NJRC NJW4152-AB Switching regulator ic for buck converter Datasheet

NJW4152-AB
Switching Regulator IC for Buck Converter
w/ 40V/1A MOSFET
GENERAL DESCRIPTION
■ PACKAGE OUTLINE
The NJW4152 is a buck converter with 40V/1A MOSFET. It corresponds
to high oscillating frequency, and Low ESR Output Capacitor (MLCC) within
wide input range from 3.6V to 40V. Therefore, the NJW4152 can realize
downsizing of an application with a few external parts.
Also, it has a soft start function, an over current protection and a thermal
shutdown circuit. Moreover there is an automotive for extended operating
temperature range version.
It is suitable for logic voltage generation from high voltage that Car
Accessory, Office Automation Equipment, Industrial Instrument and so on.
NJW4152GM1-AB
FEATURES
Maximum Rating Input Voltage
45V
Wide Operating Voltage Range
3.6V to 40V @AB version
Switching Current
1.4A(min.) @AB version
PWM Control
Wide Oscillating Frequency
300kHz to 1MHz
Soft Start Function
4ms typ.
UVLO (Under Voltage Lockout)
Over Current Protection / Thermal Shutdown Protection
Standby Function
Package Outline
NJW4152GM1: HSOP8
PRODUCT CLASSIFICATION
Status
Part Number
Version
Output
Current
Switching
Current Limit
(MIN.)
Operating
Voltage
Package
MP
NJW4152GM1-A
A
1.0A
1.4A
4.6 to 40V
HSOP8
MP
NJW4152GM1-A-T
A
1.0A
1.4A
4.6 to 40V
HSOP8
MP
NJW4152GM1-A-T1
A
1.0A
1.4A
4.6 to 40V
HSOP8
MP
NJW4152GM1-AB
AB
1.0A
1.4A
3.6 to 40V
HSOP8
MP
NJW4152GM1-AB-T1
AB
1.0A
1.4A
3.6 to 40V
HSOP8
MP
NJW4152R-B
B
600mA
0.8A
4.6 to 40V
U.D.
NJW4152R-BA-Z
BA
600mA
0.8A
4.4 to 40V
MSOP8
(VSP8)
MSOP8
(VSP8)
Operating
Temperature Range
General Spec.
-40 to +85°C
Automotive T Spec.
-40 to +105°C
Automotive T1 Spec.
-40 to +125°C
General Spec.
-40 to +85°C
Automotive T1 Spec.
-40 to +125°C
General Spec.
-40 to +85°C
Automotive Z Spec.
-40 to +125°C
This data sheet is applied to "NJW4152GM1-AB".
Please refer to each data sheet for other versions.
Ver.2013-01-23
-1-
NJW4152-AB
PIN CONFIGURATION
1
8
2
7
3
6
4
5
Exposed PAD on
backside connect to GND
PIN FUNCTION
1. PV+
2. V+
3. ON/OFF
4. RT
5. IN6. FB
7. GND
8. SW
NJW4152GM1-AB
BLOCK DIAGRAM
V
+
PV
+
Regulator
OCP
UVLO
ON/OFF
High: ON
Low : OFF
(Standby)
Pulse by Pulse
Standby
ON/OFF
Low Frequency
Control
480kΩ
FB
PWM
OSC
ER⋅AMP
Buffer
IN-
SW
Vref
Soft Start
TSD
0.8V
RT
-2-
GND
Ver.2013-01-23
NJW4152-AB
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Supply Voltage
V+
(V+ pin, PV+ pin)
PV+- SW pin Voltage
VPV-SW
IN- pin Voltage
VINON/OFF pin Voltage
VON/OFF
Power Dissipation
PD
Junction Temperature Range
Operating Temperature Range
Storage Temperature Range
Tj
Topr
Tstg
MAXIMUM RATINGS
(Ta=25°C)
UNIT
+45
V
+45
-0.3 to +6
+45
V
V
V
HSOP8
790 (*1)
2,500 (*2)
-40 to +150
-40 to +85
-40 to +150
mW
°C
°C
°C
(*1): Mounted on glass epoxy board. (76.2×114.3×1.6mm:EIA/JDEC standard size, 2Layers)
(*2): Mounted on glass epoxy board. (76.2×114.3×1.6mm:EIA/JDEC standard size, 4Layers),
internal Cu area: 74.2×74.2mm
RECOMMENDED OPERATING CONDITIONS
PARAMETER
SYMBOL
Supply Voltage
V+
Output Current (*3)
IOUT
Timing Resistor
RT
Oscillating Frequency
fosc
(*3): At Static Status
Ver.2013-01-23
MIN.
3.6
–
18
300
TYP.
–
–
27
700
MAX.
