Fairchild NM24C04FLZN 4k-bit standard 2-wire bus interface serial eeprom Datasheet

NM24C04/05 – 4K-Bit Standard 2-Wire Bus
Interface Serial EEPROM
General Description
Features
The NM24C04/05 devices are 4096 bits of CMOS non-volatile
electrically erasable memory. These devices conform to all specifications in the Standard IIC 2-wire protocol and are designed to
minimize device pin count, and simplify PC board layout requirements.
■ Extended operating voltage 2.7V – 5.5V
■ 400 KHz clock frequency (F) at 2.7V - 5.5V
■ 200µA active current typical
10µA standby current typical
1µA standby current typical (L)
0.1µA standby current typical (LZ)
The upper half (upper 2Kbit) of the memory of the NM24C05 can be
write protected by connecting the WP pin to VCC. This section of
memory then becomes unalterable unless WP is switched to VSS.
■ IIC compatible interface
– Provides bi-directional data transfer protocol
■ Schmitt trigger inputs
This communications protocol uses CLOCK (SCL) and DATA
I/O (SDA) lines to synchronously clock data between the master
(for example a microprocessor) and the slave EEPROM device(s).
The Standard IIC protocol allows for a maximum of 16K of
EEPROM memory which is supported by the Fairchild family in
2K, 4K, 8K, and 16K devices, allowing the user to configure the
memory as the application requires with any combination of
EEPROMs. In order to implement higher EEPROM memory
densities on the IIC bus, the Extended IIC protocol must be used.
(Refer to the NM24C32 or NM24C65 datasheets for more information.)
■ Sixteen byte page write mode
– Minimizes total write time per byte
■ Self timed write cycle
Typical write cycle time of 6ms
■ Hardware Write Protect for upper half (NM24C05 only)
■ Endurance: 1,000,000 data changes
■ Data retention greater than 40 years
■ Packages available: 8-pin DIP, 8-pin SO, and 8-pin TSSOP
■ Available in three temperature ranges
- Commercial: 0° to +70°C
- Extended (E): -40° to +85C
- Automotive (V): -40° to +125°C
Fairchild EEPROMs are designed and tested for applications requiring high endurance, high reliability and low power consumption.
Block Diagram
VCC
VSS
WP
H.V. GENERATION
TIMING &CONTROL
START
STOP
LOGIC
SDA
CONTROL
LOGIC
SLAVE ADDRESS
REGISTER &
COMPARATOR
SCL
XDEC
A2
A1
E2PROM
ARRAY
WORD
ADDRESS
COUNTER
R/W
YDEC
CK
DATA REGISTER
DIN
DOUT
DS500070-1
© 1998 Fairchild Semiconductor Corporation
NM24C04/05 Rev. G
1
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
February 2000
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Connection Diagrams
Dual-in-Line Package (N), SO Package (M8) and TSSOP Package (MT8)
NC
1
A1
2
8
VCC
7
NC
NM24C04
A2
3
6
SCL
VSS
4
5
SDA
DS500070-2
See Package Number N08E, M08A and MTC08
Pin Names
A1,A2
Device Address Inputs
VSS
Ground
SDA
Serial Data I/O
SCL
Serial Clock Input
NC
No Connection
VCC
Power Supply
Dual-in-Line Package (N), SO Package (M8) and TSSOP Package (MT8)
NC
1
A1
2
8
VCC
7
WP
NM24C05
A2
3
6
SCL
VSS
4
5
SDA
DS500070-3
See Package Number N08E, M08A and MTC08
Pin Names
A1,A2
Device Address Inputs
VSS
Ground
SDA
Serial Data I/O
SCL
Serial Clock input
WP
Write Protect
VCC
Power Supply
NC
No Connection
2
NM24C04/05 Rev. G
www.fairchildsemi.com
NM
24
C
XX
F
LZ
E
XXX
Letter
Description
N
M8
MT8
8-pin DIP
8-pin SOIC
8-pin TSSOP
Temp. Range
None
V
E
0 to 70°C
-40 to +125°C
-40 to +85°C
Voltage Operating Range
Blank
L
LZ
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V and
<1µA Standby Current
SCL Clock Frequency
Blank
F
100KHz
400KHz
04
05
4K
4K with Write Protect
C
CMOS Technology
24
IIC
NM
Fairchild Non-Volatile
Memory
Package
Density
Interface
3
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Ordering Information
Operating Conditions
Absolute Maximum Ratings
Ambient Storage Temperature
Ambient Operating Temperature
NM24C04/05
NM24C04E/05E
NM24C04V/05V
–65°C to +150°C
All Input or Output Voltages
with Respect to Ground
6.5V to –0.3V
Lead Temperature
(Soldering, 10 seconds)
+300°C
ESD Rating
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
Positive Power Supply
NM24C04/05
NM24C04L/05L
NM24C04LZ/05LZ
2000V min.
