CANDD NNL10-7 Non-isolated dc/dc converter Datasheet

NNL10 SERIES
Non-Isolated DC/DC Converters
SELECTION GUIDE1
Nominal
Input
Voltage
Output
Voltage
Output
Current
Min
Load
Order Code
FEATURES
■ Industry Standard Footprint
■ Short Circuit Protection
■ High Efficiency
■ Under Voltage Lock Out
■ Optional DC OK Signal
■ Options available without Trim and
Remote Sense Functionality
DESCRIPTION
The NNL10 series is part of a range of nonisolated, cost effective DC/DC converters
offering high precision output voltages from a
nominal 3.0–5.5 or 10.0–14.0 intermediate
bus where isolation is not required. Available
in both SMD and SIP mechanical formats.
Full
Load
Min
V
V
A
A
W
%
4.0
0.9
0
10.0
9.0
79.7
NNL10-2
4.0
1.0
0
10.0
10.0
81.8
NNL10-3
4.0
1.2
0
10.0
12.0
84.3
NNL10-4
4.0
1.5
0
10.0
15.0
86.5
NNL10-5
4.0
1.8
0
10.0
18.0
88.2
NNL10-6
4.0
2.0
0
10.0
20.0
89.2
NNL10-7
4.0
2.5
0
10.0
25.0
91.2
NNL10-8
4.0
3.3
0
10.0
33.0
92.1
NNL10-9
4.0
0.9
0
10.0
9.0
79.7
NNL10-10
4.0
1.0
0
10.0
10.0
81.8
NNL10-11
4.0
1.2
0
10.0
12.0
84.3
NNL10-12
4.0
1.5
0
10.0
15.0
86.5
NNL10-13
4.0
1.8
0
10.0
18.0
88.2
NNL10-14
4.0
2.0
0
10.0
20.0
89.2
NNL10-15
4.0
2.5
0
10.0
25.0
91.2
NNL10-16
4.0
3.3
0
10.0
33.0
92.1
With DCOK
■ SMD Construction
Nominal
Efficiency
NNL10-1
■ Output Voltage Trimming
■ Operating Temperature Range
–40°C to 85°C
MAX
Output
Power
INPUT CHARACTERISTICS1
Parameter
Voltage Range
Conditions
MIN
VNOM = 4.0VDC VOUT < 2.75V
VNOM = 4.0VDC VOUT > 3.0V
Turn On Threshold VNOM = 4.0VDC
Turn Off Threshold VNOM = 4.0VDC
3.0
4.0
Under Voltage
Lock Out
Reflected Ripple
Current
Input No Load VIN = 5.5V VOUT = 0.9V
Current
VIN = 5.5V VOUT = 3.3V
Input Standby
VIN = 5.5V Module Disabled
Current
TYP
MAX
Units
5.5
5.5
V
2.8
2.7
V
30
mA p-p
100
140
mA
1.5
mA
OUTPUT CHARACTERISTICS1
Parameter
Conditions
Rated Current
TA = –40°C to 85°C
(see thermal performance characteristics)
Voltage Set
Point Accuracy
Line Regulation
Load Regulation
Ripple & Noise
Voltage Trim
Remote Sense
Transient
Response
External Load
Capaitance
MIN
Low line to high line
0% load to 100% load
BW = DC to 20MHz
TYP
Units
10.0
A
1.0
2.0
%
0.5
1.0
0.55
50
+10
0.5
100
70
%
%
mVp-p
%VOUT
V
mV
µs
10,000
µF
25
-10
IOUT = 5.0A–10.0A–5.0A, Peak Deviation
COUT = 1µF//10µF
Settling Time
MAX
1 Specifications typical at TA =25°C, nominal input voltage and rated output current unless otherwise specified.
www.cdpoweronline.com
Other customer specified options are available on request. Standard parts are supplied with Remote Sense and
Voltage Trim functions. Please contact your sales representative or C&D Technologies account manager for
further details.