40
1.0
68
1,000
UNIT
V
A
kΩ
kHz
-3-
NJW4152-AB
(Unless otherwise noted, V+=VON/OFF=12V, RT=27kΩ, Ta=25°C)
ELECTRICAL CHARACTERISTICS
PARAMETER
Under Voltage Lockout Block
ON Threshold Voltage
OFF Threshold Voltage
SYMBOL
VT_ON
VT_OFF
Hysteresis Voltage
VHYS
Soft Start Block
Soft Start Time
TSS
Oscillator Block
Oscillation Frequency
Oscillation Frequency
(Low Frequency Control)
RT pin Voltage
Oscillation Frequency deviation
(Supply voltage)
Oscillation Frequency deviation
(Temperature)
TEST CONDITION
V+= L → H
+
V =H→L
VB=0.75V
fOSC
fOSC_LOW
VIN-=0.4V, VFB=0.55V
VRT
+
MIN.
TYP.
MAX.
UNIT
3.2
3.4
3.6
V
3.1
3.3
3.5
V
60
100
–
mV
2
4
8
ms
630
700
770
kHz
–
270
–
kHz
0.24
0.275
0.31
V
fDV
V =4.6V to 40V
–
1
–
%
fDT
Ta=-40°C to +85°C
–
2
–
%
VFB=1V, VIN-=0.7V
VFB=1V, VIN-=0.9V
-1.0%
-0.1
–
–
8
1
0.8
–
80
0.6
16
2
+1.0%
+0.1
–
–
24
4
V
µA
dB
MHz
µA
mA
VIN-=0.7V
100
–
–
%
ISW=1A
0.3
1.7
–
0.5
2.0
1
Ω
A
µA
Error Amplifier Block
Reference Voltage
Input Bias Current
Open Loop Gain
Gain Bandwidth
Output Source Current
Output Sink Current
VB
IB
AV
GB
IOM+
IOM-
PWM Comparate Block
Maximum Duty Cycle
MAXDUTY
Output Block
Output ON Resistance
Switching Current Limit
Switching Leak Current
RON
ILIM
ILEAK
VON/OFF=0V, V+=45V, VSW=0V
–
1.4
–
ON/OFF Block
ON Control Voltage
VON
VON/OFF= L → H
1.6
–
V+
V
OFF Control Voltage
VOFF
VON/OFF= H → L
0
–
0.5
V
Pull-down Resistance
RPD
–
480
–
kΩ
General Characteristics
Quiescent Current
IDD
RL=no load, VIN-=0.7V, VFB=0.55V
–
2.5
2.8
mA
VON/OFF=0V
–
–
1
µA
Standby Current
-4-
IDD_STB
Ver.2013-01-23
NJW4152-AB
TYPICAL APPLICATIONS
CIN2
V IN
CIN1
ON/OFF
High: ON
Low: OFF
(Standby)
4
RT
3
2
ON/OFF V +
RT
1
PV +
NJW4152
IN-
FB
GND
SW
5
6
7
8
L
SBD
RNF
CNF
COUT
V OUT
CFB
R2
RFB
R1
Ver.2013-01-23
-5-
NJW4152-AB
CHARACTERISTICS
Timing Resistor vs. Oscillation Frequency
+
(V =12V, Ta=25°C)
770
Oscillation Frequnecny fOSC (kHz)
Oscillation Frequnecny fOSC (kHz)
1000
10
710
690
670
650
100
10
20
30
+
Supply Voltage V (V)
Reference Voltage vs. Supply Voltage
(AB ver., Ta=25°C)
Output ON Resistance vs. Supply Voltage
(AB ver., Ta=25°C)
0
0.40
0.805
0.8
0.795
40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0
10
20
30
+
Supply Voltage V (V)
0
40
Quiescent Current vs. Supply Voltage
(RT=27kΩ, RL=no load, VIN-=0.7V, Ta=25°C)
4
2
1
Error Amplifier Block
Voltage Gain, Phase vs. Frequency
+
(V =12V, Gain=40dB, Ta=25°C)
60
Voltage Gain Av (dB)
3
10
20
30
+
Supply Voltage V (V)
45
0
10
20
30
+
Supply Voltage V (V)
40
180
135
Phase
Gain
30
90
15
45
0
0
40
10
100
1k
10k
100k
Frequency f (Hz)
1M
Phase Φ (deg)
0.79
Quiescent Current IDD (mA)
730
Timing Resistor RT (kΩ)
Output ON Resistance RON (Ω)
0.81
Reference Voltage VB (V)
750
630
100
-6-
Oscillation Frequency vs. Supply Voltage
(RT=27kΩ, Ta=25°C)
0
10M
Ver.2013-01-23
NJW4152-AB
■ CHARACTERISTICS
Oscillation Frequency vs Temperature
+
(V =12V, RT=27kΩ)
Reference Voltage VB (V)
0.806
720
700
680
0.804
0.802
0.800
0.798
0.796
0.794
660
0.792
-50
2.6
Limited Switching Current ILIM (A)
0.808
-50
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
Limited Switching Current vs. Temperature
(AB ver.)
