MUSIC MUAA2K80-20QGC Muaa routing coprocessor (rcp) family Datasheet

Data Sheet
MUAA Routing CoProcessor (RCP) Family
APPLICATION BENEFITS
DISTINCTIVE CHARACTERISTICS
•
High performance MAC Address processor for
multiport switches and routers (Up to 48 10/100 or 4
Gigabit Ethernet at wire speed)
•
2K and 8K x 80-bit partitionable CAM/RAM data
field in address database
•
•
Layer 4 flow recognition for Quality of Service up to
16.7 million packets per second
32-bit synchronous port with separate inputs and
outputs; optional 16-bit configuration
•
•
ARP Cache manager/IP address caching at 12.5
million packets per second
32-bit bi-directional processor port; optional 16-bit
configuration
•
Pipelined operation
•
Synchronous interfaces and programmable priority
between ports for simplicity of design
•
•
Learn, age, and auto-age functions with “virtual
queues,” keeping track of aged and learned entries
Operations performed from the synchronous port or
processor port; all flags independently available to
both ports
•
9-bit internal time stamp
•
Transparent cascade of up to four 2K devices without
external logic, software setup, or performance hit
•
50 MHz clock
•
388-pin PBGA (8K) and 160-pin PQFP (2K)
packages.
•
3.3 Volt core with 3.3 Volt/5 Volt tolerant IO buffers.
•
IEEE 1149.1 (JTAG) compliant
Sync Port
DIN(31:0)
OP(3:0)
/DINE
DINREADY
Processor Port DIN(31:0)
16/32 to 80-bit mux
16/32 to 80-bit mux
80-bit latch
80-bit latch
80-bit 2 to 1 mux
PROCD(31:0)
/FF
/MF
PROCA(5:0)
/PCS
Control
R/W
Address Data Base
-- b i t 79 -- ------- ------- b i t 0---
PROCREADY
Flag and
Chain
Logic
CHAIN
CHAINUP
INT
CHAINDN
/CHAINCS
/RESET
CLK
/OE
Processor Port DOUT(31:0)
/DOUTE
/DOUTVALID
80-bit la tch
80 to 32/16-bit mux
80-bit la tch
80 to 32/16-bit mux
TDI
TCK
TRST
JTAG
TDO
Sync Port
DOUT(31:0)
TMS
Figure 1: Block Diagram
MUSIC Semiconductors, the MUSIC logo, and the phrase "MUSIC Semiconductors" are
Registered trademarks of MUSIC Semiconductors. MUSIC is a trademark of
MUSIC Semiconductors.
March 26, 2003 Rev. 5
MUAA Routing CoProcessor (RCP) Family
General Description
GENERAL DESCRIPTION
Multiple 2K MUAA RCPs may be chained transparently
to provide deeper memory. No software configuration is
necessary. Each MUAA RCP detects where it is in the
chain from the chaining pins on the previous device. A
register is provided to inform the host of the total available
CAM memory and the number of CAMs chained. All
operations to the chained CAM are totally transparent. No
individual device selection or addressing is required.
The MUSIC MUAA Routing CoProcessor (RCP) family
consists of 80-bit wide content-addressable memories
(CAMs), available in depths of 2K and 8K words. The
CAM/RAM associated data partition is programmable
from 32 bits of CAM and 48 bits of associated data, to 80
bits of CAM and 0 bits of RAM. The MUAA RCP can
perform normal routing functions such as search, insert,
and delete on single entries and can age multiple entries
simultaneously. In addition, there is a learn instruction,
particularly useful in networking applications. For
maximum flexibility all the operations may be performed
either through the processor port or through the
synchronous port. Operations may occur on both ports
simultaneously; the port with the highest priority will gain
access first if both ports require a read or write into the
CAM array simultaneously.
The MUSIC MUAA RCP has aging, auto-aging, and
learning functions. All entries have a 9-bit time stamp and
may be marked as static to prevent the aging function from
deleting them. When auto aging is enabled it may be
configured to have higher or lower priority access than the
ports.
Two internal virtual queues of learned and aged entries are
available. As entries are learned or aged out they are
tagged as such and may be read from the device through
either of the ports. This feature enables simple host
management of aged out and learned entries.
The synchronous interface consists of 32-bit wide input
and output ports, both of which may be configured as 16
bits. The data is multiplexed into and out of the CAM and
RAM associated data field. Where input or output data is
wider than the port, it is loaded or unloaded in multiple
cycles starting with the least significant word. Internally
the device is pipelined; once an operation is started on the
synchronous port the next operation may be loaded and the
results of the previous operation unloaded, thus
maximizing device throughput.
IEEE Standard. 1149.1 (JTAG) testability is implemented
providing BYPASS, SAMPLE/PRELOAD, EXTEST,
CLAMP, and HIGH-Z functions.
2
Rev. 5
Pin Descriptions
MUAA Routing CoProcessor (RCP) Family
PIN DESCRIPTIONS
Note: Signal names that start with a slash (“/”) are active LOW. All signals are 3.3 Volt CMOS level. All input and bi-directional pins
are 5-Volt tolerant, except for CLK. Never leave inputs floating except where indicated. The CAM architecture draws large currents
during search operations, mandating the use of good layout and bypassing techniques. Refer to the Electrical Characteristics section
for more information.
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
VCC
DOUT0
GND
DIN31
DIN30
DIN29
DIN28
DIN27
GND
DIN26
DIN25
DIN24
DIN23
DIN22
DIN21
VCC
DIN20
DIN19
DIN18
DIN17
DIN16
DIN15
DIN14
GND
DIN13
DIN12
DIN11
DIN10
DIN9
DIN8
DIN7
VCC
DIN6
DIN5
DIN4
DIN3
DIN2
DIN1
DIN0
GND
See Table 1 for the 388-pin balls and the Packages section for the chip illustrations.
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
160-Pin
PQFP
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
VCC
CH A IND N
CH A INUP
GN D
CH A IN3
CH A IN2
CH A IN1
CH A IN0
GN D
CH AI NCS
PROCD31
PROCD30
PROCD29
PROCD28
PROCD27
PROCD26
PROCD25
PROCD24
VCC
PROCD23
PROCD22
PROCD21
PROCD20
PROCD19
PROCD18
GN D
PROCD17
PROCD16
PROCD15
PROCD14
PROCD13
PROCD12
VCC
PROCD11
PROCD10
PROCD9
PROCD8
PROCD7
PROCD6
GN D
VCC
CLK
GND
/MF
/FF
/DOUTVALID
DINREADY
INT
PROCREADY
TDO
GND
TDI
TMS
TCK
/TRST
/OE
/DOUTE
/DINE
OP0
OP1
OP2
OP3
VCC
PROCA0
PROCA1
PROCA2
PROCA3
PROCA4
PROCA5
R/W
/PCS
/RESET
GND
PROCD0
PROCD1
PROCD2
PROCD3
PROCD4
PROCD5
VCC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GN D
DOUT1
DOUT2
DOUT3
DOUT4
VCC
DOUT5
DOUT6
DOUT7
GN D
DOUT8
DOUT9
DOUT10
DOUT11
VCC
DOUT12
DOUT13
DOUT14
DOUT15
GN D
DOUT16
DOUT17
DOUT18
DOUT19
VCC
DOUT20
DOUT21
DOUT22
DOUT23
GN D
DOUT24
DOUT25
DOUT26
DOUT27
VCC
DOUT28
DOUT29
DOUT30
DOUT31
GN D
Figure 2: 160-Pin PQFP (Top View)
DINREADY (Output)
When DINREADY is HIGH, the synchronous port
accepted the current operation. This is affected by the
priority set for the DIN port and the processor port. Note,
DINREADY may be LOW for up to 800 CLK periods
after /RESET is taken HIGH. The JTAG interface is able
to set DINREADY to HIGH-Z. Active HIGH.
