ON NCP1200D Pwm current-mode controller for universal off-line supplies featuring low standby power Datasheet

NCP1200A
PWM Current−Mode
Controller for Universal
Off−Line Supplies Featuring
Low Standby Power
Housed in SOIC−8 or PDIP−8 package, the NCP1200A enhances
the previous NCP1200 series by offering a reduced optocoupler
current together with an increased drive capability. Due to its novel
concept, the circuit allows the implementation of complete off−line
AC−DC adapters, battery charger or a SMPS where standby power is a
key parameter.
With an internal structure operating at a fixed 40 kHz, 60 kHz or
100 kHz, the controller supplies itself from the high−voltage rail,
avoiding the need of an auxiliary winding. This feature naturally eases
the designer task in battery charger applications. Finally,
current−mode control provides an excellent audio−susceptibility and
inherent pulse−by−pulse control.
When the current setpoint falls below a given value, e.g. the output
power demand diminishes, the IC automatically enters the so−called
skip cycle mode and provides excellent efficiency at light loads.
Because this occurs at a user adjustable low peak current, no acoustic
noise takes place.
The NCP1200A features an efficient protective circuitry which, in
presence of an overcurrent condition, disables the output pulses while
the device enters a safe burst mode, trying to restart. Once the default
has gone, the device auto−recovers.
MINIATURE PWM
CONTROLLER FOR HIGH
POWER AC−DC WALL
ADAPTERS AND OFFLINE
BATTERY CHARGERS
MARKING
DIAGRAMS
8
SOIC−8
D SUFFIX
CASE 751
8
1
8
Typical Applications
• AC−DC Adapters for Portable Devices
• Offline Battery Chargers
• Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
1200APxxx
AWL
YYWW
PDIP−8
P SUFFIX
CASE 626
1
Pb−Free Packages are Available
No Auxiliary Winding Operation
Auto−Recovery Internal Output Short−Circuit Protection
Extremely Low No−Load Standby Power
Current−Mode Control with Skip−Cycle Capability
Internal Temperature Shutdown
Internal Leading Edge Blanking
250 mA Peak Current Capability
Internally Fixed Frequency at 40 kHz, 60 kHz and 100 kHz
Direct Optocoupler Connection
SPICE Models Available for TRANsient and AC Analysis
Pin to Pin Compatible with NCP1200
200Ay
ALYW
1
8
Features
•
•
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
1
xxx
= Specific Device Code
(40, 60 or 100)
y
= Specific Device Code
(4 for 40, 6 for 60, 1 for 100)
A
= Assembly Location
WL, L = Wafer Lot
Y, YY
= Year
W, WW = Work Week
PIN CONNECTIONS
Adj 1
8 HV
FB 2
7 NC
CS 3
6 VCC
GND 4
5 Drv
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
 Semiconductor Components Industries, LLC, 2004
October, 2004− Rev. 5
1
Publication Order Number:
NCP1200A/D
NCP1200A
*
VOUT
+
+
NCP1200A
1
2
EMI
FILTER
3
4
Adj
HV
FB
8
7
CS VCC
GND Drv
UNIVERSAL
INPUT
6
5
+
*Please refer to the application information section
Figure 1. Typical Application Example
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Function
Pin Description
1
Adj
Adjust the skipping peak current
This pin lets you adjust the level at which the cycle skipping process takes
place. Shorting this pin to ground, permanently disables the skip cycle
feature.
2
FB
Sets the peak current setpoint
3
CS
Current sense input
4
GND
The IC ground
−
By connecting an optocoupler to this pin, the peak current setpoint is
adjusted accordingly to the output power demand.
This pin senses the primary current and routes it to the internal comparator
via an L.E.B.
5
Drv
Driving pulses
The driver’s output to an external MOSFET.
6
VCC
Supplies the IC
This pin is connected to an external bulk capacitor of typically 10 F.
7
NC
−
8
HV
Generates the VCC from the line
This unconnected pin ensures adequate creepage distance.
