ON NCV8560MN300R2G High performance low-power, ldo regulator with enable Datasheet

NCV8560
High Performance
Low-Power, LDO Regulator
with Enable
The NCV8560 provides 150 mA of output current at fixed voltage
options, or an adjustable output voltage from 5.0 V down to 1.250 V. It
is designed for portable battery powered applications and offers high
performance features such as low power operation, fast enable
response time, and low dropout.
The device is designed to be used with low cost ceramic capacitors
and is packaged in the DFN6, 3x3 and TSOP−5 packages.
Features
• Output Voltage Options:
•
•
•
•
•
•
•
•
•
Adjustable, 1.3 V, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 3.5 V, 5.0 V
Ultra−Low Dropout Voltage of 150 mV at 150 mA
Adjustable Output by External Resistors from 5.0 V down to 1.250 V
Fast Enable Turn−on Time of 15 ms
Wide Supply Voltage Range Operating Range
Excellent Line and Load Regulation
High Accuracy up to 1.5% Output Voltage Tolerance over All
Operating Conditions
Typical Noise Voltage of 50 mVrms without a Bypass Capacitor
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
Typical Applications
•
•
•
•
www.onsemi.com
ÇÇ
DFN6
MN SUFFIX
CASE 488AE
DFN6
MN SUFFIX
CASE 506BA
TSOP−5
SN SUFFIX
CASE 483
MARKING DIAGRAMS
DFN6
1
1
V8560
xxx
ALYWG
AQ MG
G
V8560 or AQ = Specific Device Code
xxx
= ADJ, 150, 180, 250, 280,
300, 330, 350 or 500
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
M
= Date Code
G
= Pb−Free Package
SMPS Post−Regulation
Hand−held Instrumentation
Noise Sensitive Circuits – VCO, RF Stages, etc.
Camcorders and Cameras
TSOP−5
5
xxxAYWG
G
1
VOUT
VIN
Fixed Voltage Only
Driver w/
Current Limit
+
-
−
= Specific Device Code
= Assembly Location
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
+
GND
xxx
A
Y
W
G
1.25 V
Thermal
Shutdown
ORDERING INFORMATION
ADJ
Adjustable Version Only
See detailed ordering and shipping information in the
package dimensions section on page 13 of this data sheet.
ENABLE
Figure 1. Simplified Block Diagram
© Semiconductor Components Industries, LLC, 2013
February, 2017 − Rev. 5
1
Publication Order Number:
NCV8560/D
NCV8560
PIN CONNECTIONS
Vin
1
GND
2
ENABLE
3
5
ADJ/NC* 1
Vout
GND 2
GND
ENABLE 3
4 ADJ/NC*
(Top View)
6 Vout
Vout 1
5 GND
GND 2
6 Vin
GND
NC 3
4 Vin
(Top View)
5 GND
4 ENABLE
(Top View)
* ADJ − Adjustable Version
* NC − Fixed Voltage Version
* ADJ − Adjustable Version
* NC − Fixed Voltage Version
Figure 2. TSOP5
Figure 3. DFN6 (3x3)
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Figure 4. DFN6 (2x2.2)
PIN FUNCTION DESCRIPTION
Pin No.
DFN6
(2x2.2)
DFN6
(3x3)
3
1
2, 5, EPAD
2, 5, EPAD
4
3
6
4
1
6
TSOP−5
Pin Name
4
ADJ/NC
2
GND
3
ENABLE
1
Vin
Positive Power Supply Input
5
Vout
Regulated Output Voltage
Description
Output Voltage Adjust Input (Adjustable Version), No Connection
(Fixed Voltage Versions) (Note 1)
Power Supply Ground; Device Substrate
The Enable Input places the device into low−power standby when pulled to
logic low (< 0.4 V). Connect to Vin if the function is not used.
