MSK MSK590XERHG Dual rad tolerant /- voltage regulator Datasheet

ISO-9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP.
DUAL RAD TOLERANT
+/VOLTAGE REGULATOR
5901RH
SERIES
4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
FEATURES:
MIL-PRF-38534 CERTIFIED
25KRAD(SI) Total Dose Performance
Internal Thermal Overload Protection
Output Current to 1.5 Amps
Output Voltage Internally Trimmed to ±1% Accuracy
Available to DSCC SMD #TBD
Lead Form Options: Straight and Gull Wing
Alternate Voltage Combinations Available
MSK590XRH
DESCRIPTION:
MSK590XRHG
The MSK 5901RH series are dual Radiation Tolerant +/- voltage regulators offering low dropout and output accuracy to
±1% maximum. Excellent line and load regulation characteristics ensure highly accurate performance. In radiation environments, a total dose rating of 25KRAD(SI) provides highly reliable performance. The MSK 5901RH series regulators are
equipped with internal thermal overload protection. The devices are packaged in a space efficient 20 pin flatpack with two
lead form options, straight and gull wing.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
1
2
3
4
5
6
7
8
9
10
Switching Power Supply Post Regulators
Constant Voltage/Current Regulators
High Efficiency Linear Regulators
1
-VRTN
-VOUT
-VOUT
-VOUT
-VOUT
+VRTN
+VOUT
+VOUT
+VOUT
+VOUT
20
19
18
17
16
15
14
13
12
11
-VIN
-VIN
-VIN
-VIN
-Ccomp
+Ccomp
+VIN
+VIN
+VIN
+VIN
Rev. D 7/05
ABSOLUTE MAXIMUM RATINGS
+VIN
-VIN
PD
+IOUT
-IOUT
TJ
+Input Voltage (VIN-VOUT)
-Input Voltage (VIN-VOUT)
Power Dissipation
+Output Current
-Output Current
Junction Temperature
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
+40VDC
-40VDC
Internally Limited
1.5A
1.5A
+150°C
○
○
○
8
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
TST Storage Temperature Range
TLD Lead Temperature Range
(10 Seconds)
TC Case Operating Temperature
MSK 5901RH-5909RH
MSK 5901RH-5909RH(K/H/E)
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-65°C to +150°C
300°C
○
○
○
○
○
○
-40°C to +85°C
-55°C to +125°C
○
ELECTRICAL SPECIFICATIONS
Parameter
Test Conditions
Group A MSK 590XRH K/H/E
3
Subgroup
Typ.
Min.
Max.
4
7
MSK 590XRH
2
Units
Min.
Typ.
Max.
POSITIVE OUTPUT REGULATORS:
1
-
±0.2
±1.0
-
±0.2
±1.5
%
2,3
-
±0.8
±3.0
-
-
-
%
1
-
1.6
3.0
-
1.6
3.5
V
2,3
-
1.9
3.0
-
-
-
V
1
-
±0.2
±2.0
-
±0.2
±2.5
%
V IN=VOUT+3V
2,3
-
±0.4
±2.5
-
-
-
%
IOUT=10mA
1
-
±0.6
±1.5
-
±0.6
±2.0
%
VOUT+3V≤V IN≤35V
2,3
-
±1.0
±2.5
-
-
-
%
JUNCTION TO CASE @ 125°C
-
-
9.5
10.5
-
9.5
1
-
±0.2
±1.0
-
±0.2
±1.5
%
2,3
-
±0.8
±3.0
-
-
-
%
1
-
1.9
3.0
-
1.9
3.0
V
2,3
-
1.5
3.0
-
-
-
V
10mA≤IOUT≤0.5A
1
-
±0.2
±2.0
-
±0.2
±2.5
%
VIN=VOUT -3V
2,3
-
±0.4
±2.5
-
-
-
%
IOUT=10mA
1
-
±0.1
±1.5
-
±0.1
±2.0
%
-30V≤V IN≤VOUT-3V
2,3
-
±0.2
±2.5
-
-
-
%
-
-
11.5
12.5
-
11.5
Output Voltage Tolerance
IOUT=10mA; VIN=VOUT+3V
IOUT=0.5A; ∆V OUT=1%
Dropout Voltage
10mA≤IOUT≤0.5A
Load Regulation
Line Regulation
Thermal Resistance 1
11.0 °C/W
NEGATIVE OUTPUT REGULATORS:
Output Voltage Tolerance
Dropout Voltage
Load Regulation
Line Regulation
Thermal Resistance 1
IOUT=10mA; VIN=VOUT -3V
IOUT=0.5A; ∆V OUT=1%
JUNCTION TO CASE @ 125°C
PART
5
NUMBER
NOTES:
1
2
3
4
5
6
7
8
Guaranteed by design but not tested. Typical parameters are representative of actual device
performance but are for reference only.
Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified.
Military grade devices shall be 100% tested to subgroups 1,2 and 3.
Subgroup 1 TA=TC=+25°C
Subgroup 2 TA=TC=+125°C
Subgroup 3 TA=TC=-55°C
Please consult the factory if alternate output voltages are required.
For positive regulator, output decoupled to ground using 1µF minimum tantalum capacitor unless
otherwise specified. For negative regulator, output decoupled to ground using 1µF minimum
tantanlum capacitor.
For complete radiation test data, consult "MSK 5901RH Total Dose Test Report".
Continuous operation at or above absolute maximum ratings may adversly effect the device
performance and/or life cycle.
