ON NL17SZ06DFT2G Single inverter with open drain output Datasheet

NL17SZ06
Single Inverter with Open
Drain Outputs
The NL17SZ06 is a high performance single inverter with open
drain outputs operating from a 1.65 to 5.5 V supply.
The Output stage is open drain with Over Voltage Tolerance. This
allows the NL17SZ06 to be used to interface 5.0 V circuits to circuits
of any voltage between 0 and +7.0 V.
www.onsemi.com
MARKING
DIAGRAMS
Features
•
•
•
•
•
•
•
•
•
•
Tiny SOT−353 and SOT−553 Packages
Extremely High Speed: tPD 2.5 ns (typical) at VCC = 5.0 V
Designed for 1.65 V to 5.5 V VCC Operation, CMOS Compatible
Over Voltage Tolerant Inputs VIN may be Between 0 and 7.0 V for
VCC Between 0.5 and 5.5 V
TTL Compatible − Interface Capability with 5.0 V TTL Logic with
VCC = 2.7 V to 3.6 V
LVCMOS Compatible
24 mA Output Sink Capability, Pullup may be between 0 and 7.0 V
Near Zero Static Supply Current Substantially Reduces System
Power Requirements
Chip Complexity: FET = 20
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
5
LF MG
G
1
SOT−353/SC70−5/SC−88A
DF SUFFIX
CASE 419A
LF = Specific Device Marking
M = Date Code*
G
= Pb−Free Package
(Note: Microdot may be in either location)
*Date Code orientation and/or position may
vary depending upon manufacturing location.
5
5
1
LF M
SOT−553
XV5 SUFFIX
CASE 463B
NC
1
5
VCC
LF
M
OVT
IN A
GND
1
= Specific Device Marking
= Date Code
2
PIN ASSIGNMENT
3
4
1
Function
1
NC
2
IN A
3
GND
4
OUT Y
5
VCC
OUT Y
Figure 1. Pinout (Top View)
IN A
Pin
FUNCTION TABLE
OUT Y
Figure 2. Logic Symbol
A Input
Y Output
L
Z
H
L
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
December, 2015 − Rev. 9
1
Publication Order Number:
NL17SZ06/D
NL17SZ06
MAXIMUM RATINGS
Symbol
VCC
Characteristics
Value
Unit
−0.5 to +7.0
V
−0.5 ≤ VI ≤ +7.0
V
−0.5 ≤ VO ≤ 7.0
V
VI < GND
−50
mA
VO < GND
−50
mA
DC Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
IIK
DC Input Diode Current
IOK
DC Output Diode Current
IO
DC Output Sink Current
±50
mA
Output in Z or LOW State (Note 1)
ICC
DC Supply Current Per Supply Pin
±100
mA
IGND
DC Ground Current Per Ground Pin
±100
mA
TSTG
Storage Temperature Range
−65 to +150
°C
PD
Power Dissipation in Still Air
SOT−353
SOT−553
186
135
mW
qJA
Thermal Resistance
SOT−353
SOT−553
350
496
°C/W
TL
Lead Temperature, 1 mm from Case for 10 Seconds
260
°C
TJ
Junction Temperature Under Bias
+150
°C
±100
mA
ILatch−Up
Latchup Performance
MSL
Moisture Sensitivity
FR
Flammability Rating
ESD
ESD Classification
Above VCC and Below GND at 85°C (Note 5)
Level 1
Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
Human Body Model (Note 3)
Machine Model (Note 4)
Charged Device Model (Note 5)
2000
200
N/A
V
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. IO absolute maximum rating must be observed.