Connected to the high−voltage rail, this pin injects a constant current into
the VCC bulk capacitor.
http://onsemi.com
2
NCP1200A
Adj
HV
8
1
HV CURRENT
SOURCE
80 k
FB
1.2 V
2
SKIP CYCLE
COMPARATOR
+
−
NC
INTERNAL VCC
UVLO HIGH AND LOW
INTERNAL REGULATOR
7
24 k
CURRENT
SENSE
250 ns
L.E.B.
3
20 k
SET
VCC
Q
6
RESET
+
−
57 k
Drv
GROUND
4
40−60−100 kHz
CLOCK
Q FLIP−FLOP
DCmax = 80%
+
−
VREF
25 k
±250 mA
1V
5V
5
OVERLOAD?
FAULT DURATION
Figure 2. Internal Circuit Architecture
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
16
V
Thermal Resistance Junction−to−Air, PDIP−8 Version
Thermal Resistance Junction−to−Air, SOIC Version
RJA
RJA
100
178
°C/W
°C/W
TJ(max)
150
°C
Temperature Shutdown
−
145
°C
Storage Temperature Range
−
−60 to +150
°C
ESD Capability, HBM Model (All pins except VCC and HV)
−
2.0
kV
ESD Capability, Machine Model
−
200
V
Maximum Voltage on Pin 8 (HV), Pin 6 (VCC) Grounded
−
450
V
Maximum Voltage on Pin 8 (HV), Pin 6 (VCC) Decoupled to Ground with 10 F
−
500
V
Minimum Operating Voltage on Pin 8 (HV)
−
40
V
Maximum Junction Temperature
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
http://onsemi.com
3
NCP1200A
ELECTRICAL CHARACTERISTICS (For typical values TJ = 25°C, for min/max values TJ = 0°C to +125°C, Max TJ = 150°C,
VCC = 11 V unless otherwise noted.)
Symbol
Pin
Min
Typ
Max
Unit
VCC Increasing Level at which the Current Source Turns−Off
VCC(off)
6
11.2
12.1
13.1
V
VCC Decreasing Level at which the Current Source Turns−On
VCC(on)
6
9.0
10
11
V
VCC(latch)
6
−
5.4
−
V
Internal IC Consumption, No Output Load on Pin 5
ICC1
6
−
750
1000
(Note 1)
A
Internal IC Consumption, 1.0 nF Output Load on Pin 5, FSW = 40 kHz
ICC2
6
−
1.2
1.4
(Note 2)
mA
Internal IC Consumption, 1.0 nF Output Load on Pin 5, FSW = 60 kHz
ICC2
6
−
1.4
1.6
(Note 2)
mA
Internal IC Consumption, 1.0 nF Output Load on Pin 5, FSW = 100 kHz
ICC2
6
−
1.9
2.2
(Note 2)
mA
Internal IC Consumption, Latchoff Phase
ICC3
6
−
350
−
A
High−Voltage Current Source, VCC = 10 V
IC1
8
4.0
7.0
−
mA
High−Voltage Current Source, VCC = 0
IC2
8
−
13
−
mA
Output Voltage Rise−Time @ CL = 1.0 nF, 10−90% of Output Signal
Tr
5
−
67
−
ns
Output Voltage Fall−Time @ CL = 1.0 nF, 10−90% of Output Signal
Tf
5
−
25
−
ns
Source Resistance
ROH
5
27
40
61
Sink Resistance
ROL
5
5.0
10
21
IIB
3
−
0.02
−
A
Maximum Internal Current Setpoint (Note 3)
ILimit
3
0.8
0.9
1.0
V
Default Internal Current Setpoint for Skip Cycle Operation
ILskip
3
−
360
−
mV
Propagation Delay from Current Detection to Gate OFF State
TDEL
3
−
90
160
ns
Leading Edge Blanking Duration (Note 3)
TLEB
3
−
250
−
ns
Oscillation Frequency, 40 kHz Version
fOSC
−
37
43
48
kHz
Built−in Frequency Jittering, fsw = 40 kHz
fjitter
−
−
350
−
kHz
Oscillation Frequency, 60 kHz Version
fOSC
−
53
61
68
kHz
Built−in Frequency Jittering, fsw = 60 kHz
fjitter
−
−
460
−
kHz
Oscillation Frequency, 100 kHz Version
fOSC
−
90
103
114
kHz
Built−in Frequency Jittering, fsw = 100 kHz
fjitter
−
−
620
−
kHz
Dmax
−
74
83
87
%
Internal Pullup Resistor
Rup
2
−
20
−
k
Pin 3 to Current Setpoint Division Ratio
Iratio
−
−
3.3
−
−
Default Skip Mode Level
Vskip
1
0.95
1.2
1.45
V
Pin 1 Internal Output Impedance
Zout
1
−
22
−
k
Characteristic
Dynamic Self−Supply (All frequency versions, otherwise noted)
VCC Decreasing Level at which the Latchoff Phase Ends
Internal Startup Current Source (TJ > 0°C, pin 8 biased at 50 V)
Drive Output
Current Comparator (Pin 5 unloaded unless otherwise noted)
Input Bias Current @ 1.0 V Input Level on Pin 3
Internal Oscillator (VCC = 11 V, pin 5 loaded by 1.0 k)
Maximum Duty Cycle
Feedback Section (VCC = 11 V, pin 5 unloaded)