2.4
2.2
+
V =40V
+
V =12V
2
1.8
1.6
+
V =3.6V
1.4
1.2
+
V =3.6V
+
V =4V
+
V =6V
0.5
0.4
0.3
+
V =12V, 40V
0.2
0.1
1
0
-50
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
-50
Under Voltage Lockout Voltage
vs. Temperature (AB ver.)
3.5
VT_ON
3.4
3.3
VT_OFF
3.2
3.1
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
Soft Start Time vs. Temperature
+
(V =12V, VB=0.75V)
8
Soft Start Time Tss (ms)
3.6
Threshold Voltage (V)
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
Output ON Resistance vs. Temperature
(AB ver., ISW=1A)
0.6
Output ON Resistance RON (Ω)
Oscillation Frequency fosc (kHz)
740
Reference Voltage vs. Temperature
+
(V =12V)
7
6
5
4
3
2
-50
Ver.2013-01-23
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
-50
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
-7-
NJW4152-AB
CHARACTERISTICS
Quiescent Current vs. Temperature
(RT=27kΩ, RL=no load, VIN-=0.7V)
3.5
+
V =40V
3
2.5
+
V =12V
2
1.5
+
V =3.6V
1
0.5
0
0.8
0.6
0.4
+
V =40V
0.2
+
V =12V
0
-50
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
-50
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
Switching Leak Current vs. Temperature
+
(V =45V, VON/OFF=0V, VSW=0V)
5
Switching Leak Current ILEAK (µA)
1
Standby Current IDD_STB (µA)
Quiescent Current IDD (mA)
4
Standby Current vs. Temperature
(VON/FF=0V)
4
3
2
1
0
-50
-8-
-25
0
25 50 75 100 125 150
Ambient Temperature Ta (°C)
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
PIN DESCRIPTIONS
PIN
PIN NAME
NUMBER
1
PV+
2
V+
3
ON/OFF
4
RT
5
IN-
6
FB
7
8
GND
SW
Exposed
PAD
–
FUNCTION
Power Supply pin for Power Line
Power Supply pin for IC Control
ON/OFF Control pin
The ON/OFF pin internally pulls down with 480kΩ. Normal Operation at the time
of High Level. Standby Mode at the time of Low Level or OPEN.
Oscillating Frequency Setting pin by Timing Resistor.
Oscillating Frequency should set between 300kHz and 1MHz.
Output Voltage Detecting pin
Connects output voltage through the resistor divider tap to this pin in order to
voltage of the IN- pin become 0.8V.
Feedback Setting pin
The feedback resistor and capacitor are connected between the FB pin and the
IN- pin.
GND pin
Switch Output pin of Power MOSFET
Connect to GND
Description of Block Features
1. Basic Functions / Features
Error Amplifier Section (ER⋅AMP)
0.8V±1% precise reference voltage is connected to the non-inverted input of this section.
To set the output voltage, connects converter's output to inverted input of this section (IN- pin). If requires output
voltage over 0.8V, inserts resistor divider.
Because the reference voltage has decreased supply voltage on the operating conditions less than 4V*, please
confirm "Reference voltage vs. Supply voltage" characteristic.
This AMP section has high gain and external feedback pin (FB pin). It is easy to insert a feedback resistor and a
capacitor between the FB pin and the IN- pin, making possible to set optimum loop compensation for each type of
application. (* Design value)
Oscillation Circuit Section (OSC)
Oscillation frequency can be set by inserting resistor between the RT pin and GND. Referring to the sample
characteristics in "Timing Resistor and Oscillation Frequency", set oscillation between 300kHz and 1MHz.
Ver.2013-01-23
-9-
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Description of Block Features (Continued)
PWM Comparator Section (PWM)
This section controls the switching duty ratio.
PWM comparator receives the signal of the error amplifier and the triangular wave, and controls the duty ratio
between 0% and 100%. The timing chart is shown in Fig.1.
FB pin Voltage
OSC
Waveform
(IC internal)
Maximum duty: 100%
ON
SW pin
OFF
Fig. 1. Timing Chart PWM Comparator and SW pin
Power MOSFET (SW Output Section)
The power is stored in the inductor by the switch operation of built-in power MOSFET. The output current is limited
to 1.4A(min.)@AB version by the overcurrent protection function. In case of step-down converter, the forward
direction bias voltage is generated with inductance current that flows into the external regenerative diode when
MOSFET is turned off.
The SW pin allows voltage between the PV+ pin and the SW pin up to +45V. However, you should use an
Schottky diode that has low saturation voltage.