1
NNL10 SERIES
Non-Isolated DC/DC Converters
GENERAL CHARACTERISTICS1
Parameter
ABSOLUTE MAXIMUM RATINGS
Conditions
Switching Frequency
Start Delay
MIN
TYP
MAX
300
4.0
From power on/remote off
0
Module On (or pin unconnected)
Remote On/Off
kHz
ms
V
µA
V
µA
kHrs
0.3
100
2.6
Module Off
-500
MTTF
Short circuit protection
Remote Sense
DC OK
Units
TBA
Remote ON/OFF
Trim
Input Voltage VIN
Minimum load
Continuous
VOUT±0.5VDC
-0.2Vdc to +17VDC
20mA
-0.2VDC to +17VDC
-0.3VDC to VOUT
6.5VDC
0%
ENVIRONMENTAL1
Parameter
Conditions
MIN
See thermal performance
characteristics
Substrate temperature
Operation
Over Temperature Protection
Storage
TYP
–40
MAX
Units
85
°C
125
°C
°C
115
–55
OUTPUT VOLTAGE TRIMMING
The trimming input on the NNL10 allows output voltage adjustment by +/-10% of nominal output voltage by
connection of a resistor or by application of a voltage to the Trim pin.
RINTERNAL VALUES
FIG.1
VOUT SET
RINTERNAL
(V)
0.9
1.0
1.2
1.5
1.8
2.0
2.5
3.3
(kOhm)
5.1
30.1
59.0
100.0
100.0
100.0
78.7
59.0
FIG.2
VIN
VOUT
NNL10
VOUT
VIN
RTRIM
TRIM
NNL10
RTRIM
TRIM
GND
GND
To increase the output voltage, an external resistor (Fig. 1) or voltage
source should be connected between the Trim pin and GND pin.
RTRIM–UP =
24.080
∆VOUT
– RINTERNAL KΩ
VTRIM–UP = 0.8 –
∆VOUT x RINTERNAL
30.100
∆Vout is the required change in output voltage in V
To decrease the output voltage, an external resistor (Fig. 2) or voltage source should be connected between
the Trim pin and the VOUT pin.
RTRIM–DOWN =
VOUT –0.8
–1 x 30.100 – RINTERNAL KΩ
∆VOUT
VTRIM–DOWN = 0.8 + ∆VOUT x
RINTERNAL
30.100
The trim pin should be left disconnected if not used.
2
NNL10 SERIES
Non-Isolated DC/DC Converters
REMOTE SENSE
The remote sense function compensates for voltage drops from the
output of the NNL10 to the load point by regulating the output voltage at the load point. The voltage drop must not exceed 0.5V,
although Trim and remote sense functions can be used in combination with each other, the maximum voltage increase is 0.5V.
FIG.3
VOUT
VIN
NNL10
SENSE
GND
LOAD
OUTPUT SEQUENCING
FIG.4
To simplify output sequencing, the
NNL10 series offers an optional single
wire interconnection that performs this
function. Using this connection, up to
four devices can be 'daisy chained'
together, with the 'DC OK' signal from
one converter signifying that the next
converter can be enabled. A
capacitor, simply connected to the
daisy chain link, provides a settable
delay in the sequence of the
converters starting.
Typical capacitor values and
corresponding delays are shown in
the table below.
Figure 4 shows a typical sequencing
configuration, along with the voltage
outputs that it produces. As well as
reducing component count, making
use of the 'built-in' sequencing
capability means that only a single
PCB track is required for a full
sequencing solution.
VIN
3.0VDC
5.5VDC
Capacitor Value
0.22µF
0.22µF
When increasing the output voltage the maximum output power of
the NNL10 must not exceed the maximum output figures stated in
the selection guide.