1. True no connect. Printed circuit board traces are allowable.
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Min
Max
Unit
Vin
−0.3
6
V
Vout, ENABLE, ADJ
−0.3
Vin + 0.3 V
V
TJ(max)
−
150
°C
TSTG
−65
150
°C
ESD Capability, Human Body Model (Note 3)
ESDHBM
3500
−
V
ESD Capability, Machine Model (Note 3)
ESDMM
200
−
V
Input Voltage (Note 2)
Output, Enable, Adjustable Voltage
Maximum Junction Temperature
Storage Temperature
Moisture Sensitivity Level
MSL
MSL1/260
−
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating: v150 mA per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS
Rating
Symbol
Thermal Characteristics, DFN6, 3x3.3 mm (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
RqJA
Thermal Characteristics, TSOP−5 (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
RqJA
Thermal Characteristics, DFN6, 2x2.2 mm (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
RqJA
Value
°C/W
107
°C/W
205
°C/W
122
4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
5. As measured using a copper heat spreading area of 650 mm2, 1 oz copper thickness.
www.onsemi.com
2
Unit
NCV8560
OPERATING RANGES
Symbol
Min
Max
Unit
Operating Input Voltage (Note 6)
Rating
Vin
Vout + VDO,
1.75 V (Note 7)
6
V
Adjustable Output Voltage Range (Adjustable Version Only)
Vout
1.25
5.0
V
TA
−40
125
°C
Operating Ambient Temperature Range
6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
7. Minimum Vin = 1.75 V or (Vout + VDO), whichever is higher.
ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V (adjustable version)), (Vin = Vout + 0.5 V (fixed version)),
Cin = Cout =1.0 mF, −40°C ≤ TA ≤ 125°C, Figure 5, unless otherwise specified.) (Note 8)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
−
0.01
1.0
mA
−
−
−
−
−
100
135
135
140
145
135
150
170
175
180
GENERAL
Disable Current
IDIS
ENABLE = 0 V, Vin = 6 V
−40°C ≤ TA ≤ 85°C
Ground Current
Adjustable Option
1.3 V Option
1.5 V Option
1.8 V to 3.0 V Option
3.3 V to 5.0 V Option
IGND
ENABLE = 0.9 V,
Iout = 1.0 mA to 150 mA
Thermal Shutdown Temperature (Note 9)
TSD
150
175
200
°C
Thermal Shutdown Hysteresis
TSH
−
10
−
°C
ADJ Input Bias Current
IADJ
−0.75
−
0.75
mA
mA
CHIP ENABLE
ENABLE Input Threshold Voltage
Vth(EN)
V
Voltage Increasing, Logic High
0.9
−
−
Voltage Decreasing, Logic Low
−
−
0.4
−
3.0
100
−
−
−
15
15
30
25
25
50
Enable Input Bias Current (Note 9)
IEN
nA
TIMING
Output Turn On Time
Adjustable Option
1.3 V to 3.5 V Option
5.0 V Option
tEN
ENABLE = 0 V to Vin
ms
8. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
9. Values based on design and/or characterization.
www.onsemi.com
3
NCV8560
ELECTRICAL CHARACTERISTICS
(Vin = 1.750 V, Vout = 1.250 V, Cin = Cout =1.0 mF, −40°C ≤ TA ≤ 125°C, Figure 5, unless otherwise specified.) (Note 10)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
1.231
(−1.5%)
1.250
1.269
(+1.5%)
V
−
−
−
62
55
38
−
−
−
REGULATOR OUTPUT (Adjustable Voltage Version)
Output Voltage
Vout
Iout = 1.0 mA to 150 mA
Vin = 1.75 V to 6.0 V,
Vout = ADJ
Ripple Rejection
(Vin = Vout + 1.0 V + 0.5 Vp−p)
RR
Iout = 1.0 mA to 150 mA
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
