Vishay NMM0207B01008JBS00 Metal film, cylindrical, fusible resistor Datasheet

NMM0207SI
Vishay Draloric
Metal Film, Cylindrical, Fusible Resistors
FEATURES
• Fusible resistor for constant current designed for
overload protection
• High positive temperature coefficient
• Flame retardant coating
• Defined switch-off behaviour
• Pure tin termination on nickel barrier, plated on fress fit
steel caps
• Compatible with lead (Pb)-free and lead containing
soldering processes
• Lead (Pb)-free and RoHS compliant
STANDARD ELECTRICAL SPECIFICATIONS
POWER RATING1) P70
W
0.35
0.35
MODEL
NMM0207SI
NMM0207SI
TEMPERATURE COEFFICIENT
ppm/K
+ 4500 (± 500)
+ 4500 (± 500)
Note
1. Permissible dissipation depends on the maximum temperature
at the solder point, the component placement density and the
substrate material.
TOLERANCE
%
± 5, ± 10, ± 20
± 10, ± 20
RESISTANCE RANGE
Ω
1R0 - 47R
R10 - R91
E-SERIES
12 - 24
12
• Marking: additional 5th band black; According to IEC 60062; see
also datasheet “surface mount resistor marking” (document
number: 20020)
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
NMM0207SI
Rated Dissipation at 70 °C
Minimum Overload to Fuse
Time to Fuse (max)
Max. applicable Voltage after Fusing
Thermal Resistance2)
Category Temperature Range
Failure Rate
Weight/1000 pcs
W
W
s
V
K/W
°C
10-9/h
g
0.35
1.5
30
85
≤ 220
- 55 to + 125
< 30
71
Note
2. Based on measurements on test board acc. to EN 140400.
PART NUMBER AND PRODUCT DESCRIPTION3)
PART NUMBER4): NMM0207B01008JBP
N
M
M
0
2
0
7
B
0
1
0
0
8
J
B
P
0
0
MODEL/SIZE
SPECIAL CHARACTER
TC
VALUE
TOLERANCE
PACKING5)
SPECIAL
NMM0207
B = SI Fusible
0 = neutral
3 digit value
1 digit multiplier
MULTIPLIER
7 = *10-3
8 = *10-2
9 = *10-1
J=±5%
K = ± 10 %
M = ± 20 %
BP
BS
up to 2 digits
00 = standard
5%
BP
see data sheet
for TC value
PRODUCT DESCRIPTION: NMM0207SI 1R0 5 % BP
NMM0207SI
1R0
MODEL
RESISTANCE VALUE
TOLERANCE
PACKING5)
NMM0207SI
1R0 = 1 Ω
R22 = 0.22 Ω
±5%
± 10 %
± 20 %
BP
BS
Note
3. Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER.
4. The PART NUMBER is shown to facilitate the introduction of a unified part numbering system. Currently, this PART NUMBER is applicable
in the Americas only.
5. Please refer to table PACKING, see below.
www.vishay.com
56
For technical questions contact: [email protected]
Document Number: 20001
Revision: 15-Feb-06
NMM0207SI
Vishay Draloric
Metal Film Cylindrical Resistors
DIMENSIONS
DIMENSIONS [in millimeters]
MODEL
Dmax
d*
L
A max
A min
2.2
D - 0.4
5.8- 0.3
1.2
0.6
NMM0207SI
* d measured in the middle of the resistor
SOLDER PAD DIMENSIONS [in millimeters]
MODEL
REFLOW SOLDERING WAVE SOLDERING
NMM0207SI
a
b
l
a
b
l
1.8
2.5
2.9
2.4
2.5
2.8
PACKING
BLISTER TAPE ON REEL
ACC. IEC 60286-3
MODEL
NMM0207SI
DIAMETER
PIECES/REEL
CODE
180 mm/7"
330 mm/13"
1500
7500
BP
BS
120
Fusing Time in s
Power Rating P in %
Further
information
about
PACKING,
see
also
datasheet
“surface
mount
resistor
packing”
(document
number:
20014).
100
80
60
20
10
7
5
4
3
40
20
0
- 55
50
40
30
2
- 25
0
25
50
Derating
70
75
100
125
Ambient Temp in °C
1
1
2
3
4
Fusing Performance
5
6 7 8 9 10
Power in W
PERFORMANCE
TEST
CONDITIONS OF TEST
Endurance Test at 70 °C
IEC 60115-1, 4.25.1
1000 hours at 70 °C, 1.5 hours "ON", 0.5 hours "OFF"
≤2%
Endurance at UCT
IEC 60115-1, 4.25.3
1000 hours at 125 °C without load
≤2%
Overload Test
IEC 60115-1, 4.13
Short time overload for 2 seconds
≤2%
Thermal Shock
IEC 60115-1, 4.19 and IEC 60068-2-14
Rapid change between upper and lower category temperature,
5 cycles
≤2%
Damp Heat Steady State
IEC 60115-1, 4.24 and IEC 60068-2-78
56 days at 40 °C and 93 % relative humidity
≤2%
Resistance to Soldering Heat
IEC 60115-1, 4.18 and IEC 60068-2-58
10 seconds at 260 °C solder bath temperature
≤1%
Document Number: 20001
Revision: 15-Feb-06
For technical questions contact: [email protected]
REQUIREMENTS
www.vishay.com
57
NMM0207SI
Vishay Draloric
Metal Film Cylindrical, Fusible Resistors
SOLDERING INFORMATION
• For reflow soldering only
• Board has to be thoroughly cleaned after soldering. All flux materials must be completely removed
APPLICABLE SPECIFICATION
• EN 60115-1
www.vishay.com
58
For technical questions contact: [email protected]
Document Number: 20001
Revision: 15-Feb-06
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
Similar pages