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V
DC Electrical Characteristics (2.7V to 5.5V)
Symbol
Parameter
Test Conditions
Min
Limits
Typ
(Note 1)
Max
Units
ICCA
Active Power Supply Current
fSCL = 400 KHz
fSCL = 100 KHz
0.2
1.0
mA
ISB
Standby Current
VIN = GND
or VCC
10
1
0.1
50
10
1
µA
µA
µA
ILI
Input Leakage Current
VIN = GND to VCC
0.1
1
µA
ILO
Output Leakage Current
VOUT = GND to VCC
0.1
1
µA
VCC = 2.7V - 5.5V
VCC = 2.7V - 5.5V (L)
VCC = 2.7V - 4.5V (LZ)
VIL
Input Low Voltage
–0.3
VCC x 0.3
V
VIH
Input High Voltage
VCC x 0.7
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
IOL = 3 mA
Capacitance TA = +25°C, f = 100/400 KHz, VCC = 5V (Note 2)
Symbol
Conditions
Max
Units
CI/O
Input/Output Capacitance (SDA)
Test
VI/O = 0V
8
pF
CIN
Input Capacitance (A0, A1, A2, SCL)
VIN = 0V
6
pF
Note 1: Typical values are TA = 25°C and nominal supply voltage of 5V for 4.5V-5.5V operation and at 3V for 2.7V-4.5V operation.
Note 2: This parameter is periodically sampled and not 100% tested.
4
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Product Specifications
AC Testing Input/Output Waveforms
Input Pulse Levels
VCC x 0.1 to VCC x 0.9
0.9VCC
0.7VCC
Input Rise and Fall Times
10 ns
0.1VCC
0.3VCC
Input & Output Timing Levels
VCC x 0.3 to VCC x 0.7
Output Load
1 TTL Gate and CL = 100 pF
DS500070-4
Read and Write Cycle Limits (Standard and Low VCC Range 2.7V - 5.5V)
Symbol
fSCL
TI
Parameter
100 KHz
Min
Max
400 KHz
Min
Max
Units
SCL Clock Frequency
100
400
KHz
Noise Suppression Time Constant at
SCL, SDA Inputs (Minimum VIN
Pulse width)
100
50
ns
0.9
µs
tAA
SCL Low to SDA Data Out Valid
0.3
3.5
0.1
tBUF
Time the Bus Must Be Free before
a New Transmission Can Start
4.7
1.3
µs
Start Condition Hold Time
4.0
0.6
µs
tLOW
Clock Low Period
4.7
1.5
µs
tHIGH
Clock High Period
4.0
0.6
µs
tSU:STA
Start Condition Setup Time
(for a Repeated Start Condition)
4.7
0.6
µs
tHD:DAT
Data in Hold Time
20
20
ns
tSU:DAT
Data in Setup Time
250
100
ns
tHD:STA
tR
SDA and SCL Rise Time
1
0.3
µs
tF
SDA and SCL Fall Time
300
300
ns
tSU:STO
tDH
tWR
(Note 3)
Stop Condition Setup Time
4.7
Data Out Hold Time
300
µs
0.6
50
Write Cycle Time - NM24C04/05
- NM24C04/05L, NM24C04/05LZ
ns
10
15
10
15
ms
Note 3: The write cycle time (tWR) is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, the
NM24C04/05 bus interface circuits are disabled, SDA is allowed to remain high per the bus-level pull-up resistor, and the device does not respond to its slave address. Refer
"Write Cycle Timing" diagram.