dB
Line Regulation
Regline
Vin = 1.750 V to 6.0 V,
Iout = 1.0 mA
−
1.0
10
mV
Load Regulation
Regload
Iout = 1.0 mA to 150 mA
−
2.0
15
mV
f = 10 Hz to 100 kHz
−
50
−
mVrms
300
550
800
mA
−
−
−
−
−
−
175
175
150
125
100
75
250
250
225
175
150
125
Output Noise Voltage (Note 11)
Vn
Output Short Circuit Current
Isc
Dropout Voltage
Vout = 1.25 V
Vout = 1.3 V
Vout = 1.5 V
Vout = 1.8 V
Vout = 2.5 V
Vout ≥ 2.8 V
VDO
Measured at: Vout – 2.0%,
Iout = 150 mA, Figure 6
mV
REGULATOR OUTPUT (Fixed Voltage Version)
(Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, −40°C ≤ TA ≤ 125°C, Figure 7, unless otherwise specified.) (Note 10)
Output Voltage
1.3 V Option
1.5 V Option
1.8 V Option
2.5 V Option
2.8 V Option
3.0 V Option
3.3 V Option
3.5 V Option
5.0 V Option
Vout
Iout = 1.0 mA to 150 mA
Vin = (Vout + 0.5 V) to 6.0 V
Power Supply Ripple Rejection (Note 11)
(Vin = Vout + 1.0 V + 0.5 Vp−p)
PSRR
Line Regulation
Regline
Vin = 1.750 V to 6.0 V,
Iout = 1.0 mA
Load Regulation
1.3 V to 1.5 V Option
1.8 V Option
2.5 V to 5.0 V Option
Regload
Iout = 1.0 mA to 150 mA
Output Noise Voltage (Note 11)
Vn
Output Short Circuit Current
Dropout Voltage
1.3 V Option
1.5 V Option
1.8 V Option
2.5 V Option
2.8 V to 5.0 V Option
Isc
VDO
Iout = 1.0 mA to 150 mA
f = 120 Hz
f = 1.0 kHz
f = 10 kHz
f = 10 Hz to 100 kHz
V
1.274
1.470
1.764
2.450
2.744
2.940
3.234
3.430
4.900
(−2%)
1.326
1.530
1.836
2.550
2.856
3.060
3.366
3.570
5.100
(+2%)
dB
−
−
−
62
55
38
−
−
−
−
1.0
10
−
−
−
2.0
2.0
2.0
20
25
30
−
50
−
mVrms
300
550
800
mA
−
−
−
−
−
175
150
125
100
75
250
225
175
150
125
mV
mV
Measured at: Vout – 2.0%
mV
10. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
11. Values based on design and/or characterization.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
4
NCV8560
VOUT
VIN
VIN
CIN
NCV8560
(adjustable)
ADJ
EN
VOUT
COUT
GND
Figure 5. Typical Application Circuit for Vout = 1.25 V
(Adjustable Version)
VIN
CIN
VOUT
VIN
NCV8560
(adjustable)
ADJ
EN
VOUT
COUT
GND
Figure 6. Typical Application Circuit for Adjustable Vout
VOUT
VIN
VIN
CIN
NCV8560
(fixed)
EN
GND
Figure 7. Typical Application Circuit
(Fixed Voltage Version)
www.onsemi.com
5
VOUT
COUT
NCV8560
TYPICAL CHARACTERISTICS
1.260
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
1.260
1.256
Iout = 1.0 mA
1.252
Iout = 150 mA
1.248
Vin = Vout + 0.5 V
Vout = ADJ
1.244
1.240
−40 −20
0
20
40
60
80
Vin = 6.0 V
Vout = ADJ
1.244
−15
10
35
60
85
110 125
Figure 8. Output Voltage vs. Temperature
(Vin = Vout + 0.5 V)
Figure 9. Output Voltage vs. Temperature
(Vin = 6.0 V)
1.500
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
Iout = 1.0 mA
1.490
Iout = 150 mA
1.485
1.480
−15
10
35
60
85
Iout = 1.0 mA
1.495
1.490
Iout = 150 mA
1.485
1.480
1.475
−40
110 125
−15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 10. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 2 V)
Figure 11. Output Voltage vs. Temperature
(1.5 V Fixed Output, Vin = 6 V)
3.005
3.005
Iout = 1.0 mA
3.000
2.995
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
Iout = 150 mA
1.248
TA, AMBIENT TEMPERATURE (°C)
1.495
Iout = 150 mA
2.990
2.985
2.980
2.975
−40