Skip Cycle Generation
1. Max value at TJ = 0°C.
2. Maximum value @ TJ = 25°C, please see characterization curves.
3. Pin 5 loaded by 1.0 nF.
http://onsemi.com
4
NCP1200A
TYPICAL CHARACTERISTICS
12.5
60
12.3
VCC(off), THRESHOLD (V)
70
LEAKAGE (A)
50
40
30
20
10
12.1
11.9
11.7
11.5
11.3
0
−25
0
25
50
75
100
11.1
−25
125
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 3. HV Pin Leakage Current vs. Temperature
Figure 4. VCC(off) vs. Temperature
900
10.1
850
10.0
800
ICC1 (A)
10.2
VCC(on), (V)
0
9.9
100 kHz
750
60 kHz
700
9.8
125
40 kHz
650
9.7
9.6
−25
0
25
50
75
100
600
−25
125
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. VCC(on) vs. Temperature
Figure 6. ICC1 vs. Temperature
2.10
110
1.90
104
98
100 kHz
125
100 kHz
92
FSW (kHz)
ICC2 (mA)
1.70
1.50
60 kHz
1.30
80
74
68
60 kHz
62
40 kHz
56
1.10
0.90
−25
86
50
44
0
25
50
75
100
40 kHz
38
−25
125
TEMPERATURE (°C)
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 8. Switching Frequency vs. Temperature
Figure 7. ICC2 vs. Temperature
http://onsemi.com
5
NCP1200A
TYPICAL CHARACTERISTICS
5.50
490
460
5.45
400
ICC3 (A)
VCC LATCHOFF
430
5.40
5.35
5.30
370
340
310
280
5.25
250
5.20
220
5.15
−25
0
25
50
75
100
190
−25
125
50
75
100
TEMPERATURE (°C)
Figure 9. VCC Latchoff vs. Temperature
Figure 10. ICC3 vs. Temperature
125
1.00
CURRENT SETPOINT (V)
50
Source
40
Ohm
25
TEMPERATURE (°C)
60
30
20
Sink
10
0
−25
0
0
25
50
75
100
0.96
0.92
0.88
0.84
0.80
−25
125
0
25
50
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 11. Drive and Source Resistance vs.
Temperature
Figure 12. Current Sense Limit vs. Temperature
1.40
87
1.35
85
DUTY MAX (%)
VSKIP (V)
1.30
1.25
1.20
1.15
83
81
79
1.10
77
1.05
75
1.00
−25
0
25
50
75
100
125
73
−25
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 14. Max Duty Cycle vs. Temperature
Figure 13. VSKIP vs. Temperature
http://onsemi.com
6
125
NCP1200A
APPLICATION INFORMATION
Introduction
The DSS behavior actually depends on the internal IC
consumption and the MOSFET’s gate charge Qg. If we
select a MOSFET like the MTP2N60E, Qg max equals
22 nC. With a maximum switching frequency of 68 kHz for
the P60 version, the average power necessary to drive the
MOSFET (excluding the driver efficiency and neglecting
various voltage drops) is:
FSW ⋅ Qg ⋅ VCC with
FSW = maximum switching frequency
Qg = MOSFET’s gate charge
VCC = VGS level applied to the gate
To obtain the final IC current, simply divide this result by
VCC: Idriver = FSW ⋅ Qg = 1.5 mA. The total standby power
consumption at no−load will therefore heavily rely on the
internal IC consumption plus the above driving current
(altered by the driver’s efficiency). Suppose that the IC is
supplied from a 350 VDC line. The current flowing through
pin 8 is a direct image of the NCP1200A consumption
(neglecting the switching losses of the HV current source).