Bus Timing
tR
tF
tHIGH
tLOW
tLOW
SCL
;;
tSU:STA
SDA
tHD:STA
tHD:DAT
tSU:DAT
IN
tSU:STO
tBUF
tAA
tDH
SDA
OUT
DS500070-5
5
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
AC Test Conditions
SCL
SDA
8th BIT
ACK
WORD n
tWR
STOP
CONDITION
Note:
START
CONDITION
The write cycle time (tWR) is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle.
DS500070-6
Typical System Configuration
VCC
VCC
SDA
SCL
Master
Transmitter/
Receiver
Note:
Slave
Transmitter/
Receiver
Slave
Receiver
Master
Transmitter/
Receiver
Master
Transmitter
DS500070-7
Due to open drain configuration of SDA and SCL, a bus-level pull-up resistor is called for, (typical value = 4.7kΩ)
Example of 16K of Memory on 2-Wire Bus
Note:
The SDA pull-up resistor is required due to the open-drain/open collector output of IIC bus devices.
The SCL pull-up resistor is recommended because of the normal SCL line inactive 'high' state.
It is recommended that the total line capacitance be less than 400pF
VCC
VCC
SDA
SCL
VCC
VCC
VCC
VCC
NM24C02/03
NM24C02/03
NM24C04/05
NM24C08/09
A0 A1 A2 VSS
A0 A1 A2 VSS
A1 A2 VSS
A2 VSS
To To To
VSS VSS VSS
Device
To To To
VCC VSS VSS
To To
VCC VSS
To
VCC
A0
Address Pins Present
A1
A2
NM24C02/03
Yes
Yes
NM24C04/05
No
NM24C08/09
NM24C16/17
Memory Size
# of Page
Blocks
Yes
2048 Bits
1
Yes
Yes
4096 Bits
2
No
No
Yes
8192 Bits
4
No
No
No
16,384 Bits
8
6
NM24C04/05 Rev. G
DS500070-8
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Write Cycle Timing
Acknowledge
IIC bus allows synchronous bi-directional communication between a TRANSMITTER and a RECEIVER using a Clock signal
(SCL) and a Data signal (SDA). Additionally there are up to three
Address signals (A2, A1 and A0) which collectively serve as "chip
select signal" to a device (example EEPROM) on the IIC bus.
Acknowledge is an active LOW pulse on the SDA line driven by an
addressed receiver to the addressing transmitter to indicate
receipt of 8-bits of data. The receiver provides an ACK pulse for
every 8-bits of data received. This handshake mechanism is done
as follows: After transmitting 8-bits of data, the transmitter releases the SDA line and waits for the ACK pulse. The addressed
receiver, if present, drives the ACK pulse on the SDA line during
the 9th clock and releases the SDA line back (to the transmitter).
Refer Figure 3.
All communication on the IIC bus must be started with a valid
START condition (by a MASTER), followed by transmittal (by the
MASTER) of byte(s) of information (Address/Data). For every byte
of information received, the addressed RECEIVER provides a valid
ACKNOWLEDGE pulse to further continue the communication
unless the RECEIVER intends to discontinue the communication.
Depending on the direction of transfer (Write or Read), the RECEIVER can be a SLAVE or the MASTER. A typical IIC communication concludes with a STOP condition (by the MASTER).
Array Address
Array address is an 8-bit information containing the address of a
memory location to be selected within a page block of the device.
16K bit Addressing Limitation:
Addressing an EEPROM memory location involves sending a
command string with the following information:
Standard IIC specification limits the maximum size of EEPROM
memory on the bus to 16K bits. This limitation is due to the
addressing protocol implemented which consists of the 8-bit Slave
Address and an additional 8-bit field called Array Address. This
Array Address selects 1 out of 256 locations (28=256). Since the
data format of IIC specification is 8-bit wide, a total of 256 x 8 =
2048 = 2K bit now becomes addressable by this 8-bit Array
Address. This 2K bit is typically referred as a “Page Block”.
