ON MTD20N06V Nâ channel dpak Datasheet

MTD20N06V
Power Field Effect
Transistor
N−Channel DPAK
This device is a new technology designed to achieve an
on−resistance area product about one−half that of standard MOSFETs.
This new technology more than doubles the present cell density of our
50 and 60 V devices. This device is designed to withstand high energy
in the avalanche and commutation modes. Designed for low voltage,
high speed switching applications in power supplies, converters and
power motor controls, these devices are particularly well suited for
bridge circuits where diode speed and commutating safe operating
areas are critical and offer additional safety margin against unexpected
voltage transients.
http://onsemi.com
V(BR)DSS
RDS(on) TYP
ID MAX
60 V
65 mW
20 A
N−Channel
D
Features
• On−resistance Area Product about One−half that of Standard
G
S
MARKING
DIAGRAM
Symbol
Value
Unit
Drain−to−Source Voltage
VDSS
60
Vdc
Drain−to−Gate Voltage (RGS = 1.0 MΩ)
VDGR
60
Vdc
Gate−to−Source Voltage − Continuos
− Non−repetitive (tp ≤ 10 ms)
VGS
VGSM
± 20
± 25
Vdc
Vpk
ID
ID
20
13
70
Adc
PD
60
0.4
2.1
Watts
W/°C
Watts
Operating and Storage Temperature Range
TJ, Tstg
−55 to
175
°C
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vdc, Peak IL =
20 Apk, L = 1.0 mH, RG = 25 Ω)
EAS
200
mJ
Thermal Resistance − Junction to Case
− Junction to Ambient (Note 1)
− Junction to Ambient (Note 2)
RθJC
RθJA
RθJA
2.5
100
71.4
°C/W
TL
260
°C
Rating
Drain Current − Continuous
− Continuous @ 100°C
− Single Pulse (tp ≤ 10 μs)
Total Power Dissipation
Derate above 25°C
Total Power Dissipation @ 25°C (Note 2)
Maximum Lead Temperature for Soldering
Purposes, 1/8″ from case for 10 seconds
IDM
4
Drain
4
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Apk
1 2
YWW
T20
N06V
•
•
•
•
MOSFETs with New Low Voltage, Low RDS(on) Technology
Faster Switching than Predecessors
Avalanche Energy Specified
IDSS and VDS(on) Specified at Elevated Temperature
Surface Mount Package Available in 16 mm 13−inch/2500 Unit Tape
& Reel, Add T4 Suffix to Part Number
3
DPAK
CASE 369C
(Surface Mount)
Style 2
T20N06V
Y
WW
2
1 Drain 3
Gate
Source
= Device Code
= Year
= Work Week
ORDERING INFORMATION
Package
Shipping†
MTD20N06V
DPAK
75 Units/Rail
MTD20N06VT4
DPAK
2500 Tape & Reel
Device
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. When surface mounted to an FR4 board using the minimum recommended
pad size.
2. When surface mounted to an FR4 board using 0.5 sq. in. drain pad size.
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 5
1
Publication Order Number:
MTD20N06V/D
MTD20N06V
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
60
−
−
69
−
−
−
−
−
−
10
100
−
−
100
2.0
−
2.8
5.0
4.0
−
−
0.065
0.080
−
−
−
−
2.0
1.9
gFS
6.0
8.0
−
mhos
pF
OFF CHARACTERISTICS
Drain−to−Source Breakdown Voltage
(VGS = 0 Vdc, ID = 0.25 mAdc)
Temperature Coefficient (Positive)
(Cpk ≥ 2.0) (3)
V(BR)DSS
Zero Gate Voltage Drain Current
(VDS = 60 Vdc, VGS = 0 Vdc)
(VDS = 60 Vdc, VGS = 0 Vdc, TJ = 150°C)
IDSS
Gate−Body Leakage Current (VGS = ± 20 Vdc, VDS = 0 Vdc)
IGSS
Vdc
mV/°C
μAdc
nAdc
ON CHARACTERISTICS (1)
Gate Threshold Voltage
(VDS = VGS, ID = 250 μAdc)
Threshold Temperature Coefficient (Negative)
(Cpk ≥ 2.0) (3)
Static Drain−to−Source On−Resistance
(VGS = 10 Vdc, ID = 10 Adc)
(Cpk ≥ 2.0) (3)