1.252
TA, AMBIENT TEMPERATURE (°C)
1.500
1.475
−40
Iout = 1.0 mA
1.240
−40
120
100
1.256
−15
10
35
60
85
110 125
Iout = 1.0 mA
3.000
2.995
2.990
Iout = 150 mA
2.985
2.980
2.975
2.970
−40
TA, AMBIENT TEMPERATURE (°C)
−15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
Figure 12. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 3.5 V)
Figure 13. Output Voltage vs. Temperature
(3.0 V Fixed Output, Vin = 6 V)
www.onsemi.com
6
NCV8560
TYPICAL CHARACTERISTICS
5.000
5.000
Iout = 1.0 mA
4.995
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
Iout = 1.0 mA
4.990
Iout = 150 mA
4.985
4.980
4.975
4.970
4.965
−40
−15
10
35
60
110 125
85
4.995
4.990
4.985
Iout = 150 mA
4.980
4.975
4.970
4.965
−40
−15
TA, AMBIENT TEMPERATURE (°C)
60
85
110 125
Figure 15. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 6 V)
250
Vout = ADJ
VDO, DROPOUT VOLTAGE (mV)
250
Iout = 150 mA
200
150
100
Iout = 50 mA
50
Iout = 1.0 mA
0
−40 −20
0
20
40
60
80
100
Iout = 150 mA
Vout = 1.25 V
200
1.50 V
1.80 V
150
2.80 V
100
3.00 V
50
5.00 V
0
−40 −20
120
0
20
40
60
80
100
120
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 16. Dropout Voltage vs. Temperature
(Over Current Range)
Figure 17. Dropout Voltage vs. Temperature
(Over Output Voltage)
800
6.0
5.5
5.0
Iout = 0 mA
Cout = 1.0 mF
TA = 25°C
ENABLE = Vin
4.5
4.0
Vth(EN), ENABLE THRESHOLD (mV)
VDO, DROPOUT VOLTAGE (mV)
35
TA, AMBIENT TEMPERATURE (°C)
Figure 14. Output Voltage vs. Temperature
(5.0 V Fixed Output, Vin = 5.5 V)
Vout, OUTPUT VOLTAGE (V)
10
5.0 V
3.3 V
3.0 V
3.5
3.0
2.80 V
2.5
2.0
1.80 V
1.5 V
1.5
1.0
1.25 V
0.5
0
0
1.0
2.0
3.0
4.0
5.0
750
Enable Increasing
700
Enable Decreasing
650
Vin = 5.5 V
600
−40
6.0
−15
10
35
60
85
110 125
Vin, INPUT VOLTAGE (V)
TA, AMBIENT TEMPERATURE (°C)
Figure 18. Output Voltage vs. Input Voltage
Figure 19. Enable Threshold vs. Temperature
www.onsemi.com
7
NCV8560
TYPICAL CHARACTERISTICS
154
IGND, GROUND CURRENT (mA)
IGND, GROUND CURRENT (mA)
6.0
5.0
4.0
3.0
2.0
ENABLE = 0 V
1.0
0
−40
−15
10
35
60
85
110
146
125
Iout = 150 mA
Vout = 5.0 V
138
130
122
114
Vout = 1.25 V
Iout = 1.0 mA
106
Iout = 150 mA
98
ENABLE = 0.9 V
90
−40
−20
0
20
40
60
100
80
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 20. Ground Current (Sleep Mode) vs.
Temperature
Figure 21. Ground Current (Run Mode) vs.
Temperature
120
106
160
140
3.0 V
1.5 V
IGND, GROUND CURRENT (mA)
2.8 V
5.0 V
3.3 V
120
1.8 V
1.25 V
100
80
60
40
20
105
104
103
102
101
100
Vout = ADJ
Vin = 1.75 V
99
98
0
0
1.0
2.0
3.0
4.0
0
6.0
5.0
25
50
75
100
125
150
Vin, INPUT VOLTAGE (V)
Iout, OUTPUT CURRENT (mA)
Figure 22. Ground Current vs. Input Voltage
Figure 23. Ground Current vs. Output Current
IADJ, ADJ INPUT BIAS CURRENT (nA)
IGND, GROUND CURRENT (mA)
Iout = 1.0 mA
400
300
200
100
0
−40
−20
0
20
40
60
80
100
120
TA, AMBIENT TEMPERATURE (°C)
Figure 24. ADJ Input Bias Current vs. Temperature
www.onsemi.com
8
NCV8560
700
650
ILIM, CURRENT LIMIT (mA)
ISC, OUTPUT SHORT CIRCUIT CURRENT (mA)
TYPICAL CHARACTERISTICS
600
550
500
450
−40 −20
600
500
400
300
200
100
0
0
20
40
60
80
100
0
120
5.0
4.0
Figure 25. Output Short Circuit Current vs.