Combining this 8-bit Array Address with the 3-bit Device/Page
address (part of Slave Address) allows a maximum of 8 pages
(23=8) of memory that can be addressed. Since each page is 2K
bit in size, 8 x 2K bit = 16K bit is the maximum size of memory that
is addressable on the Standard IIC bus. This 16Kb of memory can
be in the form of a single 16Kb EEPROM device or multiple
EEPROMs of varying density (in 2Kb multiples) to a maximum
total of 16Kb. To address the needs of systems that require more
than 16Kb on the IIC bus, a different specification called “Extended IIC Specification” is used. Please refer to NM24C32xx
Datasheet for more information on Extended IIC Specification.
[DEVICE TYPE]—[DEVICE/PAGE BLOCK SELECTION]—[R/W
BIT]—{acknowledge pulse}—[ARRAY ADDRESS]
Slave Address
Slave Address is an 8-bit information consisting of a Device type
field (4bits), Device/Page block selection field (3bits) and Read/
Write bit (1bit).
Slave Address Format
Device Type
Identifier
1
0
1
Device/Page Block
Selection
0
A2
A1
A0
R/W
(LSB)
DS500070-9
DEFINITIONS
Device Type
IIC bus is designed to support a variety of devices such as RAMs,
EPROMs etc., along with EEPROMS. Hence to properly identify
various devices on the IIC bus, a 4-bit “Device Type” identifier
string is used. For EEPROMS, this 4-bit string is 1-0-1-0. Every IIC
device on the bus internally compares this 4-bit string to its own
“Device Type” string to ensure proper device selection.
WORD
8 bits (byte) of data
PAGE
16 sequential byte locations
starting at a 16-byte address
boundary, that may be programmed during a "page write"
programming cycle
Device/Page Block Selection
PAGE BLOCK
2048 (2K) bits organized into 16
pages of addressable memory. (8
bits) x (16 bytes) x (16 pages) =
2048 bits
MASTER
Any IIC device CONTROLLING the
transfer of data (such as a
microprocessor)
SLAVE
Device being controlled
(EEPROMs are always considered
Slaves)
TRANSMITTER
Device currently SENDING data on
the bus (may be either a Master or
Slave).
RECEIVER
Device currently RECEIVING data
on the bus (Master or Slave)
When multiple devices of the same type (e.g. multiple EEPROMS)
are present on the IIC bus, then the A2, A1 and A0 address
information bits are also used as part of the Slave Address. Every
IIC device on the bus internally compares this 3-bit string to its own
physical configuration (A2, A1 and A0 pins) to ensure proper
device selection. This comparison is in addition to the “Device
Type” comparison. In addition to selecting an EEPROM, these 3
bits are also used to select a “page block” within the selected
EEPROM. Each page block is 2Kbit (256Bytes) in size. Depending on the density, an EEPROM can contain from a minimum of 1
to a maximum of 8 page blocks (in multiples of 2) and selection of
a page block within a device is by using A2, A1 and A0 bits.
Read/Write Bit
Last bit of the Slave Address indicates if the intended access is
Read or Write. If the bit is "1," then the access is Read, whereas
if the bit is "0," then the access is Write.
7
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Background Information (IIC Bus)
Device Operation
Serial Clock (SCL)
SDA is a bi-directional pin used to transfer data into and out of the
device. It is an open drain output and may be wire–ORed with any
number of open drain or open collector outputs.
The NM24C04/05 supports a bi-directional bus oriented protocol.
The protocol defines any device that sends data onto the bus as
a transmitter and the receiving device as the receiver. The device
controlling the transfer is the master and the device that is
controlled is the slave. The master will always initiate data
transfers and provide the clock for both transmit and receive
operations. Therefore, the NM24C04/05 will be considered a
slave in all applications.