Drain−to−Source On−Voltage
(VGS = 10 Vdc, ID = 10 Adc)
(VGS = 10 Vdc, ID = 10 Adc, TJ = 150°C)
VGS(th)
RDS(on)
VDS(on)
Forward Transconductance (VDS = 6.0 Vdc, ID = 10 Adc)
Vdc
mV/°C
Ohm
Vdc
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
(VDS = 25 Vdc, VGS = 0 Vdc,
f = 1.0 MHz)
Ciss
−
590
830
Coss
−
180
250
Crss
−
40
80
td(on)
−
8.7
20
SWITCHING CHARACTERISTICS (2)
Turn−On Delay Time
Rise Time
Turn−Off Delay Time
(VDD = 30 Vdc, ID = 20 Adc,
VGS = 10 Vdc,
RG = 9.1 Ω)
Fall Time
Gate Charge
(VDS = 48 Vdc, ID = 20 Adc,
VGS = 10 Vdc)
tr
−
77
150
td(off)
−
26
50
tf
−
46
90
QT
−
28
40
Q1
−
4.0
−
Q2
−
9.0
−
Q3
−
8.0
−
−
−
1.05
0.96
1.6
−
trr
−
60
−
ta
−
52
−
tb
−
8.0
−
QRR
−
0.172
−
−
−
3.5
4.5
−
−
−
7.5
−
ns
nC
SOURCE−DRAIN DIODE CHARACTERISTICS
Forward On−Voltage (1)
(IS = 20 Adc, VGS = 0 Vdc)
(IS = 20 Adc, VGS = 0 Vdc, TJ = 150°C)
Reverse Recovery Time
(IS = 20 Adc, VGS = 0 Vdc,
dIS/dt = 100 A/μs)
Reverse Recovery Stored Charge
VSD
Vdc
ns
μC
INTERNAL PACKAGE INDUCTANCE
Internal Drain Inductance
(Measured from contact screw on tab to center of die)
(Measured from the drain lead 0.25″ from package to center of die)
LD
Internal Source Inductance
(Measured from the source lead 0.25″ from package to source bond pad)
LS
(1) Pulse Test: Pulse Width ≤ 300 μs, Duty Cycle ≤ 2%.
(2) Switching characteristics are independent of operating junction temperature.
(3) Reflects typical values.
Max limit − Typ
Cpk =
3 x SIGMA
http://onsemi.com
2
nH
nH
MTD20N06V
TYPICAL ELECTRICAL CHARACTERISTICS
8V
I D , DRAIN CURRENT (AMPS)
35
30
7V
25
20
6V
15
10
5V
5
4V
1
3
2
4
5
6
7
9
8
20
15
10
2
0.1
25°C
0.08
0.06
- 55°C
0.04
0.02
6
7
5
10
15
25
20
30
ID, DRAIN CURRENT (AMPS)
35
40
8
9
0.11
TJ = 25°C
0.1
0.09
0.08
VGS = 10 V
0.07
0.06
15 V
0.05
0.04
0
Figure 3. On−Resistance versus Drain Current
and Temperature
10
5
20
30
15
25
ID, DRAIN CURRENT (AMPS)
35
40
Figure 4. On−Resistance versus Drain Current
and Gate Voltage
2.0
35
VGS = 0 V
VGS = 10 V
ID = 10 A
30
1.5
I DSS , LEAKAGE (nA)
RDS(on) , DRAIN-TO-SOURCE RESISTANCE
(NORMALIZED)
5
Figure 2. Transfer Characteristics
TJ = 100°C
1.25
1
0.75
0.5
TJ = 125°C
25
20
15
10
100°C
5
0.25
0
-50
4
Figure 1. On−Region Characteristics
0.12
1.75
3
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
VGS = 10 V
0
100°C
25
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
0.14
0
25°C
30
0
10
0.18
0.16
TJ = -55°C
5
RDS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS)
0
VDS ≥ 10 V
35
TJ = 25°C
0
R DS(on) , DRAIN-TO-SOURCE RESISTANCE (OHMS)
40
9V
VGS = 10V
I D , DRAIN CURRENT (AMPS)
40
-25
0
25
50
75
100 125
TJ, JUNCTION TEMPERATURE (°C)
150
0
175
0
Figure 5. On−Resistance Variation with
Temperature
50
10
20
30
40
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 6. Drain−To−Source Leakage
Current versus Voltage
http://onsemi.com
3
60
MTD20N06V
POWER MOSFET SWITCHING
The capacitance (Ciss) is read from the capacitance curve at
Switching behavior is most easily modeled and predicted
a voltage corresponding to the off−state condition when
by recognizing that the power MOSFET is charge
calculating td(on) and is read at a voltage corresponding to the
controlled. The lengths of various switching intervals (Δt)
on−state when calculating td(off).
are determined by how fast the FET input capacitance can
be charged by current from the generator.
