Sample & Buy Product Folder Support & Community Tools & Software Technical Documents Reference Design OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 OPAx171 36-V, Single-Supply, SOT553, General-Purpose Operational Amplifiers 1 Features 3 Description • • • • • • • • • • • • The OPA171, OPA2171, and OPA4171 (OPAx171) are a family of 36-V, single-supply, low-noise operational amplifiers with the ability to operate on supplies ranging from 2.7 V (±1.35 V) to 36 V (±18 V). These devices are available in micro-packages and offer low offset, drift, and bandwidth with low quiescent current. The single, dual, and quad versions all have identical specifications for maximum design flexibility. 1 • Supply Range: 2.7 to 36 V, ±1.35 V to ±18 V Low Noise: 14 nV/√Hz Low Offset Drift: ±0.3 µV/°C (Typical) RFI Filtered Inputs Input Range Includes the Negative Supply Input Range Operates to Positive Supply Rail-to-Rail Output Gain Bandwidth: 3 MHz Low Quiescent Current: 475 µA per Amplifier High Common-Mode Rejection: 120 dB (Typical) Low-Input Bias Current: 8 pA Industry-Standard Packages: – 8-Pin SOIC – 8-Pin MSOP – 14-Pin TSSOP microPackages: – Single in SOT553 – Dual in VSSOP-8 2 Applications • • • • • • • • • Unlike most operational amplifiers, which are specified at only one supply voltage, the OPAx171 family is specified from 2.7 to 36 V. Input signals beyond the supply rails do not cause phase reversal. The OPAx171 family is stable with capacitive loads up to 300 pF. The input can operate 100 mV below the negative rail and within 2 V of the top rail during normal operation. These devices can operate with full rail-to-rail input 100 mV beyond the top rail, but with reduced performance within 2 V of the top rail. The OPAx171 series of operational amplifiers are specified from –40°C to 125°C. Device Information(1) PART NUMBER Tracking Amplifier in Power Modules Merchant Power Supplies Transducer Amplifiers Bridge Amplifiers Temperature Measurements Strain Gauge Amplifiers Precision Integrators Battery-Powered Instruments Test Equipment SPACE Offset Voltage vs Common-Mode Voltage 1000 BODY SIZE (NOM) SOT23 (5) 1.60 mm × 2.90 mm OPA2171 SOIC (8) 3.90 mm × 4.90 mm TSSOP (14) 4.40 mm × 5.00 mm SOIC (14) 3.90 mm × 8.65 mm OPA4171 (1) For all available packages, see the orderable addendum at the end of the data sheet. Offset Voltage vs Power Supply 10 Typical Units Shown 800 PACKAGE OPA171 350 600 VSUPPLY = ±1.35V to ±18V 10 Typical Units Shown 250 150 200 VOS (mV) VOS (mV) 400 0 -200 50 -50 -400 -150 -600 -800 -250 VCM = -18.1V -1000 -20 -15 -10 -5 0 VCM (V) 5 10 15 20 -350 0 2 4 6 8 10 12 14 16 18 20 VSUPPLY (V) 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 5 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 5 5 5 6 6 6 7 9 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information: OPA171 .................................. Thermal Information: OPA2171 ................................ Thermal Information: OPA4171 ................................ Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 16 7.1 Overview ................................................................. 16 7.2 Functional Block Diagram ....................................... 16 7.3 Feature Description................................................. 16 7.4 Device Functional Modes........................................ 18 8 Application and Implementation ........................ 19 8.1 Application Information............................................ 19 8.2 Typical Application ................................................. 20 9 Power Supply Recommendations...................... 23 10 Layout................................................................... 23 10.1 Layout Guidelines ................................................ 23 10.2 Layout Example .................................................... 23 11 Device and Documentation Support ................. 24 11.1 11.2 11.3 11.4 11.5 Related Links ........................................................ Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 24 24 24 24 24 12 Mechanical, Packaging, and Orderable Information ........................................................... 24 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision D (September 2012) to Revision E Page • Changed device title (removed "Value Line Series").............................................................................................................. 1 • Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................. 1 Changes from Revision C (June 2011) to Revision D • Page Added "Value Line Series" to title........................................................................................................................................... 