If ICC2 equals 2.3 mA @ TJ = 25°C, then the power
dissipated (lost) by the IC is simply: 350 x 2.3 m = 805 mW.
For design and reliability reasons, it would be interesting to
reduce this source of wasted power which increases the die
temperature. This can be achieved by using different
methods:
1. Use a MOSFET with lower gate charge Qg
2. Connect pin through a diode (1N4007 typically) to
one of the mains input. The average value on pin 8
The NCP1200A implements a standard current mode
architecture where the switch−off time is dictated by the
peak current setpoint. This component represents the ideal
candidate where low part−count is the key parameter,
particularly in low−cost AC−DC adapters, auxiliary
supplies, etc. Due to its high−performance High−Voltage
technology, the NCP1200A incorporates all the necessary
components normally needed in UC384X based supplies:
timing components, feedback devices, low−pass filter and
self−supply. This later point emphasizes the fact that
ON Semiconductor’s NCP1200A does NOT need an
auxiliary winding to operate: the product is naturally
supplied from the high−voltage rail and delivers a VCC to the
IC. This system is called the Dynamic Self−Supply (DSS).
Dynamic Self−Supply
The DSS principle is based on the charge/discharge of the
VCC bulk capacitor from a low level up to a higher level. We
can easily describe the current source operation with a bunch
of simple logical equations:
POWER−ON: IF VCC < VCCH THEN Current Source is
ON, no output pulses
IF VCC decreasing > VCCL THEN Current Source is OFF,
output is pulsing
IF VCC increasing < VCCH THEN Current Source is ON,
output is pulsing
Typical values are: VCCH = 12 V, VCCL = 10 V
To better understand the operational principle, Figure 15’s
sketch offers the necessary light:
Vripple = 2 V
VMAINS(peak) 2
becomes
. Our power
contribution example drops to: 223 x 2.3 m = 512
mW. If a resistor is installed between the mains and
the diode, you further force the dissipation to
migrate from the package to the resistor. The
resistor value should account for low−line startups.
3. Permanently force the VCC level above VCCH with
an auxiliary winding. It will automatically
disconnect the internal startup source and the IC
will be fully self−supplied from this winding.
Again, the total power drawn from the mains will
significantly decrease. Make sure the auxiliary
voltage never exceeds the 16 V limit.
UVLOH = 12 V
VCC
UVLOL = 10 V
ON
Current
Source
OFF
OUTPUT PULSES
10.0 M
30.0 M
50.0 M
70.0 M
90.0 M
Figure 15. The charge/discharge cycle over a
10 F VCC capacitor
http://onsemi.com
7
NCP1200A
HV
mains
Cbulk
1
8
2
7
3
6
4
5
Figure 16. A simple diode naturally reduces the average voltage on pin 8
Skipping Cycle Mode
To better understand how this skip cycle mode takes place,
a look at the operation mode versus the FB level
immediately gives the necessary insight:
The NCP1200A automatically skips switching cycles
when the output power demand drops below a given level.
This is accomplished by monitoring the FB pin. In normal
operation, pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
determined level, the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the so−called skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 18).
Suppose we have the following component values:
FB
4.2 V, FB Pin Open
3.2 V, Upper
Dynamic Range
NORMAL CURRENT
MODE OPERATION
SKIP CYCLE OPERATION
IP(min) = 333 mV/RSENSE
1V
Figure 17.
Lp, primary inductance = 1 mH
FSW, switching frequency = 61 kHz
Ip skip = 200 mA (or 333 mV/RSENSE)
The theoretical power transfer is therefore:
When FB is above the skip cycle threshold (1 V by
default), the peak current cannot exceed 1 V/RSENSE. When
the IC enters the skip cycle mode, the peak current cannot go
below Vpin1 / 3.3. The user still has the flexibility to alter
this 1 V by either shunting pin 1 to ground through a resistor
or raising it through a resistor up to the desired level.