At high switching speeds, parasitic circuit elements
The published capacitance data is difficult to use for
complicate the analysis. The inductance of the MOSFET
calculating rise and fall because drain−gate capacitance
source lead, inside the package and in the circuit wiring
varies greatly with applied voltage. Accordingly, gate
which is common to both the drain and gate current paths,
charge data is used. In most cases, a satisfactory estimate of
produces a voltage at the source which reduces the gate drive
average input current (IG(AV)) can be made from a
current. The voltage is determined by Ldi/dt, but since di/dt
rudimentary analysis of the drive circuit so that
is a function of drain current, the mathematical solution is
complex. The MOSFET output capacitance also
t = Q/IG(AV)
complicates the mathematics. And finally, MOSFETs have
During the rise and fall time interval when switching a
finite internal gate resistance which effectively adds to the
resistive load, VGS remains virtually constant at a level
resistance of the driving source, but the internal resistance
known as the plateau voltage, VSGP. Therefore, rise and fall
is difficult to measure and, consequently, is not specified.
times may be approximated by the following:
The resistive switching time variation versus gate
tr = Q2 x RG/(VGG − VGSP)
resistance (Figure 9) shows how typical switching
tf = Q2 x RG/VGSP
performance is affected by the parasitic circuit elements. If
the parasitics were not present, the slope of the curves would
where
maintain a value of unity regardless of the switching speed.
VGG = the gate drive voltage, which varies from zero to VGG
The circuit used to obtain the data is constructed to minimize
RG = the gate drive resistance
common inductance in the drain and gate circuit loops and
and Q2 and VGSP are read from the gate charge curve.
is believed readily achievable with board mounted
components. Most power electronic loads are inductive; the
During the turn−on and turn−off delay times, gate current is
data in the figure is taken with a resistive load, which
not constant. The simplest calculation uses appropriate
approximates an optimally snubbed inductive load. Power
values from the capacitance curves in a standard equation for
MOSFETs may be safely operated into an inductive load;
voltage change in an RC network. The equations are:
however, snubbing reduces switching losses.
td(on) = RG Ciss In [VGG/(VGG − VGSP)]
td(off) = RG Ciss In (VGG/VGSP)
1600
VDS = 0 V
C, CAPACITANCE (pF)
VGS = 0 V
TJ = 25°C
Ciss
1400
1200
Crss
1000
800
Ciss
600
400
Coss
200
0
Crss
10
0
5
VGS
5
10
15
20
25
VDS
GATE-TO-SOURCE OR DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
http://onsemi.com
4
30
9
VGS
QT
27
8
24
7
21
6
18
Q2
Q1
5
15
4
12
9
3
2
1
0
TJ = 25°C
ID = 20 A
Q3
VDS
0
5
10
15
20
25
6
3
0
30
1000
t, TIME (ns)
10
VDS , DRAIN-TO-SOURCE VOLTAGE (VOLTS)
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
MTD20N06V
TJ = 25°C
ID = 20 A
VDD = 30 V
VGS = 10 V
100
tr
tf
td(off)
10
td(on)
1
1
10
Qg, TOTAL GATE CHARGE (nC)
RG, GATE RESISTANCE (OHMS)
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
1
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
20
I S , SOURCE CURRENT (AMPS)
18
TJ = 25°C
VGS = 0 V
16
14
12
10
8
6
4
2
0
0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 0.95
1
1.05 1.1
VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
reliable operation, the stored energy from circuit inductance
The Forward Biased Safe Operating Area curves define
dissipated in the transistor while in avalanche must be less
the maximum simultaneous drain−to−source voltage and
than the rated limit and adjusted for operating conditions
drain current that a transistor can handle safely when it is
differing from those specified. Although industry practice is
forward biased. Curves are based upon maximum peak
to rate in terms of energy, avalanche energy capability is not
junction temperature and a case temperature (TC) of 25°C.