1 Changes from Revision B (November 2010) to Revision C Page • Added MSOP-8 package to device graphic ........................................................................................................................... 1 • Added MSOP-8 package to Features bullets ......................................................................................................................... 1 • Added MSOP-8 package to Product Family table.................................................................................................................. 1 • Updated pinout configurations for OPA2171 and OPA4171 .................................................................................................. 3 • Updated format of thermal information tables ........................................................................................................................ 6 • Added MSOP-8 package to OPA2171 Thermal Information table ......................................................................................... 6 • Added new row for Voltage Output Swing from Rail parameter to Output subsection of Electrical Characteristics.............. 7 • Changed Voltage Output Swing from Rail parameter to over temperature in Output subsection of Electrical Characteristics ........................................................................................................................................................................ 7 • Changed Figure 9................................................................................................................................................................. 10 Changes from Revision A (November, 2010) to Revision B Page • Changed input offset voltage specification ............................................................................................................................. 7 • Changed input offset voltage, over temperature specification ............................................................................................... 7 • Changed quiescent current per amplifier, over temperature specification ............................................................................. 8 2 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 5 Pin Configuration and Functions DRL Package: OPA171 SOT-553 Top View IN+ 1 V- 2 IN- 3 5 4 D, DCU, and DGK Packages: OPA2171 SO-8, VSSOP-8, and MSOP-8 Top View V+ OUT A 1 8 V+ -IN A 2 7 OUT B +IN A 3 6 -IN B V- 4 5 +IN B OUT DBV Package: OPA171 SOT23-5 Top View OUT 1 V- 2 +IN 3 D and PW Packages: OPA4171 SO-14 and TSSOP-14 Top View 5 V+ 4 -IN OUT A 1 14 OUT D -IN A 2 13 -IN D +IN A 3 12 +IN D V+ 4 11 V- +IN B 5 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C D PACKAGE: OPA171 SO-8 Top View 1 8 NC -IN 2 7 V+ +IN 3 6 OUT V- 4 5 NC(1) NC (1) (1) (1) No internal connection. Pin Functions: OPA171 PIN NAME I/O DESCRIPTION DRL DBV D +IN 1 3 3 I Noninverting input –IN 3 4 2 I Inverting input OUT 4 1 6 O Output V+ 5 5 7 — Positive (highest) supply V– 2 2 4 — Negative (lowest) supply NC — — 1, 5, 8 — No internal connection (can be left floating) Pin Functions: OPA2171 PIN I/O DESCRIPTION NAME DCU DGK D +IN A 3 3 3 I Noninverting input +IN B 5 5 5 I Noinverting input –IN A 2 2 2 I Inverting input –IN B 6 6 6 O Inverting input OUT A 1 1 1 O Output OUT B 7 7 7 — Output Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 3 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com Pin Functions: OPA2171 (continued) PIN NAME I/O DESCRIPTION DCU DGK D V+ 8 8 8 — Positive (highest) supply V– 4 4 4 — Negative (lowest) supply Pin Functions: OPA4171 PIN I/O DESCRIPTION NAME DCU DGK +IN A 3 3 I Noninverting input +IN B 5 5 I Noninverting input +IN C 10 10 I Noninverting input +IN D 12 12 I Noninverting input –IN A 2 2 I Inverting input –IN B 6 6 I Inverting input –IN C 9 9 I Inverting input –IN D 13 13 I Inverting input OUT A 1 1 O Output OUT B 7 7 O Output OUT C 8 8 O Output OUT D 14 14 O Output V+ 4 4 — Positive (highest) supply V– 11 11 — Negative (lowest) supply 4 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 6 Specifications 6.1 Absolute Maximum Ratings Over operating free-air temperature range, unless otherwise noted. (1) MIN Supply voltage Signal input terminals MAX V Voltage (V–) – 0.5 (V+) + 0.5 V Current –10 10 mA 150 °C 150 °C 150 °C Output short circuit (2) Continuous Operating temperature –55 Junction temperature Storage temperature (1) (2) UNIT ±20 –65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Short-circuit to ground, one amplifier per package. 6.