Write Protect (WP) (NM24C05 Only)
Clock and Data Conventions
If tied to VCC, PROGRAM operations onto the upper half (upper
2Kbit) of the memory will not be executed. READ operations are
possible. If tied to VSS, normal operation is enabled, READ/
WRITE over the entire memory is possible.
Data states on the SDA line can change only during SCL LOW.
SDA state changes during SCL HIGH are reserved for indicating
start and stop conditions. Refer to Figure 1 and Figure 2 on next
page.
This feature allows the user to assign the upper half of the memory
as ROM which can be protected against accidental programming.
When write is disabled, slave address and word address will be
acknowledged but data will not be acknowledged.
Start Condition
The SCL input is used to clock all data into and out of the device.
Serial Data (SDA)
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The NM24C04/
05 continuously monitors the SDA and SCL lines for the start
condition and will not respond to any command until this condition
has been met.
This pin has an internal pull-down circuit. However, on systems
where write protection is not required it is recommended that this
pin is tied to VSS.
Stop Condition
Device Selection Inputs A2, A1 and A0 (as
appropriate)
All communications are terminated by a stop condition, which is a
LOW to HIGH transition of SDA when SCL is HIGH. The stop
condition is also used by the NM24C04/05 to place the device in
the standby power mode, except when a Write operation is being
executed, in which case a second stop condition is required after
tWR period, to place the device in standby mode.
These inputs collectively serve as “chip select” signal to an
EEPROM when multiple EEPROMs are present on the same IIC
bus. Hence these inputs, if present, should be connected to VCC
or VSS in a unique manner to allow proper selection of an EEPROM
amongst multiple EEPROMs. During a typical addressing sequence, every EEPROM on the IIC bus compares the configuration of these inputs to the respective 3 bit “Device/Page block
selection” information (part of slave address) to determine a valid
selection. For e.g. if the 3 bit “Device/Page block selection” is 10-1, then the EEPROM whose “Device Selection inputs” (A2, A1
and A0) are connected to VCC-VSS-VCC respectively, is selected.
Depending on the density, only appropriate number of “Device
Selection inputs” are provided on an EEPROM. For every “Device
selection input” that is not present on the device, the corresponding bit in the “Device/Page block selection” field is used to select
a “Page Block” within the device instead of the device itself.
Following table illustrates the above:
EEPROM
Density
Number of
Page Blocks
Device Selection Inputs
Provided
Address Bits
Selecting Page Block
2k bit
1
A0
A1
A2
None
4k bit
2
—
A1
A2
A0
8k bit
4
—
—
A2
A0 and A1
16k bit
8
—
—
—
A0, A1 and A2
Note that even when just one EEPROM present on the IIC bus,
these pins should be tied to VCC or VSS to ensure proper termination.
8
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Pin Descriptions
SCL
SDA
DATA STABLE
DATA
CHANGE
DS500070-10
Start and Stop Definition (Figure 2)
SCL
SDA
START
CONDITION
STOP
CONDITION
DS500070-11
Acknowledge Response from Receiver (Figure 3)
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM
TRANSMITTER
tDH
tAA
DATA OUTPUT
FROM
RECEIVER
START
CONDITION
ACKNOWLEDGE
PULSE
DS500070-12
9
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Data Validity (Figure 1)
Refer the following table for Slave Addresses string details:
The NM24C04/05 device will always respond with an acknowledge after recognition of a start condition and its slave address. If
both the device and a write operation have been selected, the
NM24C04/05 will respond with an acknowledge after the receipt
of each subsequent eight bit byte.
Device
NM24C04/05
NM24C04/05
1
A2
A1
A0
R/W
0, 1
A simple review: After the NM24C04/05 recognizes the start
condition, the devices interfaced to the IIC bus wait for a slave
address to be transmitted over the SDA line. If the transmitted
slave address matches an address of one of the devices, the
designated slave pulls the line LOW with an acknowledge signal
and awaits further transmissions.
(LSB)
Page
Block Address
10
NM24C04/05 Rev. G
2
The last bit of the slave address defines whether a write or read
condition is requested by the master. A '1' indicates that a read
operation is to be executed, and a '0' initiates the write mode.