DIN[31:0] (Input)
DIN[31:0] are synchronous port data input pins. Data is
loaded into the MUAA RCP right aligned, least significant
word first.
/DINE (Input)
DIN is sampled by the rising edge of CLK when /DINE is
asserted. Refer to Table 1 for slave connections.
DOUT[31:0] (3-State Output)
DOUT[31:0] is the synchronous port data output. Data is
read out right aligned, least significant word first. The
address index (bits 25–0), SWEX flag (bit 26), PWEX flag
(bit 27), LQUEUE flag (bit 28), AQUEUE flag (bit 29),
Sync Port Match flag (bit 30), and Full flag (bit 31) may
also be read from this port before or after operation data
depending on configuration.
OP[3:0] (Input)
OP[3:0] is a synchronous port operation to be performed
on the data applied to the DIN pins. OP is sampled by the
rising edge of CLK when /DINE is asserted. When loading
the CAM/RAM words to DIN, OP is set to LOAD except
for the last word. OP for the last word is set to the desired
operation.
Rev. 5
3
MUAA Routing CoProcessor (RCP) Family
Pin Descriptions
/DOUTVALID (Output)
/DOUTVALID indicates when new data is available at the
synchronous output port. /DOUTVALID is active LOW
for one CLK cycle. /DOUTVALID may be configured to
become active on the same clock as new DOUT becomes
valid or the CLK before. The JTAG interface is able to set
/DOUTVALID to HIGH-Z.
then get at least one entry again, or another write
exception occurs. The JTAG interface is able to set INT to
HIGH-Z.
/RESET (Input)
The /RESET input is used to reset the MUAA RCP.
/RESET must be asserted for at least 3 CLK periods.
CLK (Input)
The rising edge of CLK input is the device clock.
/OE (Input)
/OE is the DOUT High Impedance control.
/FF (Full Flag, Output)
/FF is active when the device (or chain of devices) is full.
/FF becomes inactive when any one device has two open
entries. The JTAG interface is able to set /FF to HIGH-Z.
/DOUTE (Input)
/DOUTE is the DOUT enable control. When the DOUT
data word is configured to be wider than the output port
then this strobe enables the next word(s) of the DOUT data
onto the DOUT pins.
CHAIN[3:0 (Input)
When two or more devices are chained they communicate
among themselves using the CHAIN[3:0] signals. See
Chaining section. Internally Pulled-up. Refer to Table 1
for slave connections.
PROCD[31:0] (Bi-directional)
The bi-directional Processor data port provides the
processor interface to the device. On write cycles all
devices respond in parallel. On read cycles the appropriate
device responds without additional intervention from the
processor.
CHAINUP (Output)
When two or more devices are chained they communicate
among themselves using the CHAINUP signals. See
Chaining section. The JTAG interface is able to set
CHAINUP to HIGH-Z. Refer to Table 1 for slave
connections.
PROCA[5:0] (Input)
Processor port address bus. Selects which device register
is accessed. Bit 0 is only used when the port is set to 16-bit
mode, otherwise it should be held at a valid logic level.
CHAINDN (Output)
When two or more devices are chained they communicate
among themselves using the CHAINDN signals. See
Chaining section. The JTAG interface is able to set
CHAINDOWN to HIGH-Z. Refer to Table 1 for slave
connections.
R/W (Input)
R/W is the processor port read/write control pin. This pin
is HIGH for reads, LOW for writes.
/PCS (Input)
/PCS is the processor port chip select pin. When LOW this
pin indicates a cycle to the processor port. On write cycles
data must be set up to the rising edge of /PCS. On read
cycles /PCS controls the output enable of the PROCD bus.
Note that /PCS may be asynchronous to CLK. Refer to
Table 1 for slave connections.
CHAINCS (Bi-directional)
When two or more devices are chained they communicate
among themselves using the CHAINCS signals. See
Chaining section. Internally pulled up. Refer to Table 1 for
slave connections.
PROCREADY (Output)
When PROCREADY is HIGH, indicates the processor
read data is available or the processor write data is
accepted. Priority may be set between the DIN port and
the processor port. Note PROCREADY may be LOW for
up to 800 CLK periods after /RESET is taken HIGH. The
JTAG interface is able to set PROCREADY to HIGH-Z.
/MF (Match Flag, Output)
The /MF output indicates whether a match was found. The
JTAG interface is able to set /MF to HIGH-Z.
/TRST (JTAG Reset, Input)
The /TRST is the Test Reset pin. Internally pulled up with
25K minimum. Must be tied to /RESET or tied LOW
when not in use.
INT (Output)
INT interrupt. Indicates the aged or learned queue has at
least one entry or a write exception occurred. The service
routine should either check the AQUEUE, LQUEUE, and
WEX registers, or bits 26–29 of the Address Index
register, to determine the cause. The interrupt is cleared
after the appropriate flag register has been read and will
not be reasserted until either the queue(s) are emptied and
/TCLK (JTAG Test Clock, Input)
The /TCLK input is the Test Clock input. Must be tied at a
valid logic level when not in use.
TMS (JTAG Test Mode Select, Input)
The TMS input is the Test Mode Select input. Internally
pulled up with 25K minimum.
4
Rev. 5
Pin Descriptions
MUAA Routing CoProcessor (RCP) Family
VCC, GND
These pins are the power supply connection to the MUAA
RCP. VCC must meet the voltage supply requirements in
the Operating Conditions section relative to the GND pins,
which are at 0 Volts (system reference potential), for
correct operation of the device. All the ground and power
pins must be connected to their respective planes with
adequate bulk and high frequency bypassing capacitors in
close proximity to the device.
TDI (JTAG Test Data Input, Input)
The TDI input is the Test Data input. Internally pulled up
with 25K minimum. Refer to Table 1 for slave
connections.
TDO (JTAG Test Data Output, Output)
The TDO output is the Test Data output. Refer to Table 1
for slave connections.
Ball Descriptions
Table 1: Ball Descriptions
Functional
Group
Ball Name(s)
Synchronous
Input Port
DIN[31:0]
PBGA Ball(s)
Input
5V tol
b0:AA26, b1:AA25, b2:Y26,
b3:Y25, b4:W26, b5:W25,
b6:V26, b7:V25, b8:U26,
b9:U25, b10:T26, b11:T25,
b12:R26, b13:R25, b14:P26,
b15:P25, b16:N26, b17:N25,
b18:M26, b19:M25, b20:L26,
b21:L25, b22:K26, b23:K25,
b24:J26, b25:J25, b26:H26,
b27:H25, b28:G26, b29:G25,
b30:F26, b31:F25
When asserted, DIN is sampled by the rising edge of
CLK. Connect to T2, R2, and P2.
Input
5V tol
T1
/DINE-S1
Slave 1. Connect to T1, /DINE.
Input
5V tol
T2
/DINE-S2
Slave 2. Connect to T1, /DINE.
Input
5V tol
R2
/DINE-S3
Slave 3. Connect to T1, /DINE.
Input
5V tol
P2
Synchronous port operation performed on data
applied to DIN pins.
Input
5V tol
b0:U1, b1:U2, b2:U3, b3:T3
When HIGH, indicates the synchronous port
accepted the current operation.
Output
H1
OP[3:0]
DINREADY
CLK
Rising edge is the device clock.
DOUT[31:0]
Synchronous port data output.
Output
b0:A21, b1:B21, b2:A20,
b3:B20, b4:A19, b5:B19,
b6:A18, b7:B18, b8:A17,
b9:B17, b10:A16, b11:B16,
b12:A15, b13:B15, b14:A14,
b15:B14, b16:A13, b17:B13,
b18:A12, b19:B12, b20:A11,
b21:B11, b22:A10, b23:B10,
b24:A9, b25:B9, b26:A8,
b27:B8, b28:A7, b29:B7,
b30:A6, b31:B6
/DOUTVALID
Indicates when new data is available at the
synchronous output port.
Output
G1
DOUT high impedance control.
Input
5V tol
P1
DOUT enable control.
Input
5V tol
R1
Match flag. Indicates if a match was found.
Output
E1
/OE
/DOUTE
/MF
Rev. 5
Type
Synchronous port data input.
/DINE
Synchronous
Output Port
Function
5
Input
D1
3.3V only
MUAA Routing CoProcessor (RCP) Family
Pin Descriptions
Table 1: Ball Descriptions (continued)
Functional
Group
Ball Name(s)
Processor Port
PROCD[31:0]
Processor port data.
Bidir
5V tol
b0:AB1, b1:AB2, b2:AC1,
b3:AC2, b4:AF3, b5:AE3,
b6:AF4, b7:AE4, b8:AF5,
b9:AE5, b10:AF6, b11:AE6,
b12:AF7, b13:AE7, b14:AF8,
b15:AE8, b16:AF9, b17:AE9,
b18:AF10, b19:AE10,
b20:AF11, b21:AE11,
b22:AF12, b23:AE12,
b24:AF13, b25:AE13,
b26:AF14, b27:AE14,
b28:AF15, b29:AE15,
b30:AF16, b31:AE16
PROCA[5:0]
Processor port address bus.
Input
5V tol
b0:W1, b1:W2, b2:W3, b3:Y1,
b4:Y2, b5:Y3
R/W
Processor port read/write control
Input
5V tol
V2
/PCS
Processor port chip select. Connect to AA2, AA3,
and AB3.
Input
5V tol
AA1
/PCS-S1
Slave 1. Connect to AA1, /PCS.
Input
5V tol
AA2
/PCS-S2
Slave 2. Connect to AA1, /PCS.
Input
5V tol
AA3
/PCS-S3
Slave 3. Connect to AA1, /PCS.
Input
5V tol
AB3
When HIGH, indicates the processor read data is
available or the processor write data is accepted.
Output
K1
INT interrupt. Indicates the aged or learned queue
has at least one entry or a write exception occurred.
Output
J1
Resets the MUAA RCP.
Input
5V tol
V1
Full flag. Active when the device (or chain of devices)
is full
Output
F1
PROCREADY
INT
/RESET
/FF
Function
6
Type
PBGA Ball(s)
Rev. 5
Pin Descriptions
MUAA Routing CoProcessor (RCP) Family
Table 1: Ball Descriptions (continued)
Functional
Group
Ball Name(s)
Cascade
CHAIN0
NC. For MUSIC production test only.
Input
AF18
CHAIN1
Internal chaining. Connect to AE19, CHAINUP-S1.
Input
AF19
CHAIN2
Internal chaining. Connect to AE20, CHAINUP-S2.
Input
AF20
CHAIN3
Internal chaining. Connect to AE21, CHAINUP-S3.
Input
AF21
CHAIN0D
Internal chaining. Connect to AF23, CHAINDN.
Input
AE22
CHAIN1D
Internal chaining. Connect to AE23, CHAINDN-S1.
Input
AD22
CHAIN2D
Internal chaining. Connect to AD23, CHAINDN-S2.
Input
AC22
CHAINUP
Rev. 5
PBGA Ball(s)
NC. For MUSIC production test only.
Output
AF22
Internal chaining. Connect to AF19, CHAIN1.
Output
AE19
CHAINUP-S2
Internal chaining. Connect to AF20, CHAIN2.
Output
AE20
CHAINUP-S3
Internal chaining. Connect to AF21, CHAIN3.
Output
AE21
CHAINDN
Internal chaining. Connect to AE22, CHAIN0D.
Output
AF23
CHAINDN-S1
Internal chaining. Connect to AD22, CHAIN1D.
Output
AE23
CHAINDN-S2
Internal chaining. Connect to AC22, CHAIN2D.
Output
AD23
NC. For MUSIC production test only.
Output
AC23
Internal chaining. Connect to AE17, AD17, and
AC17.
Bidir
AF17
CHAINCS-S1
Internal chaining. Connect to AF17.
Bidir
AE17
CHAINCS-S2
Internal chaining. Connect to AF17.
Bidir
AD17
CHAINCS-S3
Internal chaining. Connect to AF17.
Bidir
AC17
CHAIN1X
NC. For MUSIC production test only.
Input
AE18
CHAIN2X
NC. For MUSIC production test only.
Input
AD18
CHAIN3X
NC. For MUSIC production test only.
Input
AC18
/TRST
Test reset.
Input
N3
TCLK
Test clock input.
Input
N2
N1
CHAINCS
Power
Type
CHAINUP-S1
CHAIND-S3
JTAG
Function
TMS
Test mode select.
Input
TDI
Test data input.
Input
M1
TDI-A
Internal JTAG chain. Connect to L2, TDO-A.
Input
M2
M3
TDI-B
Internal JTAG chain. Connect to L3, TDO-B.
Input
TDI-C
Internal JTAG chain. Connect to L3, TDO-C.
Input
M4
TDO
Test data output.
Output
L1
TDO-A
Internal JTAG chain. Connect to M2, TDI-A.
Output
L2
TDO-B
Internal JTAG chain. Connect to M3, TDI-A.
Output
L3
TDO-C
Internal JTAG chain. Connect to M4, TDI-A.
Output
L4
3.3V
Device power, 3.3 volts.
N/A
7
AD7, AD8, AD13, AD14, AD19,
AD20, AC7, AC8, AC13, AC14,
AC19, AC20, Y4, Y23, Y24, W4,
W23, W24, R3, R4, R12, R13,
R14, R15, P3, P4 P12, P15,
P23, P24, N12, N15, N23, N24,
M12, M13, M14, M15, H23,
H24, G23, G24, D6, D7, D10,
D11, D15, D16, D20, D21, C6,
C7, C10, C11, C15, C16, C20,
C21
MUAA Routing CoProcessor (RCP) Family
Operational Characteristics
Table 1: Ball Descriptions (continued)
Functional
Group
Ball Name(s)
Ground
GND
Function
Device ground.
Type
PBGA Ball(s)
N/A
AF1, AF2, AF24, AF25, AF26
AE1, AE2, AE24, AE25, AE26
AD1–AD6, AD9– AD12, AD15,
AD16, AD21, AD24, AD25,
AD26, AC3–AC6, AC9–AC12
AC15, AC16, AC21,
AC24–AC26, AB4, AB23–AB26,
AA4, AA23, AA24, V3, V4, V23,
V24, U4, U23, U24, T4,
T11–T16, T23, T24, R11, R16,
R23, R24, P11, P13, P14, P16,
N4, N11, N13, N14, N16, M11,
M16, M23, M24, L11–L16, L23,
L24, K23, K24 J23, J24, F23,
F24, E23–E26, D2–D5, D8, D9,
D12–D14, D17–D19, D22–D26,
C1–C5, C8, C9, C12–C14,
C17–C19, C22– C26, B1–B5,
B22–B26, A1–A5, A22–A26
OPERATIONAL CHARACTERISTICS
Loading and Unloading
In order to keep data alignment simple, the number of
words to be loaded and unloaded for each operation is kept
consistent for each CAM/RAM partition configuration and
the width of the port.
Depending on the operation, unloads either start from the
right aligned, least significant word of CAM followed by
the right aligned, least significant word of RAM or just
from the right aligned, least significant word of RAM. For
instance, a QUEUE read returns CAM then RAM,
whereas a search just returns RAM. Where the
CAM/RAM partition does not lie on a port width
boundary the last word of the read may contain undefined
data in the most significant bits. The number of unload
cycles actually completed is optional.
Tables 2 and 3 show the cycle sequence and CAM/RAM
bit mappings for 32- and 16-bit bus modes. The bus may
be selected for each port independently. Table 4 shows
whether CAM, RAM or both types of segments are used
on input or output cycles for each operation.
The DOUT register stores the results of operations from
the asynchronous processor port. Search results are
obtained by repeated reads of DOUT until all RAM data is
read. When performed from the processor port, READ
LQUEUE and READ AQUEUE return the first segment
of CAM data on the cycle that requests the operation;
additional CAM and RAM segments are obtained by
repeated reads of the DOUT register.
Loads always start right aligned from the least significant
word, CAM partition first, followed by RAM if necessary.
Most instructions do not require the entire 80 bits to be
loaded.
CAM data is required as an input for all operations except
READ LQUEUE and READ AQUEUE. The use of RAM
data is optional (i.e., it is not necessary to perform all
RAM cycles when inputting data). However, the user must
be aware that INSERT and LEARN operations will
over-write RAM data. Therefore, the application should
remain consistent in the number of RAM bits used for
these operations.
Loading is flow controlled on the synchronous DIN port
with the DINREADY signal, which is HIGH when data is
accepted by the DIN port. On the Processor port the
PROCREADY signal is HIGH when the current write
cycle may complete.
All CAM and RAM segment writes except the last use the
LOAD instruction. The last segment of data uses the
instruction for the desired operation.
8
Rev. 5
Operational Characteristics
MUAA Routing CoProcessor (RCP) Family
Operations
On the synchronous port, operations are started on the
CLK cycle in which the requested Op-Code is written. On
the processor port operations are started when the chosen
operation register is written. The user should use the flow
control mechanisms to determine when results are
available. On the synchronous port the /DOUTVALID
signal is asserted for one CLK cycle when new data is
written to the DOUT port. The processor port will assert
its PROCREADY signal on the CLK edge that data is
available. Note that there is no internal flow control from
the sync DOUT port back to the sync DIN port. The
DOUT data is overwritten if it is not unloaded.
Table 2: 32-Bit Bus Mode CAM/RAM Cycles by Partition Configuration
Cycle
No RAM 79:0 CAM
79:64 RAM 63:0 CAM
79:48 RAM 47:0 CAM
1
CAM[31:0]
CAM[31:0]
CAM[31:0]
79:32 RAM 31:0 CAM
CAM[31:0]
2
CAM[63:32]
CAM[63:32]
CAM[47:32]*
RAM[63:32]
3
CAM[79:64]*
RAM[79:64]*
RAM[79:48]
RAM[79:64]*
Note: *Bus bits [15:0] contain data. Bus bits [31:16] are undefined.
Table 3: 16-Bit Bus Mode CAM/RAM Cycles by Partition Configuration
Cycle
No RAM 79:0 CAM
79:64 RAM 63:0 CAM
79:48 RAM 47:0 CAM
1
CAM[15:0]
CAM[15:0]
CAM[15:0]
79:32 RAM 31:0 CAM
CAM[15:0]
2
CAM[31:16]
CAM[31:16]
CAM[31:16]
CAM[31:16]
3
CAM[47:32]
CAM[47:32]
CAM[47:32]
RAM[47:32]
4
CAM[63:48]
CAM[63:48]
RAM[63:48]
RAM[63:48]
5
CAM[79:64]
RAM[79:64]
RAM[79:64]
RAM[79:64]
Table 4: Input and Output CAM/RAM Cycles by Operation
Operation
DIN, PROCD (Write)
INSERT
CAM & RAM
N/A
SEARCH
CAM only
RAM only
SEARCHA
CAM only
RAM only
LEARN
CAM & RAM
N/A
DELETE
CAM only
N/A
READ LQUEUE
N/A
CAM & RAM
READ AQUEUE
N/A
CAM & RAM
Device Chaining
Up to four MUAA 2K RCPs may be chained with no
external logic. Figure 3 shows the interconnection. Unused
CHAIN[3:0] pins should be left unconnected.
Where device pins are paralleled, attention should be paid
to signal integrity, in particular to signals used for
clocking, i.e., CLK, /PCS. PCB layout techniques such as
daisy chaining and driver to track impedance matching
should be observed.
The /MF, /FF, INT, DOUTVALID, DINREADY, and
PROCREADY signals should only be used on the master
device and left disconnected on the slave devices. The
master device is the one with no connection to the
CHAINUP pin.
Rev. 5
DOUT, PROCD (Read)
The scheme in Figure 3 allows devices to be designed in
but not fitted. The fit order would be MASTER, SLAVE1,
SLAVE2, SLAVE3.
9
MUAA Routing CoProcessor (RCP) Family
Operational Characteristics
DINREADY
/DOUTVALID
PROCREADY
DIN(31:0)
DINE
OP(3:0)
DOUT(31:0)
/OE
/DOUTE
INT
/FF
/MF
MASTER
CHAIN(0)
CHAIN(1)
CHAIN(2)
CHAIN(3)
PROCD(31:0)
PROCA(5:0)
R/W
/PCS
CLK
/RESET
CHAINCS
CHAINUP
CHAINDN
DIN(31:0)
DINE
CHAIN(0)
CHAIN(1)
CHAIN(2)
CHAIN(3)
OP(3:0)
DOUT(31:0)
/OE
/DOUTE
SLAVE 1
PROCD(31:0)
PROCA(5:0)
R/W
/PCS
CLK
/RESET
CHAINCS
CHAINUP
CHAINDN
DIN(31:0)
DINE
OP(3:0)
DOUT(31:0)
/OE
/DOUTE
SLAVE 2
CHAIN(0)
CHAIN(1)
CHAIN(2)
CHAIN(3)
PROCD(31:0)
PROCA(5:0)
R/W
/PCS
CLK
/RESET
CHAINCS
CHAINUP
CHAINDN
DIN(31:0)
DINE
OP(3:0)
DOUT(31:0)
/OE
/DOUTE
SLAVE 3
CHAIN(0)
CHAIN(1)
CHAIN(2)
CHAIN(3)
PROCD(31:0)
PROCA(5:0)
R/W
/PCS
CLK
/RESET
CHAINCS
CHAINUP
CHAINDN
Figure 3: Device Chaining (2K only)
10
Rev. 5
Operational Characteristics
MUAA Routing CoProcessor (RCP) Family
Interrupts
There are four sources of interrupts that will cause the INT
pin to be asserted: AQUEUE, LQUEUE, SWEX, and
PWEX. The appropriate enables must be set in the
Configuration register to enable the interrupts.
status. The user may qualify reads from AQUEUE and
LQUEUE with the appropriate ports match flag that will
be asserted if the data is valid.
SWEX and PWEX
SWEX and PWEX interrupts are set when a write
exception condition occurs. This occurs when two Write
cycles are pending in the device and there is only one
space left.
The interrupt service routine should read the appropriate
flag registers to determine the interrupt cause. The flags
are available individually or from the Address Index
register. The appropriate individual flag register must be
read in order to acknowledge the interrupt.
The SWEX and PWEX flags indicate which port caused
the exception and which are available individually to the
processor. Both processor write exceptions are available in
the processor Address index port and the DOUT port
Address index word.
LQUEUE and AQUEUE
AQUEUE and LQUEUE interrupts are set by an entry
being written into one or another of the queues. When the
flag register is read the interrupt is acknowledged. The
processor may read the LQUEUE and AQUEUE flags to
determine when all the entries are read from the
appropriate queue. The interrupt will not be reasserted
until a queue has been emptied and then gets another entry.
Note that it is possible for learned entries to be aged and
aged entries to be learned. If this occurs the AQUEUE and
LQUEUE flags may be set for an entry that has changed
JTAG
Please refer to IEEE Standard 1149.1 for information on
using the JTAG functions. See Table 5 for JTAG functions.
A BSDL file is available; check the MUSIC
Semiconductors website or contact MUSIC Technical
Support.
Table 5: JTAG Functions
ID
Binary
JTAG Codes
0011
1010
1010
0000
HEX
3
A
A
0
Description
Version
MUAA
0010
0001
2
1
2K
0011
3
3
MANUF ID
Typical Example
This typical example shows the cycles that the MUAA
RCP would perform in a multiport switch. The
CAM/RAM partition is set to 48 bits CAM, 32 bits RAM.
Both the processor port and the synchronous port are 32
bits wide. The index and flags are programmed to be the
last word out of the DOUT port. The synchronous port has
priority. The LQUEUE and AQUEUE are enabled. The
CAM partition is used to store 48-bit MAC addresses and
the RAM partition used to store associated data to the
MAC address such as switch port and VLAN numbers.
EXT TEST
0000
BYPASS
1111
SAMPLE
0001
ID CODE
0010
CLAMP
0100
HIGH-Z
0011
CLK periods to complete. Due to the internal design of the
MUAA RCP, pipelining is possible; therefore, further
operations can be performed while the DA search is being
done internally.
Sync Port cycle2 is a learn on a frame SA (Source
address). At CLK3 the first word of CAM is loaded, at
CLK4 the second word is loaded (most significant 16 bits
discarded). At CLK5 the learn instruction is given along
with the word of RAM data that would contain the port ID
and other data associated with the SA.
At CLK6 the results of the search instruction issued in
cycle1 are available at the DOUT bus of the synchronous
port, as indicated by /DOUTVALID going active for a
CLK. The result of this cycle was a no-match condition as
/MF was not asserted LOW. Because the cycle was a DA
search and there was a no-match result, there will be no
data available on the DOUT bus. Typically in this situation
a switch would forward the frame to all ports or all ports
on the same VLAN.
Sync Port Cycle 1 is a search to lookup the port associated
with a frame DA (Destination address). At CLK1 the first
word (32 bits) of CAM search word is loaded. At CLK2
the last 16 bits of CAM search word is loaded and the
instruction “search” given. The most significant 16 bits of
the second word are discarded as the CAM partition is 48
bits wide. The results from the DA search will not be
available until CLK6 because the operation takes three
Rev. 5
0011
11
MUAA Routing CoProcessor (RCP) Family
Operational Characteristics
PROCREADY signal is asserted immediately once the
cycle is initiated. The processor may use the LQUEUE
data to maintain a management database of MAC
addresses and associated port IDs.
Sync Port cycle3 starts at CLK8, which is the DA search
of the next frame.
AT CLK 10 the results of the cycle2 learn operation are
available. /MF was not asserted LOW; therefore the 48-bit
CAM partition data was not found during the compare.
The MUAA RCP automatically writes the 80-bit
CAM/RAM word into the next free location of the
memory array along with the most up to date time stamp
or entry life. The address index is available from the
DOUT bus to indicate where in the memory array the data
was placed. This can be used to implement further
associated data in software or hardware. Furthermore, the
INT output is asserted to indicate that the “learned” word
was entered into the LQUEUE.
Back to back DA searches are shown from CLK25
onward. This is to demonstrate how the synchronous port
handshaking works using the /DINREADY output. Sync
port cycle5 and cycle6 are completed normally but at
CLK29 /DINREADY goes LOW to indicate that the
MUAA RCP cannot accept the load operation of sync
cycle7. Therefore the host must hold the DIN, OP, and
DINE signals active until /DINREADY goes HIGH. At
this point the MUAA RCP will return /DINREADY to
HIGH to indicate that it has accepted the DIN and OP
information.
Sync Port cycle4, which is the SA learn of the same frame
as Sync Port cycle3, is initiated at CLK10.
The processor can also be used to access the MUAA RCP
for general housekeeping duties. The LQUEUE contains
the contents of the virtual learned queue. A processor
cycle is started around CLK12 to read the LQUEUE
register. This cycle is unable to be completed because the
CAM core is busy servicing the synchronous port.
PROCREADY remains inactive to inform the processor of
the delay. The cycle is therefore extended and will
complete when the MUAA RCP asserts PROCREADY
HIGH.
/MF is asserted LOW to indicate a match result on the
CAM partition compare. At this point DOUT will be used
to transfer the associated data and the address index of the
matching condition. The associated data is available first
(RAM partition) and would normally contain the port ID
in a typical switch. The RAM partition is configured as 32
bits wide and can therefore be transferred in one CLK
period. /DOUTE is asserted by the user to transfer the next
word of data on the next clock period. As the RAM takes
only one cycle, the address index is available after the
associated data.
The result of cycle4, which was a SA learn, is available at
CLK17. The learn instruction produced a match result.
There was no need to overwrite the CAM/RAM partitions,
but the MUAA RCP automatically updated the time stamp
or entry life of the matching entry. The address index of
the entry becomes available at the DOUT port.
The processor cycle data requested earlier, can now
become available at CLK21. PROCREADY is asserted
HIGH by the device to indicate that the cycle may be
completed. The first 32-bit word is available on the
PROCD bus and can be read by the processor. The two
remaining 32-bit words that complete the LQUEUE entry
are read by the subsequent processor cycles. These cycles
do not require access to the CAM core, hence the
12
Rev. 5
Rev. 5
13
Figure 4: Example Sequence
PROCREADY
R/W
PROCA(5:1)
PROCD(31:0)
/PCS
INT
/OE
/DOUTE
/DOUTVALID
DOUT(31:0)
/MF
DINREADY
OP(3:0)
DIN(31:0)
/DINE
CLK
load1
cam1
1
cam2
3
search1 load2
cam1
2
load2
cam2
4
learn2
ram2
5
valid1
no match 1
6
7
load3
cam3
8
cam4
10
cam4
12
learn4
lqueue addr
learn 2 in queue
valid2
load4
cam4
11
index2
no match 2
search3 load4
cam3
9
valid3
ram3
match 3
13
14
index3
15
16
valid4
index4
match 4
17
18
20
22
cam2 lqueue
21
23
24
26
search
5
cam5
lqueue addr
load5
cam5
25
load6
cam6
27
lqueue cam2
search
6
cam6
28
30
valid5
ram5
match 5
load7
cam7
29
32
33
valid6
34
search
8
cam8
35
lqueue ram2
no match 6
load8
cam8
lqueue addr
index5
search
7
cam7
31
valid7
no match 7
36
37
Operational Characteristics
MUAA Routing CoProcessor (RCP) Family
MUAA Routing CoProcessor (RCP) Family
Instruction Set Descriptions
INSTRUCTION SET DESCRIPTIONS
Mnemonic: age
Binary Op-Code: 7 CLKS: 3
Function: If the aged virtual queue is disabled: This
instruction will remove all entries whose life has expired
and are not marked as permanent. Removed entries will
not participate in future searches. If the aged virtual queue
is enabled: This instruction will move all entries whose
life has expired to the aged virtual queue. If a learn
instruction matches the CAM partition of an entry in the
aged virtual queue, the entry is moved to the learned
virtual queue and the new RAM data written.
Mnemonic: NOOP
Binary Op-Code: 0 CLKS: 3
Function: No operation.
Mnemonic: load<DIN>
Binary Op-Code: 1 CLKS: 1
Function: Load a word of the DIN data, starting with the
least significant word. This instruction is applied to all
words loaded into the DIN port except the last word. The
last word is loaded with the Op-Code of the operation to
be performed. Refer to the Loading and Unloading
section.
Mnemonic: clear
Binary Op-Code: 8 CLKS: 3
Function: Reset array to empty.
Mnemonic: insert<DIN>
Binary Op-Code: 2 CLKS: 4
Function: Write DIN into the CAM/RAM. If data exists
in the CAM partition already, the RAM partition will be
overwritten with the new RAM partition data. The entry
will be marked as permanent. The address index may be
read from the output ports. See Note 1 regarding write
exception.
Mnemonic: clear LQUEUE
Binary Op-Code: 9 CLKS: 3
Function: Delete the contents of the learned virtual
queue. The entry will not generate a match on a SEARCH
or SEARCHA operation.
Mnemonic: clear AQUEUE
Binary Op-Code: 10 CLKS: 3
Function: Delete the contents of the aged virtual queue,
if enabled.
Mnemonic: search<DIN>
Binary Op-Code: 3 CLKS: 3
Function: Search for data in the CAM partition of DIN.
If data is found the match flag is asserted and RAM data
will appear at DOUT. The address index and flags may
also be read.
Mnemonic: read LQUEUE
Binary Op-Code: 11 CLKS: 3
Function: Read the next learned queue entry. Entries are
returned in internal priority order, lowest address first, not
in the order they were written. The address index may be
read. Note that entries do not have to be read from the
LQUEUE if deemed unnecessary. The device treats
learned entries as if they are valid entries.
Mnemonic: searcha<DIN>
Binary Op-Code: 4 CLKS: 4
Function: Search for data in the CAM partition of DIN.
If data is found the match flag is asserted and RAM data
will appear at DOUT and the age of the entry is updated.
The address index and flags may also be read.
Mnemonic: learn<DIN>
Binary Op-Code: 5 CLKS: 4
Function: Search for data in the CAM partition of DIN.
If data is found, the match flag is asserted and the RAM
partition written. The address index may be read. Update
the age. If data is not found, write the CAM and RAM
partitions to the next free address. The address index may
be read. See Note 1 regarding write exception.
Mnemonic: read AQUEUE
Binary Op-Code: 12 CLKS: 4
Function: This instruction is available only if the
AQUEUE is enabled. Read the next aged queue entry.
Entries are returned in internal priority order, lowest
address first, not in the order they were written. The
address index may be read.
Mnemonic: delete<DIN>
Binary Op-Code: 6 CLKS: 3
Function: Search for data on the CAM partition of DIN.
If data is found delete the data. The address index may be
read.
1.
Notes:
2.
14
Due to the pipelined nature of the device, it is possible for a write
cycle to be pending (learn or insert) when the device is full. A write
exception interrupt will indicate when this occurs if enabled. See
Interrupt section.
There is one CLK of latency to start the pipe on the synchronous
port. The number of CLKs per instruction assumes the pipe is kept
full and indicates throughput.
Rev. 5
Instruction Set Descriptions
MUAA Routing CoProcessor (RCP) Family
Processor Port Registers
Table 6: Processor Port Registers
PROCA[5:0]
Bit(s)
NOOP
Register/Instruction
0x00
31:0 W
Function
NOOP operation
load<DIN>
0x02
31:0 W
Perform load operation.
insert<DIN>
0x04
31:0 W
Perform insert operation.
search<DIN>
0x06
31:0 W
Perform search operation.
searcha<DIN>
0x08
31:0 W
Perform searcha operation.
learn<DIN>
0x0A
31:0 W
Perform learn operation.
delete<DIN>
0x0C
31:0 W
Perform delete operation.
age
0x0E
N/A W
Age MUAA RCP contents.
clear
0x10
N/A W
Perform clear operation.
clear LQUEUE
0x12
N/A W
Perform clear LQUEUE operation.
Perform clear AQUEUE operation.
clear AQUEUE
0x14
N/A W
read LQUEUE
0x16
31:0 R
Read LQUEUE data.
read AQUEUE
0x18
31:0 R
Read AQUEUE data.
DOUT
0x1A
31:0 R
After an operation has been performed on the processor port the output data may be read and unloaded from this port. Data is read right
aligned least significant word first.
CONFIGURATION
0x20
0 R/W
Processor port width. If set to 16-bit mode the most significant 16 bits
of each register are addressed by bit 0 of the address pins. After reset,
the Configuration register must be written before any other, 0 = 32-bit,
1 = 16-bit. Resets to 0.
1 R/W
Sync port input width. 0 = 32-bit; 1 = 16-bit. Resets to 0.
2 R/W
Sync port output width. 0 = 32-bit; 1 = 16-bit. Resets to 0.
4:3 R/W
5 R/W
6:7 R/W
CAM/associated data partition point
0 = 79:0 CAM
1 = 79:64 RAM 63:0 CAM
2 = 79:48 RAM 47:0 CAM
3 = 79:32 RAM 31:0 CAM
Resets to 0
DOUTVALID Timing. 0 = Same CLK as Data; 1 = 1 CLK before Data.
Resets to 0.
Reserved. Write 0.
8 R/W
INT active HIGH or active LOW. 0 = LOW; 1 = HIGH. Resets to 1.
9 R/W
Enable LQUEUE interrupt. 0 = Disable; 1 = Enable. Resets to 0.
10 R/W
Enable AQUEUE interrupt. 0 = Disable; 1 = Enable. Resets to 0.
11 R/W
Enable PWEX interrupt. 0 = Disable; 1 = Enable. Resets to 0.
12 R/W
Enable SWEX interrupt. 0 = Disable; 1 = Enable. Resets to 0.
13 R/W
Enable auto-aging function. 0 = Disable; 1 = Enable. Resets to 0.
14 R/W
Enable AQUEUE queue. 0 = Disable; 1 = Enable; Resets to 0. Note
that LQUEUE is always enabled.
15 R/W
Set port priority. 0 = Sync port; 1 = Processor port. Resets to 0.
16 R/W
Reserved. Write 0.
17 R/W
Set Sync DOUT port address index first read or last read. 0 = Last,
1 = First. Resets to 0.
18 R/W
1 = Auto age highest-priority; 0 = lowest-priority. Resets to 0. Only if
auto-aging is on.
31:19 R/W
Reserved. Write 0.
MF
0x22
0R
Indicates the Processor port got a match on the last operation.
1 = Match, 0 = No Match.
FF
0x24
0R
Full flag. Indicates when the device has one or zero free entries left.
1 = Full, 0 = Not Full.
Rev. 5
15
MUAA Routing CoProcessor (RCP) Family
Instruction Set Descriptions
Table 6: Processor Port Registers (continued)
Register/Instruction
Address Index
PROCA[5:0]
Bit(s)
Function
0x26
25:0 R
Once an operation has been performed on the Processor port the
address index is available here. Useful as an index for associated
tables in software.
26 R
SWEX flag
27 R
PWEX flag
28 R
LQUEUE flag
29 R
AQUEUE flag
30 R
Processor Port Match flag; 1 = Match
31 R
Full flag; 1 = Full
LQUEUE Flag
0x28
0R
Indicates the LQUEUE has at least one entry. Note this bit is available
even if the INT pin is disabled. A read clears the interrupt.
AQUEUE Flag
0x2A
0R
Indicates the AQUEUE has at least one entry. Note this bit is available
even if the INT pin is disabled. A read clears the interrupt.
PWEX Flag
0x2C
0R
Indicates a write exception condition has occurred on the processor
port. A read clears the interrupt.
SWEX Flag
0x2E
0R
Indicates a write exception condition has occurred on the syncport. A
read clears the interrupt.
Auto-Age Interval
0x30
31:0 R/W
When auto-aging is enabled the CLK is divided by the value in this register to provide the auto-age interval. Resets to 02FAF080h = 1 second
with 50 MHz CLK.
Learned Entry Life
0x32
8:0 R/W
This register sets the life of a learned entry in units of the auto-age
Interval register. Resets to 012Ch = 300.
Info
0x34
1:0 R
2R
Number of cascaded devices
Read 0
31:3 R
Device ID. 1 = MUAA RCP.
Size
0x36
31:0 R
Chain size. Multiples of 0.25K
Revision
0x38
3:0 R
Master Device Rev.
7:4 R
Slave 1 Rev.
11:8 R
Slave 2 Rev.
15:12 R
Slave 3 Rev.
31:16 R
Read 0
16
Rev. 5
Electrical
MUAA Routing CoProcessor (RCP) Family
ELECTRICAL
Absolute Maximum Ratings
Supply Voltage
-0.5 to 4.6 Volts
Voltage on All Other Pins
-0.5 to VCC+0.5 Volts (-2.0 Volts for
10 ns, measured at the 50% point)
Temperature
-40°C to 85°C
Stresses exceeding those listed under Absolute
Maximum Ratings may induce failure. Exposure to
absolute maximum ratings for extended periods may
reduce reliability. Functionality at or above these
conditions is not implied.
Storage Temperature
-55°C to 125°C
All voltages referenced to GND.
DC Output Current
20 mA (per output, one at a time, one second
duration)
Operating Conditions
Symbol
Parameter
Min.
Typical
Max.
Units
3.3
3.6
Volts
Notes
VCC
Operating supply voltage
3.0
VIH
Input voltage logic 1
2.0
5.5
Volts
All other pins
2.4
VDD + 0.3
Volts
CLK
-0.3
0.8
Volts
0
70
°C
Typical
Max.
Units
310
400
mA
MUAA2K
1.25
1.6
A
MUAA8K
2
7
mA
VIL
Input voltage logic 0
TA
Ambient operating temperature
Still air
Electrical Characteristics
Symbol
ICC
ICC(SB)
Parameter
Min.
Average power supply current
Stand-by power supply current
VOH
Output voltage logic 1
VOL
Output voltage logic 0
IIZ
Input leakage current
IOZ
Output leakage current
IRP
Input pull-up resistors
2.4
Notes
Volts
IOH = -8.0 mA
0.4
Volts
IOL = 8.0 mA
-2
2
µA
VSS ≤ VIN ≤ VCC
-10
10
µA
VSS ≤ VOUT ≤ VCC
/TRST, TMS, TDI
MUAA2K
25
KΩ
MUAA8K
6.25
KΩ
Capacitance
Symbol
CIN
COUT
Rev. 5
Parameter
Input capacitance
Output capacitance
Max.
Units
MUAA2K
6
pF
MUAA8K
45
pF
MUAA2K
7
pF
MUAA8K
45
pF
17
Notes
f = 1 MHz, VIN = 0V
f = 1 MHz, VOUT = 0V
MUAA Routing CoProcessor (RCP) Family
Timing Diagrams
TIMING DIAGRAMS
t16A
t2
t8
t1
t16B
t12
t16
t13
t9
CLK
/DINE
DIN(31:0)
Data
Data
Data
Data
OP(3:0)
load
op
load
op
t3
t3
DINREADY
t14
/FF
t4
/MF
t6
t7
t10
t11
t5
t5
DOUT(31:0)
read1
t15
readn
t15
/DOUTVALID
/DOUTE
/OE
Figure 5: Sync Port Cycle
Table 7: Sync Port Cycle
- 20
- 30
No.
Name
Min.
Max.
t1
tDVCH
5
7
t2
tCHDX
3
4
t3
tCHDRV
16
18
CLK HIGH to DINREADY valid
t4
tCHMV
10
12
CLK HIGH to /MF valid
t5
tCHQV
15
18
CLK HIGH to DO valid
t6
tCHQZ
0.5
t7
tCHQX
3
2.5
Min.
Max.
Comment
DIN(31:0), OP(3:0) setup to CLK HIGH
CLK HIGH to DIN(31:0), OP(3:0) hold
0.5
4
4
CLK HIGH to DO Hi-Z
CLK HIGH to DO active
t8
tQEVCH
5
7
/DOUTE setup to CLK HIGH
t9
tCHQEX
3
4
CLK HIGH to /DOUTE hold
t10
tGHQZ
0.5
t11
tGLQX
3
3
0.5
4
4
/OE to DO Hi-Z
/OE to DO active
t12
tDEVCH
5
7
/DINE setup to CLK HIGH
t13
tCHDEX
3
4
CLK HIGH to DINE hold
t14
tCHFV
10
12
t15
tCHQVV
10
12
t16
tCHCH
20
30
CLK period
t16A
tCHCL
8
12
CLK HIGH time
t16B
tCLCH
8
12
CLK LOW time
18
CLK HIGH to /FF valid
CLK HIGH to /DOUTVALID
Rev. 5
Timing Diagrams
MUAA Routing CoProcessor (RCP) Family
t20
t28
t23
t26
t21
t29
t24
t27
/PCS
t18
t22
t19
PROCD(31:0) (read)
PROCA(5:0)
R/W (read)
t25
PROCREADY
PROCD(31:0) (write)
R/W (write)
CLK
Figure 6: Processor Port Cycle
Table 8: Processor Port Cycle
- 20
- 30
No.
Name
Min.
Max.
Min.
t18
tSLDQX
t16
Max.
t19
tSHDQZ
t20
tRWVSL
3
4
t21
tSLRWX
3
4
t22
tCHDQV
t23
tDQVSH
5
8
PROCD setup to /PCS HIGH (write)
t24
tSHDQX
3
5
/PCS HIGH to PROCD hold (write)
t25
tCHPRH
t26
tAVSL
5
t27
tSLAX
3
t28
tSLPRH
Nxt16*
Nxt16*
t29
tSHPRL
4xt16*
4xt16*
t30
tCHIV
10
12
t16
Comment
/PCS LOW to PROCD active
8
12
/PCS HIGH to PROCD HI-Z
R/W setup to /PCS LOW
/PCS LOW to R/W hold
15
18
10
12
7
CLK to PROCD valid (read)
CLK HIGH to PROCREADY valid
PROCA setup to /PCS LOW
4
/PCS LOW to PROCA hold
/PCS LOW to PROCREADY HIGH
/PCS HIGH to PROCREADY LOW
CLK HIGH to INT valid
Notes: *
N = 3 for all write operations
N = 6 for all register read operations
N = 10 for read LQUEUE operations
N = 11 for read AQUEUE operations
Assumes no Sync port activity to core on previous processor port core operation pending completion. Depending on Sync port activity (auto-age
events and processor port priority setting), processor port operations may be extended.
Rev. 5
19
MUAA Routing CoProcessor (RCP) Family
Notes
NOTES
20
Rev. 5
Notes
MUAA Routing CoProcessor (RCP) Family
NOTES
Rev. 5
21
MUAA Routing CoProcessor (RCP) Family
Packages
PACKAGES
388-Pin PBGA
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
J
K
L
M
N
F
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
Pin # 1 Corner
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
A
B
C
D
E
F
G
H
J
K
L
M
N
P
E1
E
R
T
U
V
W
Y
AA
AB
AC
AD
AE
4.00 * 45 o (4x)
AF
D1
D
A
L
L1
A1
b
Seating Plane
388-Pin PBGA Dimensions
Dim. A
Dim. A1
Min.
Nom.
Max.
1.17
Dim. b
Dim. D
0.50
34.80
O.70
35.20
1.73
35.00
D1
Dim. E
E1
Dim. e
Dim. F
34.80
30.00
35.00
35.20
22
Dim. L
L1
2.20
32.00
1.27
31.75
2.33
30°
2.46
Rev. 5
Packages
MUAA Routing CoProcessor (RCP) Family
160-Pin PQFP
D
A
D1
A2
A2
D2
E
E1
E2
160-Pin PQFP
L
c
e
b
160-Pin PQFP Dimensions
Dim. A
Min.
Nom.
Max.
Rev. 5
4.10
Dim. A1
Dim. A2
Dim. b
c
0.25
3.20
0.22
0.11
3.32
0.30
0.15
3.60
0.38
0.23
Dim. D
D1
D2
Dim. E
E1
E2
Dim. e
Dim. L
31.20
28.00
25.35
31.20
28.00
25.35
0.65
1.60
23
MUAA Routing CoProcessor (RCP) Family
Ordering Information
ORDERING INFORMATION
Part Number
Cycle Time
Package
Temperature
Voltage
20 ns
30 ns
20 ns
160-Pin PQFP
160-Pin PQFP
388-Pin PBGA
0–70° C
-40–85° C
0–70° C
3.3 ± 0.3
3.3 ± 0.3
3.3 ± 0.3
MUAA2K80-20QGC
MUAA2K80-30QGI
MUAA8K80M-20B388C
MUSIC Semiconductors’ agent or distributor:
Worldwide Headquarters
MUSIC Semiconductors
5850 T.G. Lee Blvd, Suite 345
Orlando, FL 32822
USA
Tel: 407 850-1035
Fax: 407 850-1063
MUSIC Semiconductors reserves the right to make changes to its products and specifications at
any time in order to improve on performance, manufacturability or reliability. Information
furnished by MUSIC is believed to be accurate, but no responsibility is assumed by MUSIC
Semiconductors for the use of said information, nor for any infringements of patents or of other
third-party rights which may result from said use. No license is granted by implication or
otherwise under any patent or patent rights of any MUSIC company.
© Copyright 2000 and 2002, MUSIC Semiconductors
North American Sales
MUSIC Semiconductors
495 Union Ave. , Suite 1B
Middlesex, NJ 08846
USA
Tel: 732 469-1886
Fax: 732 469-2397
USA Only: 800 933-1550 Tech Support
888 226-6874 Product Info
http: //www.musicsemi.com
Asian Headquarters
MUSIC Semiconductors
110 Excellence Ave., SEPZ 1
Carmelray Industrial Park
Canlubang, Laguna
Philippines 4028
Tel: +63 49 549-1480
Fax: +63 49 549-1024
Sales Tel/Fax: +632 723-6215
European Headquarters
MUSIC Semiconductors
P. O. Box 1 84
6470 ED Eygelshoven
The Netherlands
Tel: +31 43 455-2675
Fax: +31 43 455-1573
email: [email protected]
24
Rev. 5
Similar pages