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) UNIT ±4000 Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) V ±750 JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN Supply voltage (V+ – V–) Specified temperature NOM MAX UNIT 4.5 (±2.25) 36 (±18) V –40 125 °C Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 5 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com 6.4 Thermal Information: OPA171 OPA171 THERMAL METRIC (1) D (SO) DBV (SOT23) DRL (SOT553) 8 PINS 5 PINS 5 PINS UNIT 208.1 °C/W RθJA Junction-to-ambient thermal resistance 149.5 245.8 RθJC(top) Junction-to-case(top) thermal resistance 97.9 133.9 0.1 °C/W RθJB Junction-to-board thermal resistance 87.7 83.6 42.4 °C/W ψJT Junction-to-top characterization parameter 35.5 18.2 0.5 °C/W ψJB Junction-to-board characterization parameter 89.5 83.1 42.2 °C/W RθJC(bot) Junction-to-case(bottom) thermal resistance N/A N/A N/A °C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. 6.5 Thermal Information: OPA2171 OPA2171 THERMAL METRIC (1) D (SO) DGK (MSOP) DCU (VSSOP) 8 PINS 8 PINS 8 PINS UNIT RθJA Junction-to-ambient thermal resistance 134.3 175.2 195.3 °C/W RθJC(top) Junction-to-case(top) thermal resistance 72.1 74.9 59.4 °C/W RθJB Junction-to-board thermal resistance 60.6 22.2 115.1 °C/W ψJT Junction-to-top characterization parameter 18.2 1.6 4.7 °C/W ψJB Junction-to-board characterization parameter 53.8 22.8 114.4 °C/W RθJC(bot) Junction-to-case(bottom) thermal resistance N/A N/A N/A °C/W (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. 6.6 Thermal Information: OPA4171 OPA4171 THERMAL METRIC (1) D (SOIC) PW (TSSOP) 14 PINS 14 PINS UNIT RθJA Junction-to-ambient thermal resistance 93.2 106.9 °C/W RθJC(top) Junction-to-case(top) thermal resistance 51.8 24.4 °C/W RθJB Junction-to-board thermal resistance 49.4 59.3 °C/W ψJT Junction-to-top characterization parameter 13.5 0.6 °C/W ψJB Junction-to-board characterization parameter 42.2 54.3 °C/W RθJC(bot) Junction-to-case(bottom) thermal resistance N/A N/A °C/W (1) 6 For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 6.7 Electrical Characteristics at TA = 25°C, VS = 2.7 to 36 V, VCM = VOUT = VS / 2, and RLOAD = 10 kΩ connected to VS / 2, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT mV OFFSET VOLTAGE Input offset voltage VOS Over temperature 0.25 ±1.8 TA = –40°C to 125°C 0.3 ±2 mV 0.3 ±2 µV/°C ±3 µV/V Drift dVOS/dT TA = –40°C to 125°C vs power supply PSRR VS = 4 to 36 V, TA = –40°C to 125°C 1 DC 5 Channel separation, dc µV/V INPUT BIAS CURRENT Input bias current IB Over temperature Input offset current ±8 TA = –40°C to 125°C IOS Over temperature ±15 pA ±3.5 nA ±4 pA TA = –40°C to 125°C ±3.5 nA NOISE Input voltage noise Input voltage noise density f = 0.1 Hz to 10 Hz en 3 µVPP f = 100 Hz 25 nV/√Hz f = 1 kHz 14 nV/√Hz INPUT VOLTAGE Common-mode voltage range (1) Common-mode rejection ratio VCM CMRR (V–) – 0.1 V (V+) – 2 V V VS = ±2 V, (V–) – 0.1 V < VCM < (V+) – 2 V, TA = –40°C to 125°C 90 104 dB VS = ±18V, (V–) – 0.1V < VCM < (V+) – 2 V, TA = –40°C to 125°C 104 120 dB INPUT IMPEDANCE Differential MΩ || pF 100 || 3 Common-mode 6 || 3 1012Ω || pF 130 dB 3.0 MHz 1.5 V/µs OPEN-LOOP GAIN Open-loop voltage gain AOL VS = 4 V to 36 V, (V–) + 0.35 V < VO < (V+) – 0.35 V, TA = –40°C to 125°C 110 FREQUENCY RESPONSE Gain bandwidth product GBP Slew rate SR G = +1 To 0.1%, VS = ±18 V, G = +1, 10-V step Settling time tS Overload recovery time Total harmonic distortion + noise To 0.01% (12 bit), VS = ±18V, G = +1, 10V step VIN × Gain > VS THD+N G = +1, f = 1kHz, VO = 3VRMS VO VS = 5V, RL = 10kΩ 6 µs 10 µs 2 µs 0.0002% OUTPUT Voltage output swing from rail RL = 10 kΩ, AOL ≥ 110 dB, TA = –40°C to 125°C Over temperature Short-circuit current ISC Capacitive load drive CLOAD Open-loop output resistance RO (1) 30 (V–) + 0.35 mV (V+) – 0.35 +25/–35 See Typical Characteristics f = 1MHz, IO = 0A 150 V mA pF Ω The input range can be extended beyond (V+) – 2V up to V+. See Typical Characteristics and Application and Implementation for additional information. Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 7 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com Electrical Characteristics (continued) at TA = 25°C, VS = 2.7 to 36 V, VCM = VOUT = VS / 2, and RLOAD = 10 kΩ connected to VS / 2, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT POWER SUPPLY Specified voltage range VS Quiescent current per amplifier IQ Over temperature 2.7 IO = 0A 475 IO = 0 A, TA = –40°C to 125°C 36 V 595 µA 650 µA TEMPERATURE Specified range –40 125 °C Operating range –55 150 °C 8 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 6.8 Typical Characteristics Table 1. Characteristic Performance Measurements DESCRIPTION FIGURE Offset Voltage Production Distribution Figure 1 Offset Voltage Drift Distribution Figure 2 Offset Voltage vs Temperature Figure 3 Offset Voltage vs Common-Mode Voltage Figure 4 Offset Voltage vs Common-Mode Voltage (Upper Stage) Figure 5 Offset Voltage vs Power Supply Figure 6 IB and IOS vs Common-Mode Voltage Figure 7 Input Bias Current vs Temperature Figure 8 Output Voltage Swing vs Output Current (Maximum Supply) Figure 9 CMRR and PSRR vs Frequency (Referred-to Input) Figure 10 CMRR vs Temperature Figure 11 PSRR vs Temperature Figure 12 0.1-Hz to 10-Hz Noise Figure 13 Input