Temperature
Figure 26. Current Limit vs. Input Voltage
6.0
5.0
Regload, LOAD REGULATION (mV)
3.0
2.0
1.0
Vin = (Vout + 0.5 V) to 6.0 V
Iout = 1.0 mA
0
20
40
60
80
100
120
4.0
3.0
2.0
1.0
Iout = 1.0 mA to 150 mA
0
−40
−15
10
35
60
85
110 125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 27. Line Regulation vs. Temperature
Figure 28. Load Regulation vs. Temperature
45
80
40
70
1.25 V
60
35
3.3 V
5.0 V
PSRR (dB)
Regline, LINE REGULATION (mV)
3.0
Vin, INPUT VOLTAGE (V)
0
−40 −20
ton, OUTPUT TURN ON TIME (mS)
2.0
TA, AMBIENT TEMPERATURE (°C)
4.0
30
25
3.0 V
20
15
1.0
1.5 V
40
5.0 V
30
Vin = Vout + 1.0 V
Vripple = 0.5 Vp−p
Cout = 1.0 mF
Iout = 1.0 mA to 150 mA
20
1.25 V (ADJ)
10
−40 −20
50
10
0
0
20
40
60
80
100
120
0.1
1.0
10
100
TA, AMBIENT TEMPERATURE (°C)
f, FREQUENCY (kHz)
Figure 29. Output Turn On Time vs.
Temperature
Figure 30. Power Supply Ripple Rejection vs.
Frequency
www.onsemi.com
9
NCV8560
TYPICAL CHARACTERISTICS
OUTPUT CAPACITOR ESR (W)
10
Unstable Region
Vout = 5.0 V
Vout = 1.25 V
1.0
Stable Region
0.1
Cout = 1.0 mF to 10 mF
TA = −40°C to 125°C
Vin = up to 6.0 V
0.01
0
25
50
75
100
125
Iout, OUTPUT CURRENT (mA)
Figure 31. Output Stability with Output
Capacitor ESR over Output Current
Vout = 1.25 V
Figure 32. Load Transient Response (1.0 mF)
Vout = 1.25 V
Figure 33. Load Transient Response (10 mF)
www.onsemi.com
10
150
NCV8560
DEFINITIONS
Load Regulation
Line Regulation
The change in output voltage for a change in output load
current at a constant temperature.
The change in output voltage for a change in input voltage.
The measurement is made under conditions of low
dissipation or by using pulse techniques such that the
average junction temperature is not significantly affected.
Dropout Voltage
The input/output differential at which the regulator output
no longer maintains regulation against further reductions in
input voltage. Measured when the output drops 2% below its
nominal. The junction temperature, load current, and
minimum input supply requirements affect the dropout level.
Line Transient Response
Typical output voltage overshoot and undershoot
response when the input voltage is excited with a given
slope.
Output Noise Voltage
Load Transient Response
This is the integrated value of the output noise over a
specified frequency range. Input voltage and output load
current are kept constant during the measurement. Results
are expressed in mVrms or nV/√Hz.
Typical output voltage overshoot and undershoot
response when the output current is excited with a given
slope between no−load and full−load conditions.
Thermal Protection
Internal thermal shutdown circuitry is provided to protect
the integrated circuit in the event that the maximum junction
temperature is exceeded. When activated at typically 175°C,
the regulator turns off. This feature is provided to prevent
failures from accidental overheating.
Ground Current
Ground Current (IGND) is the current that flows through
the ground pin when the regulator operates with a load on its
output. This consists of internal IC operation, bias, etc. It is
actually the difference between the input current (measured
through the LDO input pin) and the output load current. If
the regulator has an input pin that reduces its internal bias
and shuts off the output (enable/disable function), this term
is called the disable current (IDIS).
Maximum Package Power Dissipation
The power dissipation level at which the junction
temperature reaches its maximum operating value.
APPLICATIONS INFORMATION
output, there is no resistor divider. If the part is enabled
under no−load conditions, leakage current through the pass
transistor at junction temperatures above 85°C can approach
several microamps, especially as junction temperature
approaches 150°C. If this leakage current is not directed into
a load, the output voltage will rise up to a level
approximately 20 mV above nominal.
The NCV8560 contains an overshoot clamp circuit to
improve transient response during a load current step
release. When output voltage exceeds the nominal by
approximately 20 mV, this circuit becomes active and
clamps the output from further voltage increase. Tying the
ENABLE pin to Vin will ensure that the part is active
whenever the supply voltage is present, thus guaranteeing
that the clamp circuit is active whenever leakage current is
present.
When the NCV8560 adjustable regulator is disabled, the
overshoot clamp circuit becomes inactive and the pass
transistor leakage will charge any capacitance on Vout. If no
load is present, the output can charge up to within a few
millivolts of Vin. In most applications, the load will present
some impedance to Vout such that the output voltage will be
inherently clamped at a safe level. A minimum load of
10 mA is recommended.
The NCV8560 series regulator is self−protected with
internal thermal shutdown and internal current limit. Typical
application circuits are shown in Figures 5 and 6.