VOUT 1
Bus Voltage
VOUT 1
VIN
DC OK
TPRESET
VOUT 2
ON/OFF
VOUT 2
VIN
VOUT 3
ON/OFF
VOUT 3
VIN
DC OK
TPRESET + TCAP
VOUT 4
ON/OFF
VIN
Delay
1.8mS
0.6mS
VOUT 4
Capacitor
3
NNL10 SERIES
Non-Isolated DC/DC Converters
EFFICIENCY v LOAD GRAPHS (NNL10 VNOM = 4.0VDC)
VOUT = 0.9V
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.3V
4
NNL10 SERIES
Non-Isolated DC/DC Converters
THERMAL DERATING GRAPHS (NNL10 VNOM = 4.0VDC)
VOUT = 0.9V
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.0V
VOUT = 2.5V
VOUT = 3.3V
5
NNL10 SERIES
Non-Isolated DC/DC Converters
TYPICAL CHARACTERISTICS
OUTPUT RIPPLE & NOISE
VIN = 4.75VDC
VOUT = 3.3VDC
IOUT = 10.0A
START-UP FROM APPLICATION OF VIN
VIN = 4.0VDC
VOUT = 0.9VDC
IOUT = 10.0A
START-UP USING REMOTE ON/OFF
Response when remote on/off driven from an open collector output.
TRANSIENT RESPONSE
VIN = 4.0VDC
VOUT = 3.3VDC
IOUT Change = 50-100%
VIN = 4.0VDC
VOUT = 3.3VDC
IOUT Change = 100-50%
6
NNL10 SERIES
Non-Isolated DC/DC Converters
PIN CONNECTIONS
Pin Number
1
2
3
4
5
6
7
ON/OFF
VIN
DC OK*
GND
VOUT
TRIM
SENSE
* Pin 6 (DC OK) is an optional feature which allows multiple NNL10 DC/DC Converters to have sequenced outputs
when used in conjunction with the Remote ON/OFF pin (see application note for further information).
MECHANICAL DIMENSIONS
SMD Package Style Bottom View
0.075 (1.91)
0.112 (2.84)
0.048 (1.22)
0.062
(1.58)
2
1
0.405
(10.29)
0.062
(1.57)
0.530
(13.46)
7
0.297
(7.54)
6
0.19
(4.83)
5
0.19
(4.83)
4
0.19
(4.83)
3
0.19
(4.83) 0.12
(3.04)
0.326
(8.28)
MAX
1.3 (33.0)
Unless otherwise stated all dimensions in inches(mm) ±0.01(0.25).
Weight: 5.7g
PACKAGING
Tray Dimensions (top view)
12.40(315.00)
1.614(41.0)†
1.102†
(28.0)
5.354
(136.0)
0.709(18.0)
Pick up location (top view)
0.265(6.73)
Tray quantity: 28
†
+0.020(0.5)
-- 0.00(0.0)
0.476(12.08)
Unless otherwise stated all dimensions in inches(mm) ± 0.014(0.35).
C&D Technologies Inc. reserve the right to alter or improve the specification,
internal design or manufacturing process at any time, without notice. Please
check with your supplier or visit our web site to ensure that you have the
current and complete specification for your product before use.
© C&D Technologies Inc. 2004
NDC NNL10.2
No part of this publication may be copied, transmitted or stored in a
retrieval system or reproduced in any way including, but not limited to,
photography, photocopy, magnetic or other recording means, without prior
written permission from C&D Technologies Inc.
C&D Technologies (NCL) Ltd
Tanners Drive, Blakelands North
Milton Keynes MK14 5BU, England
Tel: +44 (0)1908 615232
Fax: +44 (0)1908 617545
email: [email protected]
C&D Technologies Inc.
3400 E Britannia Drive, Tucson,
Arizona 85706, USA
Tel: +1 (800) 547-2537
Fax: +1 (520) 741-4598
email: [email protected]
www.cdpoweronline.com
Instructions for use are available from: www.cdpoweronline.com
7
Similar pages