When the power supply voltage decreases, ON resistance rises. Because a dropout voltage in the MOSFET
becomes large if an output current is large, please be careful about input-output differential voltage of the application.
Power Supply, GND pin (V+, PV+ and GND)
In line with switching element drive, current flows into the IC according to frequency. If the power supply
impedance provided to the power supply circuit is high, it will not be possible to take advantage of IC performance
due to input voltage fluctuation. Therefore insert a bypass capacitor close to the V+ pin – the GND pin connection in
order to lower high frequency impedance.
- 10 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
2. Additional and Protection Functions / Features
Under Voltage Lockout (UVLO)
The UVLO circuit operating is released above V+=3.4V(typ.) and IC operation starts. When power supply voltage
is low, IC does not operate because the UVLO circuit operates. There is 100mV width hysteresis voltage at rise and
decay of power supply voltage. Hysteresis prevents the malfunction at the time of UVLO operating and releasing.
Soft Start Function (Soft Start)
The output voltage of the converter gradually rises to a set value by the soft start function. The soft start time is
4ms (typ). It is defined with the time of the error amplifier reference voltage becoming from 0V to 0.75V. The soft start
circuit operates after the release UVLO and/or recovery from thermal shutdown. The operating frequency is
controlled with a low frequency, approximately 40% of the set value by the timing resistor, until voltage of the IN- pin
becomes approximately 0.4V.
0.8V
Vref,
IN- pin Voltage
FB pin Voltage
OSC Waveform
ON
SW pin
OFF
UVLO(3.4V typ.) Release,
Standby,
Recover from Thermal
Shutdow n
Low Frequency
Control
V IN-=approx 0.4V
Soft Start time: Tss=4ms(typ.) to V B=0.75V
Steady
Operaton
Soft Start effective period to V B=0.8V
Fig. 2. Startup Timing Chart
Ver.2013-01-23
- 11 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Description of Block Features (Continued)
Over Current Protection Circuit (OCP)
At when the switching current becomes ILIM or more, the overcurrent protection circuit is stopped the MOSFET
output. The switching output holds low level down to next pulse output at OCP operating.
The NJW4152 output returns automatically along with release from the over current condition because the
OCP is pulse-by-pulse type.
Fig.3. shows the timing chart of the over current protection detection.
If voltage of the IN- pin becomes less than 0.4V, the oscillation frequency decreases to approximately 40% and the
energy consumption is suppressed.
FB pin Voltage
OSC
Waveform
ON
SW pin
OFF
Sw itching
Current
ILIM
0
Static Status
Detect
Overcurrent
Static Status
Fig. 3. Timing Chart at Over Current Detection
Thermal Shutdown Function (TSD)
When Junction temperature of the NJW4152 exceeds the 175°C*, internal thermal shutdown circuit function stops
SW function. When junction temperature decreases to 145°C* or less, SW operation returns with soft start operation.
The purpose of this function is to prevent malfunctioning of IC at the high junction temperature. Therefore it is not
something that urges positive use. You should make sure to operate within the junction temperature range rated
(150°C). (* Design value)
ON/OFF Function (Standby Control)
The NJW4152 stops the operating and becomes standby status when the ON/OFF pin becomes less than 0.5V.
The ON/OFF pin internally pulls down with 480kΩ, therefore the NJW4152 becomes standby mode when the
ON/OFF pin is OPEN. You should connect this pin to V+ when you do not use ON/OFF function.
- 12 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
Application Information
Inductors
Current
Peak Current Ipk
Large currents flow into inductor, therefore you must
provide current capacity that does not saturate.
Inductor
(1) Continuous
Conduction Mode
Reducing L, the size of the inductor can be smaller. Current ∆IL
However, peak current increases and adversely
(2) Critical Mode
affecting efficiency.
(3) Continuous
On the other hand, increasing L, peak current can
0
Conduction Mode
be reduced at switching time. Therefore conversion
Frequency
tON
tOFF
fOSC
efficiency improves, and output ripple voltage reduces.
Above a certain level, increasing inductance windings
increases loss (copper loss) due to the resistor
Fig. 4. Inductor Current State Transition
element.
Ideally, the value of L is set so that inductance current is in continuous conduction mode. However, as the load
current decreases, the current waveform changes from (1) CCM: Continuous Conduction Mode → (2) Critical Mode
→ (3) DCM: Discontinuous Conduction Mode (Fig. 4.).
In discontinuous mode, peak current increases with respect to output current, and conversion efficiency tend to
decrease. Depending on the situation, increase L to widen the load current area to maintain continuous mode.
If the application needs maximum output current, the inductor ripple current should be set less than 20% to
prevent operating the over current protection circuit at the minimum switching limiting current.
