset and Configuration Pin Timing
• Footnote 1: Removed VDD =1.35–1.65.
Table 20 JTAG Pin AC Electrical Characteristics
• Footnote 1: Removed VDD =1.35–1.65; and VDD33 and VDDSYN = 3.0–3.6 V.
Table 22 Bus Operation Timing:
• Specifications 5 and 6. Changed EBTS to SIU_ECCR[EBTS].
• Specifications 7 and 8: Removed CS[0:3], BDIP, OE, and WE/BE[0:3] because these pins are not used on the
input signal to CLKOUT.
• Specification 7: Removed CAL_CS[0, 2:3], CAL_OE, and CAL_WE/BE[0:1] because these pins are not used on
the input signal to CLKOUT.
• Specification 8: Added to the beginning of the calibration section: CLKOUT positive edge to input signal invalid
(hold time). Removed CAL_CS[0, 2:3], CAL_OE, and CAL_WE/BE[0:1] because these pins are not used on the
input signal to CLKOUT.
• Footnote 1: Deleted VDD = 1.35–1.65; and VDD33 and VDDSYN = 3.0–3.6 V.
• Added footnote 2: “Speed is the nominal maximum frequency. Max. speed is the maximum speed allowed
including frequency modulation (FM). 82 MHz parts allow for 80 MHz system clock + 2% FM; 114 MHz parts allow
for 112 MHz system clock + 2% FM; and 135 MHz parts allow for 132 MHz system clock + 2% FM.’
• Added footnotes 5, 6, and 7, one each for the DATA[0:31], TEA, and WE/BE[0:3] signals in the table: Due to pin
limitations, the DATA[16:31], TEA, and WE/BE[2:3] signals are not available on the 324 package.
• Footnote 8: Changed EBTS to SIU_ECCR[EBTS].
Table 23 External Interrupt Timing (IRQ Signals)
• Footnote 1: Removed VDD = 1.35–1.65 V; changed VDDEH = 3.0–5.5 V to VDDEH = 3.0–5.25 V.
Table 24 eTPU Timing
• Footnote 1: Changed VDDEH = 3.0–5.5 V to VDDEH = 3.0–5.25 V.
Table 25 eMIOS Timing
• Footnote 1: Changed VDDEH = 3.0–5.5 V to VDDEH = 3.0–5.25 V.
Table 26 DSPI Timing:
• Specification 1: SCK cycle time. Changed 80 MHz column, Min.: from 25 to 24.4; 112 MHz columns, Min.: from
17.9 to 17.5, Max: from 2.0 to 2.1; 132 MHz columns, Min.: from 15.2 to 14.8, Max: from 1.7 to 1.8.
• Footnote 1, changed ‘VDDEH = 3.0–5.5 V;’ to ‘VDDEH = 3.0–5.25 V;’
• Table Title: Added footnote that reads: Speed is the nominal maximum frequency. Max speed is the maximum
speed allowed including frequency modulation (FM). 82 MHz parts allow for 80 MHz system clock + 2% FM;
114 MHz parts allow for 112 MHz system clock + 2% FM, 135 MHz parts allow for 132 MHz system clock + 2%
FM.
Table 27 EQADC SSI Timing Characteristics
• Footnote 1: Changed VDDEH = 3.0–5.5 V to VDDEH = 3.0–5.25 V.
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
51
Revision History for the MPC5565 Data Sheet
5.2
Changes to Revision 0.0 in Revision 1.0
The following table lists the information that changed in the tables between Rev. 0.0 and 1.0.
Table 30. MPC5565 Changes Between Rev. 0.0 and 1.0
Location
Description of Changes
Table 6 VCR/POR Electrical Specifications:
• Added footnote 1 to specs 1, 2, and 3 that reads: On power up, assert RESET before VPOR15, VPOR33, and VPOR5
negate (internal POR). RESET must remain asserted until the power supplies are within the operating conditions
as specified in Table 9 DC Electrical Specifications. On power down, assert RESET before any power supplies
fall outside the operating conditions and until the internal POR asserts.
Table 9 DC Electrical Specifications:
• Added (TA = TL to TH) to the table title.
Table 22 Bus Operation Timing:
• External Bus Frequency in the table heading: Added footnote that reads: Speed is the nominal maximum
frequency. Max speed is the maximum speed allowed including frequency modulation (FM). 82 MHz parts allow
for 80 MHz system clock + 2% FM; 114 MHz parts allow for 112 MHz system clock + 2% FM, and 135 MHz parts
allow for 132 MHz system clock + 2% FM.
• Specifications 5, 6, 7, and 8: Reordered the EBI signals within each specification.
• Specs 7 and 8: Removed from external bus interface: BDIP, OE, and WE/BE[0:3].
• Footnote 1: Removed VDD = 1.35–1.65 V, and VDD33 and VDDSYN = 3.0–3.6 V.
Table 25 eMIOS Timing:
• Deleted (MTS) from the heading, table, and footnotes.
• Footnote 1: Deleted ‘. . .fSYS = 132 MHz. . .’, ‘. . .VDD33 and VDDSYN = 3.0–3.6 V. . .’ and ‘ . . .and CL = 200 pF
with SRC = 0b11.’
• Added Footnote 2: ‘This specification does not include the rise and fall times. When calculating the minimum
eMIOS pulse width, include the rise and fall times defined in the slew rate control fields (SRC) of the pad
configuration registers (PCR).’
MPC5565 Microcontroller Data Sheet, Rev. 2.0
52
Freescale Semiconductor
Revision History for the MPC5565 Data Sheet
MPC5565 Microcontroller Data Sheet, Rev. 2.0
Freescale Semiconductor
53
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Document Number: MPC5565
Rev. 2.0
11/2008
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2008. All rights reserved.
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
For information on Freescale’s Environmental Products program, go to
http://www.freescale.com/epp.
Similar pages