2. Tested to EIA/JESD22−A114−A, rated to EIA/JESD22−A114−B.
3. Tested to EIA/JESD22−A115−A, rated to EIA/JESD22−A115−A.
4. Tested to JESD22−C101−A.
5. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
VI
Input Voltage
VO
Output Voltage
TA
Operating Free−Air Temperature
Dt/DV
Input Transition Rise or Fall Rate
Operating
Data Retention Only
(Z or LOW State)
VCC = 2.5 V ±0.2 V
VCC = 3.0 V ±0.3 V
VCC = 5.0 V ±0.5 V
Min
Max
Unit
1.65
1.5
5.5
5.5
V
0
5.5
V
0
5.5
V
−55
+125
°C
0
0
0
20
10
5
ns/V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
2
NL17SZ06
DC ELECTRICAL CHARACTERISTICS
Min
0.75 VCC
0.7 VCC
Typ
Max
Min
Max
Symbol
Parameter
VIH
High−Level Input Voltage
1.65 to 1.95
2.3 to 5.5
VIL
Low−Level Input Voltage
1.65 to 1.95
2.3 to 5.5
0.25 VCC
0.3 VCC
0.25 VCC
0.3 VCC
V
ILKG
Z−State Output
Leakage Current
VIN = VIL
VOUT = VCC or GND
2.3 to 5.5
±5.0
±10.0
mA
VOL
Low−Level Output
Voltage
VIN = VIH or VIL
IOL = 100 mA
1.65 to 5.5
0.0
0.1
0.1
V
IOL = 4 mA
1.65
0.08
0.24
0.24
IOL = 8 mA
2.3
0.22
0.3
0.3
IOL = 12 mA
2.7
0.22
0.4
0.4
IOL = 16 mA
3.0
0.28
0.4
0.4
IOL = 24 mA
3.0
0.38
0.55
0.55
IOL = 32 mA
4.5
0.42
0.55
0.55
VIN = 5.5 V or GND
0 to 5.5
±0.1
±1.0
mA
VIN = 5.5 V or
VOUT = 5.5 V
0
1.0
10
mA
VIN = 5.5 V or GND
5.5
1.0
10
mA
IIN
Condition
−55°C ≤ TA ≤ 125°C
TA = 25°C
VCC
(V)
Input Leakage Current
IOFF
Power Off
Leakage Current
ICC
Quiescent Supply Current
0.75 VCC
0.7 VCC
Unit
V
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
AC ELECTRICAL CHARACTERISTICS tR = tF = 2.5 ns; CL = 50 pF; RL = 500 W
−55°C ≤ TA ≤ 125°C
TA = 25°C
Symbol
tPZL
tPLZ
Condition
VCC (V)
Min
Typ
Max
Min
Max
Unit
RL = R1= 500 W, CL = 50 pF
1.65
0.8
5.3
11.6
0.8
12.0
ns
2.5 ± 0.2
0.8
3.0
3.6
0.8
4.1
3.3 ± 0.3
0.8
2.4
3.2
0.8
3.7
5.0 ± 0.5
0.5
2.4
3.0
0.5
3.5
1.65
0.8
5.3
11.6
0.8
12.0
2.5 ± 0.2
0.8
2.5
3.6
0.8
4.1
3.3 ± 0.3
0.8
2.1
3.2
0.8
3.7
5.0 ± 0.5
0.5
1.2
3.0
0.5
3.5
Parameter
Propagation Delay
(Figure 3 and 4)
Propagation Delay
(Figure 3 and 4)
RL = R1= 500 W, CL = 50 pF
ns
CAPACITIVE CHARACTERISTICS
Symbol
CIN
Parameter
Input Capacitance
COUT
Output Capacitance
CPD
Power Dissipation Capacitance (Note 6)
Condition
Typical
Unit
VCC = 5.5 V, VI = 0 V or VCC
u2.5
pF
VCC = 5.5 V, VI = 0 V or VCC
4.0
pF
10 MHz, VCC = 5.5 V, VI = 0 V or VCC
4.0
pF
6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic
power consumption; PD = CPD VCC2 fin + ICC VCC.
www.onsemi.com
3
NL17SZ06
VCC
A
50%
GND
tPZL
Y
tPLZ
50% VCC
HIGH
IMPEDANCE
VOL +0.3 V
Figure 3. Switching Waveforms
VCC
R1
PULSE
GENERATOR
VCC x 2
DUT
RT
CL
RL
RT = ZOUT of pulse generator (typically 50 W)
Figure 4. Test Circuit
DEVICE ORDERING INFORMATION
Device
Order Number
Package Type
Tape and Reel Size†
NL17SZ06DFT2G
SOT−353/SC70−5/SC−88A
(Pb−Free)
3000 / Tape & Reel
NL17SZ06XV5T2G
SOT−553
(Pb−Free)
4000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
4
NL17SZ06
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
M
B
M
N
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
J
C
K
H
SOLDER FOOTPRINT*
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
5
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
NL17SZ06
PACKAGE DIMENSIONS
SOT−553
XV5 SUFFIX
CASE 463B
ISSUE C
D
−X−
5
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM
THICKNESS OF BASE MATERIAL.
A
L
4
1
2
E
−Y−
3
b
e
HE
c
5 PL
0.08 (0.003)
M
MILLIMETERS
NOM
MAX
0.55
0.60
0.22
0.27
0.13
0.18
1.60
1.65
1.20
1.25
0.50 BSC
0.10
0.20
0.30
1.55
1.60
1.65
DIM
A
b
c
D
E
e
L
HE
X Y
MIN
0.50
0.17
0.08
1.55
1.15
INCHES
NOM
0.022
0.009
0.005
0.063
0.047
0.020 BSC
0.004
0.008
0.061
0.063
MIN
0.020
0.007
0.003
0.061
0.045
MAX
0.024
0.011
0.007
0.065
0.049
0.012
0.065
RECOMMENDED
SOLDERING FOOTPRINT*
0.3
0.0118
0.45
0.0177
1.35
0.0531
1.0
0.0394
0.5
0.5
0.0197 0.0197
SCALE 20:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NL17SZ06/D
Similar pages