Catch Diode
When the switch element is in OFF cycle, power stored in the inductor flows via the catch diode to the output
capacitor. Therefore during each cycle current flows to the diode in response to load current. Because diode's
forward saturation voltage and current accumulation cause power loss, a Schottky Barrier Diode (SBD), which has a
low forward saturation voltage, is ideal.
An SBD also has a short reverse recovery time. If the reverse recovery time is long, through current flows when
the switching transistor transitions from OFF cycle to ON cycle. This current may lower efficiency and affect such
factors as noise generation.
Input Capacitor
Transient current flows into the input section of a switching regulator responsive to frequency. If the power supply
impedance provided to the power supply circuit is large, it will not be possible to take advantage of the NJW4152
performance due to input voltage fluctuation. Therefore insert an input capacitor as close to the MOSFET as
possible.
Output Capacitor
An output capacitor stores power from the inductor, and stabilizes voltage provided to the output.
When selecting an output capacitor, you must consider Equivalent Series Resistance (ESR) characteristics, ripple
current, and breakdown voltage.
Also, the ambient temperature affects capacitors, decreasing capacitance and increasing ESR (at low
temperature), and decreasing lifetime (at high temperature). Concerning capacitor rating, it is advisable to allow
sufficient margin.
Output capacitor ESR characteristics have a major influence on output ripple noise. A capacitor with low ESR can
further reduce ripple voltage. Be sure to note the following points; when ceramic capacitor is used, the capacitance
value decreases with DC voltage applied to the capacitor.
Ver.2013-01-23
- 13 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Application Information (Continued)
Board Layout
In the switching regulator application, because the current flow corresponds to the oscillation frequency, the
substrate (PCB) layout becomes an important.
You should attempt the transition voltage decrease by making a current loop area minimize as much as possible.
Therefore, you should make a current flowing line thick and short as much as possible. Fig.5. shows a current loop
at step-down converter. Especially, should lay out high priority the loop of CIN-SW-SBD that occurs rapid current
change in the switching. It is effective in reducing noise spikes caused by parasitic inductance.
NJW4152
Built-in SW
V IN
CIN
NJW4152
Built-in SW
L
SBD
COUT
V IN
CIN
(a) Buck Converter SW ON
L
SBD
COUT
(b) Buck Converter SW OFF
Fig. 5. Current Loop at Buck Converter
Concerning the GND line, it is preferred to separate the power system and the signal system, and use single
ground point.
The voltage sensing feedback line should be as far away as possible from the inductance. Because this line has
high impedance, it is laid out to avoid the influence noise caused by flux leaked from the inductance.
Fig. 6. shows example of wiring at buck converter. Fig. 7 shows the PCB layout example.
L
PV +
V IN
V+
CIN
V OUT
SW
SBD
COUT
RL
(Bypass Capacitor)
NJW4152
RFB
RT
RT
CFB
INR2
GND
Separate Digital(Signal)
GND from Pow er GND
R1
To avoid the influence of the voltage
drop, the output voltage should be
detected near the load.
Because IN- pin is high impedance, the
voltage detection resistance: R1/R2 is
put as much as possible near IC(IN-).
Fig. 6. Board Layout at Buck Converter
- 14 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
Application Information (Continued)
GNDOUT
GND IN
Power GND Area
C IN1
C OUT
SBD
L
VIN
C IN2
ON/OFF
To
Signal GND
VOUT
RFB C FB
RT
RNF
R1
C NF
R2
Signal GND Area
Feed back signal
Connect Signal GND line and Power GND line on backside pattern
Fig. 7 Layout Example (upper view)
Ver.2013-01-23
- 15 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Calculation of Package Power
A lot of the power consumption of buck converter occurs from the internal switching element (Power MOSFET).
Power consumption of NJW4152 is roughly estimated as follows.
Input Power:
Output Power:
Diode Loss:
NJW4152 Power Consumption:
Where:
VIN
VOUT
VF
OFF duty
PIN = VIN × IIN [W]
POUT = VOUT × IOUT [W]
PDIODE = VF × IL(avg) × OFF duty [W]
PLOSS = PIN − POUT − PDIODE [W]
: Input Voltage for Converter
: Output Voltage of Converter
: Diode's Forward Saturation Voltage
: Switch OFF Duty
IIN
IOUT
IL(avg)
: Input Current for Converter
: Output Current of Converter
: Inductor Average Current
Efficiency (η) is calculated as follows.
η = (POUT ÷ PIN) × 100 [%]
You should consider temperature derating to the calculated power consumption: PD.
You should design power consumption in rated range referring to the power dissipation vs. ambient temperature
characteristics (Fig. 8).