Voltage Noise Spectral Density vs Frequency Figure 14 THD+N Ratio vs Frequency Figure 15 THD+N vs Output Amplitude Figure 16 Quiescent Current vs Temperature Figure 17 Quiescent Current vs Supply Voltage Figure 18 Open-Loop Gain and Phase vs Frequency Figure 19 Closed-Loop Gain vs Frequency Figure 20 Open-Loop Gain vs Temperature Figure 21 Open-Loop Output Impedance vs Frequency Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Figure 22 Figure 23, Figure 24 No Phase Reversal Figure 25 Positive Overload Recovery Figure 26 Negative Overload Recovery Figure 27 Small-Signal Step Response (100 mV) Figure 28, Figure 29 Large-Signal Step Response Figure 30, Figure 31 Large-Signal Settling Time (10-V Positive Step) Figure 32 Large-Signal Settling Time (10-V Negative Step) Figure 33 Short-Circuit Current vs Temperature Figure 34 Maximum Output Voltage vs Frequency Figure 35 Channel Separation vs Frequency Figure 36 Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 9 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. 25 Distribution Taken From 3500 Amplifiers Distribution Taken From 110 Amplifiers 14 Percentage of Amplifiers (%) Percentage of Amplifiers (%) 16 12 10 8 6 4 2 0 20 15 10 5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 -1200 -1100 -1000 -900 -800 -700 -600 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 0 Offset Voltage Drift (mV/°C) Offset Voltage (mV) Figure 2. Offset Voltage Drift Distribution Figure 1. Offset Voltage Production Distribution 1000 600 5 Typical Units Shown 10 Typical Units Shown 800 400 400 VOS (mV) Offset Voltage (mV) 600 200 0 -200 200 0 -200 -400 -400 -600 -600 -800 -800 VCM = -18.1V -1000 -75 -50 -25 0 25 50 75 100 125 150 -20 -15 -10 0 -5 Figure 3. Offset Voltage vs Temperature 10000 5 10 15 20 VCM (V) Temperature (°C) Figure 4. Offset Voltage vs Common-Mode Voltage 350 10 Typical Units Shown 8000 VSUPPLY = ±1.35V to ±18V 10 Typical Units Shown 250 6000 150 2000 VOS (mV) VOS (mV) 4000 0 -2000 -4000 Normal Operation -250 -8000 -10000 15.5 -50 -150 VCM = +18.1V -6000 50 -350 16 16.5 17 17.5 18 18.5 0 2 4 VCM (V) Submit Documentation Feedback 8 10 12 14 16 18 20 VSUPPLY (V) Figure 5. Offset Voltage vs Common-Mode Voltage (Upper Stage) 10 6 Figure 6. Offset Voltage vs Power Supply Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 10000 IB+ -IB +IB -IOS VCM = -18.1V IB- 1000 Input Bias Current (pA) IB and IOS (pA) VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. IB IOS 100 10 IOS 1 VCM = 16V 0 -20 -18 -12 0 -6 6 12 18 20 -75 -50 0 -25 VCM (V) Figure 7. IB and IOS vs Common-Mode Voltage 75 100 125 150 Figure 8. Input Bias Current vs Temperature Common-Mode Rejection Ratio (dB), Power-Supply Rejection Ratio (dB) 17 Output Voltage (V) 50 140 18 16 15 14.5 -14.5 -15 -40°C +25°C +85°C +125°C -16 -17 120 100 80 60 40 +PSRR -PSRR CMRR 20 0 -18 0 2 4 6 8 10 12 14 1 16 10 100 1k 10k 100k 1M 10M Frequency (Hz) Output Current (mA) Figure 9. Output Voltage Swing vs Output Current (Maximum Supply) Figure 10. CMRR and PSRR vs Frequency (Referred-to Input) 30 3 Power-Supply Rejection Ratio (mV/V) Common-Mode Rejection Ratio (mV/V) 25 Temperature (°C) 20 10 0 -10 VS = 2.7V -20 VS = 4V VS = 36V -30 2 1 0 -1 -2 VS = 2.7V to 36V VS = 4V to 36V -3 -75 -50 -25 0 25 50 75 100 125 150 -75 -50 -25 0 25 50 75 100 Temperature (°C) Temperature (°C) Figure 11. CMRR vs Temperature Figure 12. PSRR vs Temperature Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 125 150 Submit Documentation Feedback 11 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. 1mV/div Voltage Noise Density (nV/ÖHz) 1000 100 10 1 Time (1s/div) 1 10 100 1k 10k 100k 1M Frequency (Hz) Figure 13. 0.1-Hz to 10-Hz Noise -120 0.0001 G = +1, RL = 10kW G = -1, RL = 2kW 0.00001 10 100 1k 10k -140 20k Total Harmonic Distortion + Noise (%) Total Harmonic Distortion + Noise (%) -100 0.001 0.1 BW = 80kHz 0.01 -100 0.001 -120 0.0001 G = +1, RL = 10kW G = -1, RL = 2kW 0.00001 0.01 -140 0.1 1 10 20 Output Amplitude (VRMS) Frequency (Hz) Figure 15. THD+N Ratio vs Frequency Figure 16. THD+N vs Output Amplitude 0.65 0.6 0.6 0.55 0.5 IQ (mA) 0.55 IQ (mA) -80 Total Harmonic Distortion + Noise (dB) -80 VOUT = 3VRMS BW = 80kHz Total Harmonic Distortion + Noise (dB) 0.01 Figure 14. Input Voltage Noise Spectral Density vs Frequency 0.5 0.45 0.45 0.4 0.35 0.4 0.3 0.35 0.25 Specified Supply-Voltage Range -75 -50 -25 0 25 50 75 100 125 150 0 4 8 Figure 17. Quiescent Current vs Temperature 12 Submit Documentation Feedback 12 16 20 24 28 32 36 Supply Voltage (V) Temperature (°C) Figure 18. Quiescent Current vs Supply Voltage Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. 