CANDD NPH10S Isolated 10w single output dc/dc converter Datasheet

NPH10S SERIES
Isolated 10W Single Output DC-DC Converters
SELECTION GUIDE
Nominal
Input Voltage
Output
Voltage
Output
Current
Current
Limit2 (Typ)
(V)
24
24
24
24
48
48
48
48
(V)
3.4
5.1
12.1
15.1
3.4
5.1
12.1
15.1
(A)
2.94
1.96
0.83
0.67
2.94
1.96
0.83
0.67
(A)
4.5
3.0
1.2
1.1
4.1
2.8
1.2
1.0
Order Code1
NPH10S2403i
NPH10S2405i
NPH10S2412i
NPH10S2415i
NPH10S4803i
NPH10S4805i
NPH10S4812i
NPH10S4815i
FEATURES
INPUT CHARACTERISTICS
■ High Efficiency to 86%
Parameter
Conditions
■ Power Density up to 1.5kW/L
(24W/in3 )
Voltage Range
Continuous operation, 24V input types
Continuous operation, 48V input types3
■ 1.5kV Input to Output Isolation
OUTPUT CHARACTERISTICS
■ Industry Standard Pinout
Parameter
Conditions
■ Surge Rating to 12W
Voltage Set
Point Error
50% load after 30 mins at nominal
supply voltage
Case temperature –40°C to 110°C
Load 0% - 100%
Input specified range
■ Non Latching Current Limit
■ Fixed Frequency
■ Versatile Control Options
■ Continuous Rating to 10W at 72°C
Without Heatsink
■ Operation to Zero Load
■ Protected Against Load Faults
■ Internal Over Temperature Protection
■ Uses No Electrolytic Capacitors
■ UL 94V-0 Package Materials
DESCRIPTION
The NPH10S series of DC-DC Converters
combines ease of application with versatility.
The pin pattern is based on the popular
industry standard, but two additional pins
may optionally be fitted to provide a variety
of features not commonly found on units of
this type. High efficiency enables full rating
to be achieved in a small package without
heatsinking. Thermally protected against
sustained overload. The copper case
achieves efficient heat transfer and screening.
The product range has been recognised by
Underwriters Laboratory (UL) to UL 1950 for
operational insulation, file number E179522
applies.
Overall
Voltage Error
Temperature Coefficient
of Output Voltage
(slope)
Deviation of
Output Voltage
Line Regulation
Load Regulation
Ripple
(%)
79
83
86
86
80
83
86
87
(µF)
470
470
100
47
470
470
56
22
MIN
NOM
MAX
Units
18
36
24
48
36
75
V
V
MIN
TYP
MAX
Units
0.5
%
1
2.5
%
Over any 10°C span within the
specified temperature range
50
250
ppm°C
Specified over temperature MIN-MAX
0.5
1
%
Operating voltage range, 50% load
0% - 100% rated load4
rms
0.05
0.1
0.5
%
%
mV
MAX
Units
70
CONTROL CHARACTERISTICS
Parameter
Conditions
Voltage Trimming
Range
Remote Switch Input5
At rated load,
Trim control at either output
Not operating
(voltage relative
to input negative)
Start Delay
Synchronisation
Switching Frequency
5
MIN
Operating, open circuit voltage
Time from application of valid input
voltage to output being in specification
Specified drive signal
TYP
±10
%
-15
0
1.5
9
10
11
25
320
330
350
V
mS
440
395
kHz
kHz
ABSOLUTE MAXIMUM RATINGS
Input voltage, 24V input types
Input voltage, 48V input types
Output Voltage
Output trim control
Synchronisation/shutdown control
–0.5V to 40V6
–0.5V to 80V6
–0.3V to controlled output voltage (operating or non-operating)
–1V to +30V
±15V relative to input return
ISOLATION CHARACTERISTICS
Parameter
Conditions
Isolation Voltage
Resistance
Flash tested for 1 second
Viso=500VDC
3.3V and 5V output
12V and 15V output
Capacitance
www.cdpoweronline.com
Max Load
Efficiency Capacitance
MIN
TYP
1500
1
MAX
Units
VDC
GΩ
50
90
pF
1 If optional pins ADJ and SS are required (as indicated in the pin connections diagram) prefix the ending “i” with
an E when ordering, e.g. NPH10S4803Ei.