Grounding pin 1 permanently invalidates the skip cycle
operation.
1 Lp Ip 2 F
SW 1.2 W
2
If this IC enters skip cycle mode with a bunch length of
20 ms over a recurrent period of 100 ms, then the total
power transfer is: 1.2 . 0.2 = 240 mW.
Power P1
Power P2
Power P3
Figure 18. Output Pulses at Various Power Levels (X = 5.0 s/div) P1 P2 P3
http://onsemi.com
8
NCP1200A
MAX PEAK
CURRENT
300 M
SKIP CYCLE
CURRENT LIMIT
200 M
100 M
0
315.40
882.70
1.450 M
2.017 M
2.585 M
Figure 19. The Skip Cycle Takes Place at Low Peak Currents which Guaranties Noise−Free
Operation
disappeared. This option can easily be accomplished
through a single NPN bipolar transistor wired between FB
and ground. By pulling FB below the Adj pin 1 level, the
output pulses are disabled as long as FB is pulled below
pin 1. As soon as FB is relaxed, the IC resumes its operation.
Figure 20 depicts the application example:
We recommend a pin 1 operation between 400 mV and 1.3
V that will fix the skip peak current level between 120 mV
/ RSENSE and 390 mV / RSENSE.
Non−Latching Shutdown
In some cases, it might be desirable to shut off the part
temporarily and authorize its restart once the default has
Q1
ON/OFF
1
8
2
7
3
6
4
5
Figure 20. Another Way of Shutting Down the IC without a Definitive Latchoff State
http://onsemi.com
9
NCP1200A
350 2
Power Dissipation
1.7 m 380 mW b) put an
dissipation to:
auxiliary winding to disable the DSS and decrease the power
consumption to VCC x ICC2. The auxiliary level should be
thus that the rectified auxiliary voltage permanently stays
above 10 V (to not re−activate the DSS) and is safely kept
below the 16 V maximum rating.
The NCP1200A is directly supplied from the DC rail
through the internal DSS circuitry. The average current
flowing through the DSS is therefore the direct image of the
NCP1200A current consumption. The total power
dissipation can be evaluated using: (VHVDC − 11 V) ⋅ ICC2.
If we operate the device on a 250 VAC rail, the maximum
rectified voltage can go up to 350 VDC. However, as the
characterization curves show, the current consumption
drops at high junction temperature, which quickly occurs
due to the DSS operation. At TJ = 50°C, ICC2 = 1.7 mA for
the 61 kHz version over a 1 nF capacitive load. As a result,
the NCP1200A will dissipate 350 . 1.7 mA@TJ = 50°C =
595
mW.
The
SOIC−8
package
offers
a
junction−to−ambient thermal resistance RJA of 178°C/W.
Adding some copper area around the PCB footprint will help
decreasing this number: 12 mm x 12 mm to drop RJA down
to 100°C/W with 35 copper thickness (1 oz.) or 6.5 mm x
6.5 mm with 70 copper thickness (2 oz.). With this later
number, we can compute the maximum power dissipation
the package accepts at an ambient of 50°C:
Overload Operation
In applications where the output current is purposely not
controlled (e.g. wall adapters delivering raw DC level), it is
interesting to implement a true short−circuit protection. A
short−circuit actually forces the output voltage to be at a low
level, preventing a bias current to circulate in the
optocoupler LED. As a result, the FB pin level is pulled up
to 4.2 V, as internally imposed by the IC. The peak current
setpoint goes to the maximum and the supply delivers a
rather high power with all the associated effects. Please note
that this can also happen in case of feedback loss, e.g. a
broken optocoupler. To account for this situation,
NCP1200A hosts a dedicated overload detection circuitry.
Once activated, this circuitry imposes to deliver pulses in a
burst manner with a low duty cycle. The system
auto−recovers when the fault condition disappears.