NJW4152GM1-AB (HSOP8 Package)
Power Dissipation vs. Ambient Temperature
(Tj=~150°C)
3000
Power Dissipation PD (mW)
At on 4 layer PC Board
2500
2000
General
Spec
1500
At on 2 layer PC Board
1000
Extended
T1 spec
500
0
-50
-25
0
25
50
75
100
Ambient Temperature Ta (°C)
125
150
Mounted on glass epoxy board. (76.2×114.3×1.6mm:EIA/JDEC standard size, 2Layers)
Mounted on glass epoxy board. (76.2×114.3×1.6mm:EIA/JDEC standard size, 4Layers),
internal Cu area: 74.2×74.2mm
Fig. 8. Power Dissipation vs. Ambient Temperature Characteristics
- 16 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
Application Design Examples
Step-Down Application Circuit
IC
: NJW4152GM1
Input Voltage
: VIN=12V
Output Voltage
: VOUT=5V
Output Current
: IOUT=1A
Oscillation frequency : fosc=700kHz
Output Ripple Voltage : Vripple(P-P)=less than 20mV
CIN2
0.1µF/50V
CIN1
10µF/50V
V IN=12V
ONOFF
High: ON
Low: OFF
(Standby)
RT
27kΩ
4
RT
3
2
ON/OFF V +
1
PV +
NJW4152GM1
C1
open
IN-
FB
GND
SW
5
6
7
8
L 22µH/2.5A
SBD
RNF
3.3kΩ
CNF
4,700pF
COUT
4.7µF/6.3V
CFB
220pF
RFB
0Ω
V OUT =5V
R2
27kΩ
R1
5.1kΩ
IC
Reference
Qty.
1
L
1
CDRH8D28HPNP-220N
D
CIN1
CIN2
COUT
CNF
CFB
C1
R1
R2, RT
RNF
RFB
1
1
1
1
1
1
0
1
2
1
1
CMS11
UMK325BJ106MM
0.1µF
JMK212ABJ475KG
4,700pF
220pF
⎯ (Optional)
5.1kΩ
27kΩ
3.3kΩ
0Ω (Short)
Ver.2013-01-23
Part Number
NJW4152GM1
Description
Internal 1A MOSFET SW.REG. IC
Inductor 22µH,
2.5A(Ta=20°C) / 1.9A (Ta=100°C)
Schottky Diode 40V, 2A
Ceramic Capacitor 3225 10µF, 50V, X5R
Ceramic Capacitor 1608 0.1µF, 50V, B
Ceramic Capacitor 2012 4.7µF, 6.3V, X5R
Ceramic Capacitor 1608 4,700pF, 50V, B
Ceramic Capacitor 1608 220pF, 50V, CH
Optional
Resistor 1608 5.1kΩ, ±1%, 0.1W
Resistor 1608 27kΩ, ±1%, 0.1W
Resistor 1608 3.3kΩ, ±5%, 0.1W
Resistor 1608 0Ω, 0.1W
Manufacturer
New JRC
Sumida
Toshiba
Taiyo Yuden
Std.
Taiyo Yuden
Std.
Std.
⎯
Std.
Std.
Std.
Std.
- 17 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Application Design Examples (Continued)
Setting Oscillation Frequency
From the Oscillation frequency vs. Timing Resistor
Characteristic, RT=27 [kΩ], t=1.43[µs] at fosc=700kHz.
Step-down converter duty ratio is shown with the following
equation.
Duty =
VOUT + V F
5 + 0.4
× 100 =
× 100 = 45 [%]
12
V IN
Therefore, tON=0.64 [µs], tOFF=0.79 [µs]
Peak Current: Ipk
Inductance
Current: ∆IL
Output Current: IOUT
0
Period: t
Frequency: fOSC=1/t
tON
tOFF
Fig. 9. Inductor Current Waveform
Selecting Inductance
To assume maximum output current: 1A, and the inductor ripple current should be set not to exceed the minimum
switching limiting current: ILIM=1.4A (min.).
∆IL is Inductance ripple current. When to ∆IL= output current 20%:
∆IL = 0.2 × IOUT = 0.2 × 1 = 0.2 [A]
This obtains inductance L. VDS_RON is drop voltage by MOSFET on resistance.
L=
VIN − VDS − RON − VOUT
12 − 0.5 − 5
× tON =
× 0.64 µ = 20.8 [ µH ] ⇒ 22[µH]
∆I L
0 .2
Inductance L is a theoretical value. The optimum value varies according such factors as application specifications
and components. Fine-tuning should be done on the actual device.
This obtains the peak current Ipk at switching time.
Ipk = I OUT +
∆I L
0 .2
= 1+
= 1.1 [ A]
2
2
The current that flows into the inductance provides sufficient margin for peak current at switching time.
In the application circuit, use L=22µH, 2.5A(Ta=20°C) / 1.9A (Ta=100°C).
- 18 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
Application Design Examples (Continued)
Selecting the Input Capacitor
The input capacitor corresponds to the input of the power supply. It is required to adequately reduce the
impedance of the power supply. The input capacitor selection should be determined by the input ripple current and
the maximum input voltage of the capacitor rather than its capacitance value.