2 Current is quoted when output is 95% of regulated voltage.
3 For applications requiring UL1950 recognition, input voltage must not exceed 60VDC.
4 A minimum load of 10% of rating is recommended for typical applications ; see application notes.
5 Optional - Where fitted.
6 Absolute maximum value for 30 seconds. Prolonged operation may damage the product.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.
NPH10S SERIES
Isolated 10W Single Output DC-DC Converters
ENVIRONMENTAL
THERMAL PERFORMANCE
Conditions
MIN
Case Temperature
Storage
Relative Humidity
Thermal Protection
Full load
Absolute MAX internal temperature
Non condensing 85°C
Operates at case temperature
–40
–40
TYP
MAX
Units
110
125
85
°C
°C
%
°C
110
15
2415
Output Power (W)
Parameter
THERMAL CHARACTERISTICS
MAX power rating with case temperature maintained by external means
(eg forced air cooling)
NPH10S2403
NPH10S2405
NPH10S2412
NPH10S2415
NPH10S4803
NPH10S4805
NPH10S4812
NPH10S4815
100°C
10
10
10
12
10
10
12
12
105°C
7.0
8.2
9.5
9.5
7.0
4.7
8.0
7.5
110°C
2.3
3
4
4
1
1
0
0
2403
-20
0
20
40
60
W
W
10
4803
5
-20
0
20
40
4812
60
1.26
(32.00)
0.09 (2.34)
BOTTOM VIEW
0.2(5.08)
+V OUT
SS
+VIN
-VIN
0.39 (9.96)
0.80 (20.32)
ADJ
0V
0.2 (5.08)
1.78 (4.50)
0.15 (3.70)
0.39 (10.00)
0.04 (1.04)
Ø
0.04 (0.90)
C&D Technologies (NCL) Limited reserve the right to alter or improve the
specification, internal design or manufacturing process at any time, without
notice. Please check with your supplier or visit our web site to ensure that
you have the current and complete specification for your product before use.
For information and instructions on use, please consult the NPH SERIES
APPLICATION NOTES.
© C&D Technologies (NCL) Limited 2003
0.23
(5.84)
NDC NPH10S.6
No part of this publication may be copied, transmitted or stored in a
retrieval system or reproduced in any way including, but not limited to,
photography, photocopy, magnetic or other recording means, without prior
written permission from C&D Technologies (NCL) Limited.
Instructions for use are available from www.cdpoweronline.com
0.8
20.32
Weight: 22g
All dimensions in Inches (mm) ± 0.01 (0.25)
All pins on a 0.10 (2.54) pitch and within ± 0.01 (0.25) of true position
* Optional pins
Case connected internally to 0V pin
C&D Technologies (NCL) Ltd
Tanners Drive, Blakelands North
Milton Keynes MK14 5BU, England
Tel: +44 (0)1908 615232
Fax: +44 (0)1908 617545
email: [email protected]
www.cdpoweronline.com
80
Ambient Temperature (°C)
MECHANICAL DIMENSIONS
0.98
25.00
100 120
4815
4805
0
-40
0.2 (5.08)
80
Ambient Temperature (°C)
15
Units
Output Power (W)
Part Number
2412
5
0
-40
Case Temperature
2405
10
C&D Technologies Inc.
3400 E Britannia Drive, Tucson,
Arizona 85706, USA
Tel: +1 (800) 547-2537
Fax: +1 (520) 741-4598
email: [email protected]
100 120
Similar pages