Device
Address
0
A
All IIC EEPROMs use an internal protocol that defines a PAGE
BLOCK size of 2K bits (for Word addresses 0x00 through 0xFF).
Therefore, address bits A0, A1, or A2 (if designated 'P') are used
to access a PAGE BLOCK in conjunction with the Word address
used to access any individual data byte.
Following a start condition the master must output the address of
the slave it is accessing. The most significant four bits of the slave
address are those of the device type identifier. This is fixed as
1010 for all EEPROM devices.
0
A
P: Refers to an internal PAGE BLOCK.
Device Addressing
1
P
Page Block
Addresses
A: Refers to a hardware configured Device Address pin.
In the read mode the NM24C04/05 slave will transmit eight bits of
data, release the SDA line and monitor the line for an acknowledge. If an acknowledge is detected, NM24C04/05 will continue
to transmit data. If an acknowledge is not detected,NM24C04/05
will terminate further data transmissions and await the stop
condition to return to the standby power mode.
Device Type
Identifier
A0 A1 A2 Page
Blocks
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Acknowledge
Page Write is initiated in the same manner as the Byte Write
operation; but instead of terminating the cycle after transmitting
the first data byte, the master can further transmit up to 15 more
bytes. After the receipt of each byte, NM24C04/05 will respond
with an acknowledge pulse, increment the internal address counter
to the next address and is ready to accept the next data. If the
master should transmit more than sixteen bytes prior to generating the STOP condition, the address counter will “roll over” and
previously written data will be overwritten. As with the Byte Write
operation, all inputs are disabled until completion of the internal
write cycle. Refer to Figure 5 for the address, acknowledge and
data transfer sequence.
BYTE WRITE
For a write operation a second address field is required which is
a word address that is comprised of eight bits and provides access
to any one of the 256 bytes in the selected page of memory. Upon
receipt of the byte address the NM24C04/05 responds with an
acknowledge and waits for the next eight bits of data, again,
responding with an acknowledge. The master then terminates the
transfer by generating a stop condition, at which time the NM24C04/
05 begins the internal write cycle to the nonvolatile memory. While
the internal write cycle is in progress the NM24C04/05 inputs are
disabled, and the device will not respond to any requests from the
master for the duration of tWR. Refer to Figure 4 for the address,
acknowledge and data transfer sequence.
Acknowledge Polling
Once the stop condition is issued to indicate the end of the host’s
write operation the NM24C04/05 initiates the internal write cycle.
ACK polling can be initiated immediately. This involves issuing the
start condition followed by the slave address for a write operation.
If the NM24C04/05 is still busy with the write operation no ACK will
be returned. If the NM24C04/05 has completed the write operation
an ACK will be returned and the host can then proceed with the
next read or write operation.
PAGE WRITE
To minimize write cycle time, NM24C04/05 offer Page Write
feature, by which, up to a maximum of 16 contiguous bytes
locations can be programmed all at once (instead of 16 individual
byte writes). To facilitate this feature, the memory array is organized in terms of “Pages.” A Page consists of 16 contiguous byte
locations starting at every 16-Byte address boundary (for example, starting at array address 0x00, 0x10, 0x20 etc.). Page
Write operation limits access to byte locations within a page. In
other words a single Page Write operation will not cross over to
locations on another page but will “roll over” to the beginning of the
page whenever end of Page is reached and additional locations
are a continued to be accessed. A Page Write operation can be
initiated to begin at any location within a page (starting address of
the Page Write operation need not be the starting address of a
Page).
Write Protection (NM24C05 Only)
Programming of the upper half (upper 2Kbit) of the memory will not
take place if the WP pin of the NM24C05 is connected to VCC. The
NM24C05 will respond to slave and byte addresses; but if the
memory accessed is write protected by the WP pin, the NM24C05
will not generate an acknowledge after the first byte of data has
been received, and thus the program cycle will not be started when
the stop condition is asserted.