180 180 25 Gain 20 135 135 15 Phase 45 45 Gain (dB) 90 Phase (°) Gain (dB) 10 90 5 0 -5 -10 0 0 G = 10 G=1 G = -1 -15 -45 10M -45 1 10 100 1k 10k 100k 1M -20 10k 100k 1M Figure 19. Open-Loop Gain and Phase vs Frequency 3 Figure 20. Closed-Loop Gain vs Frequency 5 Typical Units Shown VS = 2.7V VS = 4V VS = 36V 100k 10k ZO (W) 2 1.5 1 1k 100 10 0.5 1 0 1m -75 -50 -25 0 25 50 75 100 150 125 1 10 100 Temperature (°C) 50 100k 1M 10M 50 ROUT = 0W 40 40 ROUT = 25W 35 35 ROUT = 50W 30 25 20 10 ROUT = 25W 5 ROUT = 50W G = +1 +18V ROUT = 0W Overshoot (%) 45 15 10k Figure 22. Open-Loop Output Impedance vs Frequency RL = 10kW 45 1k Frequency (Hz) Figure 21. Open-Loop Gain vs Temperature Overshoot (%) 100M 1M 2.5 AOL (mV/V) 10M Frequency (Hz) Frequency (Hz) 30 25 20 RI = 10kW 15 ROUT -18V RF = 10kW G = -1 +18V OPA171 RL CL 10 ROUT OPA171 CL 5 -18V 0 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Capacitive Load (pF) Figure 23. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Figure 24. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 13 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. +18V Output VOUT OPA171 VIN 5V/div 5V/div -18V 37VPP Sine Wave (±18.5V) 20kW +18V 2kW OPA171 Output VOUT VIN -18V G = -10 Time (5ms/div) Time (100ms/div) Figure 25. No Phase Reversal Figure 26. Positive Overload Recovery RL = 10kW CL = 100pF +18V OPA171 RL CL 20mV/div -18V VIN 5V/div G = +1 20kW +18V 2kW OPA171 VOUT VIN VOUT -18V G = -10 Time (1ms/div) Time (5ms/div) Figure 27. Negative Overload Recovery Figure 28. Small-Signal Step Response (100 mV) G = +1 RL = 10kW CL = 100pF RI = 2kW RF 2V/div 20mV/div CL = 100pF = 2kW +18V OPA171 CL -18V G = -1 Time (20ms/div) Time (5ms/div) Figure 29. Small-Signal Step Response (100 mV) 14 Submit Documentation Feedback Figure 30. Large-Signal Step Response Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 VS = ±18 V, VCM = VS / 2, RLOAD = 10 kΩ connected to VS / 2, and CL = 100 pF, unless otherwise noted. 10 G = -1 RL = 10kW CL = 100pF G = -1 2V/div D From Final Value (mV) 8 6 4 12-Bit Settling 2 0 -2 (±1/2LSB = ±0.024%) -4 -6 -8 -10 Time (4ms/div) 0 4 8 12 16 20 24 28 32 36 Time (ms) Figure 31. Large-Signal Step Response 10 50 G = -1 8 45 6 40 4 35 12-Bit Settling 2 ISC (mA) D From Final Value (mV) Figure 32. Large-Signal Settling Time (10-V Positive Step) 0 -2 (±1/2LSB = ±0.024%) ISC, Sink 30 25 20 -4 15 -6 10 -8 5 ISC, Source 0 -10 0 4 8 12 16 20 24 28 32 36 -75 -50 -25 0 25 50 75 100 125 150 Time (ms) Temperature (°C) Figure 33. Large-Signal Settling Time (10-V Negative Step) Figure 34. Short-Circuit Current vs Temperature 15 -60 VS = ±15V 10 Channel Separation (dB) Output Voltage (VPP) 12.5 Maximum output voltage without slew-rate induced distortion. 7.5 VS = ±5V 5 2.5 -70 -80 -90 -100 -110 VS = ±1.35V 0 -120 10k 100k 1M 10M 10 100 Frequency (Hz) Figure 35. Maximum Output Voltage vs Frequency 1k 10k 100k Frequency (Hz) Figure 36. Channel Separation vs Frequency Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 15 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com 7 Detailed Description 7.1 Overview The OPAx171 family of operational amplifiers provide high overall performance, making them ideal for many general-purpose applications. The excellent offset drift of only 2 µV/°C provides excellent stability over the entire temperature range. In addition, the device offers very good overall performance with high CMRR, PSRR, and AOL. As with all amplifiers, applications with noisy or high-impedance power supplies require decoupling capacitors close to the device pins. In most cases, 0.1-µF capacitors are adequate. 7.2 Functional Block Diagram OPA172 PCH FF Stage Ca Cb +IN PCH Input Stage Output Stage 2nd Stage OUT -IN NCH Input Stage 7.3 Feature Description 7.3.1 Operating Characteristics The OPAx171 family of amplifiers is specified for operation from 2.7 to 36 V (±1.35 to ±18 V). Many of the specifications apply from –40°C to 125°C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in Typical Characteristics. 7.3.2 Common-Mode Voltage Range The input common-mode voltage range of the OPAx171 series extends 100 mV below the negative rail and within 2 V of the top rail for normal operation. This device can operate with full rail-to-rail input 100 mV beyond the top rail, but with reduced performance within 2 V of the top rail. The typical performance in this range is summarized in Table 2. 