a constant. The energy rating decreases non−linearly with an
Peak repetitive pulsed power limits are determined by using
increase of peak current in avalanche and peak junction
the thermal response data in conjunction with the procedures
temperature.
discussed
in
AN569,
“Transient
Thermal
Although many E−FETs can withstand the stress of
Resistance−General Data and Its Use.”
drain−to−source avalanche at currents up to rated pulsed
Switching between the off−state and the on−state may
current (IDM), the energy rating is specified at rated
traverse any load line provided neither rated peak current
continuous current (ID), in accordance with industry
(IDM) nor rated voltage (VDSS) is exceeded and the
custom. The energy rating must be derated for temperature
transition time (tr,tf) do not exceed 10 μs. In addition the total
as shown in the accompanying graph (Figure 12). Maximum
power averaged over a complete switching cycle must not
energy at currents below rated continuous ID can safely be
exceed (TJ(MAX) − TC)/(RθJC).
assumed to equal the values indicated.
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
http://onsemi.com
5
MTD20N06V
SAFE OPERATING AREA
200
VGS = 20 V
SINGLE PULSE
TC = 25°C
EAS, SINGLE PULSE DRAIN-TO-SOURCE
AVALANCHE ENERGY (mJ)
I D , DRAIN CURRENT (AMPS)
100
10 μs
10
100 μs
1 ms
10 ms
dc
1
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
ID = 20 A
180
160
140
120
100
80
60
40
20
0
0.1
0.1
1
10
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
25
100
50
75
100
125
175
150
TJ, STARTING JUNCTION TEMPERATURE (°C)
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
1.00
r(t), NORMALIZED EFFECTIVE
TRANSIENT THERMAL RESISTANCE
D = 0.5
0.2
0.1
P(pk)
0.10 0.05
0.02
t1
0.01
t2
DUTY CYCLE, D = t1/t2
SINGLE PULSE
0.01
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
t, TIME (s)
Figure 13. Thermal Response
di/dt
IS
trr
ta
tb
TIME
0.25 IS
tp
IS
Figure 14. Diode Reverse Recovery Waveform
http://onsemi.com
6
RθJC(t) = r(t) RθJC
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) - TC = P(pk) RθJC(t)
1.0E+00
1.0E+01
MTD20N06V
PACKAGE DIMENSIONS
DPAK (SINGLE GAUGE)
CASE 369C−01
ISSUE D
A
E
b3
c2
B
Z
D
1
L4
A
4
L3
b2
e
2
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. THERMAL PAD CONTOUR OPTIONAL WITHIN DIMENSIONS b3, L3 and Z.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL
NOT EXCEED 0.006 INCHES PER SIDE.
5. DIMENSIONS D AND E ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY.
6. DATUMS A AND B ARE DETERMINED AT DATUM
PLANE H.
C
H
DETAIL A
3
c
b
0.005 (0.13)
M
H
C
L2
GAUGE
PLANE
C
L
SEATING
PLANE
A1
L1
DETAIL A
ROTATED 905 CW
2.58
0.102
5.80
0.228
3.00
0.118
1.60
0.063
INCHES
MIN
MAX
0.086 0.094
0.000 0.005
0.025 0.035
0.030 0.045
0.180 0.215
0.018 0.024
0.018 0.024
0.235 0.245
0.250 0.265
0.090 BSC
0.370 0.410
0.055 0.070
0.108 REF
0.020 BSC
0.035 0.050
−−− 0.040
0.155
−−−
MILLIMETERS
MIN
MAX
2.18
2.38
0.00
0.13
0.63
0.89
0.76
1.14
4.57
5.46
0.46
0.61
0.46
0.61
5.97
6.22
6.35
6.73
2.29 BSC
9.40 10.41
1.40
1.78
2.74 REF
0.51 BSC
0.89
1.27
−−−
1.01
3.93
−−−
STYLE 2:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
SOLDERING FOOTPRINT*
6.20
0.244
DIM
A
A1
b
b2
b3
c
c2
D
E
e
H
L
L1
L2
L3
L4
Z
6.17
0.243
SCALE 3:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MTD20N06V/D
Similar pages