During the startup phase, the peak current is pushed to the
maximum until the output voltage reaches its target and the
feedback loop takes over. This period of time depends on
normal output load conditions and the maximum peak
current allowed by the system. The time−out used by this IC
works with the VCC decoupling capacitor: as soon as the
VCC decreases from the UVLOH level (typically 12 V) the
device internally watches for an overload current situation.
If this condition is still present when the UVLOL level is
reached, the controller stops the driving pulses, prevents the
self−supply current source to restart and puts all the circuitry
in standby, consuming as little as 350 A typical (ICC3
parameter). As a result, the VCC level slowly discharges
toward 0.
T
T
Pmax Jmax Amax 750 mW
RJA
which is okay with
our previous budget. For the DIP8 package, adding a
min−pad area of 80 mm of 35 copper (1 oz.), RJA drops
from 100°C/W to about 75°C/W.
In the above calculations, ICC2 is based on a 1 nF output
capacitor. As seen before, ICC2 will depend on your
MOSFET’s Qg: ICC2 ≈ ICC1 + FSW x Qg. Final calculation
shall thus accounts for the total gate−charge Qg your
MOSFET will exhibit. The same methodology can be
applied for the 100 kHz version but care must be taken to
keep TJ below the 125°C limit with the D100 (SOIC) version
and activated DSS in high−line conditions.
If the power estimation is beyond the limit, other solutions
are possible a) add a series diode with pin 8 (as suggested in
the above lines) and connect it to the half rectified wave. As
a result, it will drop the average input voltage and lower the
http://onsemi.com
10
NCP1200A
VCC
REGULATION
OCCURS
HERE
12 V
LATCHOFF
PHASE
10 V
5.4 V
TIME
Drv
DRIVER
PULSES
DRIVER
PULSES
TIME
INTERNAL
FAULT FLAG
FAULT IS
RELAXED
TIME
FAULT OCCURS HERE
STARTUP PHASE
Figure 21. If the fault is relaxed during the VCC natural fall down sequence, the IC automatically resumes.
If the fault still persists when VCC reached UVLOL, then the controller cuts everything off until recovery.
When this level crosses 5.4 V typical, the controller enters
a new startup phase by turning the current source on: VCC
rises toward 12 V and again delivers output pulses at the
UVLOH crossing point. If the fault condition has been
removed before UVLOL approaches, then the IC continues
its normal operation. Otherwise, a new fault cycle takes
place. Figure 21 shows the evolution of the signals in
presence of a fault.
in either simulating or measuring in the lab how much time
the system takes to reach the regulation at full load. Let’s
suppose that this time corresponds to 6 ms. Therefore a VCC
fall time of 10 ms could be well appropriated in order to not
trigger the overload detection circuitry. If the corresponding
IC consumption, including the MOSFET drive, establishes
at 1.8 mA for instance, we can calculate the required
t V C
capacitor using the following formula:
, with
i
V = 2 V. Then for a wanted t of 10 ms, C equals 9 F or
22 F for a standard value. When an overload condition
occurs, the IC blocks its internal circuitry and its
consumption drops to 350 A typical. This happens at
VCC = 10 V and it remains stuck until VCC reaches 5.4 V: we
are in latchoff phase. Again, using the calculated 22 F and
350 A current consumption, this latchoff phase lasts:
296 ms.
Calculating the VCC Capacitor
As the above section describes, the fall down sequence
depends upon the VCC level: how long does it take for the
VCC line to go from 12 V to 10 V? The required time depends
on the startup sequence of your system, i.e. when you first
apply the power to the IC. The corresponding transient fault
duration due to the output capacitor charging must be less
than the time needed to discharge from 12 V to 10 V,
otherwise the supply will not properly start. The test consists
http://onsemi.com
11
NCP1200A
Protecting the Controller Against Negative Spikes
fed by its VCC capacitor and keeps activating the MOSFET
ON and OFF with a peak current limited by Rsense.
Unfortunately, if the quality coefficient Q of the resonating
network formed by Lp and Cbulk is low (e.g. the MOSFET
Rdson + Rsense are small), conditions are met to make the
circuit resonate and thus negatively bias the controller. Since
we are talking about ms pulses, the amount of injected
charge (Q = I x t) immediately latches the controller which
brutally discharges its VCC capacitor. If this VCC capacitor
is of sufficient value, its stored energy damages the
controller. Figure 22 depicts a typical negative shot
occurring on the HV pin where the brutal VCC discharge
testifies for latchup.
As with any controller built upon a CMOS technology, it
is the designer’s duty to avoid the presence of negative
spikes on sensitive pins. Negative signals have the bad habit
to forward bias the controller substrate and induce erratic
behaviors. Sometimes, the injection can be so strong that
internal parasitic SCRs are triggered, engendering
irremediable damages to the IC if they are a low impedance
path is offered between VCC and GND. If the current sense
pin is often the seat of such spurious signals, the
high−voltage pin can also be the source of problems in
certain circumstances. During the turn−off sequence, e.g.
when the user unplugs the power supply, the controller is still
Figure 22. A negative spike takes place on the Bulk capacitor at the switch−off sequence
Another option (Figure 24) consists in wiring a diode from
VCC to the bulk capacitor to force VCC to reach UVLOlow
sooner and thus stops the switching activity before the bulk
capacitor gets deeply discharged. For security reasons, two
diodes can be connected in series.
Simple and inexpensive cures exist to prevent from
internal parasitic SCR activation. One of them consists in
inserting a resistor in series with the high−voltage pin to
keep the negative current to the lowest when the bulk
becomes negative (Figure 23). Please note that the negative
spike is clamped to –2 x Vf due to the diode bridge. Please
refer to AND8069/D for power dissipation calculations.
3
Rbulk
> 4.7 k
2
+
Cbulk
1
8
2
7
3
6
4
5
3
+
Cbulk
1 +
CVCC
Figure 23. A simple resistor in series avoids any
latchup in the controller
1
8
2
7
3
6
4
5
D3
1N4007
1 +
CVCC
Figure 24. or a diode forces VCC to reach
UVLOlow sooner
http://onsemi.com
12
NCP1200A
ORDERING INFORMATION
Marking
Package
Shipping†
1200AP40
PDIP−8
50 Units / Rail
1200AP40
PDIP−8
(Pb−Free)
50 Units / Rail
200A4
SOIC−8
2500 Units /Reel
NCP1200AP60
1200AP60
PDIP−8
50 Units / Rail
NCP1200AP60G
1200AP60
PDIP−8
(Pb−Free)
50 Units / Rail
200A6
SOIC−8
2500 Units /Reel
200A6
SOIC−8
(Pb−Free)
2500 Units /Reel
NCP1200AP100
1200AP100
PDIP−8
50 Units / Rail
NCP1200AP100G
1200AP100
PDIP−8
(Pb−Free)
50 Units / Rail
200A1
SOIC−8
2500 Units / Reel
200A1
SOIC−8
(Pb−Free)
2500 Units / Reel
Device
Type
NCP1200AP40
NCP1200AP40G
FSW = 40 kHz
NCP1200AD40R2
NCP1200AD60R2
FSW = 60 kHz
NCP1200AD60R2G
NCP1200AD100R2
NCP1200AD100R2G
FSW = 100 kHz
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
13
NCP1200A
PACKAGE DIMENSIONS
SOIC−8
D SUFFIX
CASE 751−07
ISSUE AC
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
0.25 (0.010)
S
B
1
M
Y
M
4
K
−Y−
G
C
N
X 45 DIM
A
B
C
D
G
H
J
K
M
N
S
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0
8
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 8 0.010
0.020
0.228
0.244
NCP1200A
PACKAGE DIMENSIONS
PDIP−8
P SUFFIX
CASE 626−05
ISSUE L
8
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5
−B−
1
4
F
−A−
NOTE 2
L
C
J
−T−
N
SEATING
PLANE
D
H
M
K
G
0.13 (0.005)
M
T A
M
B
M
http://onsemi.com
15
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
−−−
10
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
−−−
10
0.030
0.040
NCP1200A
The product described herein (NCP1200A), may be covered by the following U.S. patents: 6,271,735, 6,362,067, 6,385,060, 6,429,709, 6,587,357. There
may be other patents pending.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
16
For additional information, please contact your
local Sales Representative.
NCP1200A/D
Similar pages