Input Decoupling (Cin)
A ceramic or tantalum 1.0 mF capacitor is recommended
and should be connected close to the NCV8560 package.
Higher capacitance and lower ESR will improve the overall
line transient response.
Output Decoupling (Cout)
The NCV8560 is a stable component and does not require
a minimum Equivalent Series Resistance (ESR) for the
output capacitor. The minimum output decoupling value is
1.0 mF and can be augmented to fulfill stringent load
transient requirements. The regulator works with ceramic
chip capacitors as well as tantalum devices. Larger values
improve noise rejection and load regulation transient
response. Figure 31 shows the stability region for a range of
operating conditions and ESR values.
No−Load Regulation Considerations
The NCV8560 adjustable regulator will operate properly
under conditions where the only load current is through the
resistor divider that sets the output voltage. However, in the
case where the NCV8560 is configured to provide a 1.250 V
www.onsemi.com
11
NCV8560
Noise Decoupling
600 mW when the ambient temperature (TA) is 25°C, and
PCB area is 150mm2 and larger, see Figure 34.
The power dissipated by the NCV8560 can be calculated
from the following equations:
The NCV8560 is a low noise regulator and needs no
external noise reduction capacitor. Unlike other low noise
regulators which require an external capacitor and have slow
startup times, the NCV8560 operates without a noise
reduction capacitor, has a typical 15 ms start up delay and
achieves a 50 mVrms overall noise level between 10 Hz and
100 kHz.
P D [ V inǒI GND @ I outǓ ) I outǒV in * V outǓ
or
V in(MAX) [
Enable Operation
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. The turn−on/turn−off transient
voltage being supplied to the enable pin should exceed a
slew rate of 10 mV/ms to ensure correct operation. If the
enable function is not to be used then the pin should be
connected to Vin.
RthJA, THERMAL RESISTANCE JUNCTION−TO−AMBIENT (°C/W)
The output voltage can be adjusted from 1 times
(Figure 5) to 4 times (Figure 6) the typical 1.250 V
regulation voltage via the use of resistors between the output
and the ADJ input. The output voltage and resistors are
chosen using Equation 1 and Equation 2.
V out + 1.250
ǒ
1)
R2 ^
Ǔ
R2
) ǒI ADJ
R 1Ǔ
(eq. 1)
R1
V
out
1.25
*1
(eq. 2)
Input bias current IADJ is typically less than 150 nA.
Choose R2 arbitrarily to minimize errors due to the bias
current and to minimize noise contribution to the output
voltage. Use Equation 2 to find the required value for R1.
Thermal
As power in the NCV8560 increases, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and the ambient temperature
affect the rate of junction temperature rise for the part. When
the NCV8560 has good thermal conductivity through the
PCB, the junction temperature will be relatively low with
high power applications. The maximum dissipation the
NCV8560 can handle is given by:
PD(MAX) +
TJ(MAX) * TA
RqJA
P D(MAX) ) ǒV out
I outǓ
(eq. 5)
I out ) I GND
If a 150 mA output current is needed, the quiescent current
IGND is taken from the data sheet electrical characteristics
table or extracted from Figure 21 and Figure 23. IGND is
approximately 108 mA when Iout = 150 mA. For an output
voltage of 1.250 V, the maximum input voltage will then be
3.9 V, good for a 1 Cell Li−ion battery.
Output Voltage Adjust
R1
(eq. 4)
350
300
TSOP−5 (1 oz)
250
200
DFN6 3x3.3 (1 oz)
150
100
50
0
0
100
200
300
400
500
PCB COPPER AREA (mm2)
600
700
Figure 34. RthJA vs. PCB Copper Area
Hints
Vin and GND printed circuit board traces should be as
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCV8560, and
make traces as short as possible.