Byte Write (Figure 4)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
WORD
ADDRESS
S
T
O
P
DATA
SDA Line
A
C
K
Bus Activity:
EEPROM
A
C
K
A
C
K
DS500070-13
Page Write (Figure 5)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
WORD ADDRESS (n)
DATA n
DATA n + 1
S
T
O
P
DATA n + 15
SDA Line
Bus Activity:
EEPROM
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
DS500070-14
11
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Write Operations
master immediately issues another start condition and the slave
address with the R/W bit set to one. This will be followed by an
acknowledge from the NM24C04/05 and then by the eight bit byte.
The master will not acknowledge the transfer but does generate
the stop condition, and therefore the NM24C04/05 discontinues
transmission. Refer to Figure 7 for the address, acknowledge and
data transfer sequence.
Read operations are initiated in the same manner as write
operations, with the exception that the R/W bit of the slave
address is set to a one. There are three basic read operations:
current address read, random read, and sequential read.
Current Address Read
Sequential Read
Internally the NM24C04/05 contains an address counter that
maintains the address of the last byte accessed, incremented by
one. Therefore, if the last access (either a read or write) was to
address n, the next read operation would access data from
address n + 1. Upon receipt of the slave address with R/W set to
one, the NM24C04/05 issues an acknowledge and transmits the
eight bit byte. The master will not acknowledge the transfer but
does generate a stop condition, and therefore the NM24C04/05
discontinues transmission. Refer to Figure 6 for the sequence of
address, acknowledge and data transfer.
Sequential reads can be initiated as either a current address read
or random access read. The first word is transmitted in the same
manner as the other read modes; however, the master now
responds with an acknowledge, indicating it requires additional
data. The NM24C04/05 continues to output data for each acknowledge received. The read operation is terminated by the
master not responding with an acknowledge or by generating a
stop condition.
The data output is sequential, with the data from address n
followed by the data from n + 1. The address counter for read
operations increments all word address bits, allowing the entire
memory contents to be serially read during one operation. After
the entire memory has been read, the counter "rolls over" to the
beginning of the memory. NM24C04/05 continues to output data
for each acknowledge received. Refer to Figure 8 for the address,
acknowledge, and data transfer sequence.
Random Read
Random read operations allow the master to access any memory
location in a random manner. Prior to issuing the slave address
with the R/W bit set to one, the master must first perform a
“dummy” write operation. The master issues the start condition,
slave address with the R/W bit set to zero and then the byte
address it is to read. After the byte address acknowledge, the
Current Address Read (Figure 6)
Bus Activity:
Master
SDA Line
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
1 0 1 0
1
A
C
K
Bus Activity:
EEPROM
DATA
NO
A
C
K
DS500070-15
Random Read (Figure 7)
Bus Activity:
Master
S
T
A
R
T
SLAVE
ADDRESS
S
T
A
R
T
WORD
ADDRESS
S
T
O
P
SLAVE
ADDRESS
SDA Line
A
C
K
Bus Activity:
EEPROM
A
C
K
A
C
K
DATA n
NO
A
C
K
DS500070-16
Sequential Read (Figure 8)
Bus Activity:
Master
A
C
K
Slave
Address
S
T
O
P
A
C
K
A
C
K
SDA Line
Bus Activity:
EEPROM
A
C
K
DATA n +1
DATA n +1
DATA n + 2
DATA n + x
NO
A
C
K
DS500070-17
12
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Read Operations
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Physical Dimensions inches (millimeters) unless otherwise noted
0.189 - 0.197
(4.800 - 5.004)
8 7 6 5
0.228 - 0.244
(5.791 - 6.198)
1 2 3 4
Lead #1
IDENT
0.150 - 0.157
(3.810 - 3.988)
0.010 - 0.020
x 45°
(0.254 - 0.508)
0.0075 - 0.0098
(0.190 - 0.249)
Typ. All Leads
8° Max, Typ.
All leads
0.053 - 0.069
(1.346 - 1.753)
0.004 - 0.010
(0.102 - 0.254)
Seating
Plane
0.04
(0.102)
All lead tips
0.014
(0.356)
0.016 - 0.050
(0.406 - 1.270)
Typ. All Leads
0.014 - 0.020 Typ.
(0.356 - 0.508)
0.050
(1.270)
Typ
8-Pin Molded Small Outline Package (M8)
Package Number M08A
0.114 - 0.122
(2.90 - 3.10)
8
5
(4.16) Typ (7.72) Typ
0.169 - 0.177
(4.30 - 4.50)
0.246 - 0.256
(6.25 - 6.5)
(1.78) Typ
(0.42) Typ
0.123 - 0.128
(3.13 - 3.30)
(0.65) Typ
1
Land pattern recommendation
4
Pin #1 IDENT
0.0433
Max
(1.1)
0.0256 (0.65)
Typ.
0.0035 - 0.0079
See detail A
0.002 - 0.006
(0.05 - 0.15)
0.0075 - 0.0098
(0.19 - 0.30)
Gage
plane
0°-8°
DETAIL A
Typ. Scale: 40X
0.020 - 0.028
(0.50 - 0.70)
Seating
plane
0.0075 - 0.0098
(0.19 - 0.25)
Notes: Unless otherwise specified
1. Reference JEDEC registration MO153. Variation AA. Dated 7/93
8-Pin Molded Thin Shrink Small Outline Package (MT8)
Package Number MTC08
13
NM24C04/05 Rev. G
www.fairchildsemi.com
0.373 - 0.400
(9.474 - 10.16)
0.090
(2.286)
8
0.092
DIA
(2.337)
7
6
0.250 - 0.005
(6.35 ± 0.127)
+
Pin #1 IDENT
0.032 ± 0.005
(0.813 ± 0.127)
RAD
5
1
1
0.300 - 0.320
(7.62 - 8.128)
7
Pin #1
IDENT
Option 1
0.280 MIN
(7.112)
8
2
3
0.040 Typ.
(1.016)
0.030
MAX
(0.762)
20° ± 1°
4
Option 2
0.145 - 0.200
(3.683 - 5.080)
0.039
(0.991)
0.130 ± 0.005
(3.302 ± 0.127)
95° ± 5°
0.009 - 0.015
(0.229 - 0.381)
+0.040
0.325 -0.015
+1.016
8.255 -0.381
0.125
(3.175)
DIA
NOM
0.125 - 0.140
(3.175 - 3.556)
0.065
(1.651)
90° ± 4°
Typ
0.018 ± 0.003
(0.457 ± 0.076)
0.100 ± 0.010
(2.540 ± 0.254)
0.045 ± 0.015
(1.143 ± 0.381)
0.020
(0.508)
Min
0.060
(1.524)
0.050
(1.270)
Molded Dual-In-Line Package (N)
Package Number N08E
Life Support Policy
Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written
approval of the President of Fairchild Semiconductor Corporation. As used herein:
1. Life support devices or systems are devices or systems which,
(a) are intended for surgical implant into the body, or (b) support
or sustain life, and whose failure to perform, when properly
used in accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a significant
injury to the user.
Fairchild Semiconductor
Americas
Customer Response Center
Tel. 1-888-522-5372
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system,
or to affect its safety or effectiveness.
Fairchild Semiconductor
Europe
Fax:
+44 (0) 1793-856858
Deutsch
Tel:
+49 (0) 8141-6102-0
English
Tel:
+44 (0) 1793-856856
Français
Tel:
+33 (0) 1-6930-3696
Italiano
Tel:
+39 (0) 2-249111-1
Fairchild Semiconductor
Hong Kong
8/F, Room 808, Empire Centre
68 Mody Road, Tsimshatsui East
Kowloon. Hong Kong
Tel; +852-2722-8338
Fax: +852-2722-8383
Fairchild Semiconductor
Japan Ltd.
4F, Natsume Bldg.
2-18-6, Yushima, Bunkyo-ku
Tokyo, 113-0034 Japan
Tel: 81-3-3818-8840
Fax: 81-3-3818-8841
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
14
NM24C04/05 Rev. G
www.fairchildsemi.com
NM24C04/05 – 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
Physical Dimensions inches (millimeters) unless otherwise noted
Similar pages