2
13.0 °C/W
OUTPUT VOLTAGES
POSITIVE
NEGATIVE
MSK5901
5.0
5.0
MSK5902
5.0
5.2
MSK5903
12.0
5.0
MSK5904
12.0
12.0
MSK5905
15.0
15.0
MSK5906
15.0
5.0
MSK5907
5.0
12.0
MSK5908
5.0
15.0
MSK5909
10.0
10.0
Rev. D 7/05
APPLICATION NOTES
TYPICAL APPLICATION CIRCUIT
CAPACITOR SELECTION
POSITIVE REGULATOR
INPUT CAPACITOR:
An input bypass capacitor is recommenced when using the
MSK 5901 series regulators. This is especially true if the regulator is located farther than 6 inches from the power supply filter
capacitors. For most applications a 1µF solid tantalum capacitor
will be suitable.
LOAD REGULATION
OUTPUT CAPACITOR:
A minimum of a 1µF solid tantalum capacitor should also be
used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance.
It is important to keep the output connection between the regulator and the load as short as possible since this directly affects
the load regulation. For example, if 20 gauge wire were used
which has a resistance of about 0.008 ohms per foot, this would
result in a drop of 8mV/ft at 1Amp of load current. It is also
important to follow the capacitor selection guidelines to achieve
best performance.
+CCOMP CAPACITOR:
For improved ripple rejection, +Ccomp can be bypassed to
ground with a 10µF tantalum capacitor. This bypass capacitor
will provide 80dB ripple rejection. Increased capacitance above
10µF does not improve the ripple rejection at frequencies above
120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for
clarification. If the bypass capacitor is not used, it should be left
open since it is internally connected to the regulator.
HEAT SINKING
To determine if a heat sink is required for your application
and if so, what type, refer to the thermal model and governing equation below.
Governing Equation: Tj = Pd x (Rθjc + Rθcs + Rθsa) + Ta
WHERE
Tj = Junction Temperature
Pd = Total Power Dissipation
Rθjc = Junction to Case Thermal Resistance
Rθcs = Case to Heat Sink Thermal Resistance
Rθsa = Heat Sink to Ambient Thermal Resistance
Tc = Case Temperature
Ta = Ambient Temperature
Ts = Heat Sink Temperature
NEGATIVE REGULATOR
INPUT CAPACITOR:
Once again, if the regulator will be farther than 6 inches from
power supply filter capacitors, then an input capacitor will be
required on the negative regulator. It is recommended that a
1µF solid tantalum capacitor be used.
EXAMPLE:
This example demonstrates an analysis where the output currents are at 0.5 amp each and both inputs are 8V.
OUTPUT CAPACITOR:
A minimum of a 1µF solid tantalum capacitor should also be
used at the output to insure stability. Any increase of this output capacitor larger than 10µF will only improve output impedance.
Conditions for MSK 5901RH:
+Vin = +8.0V; Iout = 0.5A Positive Regulator
1.) Assume 45° heat spreading model.
2.) Find positive regulator power dissipation:
-CCOMP CAPACITOR:
For improved ripple rejection, -Ccomp can be bypassed to
ground with a 10µF tantalum capacitor. This bypass capacitor
will provide 80dB ripple rejection. Increased capacitance above
10µF does not improve the ripple rejection at frequencies above
120Hz. If the Ccomp bypass capacitor is used, it may be necessary to add a protection diode to protect the regulator from capacitor discharge damage. See Typical Applications Circuit for
clarification. If the bypass capacitor is not used, it should be left
open since it is internally connected to the regulator.
Pd = (Vin - Vout)(Iout)
Pd = (+8V-5V)(0.5A)
Pd = 1.5W
3.) For conservative design, set Tj = +125°C Max.
4.) For this example, worst case Ta = +90°C.
5.) Rθjc = 10.5°C/W from the Electrical Specification Table.
6.) Rθcs = 0.15°C/W for most thermal greases.
7.) Rearrange governing equation to solve for Rθsa:
Rθsa= ((Tj - Ta)/Pd) - (Rθjc) - (Rθcs)
= (125°C-90°C)/1.5W - 10.5°C/W - 0.15°C/W
= 12.7°C/W
The same exercise must be performed for the negative regulator.
3
Rev. D 7/05
TYPICAL PERFORMANCE CURVES
POSITIVE
NEGATIVE
4
Rev. D 7/05
MECHANICAL SPECIFICATIONS
MSK590XRH
WEIGHT= 3.3 GRAMS TYPICAL
NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED.
ESD Triangle indicates pin 1.
ORDERING INFORMATION
Part
Number
Screening Level
MSK590XRH
Industrial
MSK590XHRH
MIL-PRF-38534 CLASS H
MSK590XKRH
MIL-PRF-38534 CLASS K
MSK590XERH
EXTENDED RELIABILITY
DSCC SMD TBD
TBD
X - Designates voltage selection (MSK 5901-5909)
5
Rev. D 7/05
MECHANICAL SPECIFICATIONS CONTINUED
MSK590XRHG
WEIGHT= 3.3 GRAMS TYPICAL
NOTE: ALL DIMENSIONS ARE ±0.010 INCHES UNLESS OTHERWISE LABELED.
ESD Triangle indicates pin 1.
ORDERING INFORMATION
Part
Number
Screening Level
MSK590XRHG
Industrial
MSK590XHRHG
MIL-PRF-38534 CLASS H
MSK590XKRHG
MIL-PRF-38534 CLASS K
MSK590XERHG
EXTENDED RELIABILITY
DSCC SMD TBD
TBD
X - Designates voltage selection (MSK 5901-5909)
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
Fax (315) 701-6752
www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
Contact MSK for MIL-PRF-38534 Class H, Class K and Appendix G (radiation) status.
6
Rev. D 7/05
Similar pages