Microdc NTE0503XMC 1w, fixedinput, isolated singleoutputsmd dc-dcconverter Datasheet

NTE-X Series
D DC-DC CONVERTER
1W, FIXED INPUT, ISOLATED SINGLE OUTPUT SM
SMD
SELECTION GUIDE
Input
Output
Nominal
Current
(mA)
Rated Load
NTE0303XMC
3.3
NTE0305XMC
NTE0309XMC
◆Short Circuit Protection(automatic recovery)
◆I/O isolation voltage 1000VDC
Order code
Voltage(VDC)
Isolation
Capacitance
MTTF1
(VDC)
Current
(mA)
(%.Typ.)
pF
KHrs
410
3.3
303
81
29
5348
3.3
390
5
200
83
30
3847
3.3
400
9
111
74
34
3134
NTE0312XMC
3.3
400
12
83
76
40
3473
NTE0315XMC
3.3
400
15
66
81
42
2473
NTE0503XMC
5
270
3.3
303
85
31
5515
NTE0505XMC
5
294
5
200
83
33
6857
◆High efficiency up to 78%
NTE0505NXMC
5
260
5
200
86
42
3933
◆Toroidal magnetics
NTE0506XMC
5
278
6
167
83
43
6677
NTE0509XMC
5
267
9
111
85
38
5501
NTE0512XMC
5
260
12
83
74
44
3957
NTE0515XMC
5
256
15
66
78
43
2747
◆Lead frame technology
NTE1205XMC
12
124
5
200
80
50
4683
◆Multi-layer ceramic capacitors
NTE1209XMC
12
114
9
111
80
72
4008
◆Custom solutions available
NTE1212XMC
12
113
12
83
85
89
3121
NTE1215XMC
12
111
15
66
81
100
2316
FEATURES
◆Footprint over pins 1.37cm2
◆Operating Temperature: -40℃~﹢85℃
◆Small SMD package with footprint
◆Power density 1.8W/cm3
Voltage
Efficiency
1. Calculated using MIL-HDBK-217FN2 with nominal input voltage at full load.
All specifications typical at TA=25℃, nominal input voltage and rated output current unless otherwise specified.
MODEL SELECTION
NTE①05②05③XMC④
①Product Series
③Output Voltage
②Input Voltage
④Fixed Input&SMD Package
Input Characteristics
Parameter
Voltage range
APPLICATIONS
The NTE-X series are miniature,1W DC/DC
converters with high isolation in a SMD
package. With a new package design these
converters
are
qualified
for
the
higher
temperatures requested by lead-free reflow
Conditions
Min.
Typ.
Max.
Units
Continuous operation, 3.3V input
2.97
3.3
3.63
VDC
Continuous operation, 5V input
4.5
5
5.5
VDC
Continuous operation, 12V input
10.8
12
13.2
VDC
30
47
mA p-p
Typ.
Max.
Units
Start up time
Isolation Characteristics
Parameter
Conditions
Min.
Isolation voltage
Flash tested for 1 second
1000
VDC
Resistance
Viso= 1000VDC
10
GΩ
solder processes. With the small footprint,
these converters are the ideal solution for
General Characteristics
board level power distribution,mainly for
Parameter
Conditions
applications in the industrial and telecom field.
Switching frequency
All output types
Min.
Typ.
Max.
Units
110
kHz
For automated SMD production lines the
devices can be supplied in standard tape and
reel package.
Absolute Maximum Ratings
Parameter
Conditions
Lead temperature 1.5mm from case for 10 seconds
300℃
Internal power dissipation
600mW
Input voltage V , NTE03 types
5.5V
Input voltage Vin, NTE05 types
7V
Input voltage Vin, NTE12 types
15V
MICRODC RESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 6
NTE-X Series
Output Specifications
Parameter
Conditions
Rated Power
TA=-40°C to 85°C
Voltage Set Point
See tolerance envelope
Line regulation
Min.
Typ.
Max.
Units
1.0
W
High VIN to low VIN
1.0
1.2
%%
10% load to rated load, 0303XMC& 0503XMC
10
14
%
10% load to rated load, 0505XMC&1205XMC
12.8
15
%
10% load to rated load, 0506XMC
9.2
10
%
10% load to rated load, 0509XMC& 1209XMC
8.3
9.0
%
10% load to rated load, 0512XMC& 1212XMC
6.8
7.5
%
10% load to rated load, 0515XMC& 1215XMC
6.3
7.0
%
BW=DC to 20MHz, 3.3V output types, 0305XMC & 0505XMC
40
60
mV p-p
Load regulation1
BW=DC to 20MHz, 3.3V output types,0505XMC & 1205XMC
62
85
mV p-p
BW=DC to 20MHz, 0506XMC
103
170
mV p-p
BW=DC to 20MHz, 0509XMC& 1209XMC
49
75
mV p-p
BW=DC to 20MHz, 0512XMC& 1212XMC
39
65
mV p-p
BW=DC to 20MHz, 0515XMC& 1215XMC
38
76
mV p-p
Typ.
Ripple&Noise
Note:1、12V input types have typically 3% less load regulation change.
Temperature Characteristics
Parameter
Conditions
Min.
Max.