16 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 Feature Description (continued) 7.3.3 Phase-Reversal Protection The OPAx171 family has an internal phase-reversal protection. Many operational amplifiers exhibit a phase reversal when the input is driven beyond its linear common-mode range. This condition is most often encountered in noninverting circuits when the input is driven beyond the specified common-mode voltage range, causing the output to reverse into the opposite rail. The input of the OPAx171 prevents phase reversal with excessive common-mode voltage. Instead, the output limits into the appropriate rail. This performance is shown in Figure 37. +18V Output OPA171 5V/div -18V 37VPP Sine Wave (±18.5V) Output Time (100ms/div) Figure 37. No Phase Reversal Table 2. Typical Performance Range PARAMETER Input Common-Mode Voltage MIN TYP (V+) – 2 Offset voltage vs Temperature MAX UNIT (V+) + 0.1 V 7 mV 12 µV/°C Common-mode rejection 65 dB Open-loop gain 60 dB GBW 0.7 MHz Slew rate 0.7 V/µs Noise at f = 1kHz 30 nV/√Hz 7.3.4 Capacitive Load and Stability The dynamic characteristics of the OPAx171-Q1 family of devices have been optimized for commonly encountered operating conditions. The combination of low closed-loop gain and high capacitive loads decreases the phase margin of the amplifier and can lead to gain peaking or oscillations. As a result, heavier capacitive loads must be isolated from the output. The simplest way to achieve this isolation is to add a small resistor (for example, ROUT equal to 50 Ω) in series with the output. Figure 38 and Figure 39 show small-signal overshoot versus capacitive load for several values of ROUT. Also, for details of analysis techniques and application circuits, refer to the Applications Bulletin AB-028 (SBOA015), available for download from TI.com. Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 17 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 50 50 RL = 10kW ROUT = 0W 40 40 ROUT = 25W 35 35 ROUT = 50W 30 25 20 10 ROUT = 25W 5 ROUT = 50W G = +1 +18V ROUT = 0W 15 Overshoot (%) 45 45 Overshoot (%) www.ti.com 30 25 20 RI = 10kW 15 ROUT -18V RF = 10kW G = -1 +18V OPA171 RL CL 10 ROUT OPA171 CL 5 -18V 0 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Capacitive Load (pF) Figure 38. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Figure 39. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) 7.4 Device Functional Modes 7.4.1 Common-Mode Voltage Range The input common-mode voltage range of the OPAx171 family of devices extends 100 mV below the negative rail and within 2 V of the top rail for normal operation. This device can operate with full rail-to-rail input 100 mV beyond the top rail, but with reduced performance within 2 V of the top rail. The typical performance in this range is summarized in Table 2. 18 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The OPAx171 operational amplifier provides high overall performance, making it ideal for many general-purpose applications. The excellent offset drift of only 2 µV/°C provides excellent stability over the entire temperature range. In addition, the device offers very-good overall performance with high CMRR, PSRR, and AOL. As with all amplifiers, applications with noisy or high-impedance power supplies require decoupling capacitors close to the device pins. In most cases, 0.1-µF capacitors are adequate. 8.1.1 Electrical Overstress Designers often ask questions about the capability of an operational amplifier to withstand electrical overstress. These questions tend to focus on the device inputs, but may involve the supply voltage pins or even the output pin. Each of these different pin functions have electrical stress limits determined by the voltage breakdown characteristics of the particular semiconductor fabrication process and specific circuits connected to the pin. Additionally, internal electrostatic discharge (ESD) protection is built into these circuits to protect them from accidental ESD events both before and during product assembly. These ESD protection diodes also provide in-circuit, input overdrive protection, as long as the current is limited to 10mA as stated in the Absolute Maximum Ratings. Figure 40 shows how a series input resistor may be added to the driven input to limit the input current. The added resistor contributes thermal noise at the amplifier input and its value should be kept to a minimum in noise-sensitive applications. V+ IOVERLOAD 10mA max OPA171 VOUT VIN 5kW Figure 40. Input Current Protection An ESD event produces a short duration, high-voltage pulse that is transformed into a short duration, highcurrent pulse as it discharges through a semiconductor device. The ESD protection circuits are designed to provide a current path around the operational amplifier core to prevent it from being damaged. The energy absorbed by the protection circuitry is then dissipated as heat. When the operational amplifier connects into a circuit, the ESD protection components are intended to remain inactive and not become involved in the application circuit operation. However, circumstances may arise where an applied voltage exceeds the operating voltage range of a given pin. Should this condition occur, there is a risk that some of the internal ESD protection circuits may be biased on, and conduct current. Any such current flow occurs through ESD cells and rarely involves the absorption device. If there is an uncertainty about the ability of the supply to absorb this current, external zener diodes may be added to the supply pins. The Zener voltage must be selected such that the diode does not turn on during normal operation. However, its Zener voltage should be low enough so that the zener diode conducts if the supply pin begins to rise above the safe operating supply voltage level. Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 19 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com 8.2 Typical Application +VS VOUT RISO + CLOAD + ± VIN -VS Figure 41. Unity-Gain Buffer With RISO Stability Compensation 8.2.1 Design Requirements The design requirements are: • Supply voltage: 30 V (±15 V) • Capacitive loads: 100 pF, 1000 pF, 0.01 μF, 0.1 μF, and 1 μF • Phase margin: 45° and 60° 8.2.2 Detailed Design Procedure Figure 42 shows a unity-gain buffer driving a capacitive load. Equation 1 shows the transfer function for the circuit in Figure 42. Not shown in Figure 42 is the open-loop output resistance of the operational amplifier, Ro. 1 + CLOAD × RISO × s T(s) = 1 + Ro + RISO × CLOAD × s (1) The transfer function in Equation 1 has a pole and a zero. The frequency of the pole (fp) is determined by (Ro + RISO) and CLOAD. Components RISO and CLOAD determine the frequency of the zero (fz). A stable system is obtained by selecting RISO such that the rate of closure (ROC) between the open-loop gain (AOL) and 1/β is 20 dB/decade. Figure 42 depicts the concept. The 1/β curve for a unity-gain buffer is 0 dB. 120 AOL 100 1 fp 2 u u RISO R o Gain (dB) 80 60 u CLOAD 40 dB fz 40 1 2 u u RISO u CLOAD 1 dec 1/ 20 ROC 20 dB dec 0 10 100 1k 10k 100k 1M 10M 100M Frequency (Hz) Figure 42. Unity-Gain Amplifier With RISO Compensation 20 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 Typical Application (continued) ROC stability analysis is typically simulated. The validity of the analysis depends on multiple factors, especially the accurate modeling of Ro. In addition to simulating the ROC, a robust stability analysis includes a measurement of overshoot percentage and AC gain peaking of the circuit using a function generator, oscilloscope, and gain and phase analyzer. Phase margin is then calculated from these measurements. Table 3 shows the overshoot percentage and AC gain peaking that correspond to phase margins of 45° and 60°. For more details on this design and other alternative devices that can be used in place of the OPA171, refer to the Precision Design, Capacitive Load Drive Solution using an Isolation Resistor (TIPD128). Table 3. Phase Margin versus Overshoot and AC Gain Peaking PHASE MARGIN OVERSHOOT AC GAIN PEAKING 45° 23.3% 2.35 dB 60° 8.8% 0.28 dB 8.2.2.1 Capacitive Load and Stability The dynamic characteristics of the OPAx171 have been optimized for commonly encountered operating conditions. The combination of low closed-loop gain and high capacitive loads decreases the phase margin of the amplifier and can lead to gain peaking or oscillations. As a result, heavier capacitive loads must be isolated from the output. The simplest way to achieve this isolation is to add a small resistor (for example, ROUT equal to 50 Ω) in series with the output. Figure 38 and Figure 39 illustrate graphs of small-signal overshoot versus capacitive load for several values of ROUT. Also, refer to Applications Bulletin AB-028 (SBOA015), available for download from the TI website for details of analysis techniques and application circuits. 50 45 ROUT = 0W 40 40 ROUT = 25W 35 35 ROUT = 50W 30 25 20 15 ROUT = 0W 10 ROUT = 25W 5 ROUT = 50W G = +1 +18V Overshoot (%) Overshoot (%) 50 RL = 10kW 45 30 25 20 RI = 10kW 15 ROUT -18V RF = 10kW G = -1 +18V OPA171 RL CL 10 ROUT OPA171 CL 5 -18V 0 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Capacitive Load (pF) Figure 43. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Figure 44. Small-Signal Overshoot vs Capacitive Load (100-mV Output Step) Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 21 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com 8.2.3 Application Curve The OPA171 meets the supply voltage requirements of 30 V. The OPA171 is tested for various capacitive loads and RISO is adjusted to get an overshoot corresponding to Table 3. The results of the these tests are summarized in Figure 45. 10000 Isolation Resistor, RISO (:) 45q Phase Margin 60q Phase Margin 1000 100 10 1 0.01 0.1 1 10 Capacitive Load (nF) 100 1000 D001 Figure 45. RISO vs CLOAD 22 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 OPA171, OPA2171, OPA4171 www.ti.com SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 9 Power Supply Recommendations The OPAx171 family of devices is specified for operation from 4.5 V to 36 V (±2.25 V to ±18 V); many specifications apply from –40°C to 125°C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Specifications section. CAUTION Supply voltages larger than 40 V can permanently damage the device; see the Absolute Maximum Ratings table. Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or highimpedance power supplies. For detailed information on bypass capacitor placement, see the Layout Guidelines section. 10 Layout 10.1 Layout Guidelines For best operational performance of the device, good printed--circuit board (PCB) layout practices are recommended. Low-loss, 0.1-µF bypass capacitors should be connected between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable to singlesupply applications. 10.2 Layout Example RIN + VIN VOUT RG RF (Schematic Representation) Run the input traces as far away from the supply lines as possible Place components close to device and to each other to reduce parasitic errors VS+ RF NC NC ±IN V+ +IN OUT V± NC RG GND VIN GND RIN Only needed for dual-supply operation GND VS± (or GND for single supply) Use low-ESR, ceramic bypass capacitor VOUT Ground (GND) plane on another layer Figure 46. Operational Amplifier Board Layout for Noninverting Configuration Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 Submit Documentation Feedback 23 OPA171, OPA2171, OPA4171 SBOS516E – SEPTEMBER 2010 – REVISED JUNE 2015 www.ti.com 11 Device and Documentation Support 11.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 4. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY OPA171 Click here Click here Click here Click here Click here OPA2171 Click here Click here Click here Click here Click here OPA4171 Click here Click here Click here Click here Click here 11.2 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.3 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.4 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.5 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 24 Submit Documentation Feedback Copyright © 2010–2015, Texas Instruments Incorporated Product Folder Links: OPA171 OPA2171 OPA4171 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) OPA171AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 O171A OPA171AIDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 OSUI OPA171AIDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 OSUI OPA171AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 O171A OPA171AIDRLR ACTIVE SOT DRL 5 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 DAP OPA171AIDRLT ACTIVE SOT DRL 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 DAP OPA2171AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 2171A OPA2171AIDCUR ACTIVE VSSOP DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 OPOC OPA2171AIDCUT ACTIVE VSSOP DCU 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 OPOC OPA2171AIDGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAG Level-2-260C-1 YEAR -40 to 125 OPMI OPA2171AIDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAG Level-2-260C-1 YEAR -40 to 125 OPMI OPA2171AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 2171A OPA4171AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 125 OPA4171 OPA4171AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR -40 to 125 OPA4171 OPA4171AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 OPA4171 OPA4171AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 125 OPA4171 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2015 LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF OPA171, OPA2171, OPA4171 : • Automotive: OPA171-Q1, OPA2171-Q1, OPA4171-Q1 NOTE: Qualified Version Definitions: • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 19-Aug-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) OPA171AIDBVR SOT-23 DBV 5 3000 179.0 8.4 OPA171AIDBVR SOT-23 DBV 5 3000 180.0 OPA171AIDBVT SOT-23 DBV 5 250 180.0 OPA171AIDBVT SOT-23 DBV 5 250 OPA171AIDR SOIC D 8 OPA171AIDRLR SOT DRL OPA171AIDRLT SOT DRL OPA2171AIDCUR VSSOP W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.23 3.17 1.37 4.0 8.0 Q3 8.4 3.23 3.17 1.37 4.0 8.0 Q3 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 5 4000 180.0 8.4 1.98 1.78 0.69 4.0 8.0 Q3 5 250 180.0 8.4 1.98 1.78 0.69 4.0 8.0 Q3 DCU 8 3000 180.0 8.4 2.25 3.35 1.05 4.0 8.0 Q3 OPA2171AIDCUT VSSOP DCU 8 250 180.0 8.4 2.25 3.35 1.05 4.0 8.0 Q3 OPA2171AIDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2171AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4171AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 19-Aug-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA171AIDBVR SOT-23 DBV 5 3000 195.0 200.0 45.0 OPA171AIDBVR SOT-23 DBV 5 3000 202.0 201.0 28.0 OPA171AIDBVT SOT-23 DBV 5 250 223.0 270.0 35.0 OPA171AIDBVT SOT-23 DBV 5 250 195.0 200.0 45.0 OPA171AIDR SOIC D 8 2500 367.0 367.0 35.0 OPA171AIDRLR SOT DRL 5 4000 202.0 201.0 28.0 OPA171AIDRLT SOT DRL 5 250 202.0 201.0 28.0 OPA2171AIDCUR VSSOP DCU 8 3000 202.0 201.0 28.0 OPA2171AIDCUT VSSOP DCU 8 250 202.0 201.0 28.0 OPA2171AIDGKR VSSOP DGK 8 2500 366.0 364.0 50.0 OPA2171AIDR SOIC D 8 2500 367.0 367.0 35.0 OPA4171AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated