PHILIPS N74F86D Quad 2-input exclusive-or gate Datasheet

INTEGRATED CIRCUITS
74F86
Quad 2-input exclusive-OR gate
Product specification
IC15 Data Handbook
1990 Feb 09
Philips Semiconductors
Product specification
Quad 2-input Exclusive-OR gate
74F86
FEATURE
PIN CONFIGURATION
• Industrial temperature range available (–40°C to +85°C)
TYPE
D0a
1
14
VCC
D0b
2
13
D3b
TYPICAL
PROPAGATION
DELAY
TYPICAL SUPPLY
CURRENT
(TOTAL)
Q0
3
12
D3a
D1a
4
11
Q3
4.3ns
16.5mA
D1b
5
10
D2b
Q1
6
9
D2a
GND
7
8
Q2
74F86
SF00038
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
INDUSTRIAL RANGE
VCC = 5V ±10%, Tamb = –40°C to +85°C
PKG DWG #
14-pin plastic DIP
N74F86N
I74F86N
SOT27-1
14-pin plastic SO
N74F86D
I74F86D
SOT108-1
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS
DESCRIPTION
74F (U.L.) HIGH/LOW
LOAD VALUE HIGH/LOW
Dna, Dnb
Data inputs
1.0/1.0
20µA/0.6mA
Qn
Data output
50/33
1.0mA/20mA
NOTE:
1. One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
LOGIC DIAGRAM
FUNCTION TABLE
1
D0a
D0b
4
5
D1a
D1b
6
9
D2a
D2b
VCC = Pin 14
GND = Pin 7
3
2
8
10
12
D3a
D3b
11
13
INPUTS
Q0
Q1
Q2
Q3
OUTPUT
Dna
Dnb
L
L
Qn
L
L
H
H
H
L
H
H
H
L
NOTES:
H = High voltage level
L = Low voltage level
SF00090
LOGIC SYMBOL
IEC/IEEE SYMBOL
1
2
4
5
9
10 12 13
1
=
3
2
D0a D0bD1a D1b D2a D2b D3a D3b
4
6
5
Q0 Q1 Q2 Q3
9
8
VCC = Pin 14
GND = Pin 7
10
3
6
8
11
SF00040
12
11
13
SF00091
February 9, 1990
2
853–0336 98773
Philips Semiconductors
Product specification
Quad 2-input Exclusive-OR gate
74F86
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limits set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
PARAMETER
RATING
UNIT
VCC
Supply voltage
–0.5 to +7.0
V
VIN
Input voltage
–0.5 to +7.0
V
IIN
Input current
–30 to +5
mA
VOUT
Voltage applied to output in High output state
–0.5 to VCC
V
IOUT
Current applied to output in Low output state
40
mA
0 to +70
°C
–40 to +85
°C
–65 to +150
°C
Commercial range
Tamb
Operating free-air
free air temperature range
Tstg
Storage temperature range
Industrial range
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
MIN
NOM
MAX
5.0
5.5
UNIT
VCC
Supply voltage
4.5
VIH
High-level input voltage
2.0
VIL
Low-level input voltage
0.8
V
IIK
Input clamp current
–18
mA
IOH
High-level output current
–1
mA
IOL
Low-level output current
Tambb
Operating
temperature
O
erating free-air tem
erature range
V
V
20
mA
Commercial range
0
+70
°C
Industrial range
–40
+85
°C
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
TEST CONDITIONS1
PARAMETER
SYMBOL
LIMITS
MIN
VOH
O
±10%VCC
2.5
VIH = MIN, IOH = MAX
±5%VCC
2.7
VCC = MIN, VIL = MAX
±10%VCC
VIH = MIN, IOL = MAX
±5%VCC
VCC = MIN, VIL = MAX
High level output voltage
High-level
TYP2
UNIT
MAX
V
3.4
V
0.30
0.50
V
0.30
0.50
V
-0.73
–1.2
V
100
µA
VOL
O
Low level output voltage
Low-level
VIK
Input clamp voltage
VCC = MIN, II = IIK
II
Input current at maximum input voltage
VCC = MAX, VI = 7.0V
IIH
High-level input current
VCC = MAX, VI = 2.7V
20
µA
IIL
Low-level input current
VCC = MAX, VI = 0.5V
–0.6
mA
IOS
Short-circuit output current3
VCC = MAX
–150
mA
ICC
Supplyy current ((total))
-60
ICCH
VCC = MAX
D0a = GND,
D0b = 4.5V
ICCL
VCC = MAX
VIN = 4.5V
15
23
mA
18
28
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, Tamb = 25°C.
3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, IOS tests should be performed last.
February 9, 1990
3
Philips Semiconductors
Product specification
Quad 2-input Exclusive-OR gate
74F86
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF
RL = 500Ω
VCC = +5.0V
Tamb = +25°C
CL = 50pF
RL = 500Ω
TEST
CONDITION
PARAMETER
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF
RL = 500Ω
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNIT
tPLH
tPHL
Propagation delay
Dna or Dnb to Qn
(other input Low)
Waveform 1
3.0
3.0
4.0
4.2
5.5
5.5
3.0
3.0
6.5
6.5
3.0
2.5
7.0
8.0
ns
tPLH
tPHL
Propagation delay
Dna or Dnb to Qn
(other input High)
Waveform 2
3.5
3.0
5.3
4.7
7.0
6.5
3.5
3.0
8.0
7.5
3.5
3.0
10.0
8.0
ns
VM
VM
AC WAVEFORMS
For all waveforms, VM = 1.5V.
VIN
VM
tPLH
tPHL
VM
VOUT
VIN
VM
tPHL
VM
VOUT
tPLH
VM
VM
SF00093
SF00092
Waveform 1. Propagation Delay for Non-Inverting Outputs
Waveform 2. Propagation Delay for Inverting Outputs
TEST CIRCUIT AND WAVEFORMS
VCC
NEGATIVE
PULSE
VIN
tw
90%
VM
D.U.T.
RT
CL
RL
AMP (V)
VM
10%
VOUT
PULSE
GENERATOR
90%
10%
tTHL (tf )
tTLH (tr )
tTLH (tr )
tTHL (tf )
0V
AMP (V)
90%
90%
POSITIVE
PULSE
DEFINITIONS:
RL = Load resistor;
see AC ELECTRICAL CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance;
see AC ELECTRICAL CHARACTERISTICS for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
VM
VM
10%
Test Circuit for Totem-Pole Outputs
10%
tw
0V
Input Pulse Definition
INPUT PULSE REQUIREMENTS
family
amplitude VM
74F
3.0V
1.5V
rep. rate
tw
tTLH
tTHL
1MHz
500ns
2.5ns
2.5ns
SF00006
February 9, 1990
4
Philips Semiconductors
Product specification
Quad 2-input exclusive-OR gate
74F86
DIP14: plastic dual in-line package; 14 leads (300 mil)
1990 Feb 09
5
SOT27-1
Philips Semiconductors
Product specification
Quad 2-input exclusive-OR gate
74F86
SO14: plastic small outline package; 14 leads; body width 3.9 mm
1990 Feb 09
6
SOT108-1
Philips Semiconductors
Product specification
Quad 2-input exclusive-OR gate
74F86
NOTES
1990 Feb 09
7
Philips Semiconductors
Product specification
Quad 2-input exclusive-OR gate
74F86
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
yyyy mmm dd
8
Date of release: 10-98
9397-750-05068
Similar pages