The effective input current can be expressed by the following formula.
I RMS = I OUT ×
VOUT × (V IN − VOUT )
V IN
[ A]
In the above formula, the maximum current is obtained when VIN = 2 × VOUT, and the result in this case is
IRMS = IOUT (MAX) ÷ 2.
When selecting the input capacitor, carry out an evaluation based on the application, and use a capacitor that has
adequate margin.
Selecting the Output Capacitor
The output capacitor is an important component that determines output ripple noise. Equivalent Series Resistance
(ESR), ripple current, and capacitor breakdown voltage are important in determining the output capacitor.
The output ripple noise can be expressed by the following formula.
ESR =
Vripple ( p − p )
∆I L
When selecting output capacitance, select a capacitor that allows for sufficient ripple current.
The effective ripple current that flows in a capacitor (Irms) is obtained by the following equation.
I rms =
∆I L
0.2
=
= 58 [ mArms ]
2 3 2 3
Consider sufficient margin, and use a capacitor that fulfills the above spec.
In the application circuit, use COUT=4.7µF/6.3V.
Setting Output Voltage
The output voltage VOUT is determined by the relative resistances of R1, R2. The current that flows in R1, R2 must
be a value that can ignore the bias current that flows in ER AMP.
⎛ 27k ⎞
⎛ R2 ⎞
VOUT = ⎜
+ 1⎟ × 0.8 = 5.04 [V ]
+ 1⎟ × V B = ⎜
R
1
⎝ 5.1k ⎠
⎝
⎠
Ver.2013-01-23
- 19 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
Compensation design example
A switching regulator requires a feedback circuit for acquiring a stable
output. Because the frequency characteristics of the application change
according to the inductance, output capacitor, and so on, the compensation
constant should ideally be determined in such a way that the maximum band
is acquired while the necessary phase for stable operation is maintained.
These compensation constants play an important role in the adjustment of
the NJW4152 when mounted in an actual unit. Finally, select the constants
while performing measurement, in consideration of the application
specifications.
Pole
Gain
-20dB/dec
Phase
0°
-45°
-90°
fP/10
fP
10fP
Frequency
Pole
+20dB/dec
Gain
Zero
+90°
Phase
Feedback and Stability
Basically, the feedback loop should be designed in such a way that the
open loop phase shift at the point where the loop gain is 0 dB is less than
-180°. It is also important that the loop characteristics have margin in
consideration of ringing and immunity to oscillation during load fluctuations.
With the NJW4152, the feedback circuit can be freely designed, enabling the
arrangement of the poles and zeros which is important for loop compensation,
to be optimized.
+45°
0°
fZ/10
fZ
10fZ
Frequency
Zero
The characteristics of the poles and zeros are shown in Fig. 10.
Poles: The gain has a slope of -20 dB/dec, and the phase shifts -90°.
Zeros: The gain has a slope of +20 dB/dec, and the phase shift +90°.
Fig. 10. Characteristics of Pole and Zero
If the number of factors constituting poles is defined as “n”, the change in the gain and phase will be “n”-fold. This
also applies to zeros as well. The poles and zeros are in a reciprocal relationship, so if there is one factor for each
pole and zero, they will cancel each other.
Configuration of the compensation circuit
PV
VIN
+
LC Gain
Buffer
SW
L
VOUT
RESR
CFB
R2
COUT
ER⋅AMP
PWM
CFB
Vref
=0.8V
RFB
IN-
FB
R1
CNF
RNF
C1(option)
Fig. 11. Compensation Circuit Configuration
- 20 -
Ver.2013-01-23
NJW4152-AB Application
Manual
NJW4152-AB
Technical Information
Compensation Design (Continued)
Poles and zeros due to the inductance and output capacitor
Double poles fP(LC) are generated by the inductance and output capacitor. Simultaneously, single zeros fZ(ESR) are
generated by the output capacitor and ESR. Each pole and zero is expressed by the following formula.
f Z(ESR ) =
1
fP(LC ) =
2πC OUTR ESR
1
2π LC OUT
If the ESR of the output capacitor is high, fZ(ESR) will be located in the vicinity of fP(LC). In an application such as this,
the zero fZ(ESR) compensates the double poles fP(LC), resulting in a tendency for stability to be readily maintained.
However, if the ESR of the output capacitor is low, fZ(ESR) shifts to the high region, and the phase is shifted -180° by
fP(LC).The NJW4152 compensation circuit enables compensation to be realized by using zeros fZ1 and fZ2.
Gain (dB)
Poles and zeros due to error amplifier
The single poles and zeros generated by the error amplifier
LC Gain
are obtained using the following formula.