(eq. 3)
Since TJ is not recommended to exceed 125°C (TJ(MAX)),
then the NCV8560 in a DFN6 package can dissipate up to
www.onsemi.com
12
NCV8560
DEVICE ORDERING INFORMATION
Device*
Marking Code
Version
NCV8560MNADJR2G
1st Line: V8560
2nd Line: ADJ
ADJ
NCV8560MN150R2G
1st Line: V8560
2nd Line: 150
1.5 V
NCV8560MN180R2G
1st Line: V8560
2nd Line: 180
1.8 V
NCV8560MN250R2G
1st Line: V8560
2nd Line: 250
2.5 V
NCV8560MN280R2G
1st Line: V8560
2nd Line: 280
2.8 V
NCV8560MN300R2G
1st Line: V8560
2nd Line: 300
3.0 V
NCV8560MN330R2G
1st Line: V8560
2nd Line: 330
3.3 V
NCV8560MN350R2G
1st Line: V8560
2nd Line: 350
3.5 V
NCV8560MN500R2G
1st Line: V8560
2nd Line: 500
5.0 V
NCV8560MN130R2G
1st Line: AQ(M)
1.3 V
NCV8560SNADJT1G
LJ9
ADJ
NCV8560SN130T1G
LJ2
1.3 V
NCV8560SN150T1G
AAJ
1.5 V
NCV8560SN180T1G
LJ3
1.8 V
NCV8560SN250T1G
AAQ
2.5 V
NCV8560SN280T1G
AAR
2.8 V
NCV8560SN300T1G
LJ4
3.0 V
NCV8560SN330T1G
LJ5
3.3 V
NCV8560SN350T1G
LJ7
3.5 V
NCV8560SN500T1G
LJ8
5.0 V
Package
Shipping†
DFN6 (3x3)
(Pb−Free)
3000/Tape & Reel
DFN6 (2x2.2)
(Pb−Free)
3000/Tape & Reel
TSOP−5
(Pb−Free)
3000/Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
www.onsemi.com
13
NCV8560
PACKAGE DIMENSIONS
DFN6, 2x2.2, 0.65P
CASE 506BA−01
ISSUE A
A
B
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.20 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L
L
L1
ÉÉÉ
ÉÉÉ
PIN ONE
REFERENCE
2X
0.10 C
DETAIL A
E
ALTERNATE TERMINAL
CONSTRUCTIONS
ÉÉ
ÉÉ
EXPOSED Cu
TOP VIEW
2X
0.10 C
A
0.10 C
ÉÉ
ÇÇ
ÇÇ
A3
MOLD CMPD
A1
DETAIL B
DETAIL B
DIM
A
A1
b
D
D2
E
E2
e
K
L
L1
ALTERNATE
CONSTRUCTIONS
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20
0.30
2.00 BSC
1.10
1.30
2.20 BSC
0.70
0.90
0.65 BSC
0.20
−−−
0.25
0.35
0.00
0.10
7X
0.08 C
SOLDERING FOOTPRINT*
SIDE VIEW
C
A1
SEATING
PLANE
1.36
PACKAGE
OUTLINE
D2
6X
0.58
DETAIL A
6X
L
e
6X
3
1
L1
2.50
0.96
E2
1
K
6
4
BOTTOM VIEW
6X
b
6X
0.35
0.10 C A B
0.05 C
0.65
PITCH
DIMENSIONS: MILLIMETERS
NOTE 3
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
14
NCV8560
PACKAGE DIMENSIONS
DFN6 3x3
CASE 488AE
ISSUE B
EDGE OF PACKAGE
A
D
B
L1
E
PIN ONE
REFERENCE
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. TERMINAL b MAY HAVE MOLD COMPOUND
MATERIAL ALONG SIDE EDGE. MOLD
FLASHING MAY NOT EXCEED 30 MICRONS
ONTO BOTTOM SURFACE OF TERMINAL b.
ÇÇÇ
ÇÇÇ
ÇÇÇ
DETAIL A
BOTTOM VIEW
0.15 C
2X
EXPOSED Cu
0.15 C
2X
MOLD COMPOUND
TOP VIEW
DETAIL B
0.10 C
6X
0.08 C
A1
SEATING
PLANE
ÇÇÇ
ÇÇÇ
A
A1
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
DETAIL B
SIDE VIEW
(A3)
C
SIDE VIEW
D2
ÇÇÇ
ÇÇÇ
1
6X
L
6X
K
ÇÇÇ
ÇÇÇ
6
3
e
DETAIL A
E2
4
BOTTOM VIEW
6X
b
NOTE 3
0.10 C A B
0.05 C
www.onsemi.com
15
(A3)
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20
0.25
0.18
0.30
3.00 BSC
2.25
2.55
3.00 BSC
1.55
1.85
0.65 BSC
0.20
−−−
0.30
0.50
0.00 0.021
NCV8560
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE K
NOTE 5
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
D 5X
0.20 C A B
0.10 T
M
2X
0.20 T
B
5
1
4
2
S
3
K
B
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
SIDE VIEW
C
SEATING
PLANE
END VIEW
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
16
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV8560/D