Units
Specification
All output types
-40
85
℃
-55
125
℃
Storage
Case temperature
rise above ambient
Cooling
0305, 0309, 0315
25
℃
0303, 0312, 0503, 0505, 0509, 0512, 0515
30
℃
0505, 1205
43
℃
1209, 1212, 1215
40
℃
Free air convection
Technical notes
ISOLATION VOLTAGE
‘Hi Pot Test’
、“Flash Tested’
、
”Withstand Voltage“、
‘Proof Voltage”
、
“Dielectric Withstand Voltage'&'Isolation Test Voltage”are all terms that relate to the same thing, a test voltage, applied for a speciffi
ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Professional Power Module NTE-X series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speciffic agency approvals, such as the NTE-X series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage
represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts
offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a
barrier between these circuits and any user-accessible circuitry according to safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment.
The NTE-X series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated
test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high
applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be
reduced by 20% from speciffied test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
Temperature derating graph
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 6
NTE-X Series
Application Notes
Minimum load
The minimum load to meet data sheet speciffication is 10% of the full rated load across the speciffied input voltage range. Lower than 10% minimum loading will result in an
increase in output voltage, which may rise to typically double the speciffied output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product series will start
into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Start-up time
Start-up time
μs
μs
NTE0303XMC
437
NTE0506XMC
7200
NTE0305XMC
1359
NTE0509XMC
3146
NTE0309XMC
3435
NTE0512XMC
4960
NTE0312XMC
6590
NTE0515XMC
7740
NTE0315XMC
7625
NTE1205XMC
895
NTE0503XMC
533
NTE1209XMC
2150
NTE0505XMC
1368
NTE1212XMC
3640
NTE0505NXMC
721
NTE1215XMC
7180
Ripple & Noise Characterization Method
Ripple and noise measurements are performed with the following test configuration.
C1
1μF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
C2
than 100mΩ at 100 kHz
C3
100nF multilayer ceramic capacitor, general purpose
R1
450Ω resistor, carbon fi lm, ±1% tolerance
R2
50Ω BNC termination
T1
3T of the coax cable through a ferrite toroid
RLOAD
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Measured values are multiplied by 10 to obtain the specified values.
Differential Mode Noise Test Schematic
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 3 of 6
NTE-X Series
Application Notes
Output Ripple Reduction
By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max.
Component selection
Capacitor: It is required that the ESR (Equivalent Series Resistance) should be as low as possible, ceramic types are recommended.
The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter.
Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be
such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz.
Inductor
Capacitor
L,μH
SMD
Through Hole
C,μF
NTE0303XMC
10
82103C
11R103C
4.7
NTE0305XMC
47
82473C
11R103C
4.7
NTE0309XMC
22
82223C
11R223C
2.2
NTE0312XMC
10
82103C
11R103C
1
NTE0315XMC
47
82473C
11R473C
1
NTE0503XMC
10
82103C
11R103C
4.7
NTE0505XMC
47
82473C
11R473C
4.7
NTE0505NXMC
47
82473C
11R473C
4.7
NTE0506XMC
10
82103C
11R103C
4.7
NTE0509XMC
22
82223C
11R223C
2.2
NTE0512XMC
47
82473C
11R473C
1
NTE0515XMC
47
82473C
11R473C
1
NTE1205XMC
47
82473C
11R473C
4.7
NTE1209XMC
22
82223C
11R223C
2.2
NTE1212XMC
47
82473C
11R473C
1
NTE1215XMC
47
82473C
11R473C
1
Tolerance Envelopes
The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to
changes in output loading.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 4 of 6
NTE-X Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
SOLDER PAD DIMENSION
Dimensions in [mm], () = Inch
Pin pitch tolerances: ±0.13 (±0.005)
Other tolerances: ±0.25 (±0.01)
PRODUCT ID DESCRIPTION
Note:
Unit:mm[inch]
Pin section tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
Weight: 1.21g
FOOTPRINT DETAILS
Pin
Single
1
-Vin
3
+Vin
5
NA
7
-Vout
8
+Vout
10
NA
12
NA
14
NA
TUBE OUTLINE DIMENSIONS
NA - Not available for electrical connection.
Specifications can be changed any time without notice.
No parallel connection or plug and play.
Note:
Unless otherwise stated all dimensions in mm±0.5 (inches ±0.02).
Tube length : 475±2.0 (18.70±0.07).
Tube Quantity :35
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2. Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise
specified.
4. In this data sheet, all the test methods of indications are based on corporate standards.
5. Only typical models listed, other models may be different, please contact our technical person for more details.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 5 of 6
NTE-X Series
Tape & Reel Specifications
Reel Packaging Details
Product Orientation
Pin 1, located nearest to carrier drive sprocket.
Reel Quantity : 500
Reel Outline Dimensions
Tape Outline Dimensions
RoHS COMPLIANT INFORMATION
Microdc Professional Power Module,Inc.
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C
Tel:0086-20-86000646 E-mail:[email protected]
for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte
.microdc.
cn
Website: www
www.microdc.
.microdc.c
Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are
Microdc Professional Power module,Inc.makes no representation that
backward compatible with Sn/Pb soldering systems.
the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or
REACH COMPLIANT INFORMATION
future patent rights. Specifications are subject to change without notice.
This series has proven that this product does not contain harmful chemicals, it also has harmful chemical
©2010
Microdc Professional Power Module, Inc. Guangzhou
substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 6 of 6
Similar pages