Zero
Pole
1
fP1 =
1
fZ1 =
⎛ R1 R2 ⎞
Loop
2πCNF A V ⎜
⎟
2πCNFRNF
Gain
⎝ R1 + R2 ⎠
(Av: Amplifier Open Loop Gain=80dB)
fZ 2 =
1
2πCFBR2
fP 2 =
Double
pole
-40dB/dec
0dB frequency
* Gain increase
due to Zero
1
R1 R2 ⎞
⎛
2πC FB ⎜ R FB +
⎟
R1 + R2 ⎠
⎝
1
fP 3 =
2πC1 R NF
-20dB/dec
Compensation
Gain
(Option)
fZ1 and fZ2 are located on both sides of fP(LC).
Because the inductance and output capacitor vary, they are
each set using the following as a rough guide.
fP(LC) × 0.5-fold – 0.9-fold
fP(LC) × 1.1-fold – 2.0-fold
fP1
fZ1 or fZ2
fP(LC)
fP2 fP3 fZ(ESR)
Fig12. Loop Gain examples
There is also a method in which fZ1 and fZ2 are located at positions lower than even fP(LC). Because there is a
tendency for the phase shift to increase and the gain to rise, it can be expected that the response will improve.
However, there is a tendency for the phase margin to become insufficient, so care is necessary.
fP1 creates poles in the low frequency region due to the Miller effect of the error amplifier. The stability becomes
better as fP1 becomes lower. On the other hand, the frequency characteristics do not improve, so the response is
adversely affected. fP1 is set using a frequency gain of 20 dB for fP(LC) as a rough guide.
If the open loop gain of the error amplifier is made 80 dB, design is carried out using fP1 < fP(LC) ÷ 103 (= 60 dB) as a
rough guide.
Above several 100 kHz, various poles are generated, so the upper limit of the frequency range where the loop
gain is 0 dB is set to fifth (1/5) to tenth (1/10) of oscillation frequency. The fZ(ESR) in the high frequency region
sometimes causes a loop gain to be generated (See Fig.12 Loop Gain “). Using fP2 and fP3, perform adjustment with
the NJW4152 mounted in an actual unit, so as to adequately reduce the loop gain in the high frequency region.
Ver.2013-01-23
- 21 -
NJW4152-AB
NJW4152-ABApplication Manual
Technical Information
■Application Characteristics :NJW4152GM1-A
● At VOUT=5.0V setting (R1=5.1kΩ, R2=27kΩ, CFB=220pF, RFB=0Ω)
Efficiency vs. Output Current
Output Voltage vs. Output Current
o
(V)
f=700kHz
L=22µH
V =6V
IN
V =12V
IN
V =18V
IN
V =24V
IN
1
(Ta=25 C)
5.2
OUT
100
90
80
70
60
50
40
30
20
10
0
Output Voltage V
Efficiency η (%)
o
(VOUT=5.0V, Ta=25 C)
5.1
5.05
5
VIN=6V,12V, 18V, 24V
4.95
4.9
4.85
4.8
10
100
1000
Output Current IOUT (mA)
f=700kHz
L=22µH
5.15
1
10
100
1000
Output Current IOUT (mA)
● At VOUT=3.3V setting (R1=5.1kΩ, R2=16kΩ, CFB=220pF, RFB=0Ω)
Efficiency vs. Output Current
Output Voltage vs. Output Current
o
(VOUT=3.3V, Ta=25 C)
(V)
f=700kHz
L=22µH
V =5V
IN
V =12V
IN
V =18V
IN
V =24V
IN
1
(Ta=25 C)
3.36
OUT
100
90
80
70
60
50
40
30
20
10
0
Output Voltage V
Efficiency η (%)
o
3.32
3.3
VIN=5V,12V, 18V, 24V
3.28
3.26
3.24
10
100
1000
Output Current IOUT (mA)
f=700kHz
L=22µH
3.34
1
10
100
1000
Output Current IOUT (mA)
● At VOUT=1.5V setting (R1=30kΩ, R2=27kΩ, CFB=220pF, RFB=10kΩ)
Efficiency vs. Output Current
Output Voltage vs. Output Current
- 22 -
o
(VOUT=1.5V, Ta=25 C)
(V)
f=700kHz
L=22µH
V =5V
IN
V =12V
IN
V =18V
IN
V =24V
IN
1
(Ta=25 C)
1.56
OUT
100
90
80
70
60
50
40
30
20
10
0
10
100
1000
Output Current IOUT (mA)
Output Voltage V
Efficiency η (%)
o
f=700kHz
L=22µH
1.54
1.52
1.5
VIN=5V,12V, 18V, 24V
1.48
1.46
1.44
1
10
100
1000
Output Current IOUT (mA)
Ver.2013-01-23
NJW4152-AB
MEMO
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.
Ver.2013-01-23
- 23 -
Similar pages