TI1 OPA171AIDBVT 36v, single-supply, sot553, general-purpose operational amplifier Datasheet

OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
36V, Single-Supply, SOT553, General-Purpose
OPERATIONAL AMPLIFIERS
Check for Samples: OPA171, OPA2171, OPA4171
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
•
The OPA171, OPA2171 and OPA4171 (OPAx171)
are a family of 36V, single-supply, low-noise
operational amplifiers with the ability to operate on
supplies ranging from +2.7V (±1.35V) to +36V
(±18V).
These
devices
are
available
in
micro-packages and offer low offset, drift, and
bandwidth with low quiescent current. The single,
dual, and quad versions all have identical
specifications for maximum design flexibility.
1
2
•
Supply Range: +2.7V to +36V, ±1.35V to ±18V
Low Noise: 14nV/√Hz
Low Offset Drift: ±0.3µV/°C (typ)
RFI Filtered Inputs
Input Range Includes the Negative Supply
Input Range Operates to Positive Supply
Rail-to-Rail Output
Gain Bandwidth: 3MHz
Low Quiescent Current: 475µA per Amplifier
High Common-Mode Rejection: 120dB (typ)
Low Input Bias Current: 8pA
Industry-Standard Packages:
– 8-Pin SOIC
– 8-Pin MSOP
– 14-Pin TSSOP
microPackages:
– Single in SOT553
– Dual in VSSOP-8
APPLICATIONS
•
•
•
•
•
•
•
•
•
Unlike most op amps, which are specified at only one
supply voltage, the OPAx171 family is specified from
+2.7V to +36V. Input signals beyond the supply rails
do not cause phase reversal. The OPAx171 family is
stable with capacitive loads up to 300pF. The input
can operate 100mV below the negative rail and within
2V of the top rail during normal operation. Note that
these devices can operate with full rail-to-rail input
100mV beyond the top rail, but with reduced
performance within 2V of the top rail.
The OPAx171 series of op amps are specified
from –40°C to +125°C.
Package Footprint Comparison (to Scale)
Tracking Amplifier in Power Modules
Merchant Power Supplies
Transducer Amplifiers
Bridge Amplifiers
Temperature Measurements
Strain Gauge Amplifiers
Precision Integrators
Battery-Powered Instruments
Test Equipment
Product Family
DEVICE
PACKAGE
OPA171
SOT553, SOT23-5, SO-8
OPA2171 (dual)
VSSOP-8, SO-8, MSOP-8
OPA4171 (quad)
TSSOP-14, SO-14
Package Height Comparison (to Scale)
D (SO-8)
DBV (SOT23-5)
DRL (SOT553)
Smallest Packaging for 36V Op Amps
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE-LEAD
PACKAGE
DESIGNATOR
PACKAGE
MARKING
SOT553
DRL
DAP
OPA171
OPA2171
SOT23-5
DBV
OSUI
SO-8
D
O171A
MSOP-8
DGK
OPMI
VSSOP-8
DCU
OPOC
SO-8
D
2171A
SO-14
D
OPA4171
TSSOP-14
PW
OPA4171
OPA4171
(1)
(1)
ORDERING NUMBER
TRANSPORT MEDIA,
QUANTITY
OPA171AIDRLT
Tape and Reel, 250
OPA171AIDRLR
Tape and Reel, 4000
OPA171AIDBVT
Tape and Reel, 250
OPA171AIDBVR
Tape and Reel, 3000
OPA171AID
Rail, 75
OPA171AIDR
Tape and Reel, 2500
OPA2171AIDGK
Rail, 80
OPA2171AIDGKR
Tape and Reel, 2500
OPA2171AIDCUT
Tape and Reel, 250
OPA2171AIDCUR
Tape and Reel, 3000
OPA2171AID
Rail, 75
OPA2171AIDR
Tape and Reel, 2500
OPA4171AID
Rail, 50
OPA4171AIDR
Tape and Reel, 2500
OPA4171AIPW
Rail, 90
OPA4171AIPWR
Tape and Reel, 2000
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
Supply voltage
Signal input terminals
OPAx171
UNIT
±20
V
Voltage
(V–) – 0.5 to (V+) + 0.5
V
Current
±10
mA
Output short circuit (2)
Continuous
Operating temperature
–55 to +150
°C
Storage temperature
–65 to +150
°C
Junction temperature
+150
°C
4
kV
750
V
ESD ratings:
(1)
(2)
2
Human body model (HBM)
Charged device model (CDM)
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
Short-circuit to ground, one amplifier per package.
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, TA = –40°C to +125°C.
At TA = +25°C, VS = +2.7V to +36V, VCM = VOUT = VS/2, and RLOAD = 10kΩ connected to VS/2, unless otherwise noted.
OPA171, OPA2171, OPA4171
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
0.25
±1.8
mV
0.3
±2
mV
OFFSET VOLTAGE
Input offset voltage
VOS
Over temperature
Drift
vs power supply
0.3
±2
µV/°C
VS = +4V to +36V
1
±3
µV/V
dc
5
dVOS/dT
PSRR
Channel separation, dc
µV/V
INPUT BIAS CURRENT
Input bias current
±8
IB
Over temperature
Input offset current
±15
pA
±3.5
nA
±3.5
nA
±4
IOS
pA
Over temperature
NOISE
Input voltage noise
Input voltage noise density
en
f = 0.1Hz to 10Hz
3
µVPP
f = 100Hz
25
nV/√Hz
f = 1kHz
14
nV/√Hz
INPUT VOLTAGE
Common-mode voltage range (1)
Common-mode rejection ratio
(V–) – 0.1V
VCM
CMRR
(V+) – 2V
V
VS = ±2V, (V–) – 0.1V < VCM < (V+) – 2V
90
104
dB
VS = ±18V, (V–) – 0.1V < VCM < (V+) – 2V
104
120
dB
INPUT IMPEDANCE
Differential
Common-mode
100 || 3
MΩ || pF
6 || 3
1012Ω ||
pF
130
dB
3.0
MHz
1.5
V/µs
OPEN-LOOP GAIN
Open-loop voltage gain
AOL VS = +4V to +36V, (V–) + 0.35V < VO < (V+) – 0.35V
110
FREQUENCY RESPONSE
Gain bandwidth product
Slew rate
Settling time
GBP
SR
tS
G = +1
To 0.1%, VS = ±18V, G = +1, 10V step
6
µs
To 0.01% (12 bit), VS = ±18V, G = +1, 10V step
10
µs
2
µs
0.0002
%
VIN × Gain > VS
Overload recovery time
Total harmonic distortion + noise
THD+N
G = +1, f = 1kHz, VO = 3VRMS
OUTPUT
Voltage output swing from rail
VO
Short-circuit current
Capacitive load drive
Open-loop output resistance
VS = 5V, RL = 10kΩ
RL = 10kΩ, AOL ≥ 110dB
Over temperature
30
ISC
+25/–35
CLOAD
RO
mV
(V+) – 0.35
(V–) + 0.35
See Typical Characteristics
f = 1MHz, IO = 0A
V
mA
pF
Ω
150
POWER SUPPLY
Specified voltage range
VS
Quiescent current per amplifier
IQ
Over temperature
+2.7
IO = 0A
475
IO = 0A
+36
V
595
µA
650
µA
TEMPERATURE
Specified range
–40
+125
°C
Operating range
–55
+150
°C
(1)
The input range can be extended beyond (V+) – 2V up to V+. See the Typical Characteristics and Application Information sections for
additional information.
Copyright © 2010–2011, Texas Instruments Incorporated
3
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
THERMAL INFORMATION: OPA171
OPA171
THERMAL METRIC (1)
D (SO)
DBV (SOT23)
DRL (SOT553)
8 PINS
5 PINS
5 PINS
208.1
θJA
Junction-to-ambient thermal resistance
149.5
245.8
θJC(top)
Junction-to-case(top) thermal resistance
97.9
133.9
0.1
θJB
Junction-to-board thermal resistance
87.7
83.6
42.4
ψJT
Junction-to-top characterization parameter
35.5
18.2
0.5
ψJB
Junction-to-board characterization parameter
89.5
83.1
42.2
θJC(bottom)
Junction-to-case(bottom) thermal resistance
N/A
N/A
N/A
(1)
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
THERMAL INFORMATION: OPA2171
OPA2171
THERMAL METRIC (1)
D (SO)
DCU (VSSOP)
DGK (MSOP)
8 PINS
8 PINS
8 PINS
195.3
θJA
Junction-to-ambient thermal resistance
134.3
175.2
θJC(top)
Junction-to-case(top) thermal resistance
72.1
74.9
59.4
θJB
Junction-to-board thermal resistance
60.6
22.2
115.1
ψJT
Junction-to-top characterization parameter
18.2
1.6
4.7
ψJB
Junction-to-board characterization parameter
53.8
22.8
114.4
θJC(bottom)
Junction-to-case(bottom) thermal resistance
N/A
N/A
N/A
(1)
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
THERMAL INFORMATION: OPA4171
OPA4171
THERMAL METRIC (1)
D (SO)
PW (TSSOP)
14 PINS
14 PINS
θJA
Junction-to-ambient thermal resistance
93.2
106.9
θJC(top)
Junction-to-case(top) thermal resistance
51.8
24.4
θJB
Junction-to-board thermal resistance
49.4
59.3
ψJT
Junction-to-top characterization parameter
13.5
0.6
ψJB
Junction-to-board characterization parameter
42.2
54.3
θJC(bottom)
Junction-to-case(bottom) thermal resistance
N/A
N/A
(1)
4
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
PIN CONFIGURATIONS
DRL PACKAGE: OPA171
SOT-553
(TOP VIEW)
IN+
1
V-
2
IN-
3
D, DCU, AND DGK PACKAGES: OPA2171
SO-8, VSSOP-8, AND MSOP-8
(TOP VIEW)
5
V+
4
OUT
DBV PACKAGE: OPA171
SOT23-5
(TOP VIEW)
OUT
1
V-
2
+IN
3
5
V+
4
-IN
1
8
V+
-IN A
2
7
OUT B
+IN A
3
6
-IN B
V-
4
5
+IN B
D AND PW PACKAGES: OPA4171
SO-14 AND TSSOP-14
(TOP VIEW)
D PACKAGE: OPA171
SO-8
(TOP VIEW)
(1)
OUT A
NC(1)
1
8
NC(1)
-IN
2
7
V+
+IN
3
6
OUT
V-
4
5
NC(1)
OUT A
1
14
OUT D
-IN A
2
13
-IN D
+IN A
3
12
+IN D
V+
4
11
V-
+IN B
5
10
+IN C
-IN B
6
9
-IN C
OUT B
7
8
OUT C
No internal connection.
Copyright © 2010–2011, Texas Instruments Incorporated
5
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
Table 1. Characteristic Performance Measurements
6
DESCRIPTION
FIGURE
Offset Voltage Production Distribution
Figure 1
Offset Voltage Drift Distribution
Figure 2
Offset Voltage vs Temperature
Figure 3
Offset Voltage vs Common-Mode Voltage
Figure 4
Offset Voltage vs Common-Mode Voltage (Upper Stage)
Figure 5
Offset Voltage vs Power Supply
Figure 6
IB and IOS vs Common-Mode Voltage
Figure 7
Input Bias Current vs Temperature
Figure 8
Output Voltage Swing vs Output Current (Maximum Supply)
Figure 9
CMRR and PSRR vs Frequency (Referred-to Input)
Figure 10
CMRR vs Temperature
Figure 11
PSRR vs Temperature
Figure 12
0.1Hz to 10Hz Noise
Figure 13
Input Voltage Noise Spectral Density vs Frequency
Figure 14
THD+N Ratio vs Frequency
Figure 15
THD+N vs Output Amplitude
Figure 16
Quiescent Current vs Temperature
Figure 17
Quiescent Current vs Supply Voltage
Figure 18
Open-Loop Gain and Phase vs Frequency
Figure 19
Closed-Loop Gain vs Frequency
Figure 20
Open-Loop Gain vs Temperature
Figure 21
Open-Loop Output Impedance vs Frequency
Figure 22
Small-Signal Overshoot vs Capacitive Load (100mV Output Step)
Figure 23, Figure 24
No Phase Reversal
Figure 25
Positive Overload Recovery
Figure 26
Negative Overload Recovery
Figure 27
Small-Signal Step Response (100mV)
Figure 28, Figure 29
Large-Signal Step Response
Figure 30, Figure 31
Large-Signal Settling Time (10V Positive Step)
Figure 32
Large-Signal Settling Time (10V Negative Step)
Figure 33
Short-Circuit Current vs Temperature
Figure 34
Maximum Output Voltage vs Frequency
Figure 35
Channel Separation vs Frequency
Figure 36
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT DISTRIBUTION
25
Distribution Taken From 3500 Amplifiers
14
Percentage of Amplifiers (%)
Percentage of Amplifiers (%)
16
12
10
8
6
4
2
0
Distribution Taken From 110 Amplifiers
20
15
10
5
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
-1200
-1100
-1000
-900
-800
-700
-600
-500
-400
-300
-200
-100
0
100
200
300
400
500
600
700
800
900
1000
1100
1200
0
Offset Voltage Drift (mV/°C)
Offset Voltage (mV)
Figure 1.
Figure 2.
OFFSET VOLTAGE vs TEMPERATURE
OFFSET VOLTAGE vs COMMON-MODE VOLTAGE
1000
600
5 Typical Units Shown
10 Typical Units Shown
800
400
400
VOS (mV)
Offset Voltage (mV)
600
200
0
-200
200
0
-200
-400
-400
-600
-600
-800
-800
VCM = -18.1V
-1000
-75
-50
-25
0
25
50
75
100
125
150
-20
-15
-10
0
-5
Figure 3.
10
15
20
Figure 4.
OFFSET VOLTAGE vs COMMON-MODE VOLTAGE
(Upper Stage)
10000
5
VCM (V)
Temperature (°C)
OFFSET VOLTAGE vs POWER SUPPLY
350
10 Typical Units Shown
8000
VSUPPLY = ±1.35V to ±18V
10 Typical Units Shown
250
6000
150
2000
VOS (mV)
VOS (mV)
4000
0
-2000
-4000
Normal
Operation
-250
-8000
-10000
15.5
-50
-150
VCM = +18.1V
-6000
50
-350
16
16.5
17
17.5
VCM (V)
Figure 5.
Copyright © 2010–2011, Texas Instruments Incorporated
18
18.5
0
2
4
6
8
10
12
14
16
18
20
VSUPPLY (V)
Figure 6.
7
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
INPUT BIAS CURRENT vs TEMPERATURE
10000
IB+
-IB
+IB
-IOS
VCM = -18.1V
IB-
1000
Input Bias Current (pA)
IB and IOS (pA)
IB AND IOS vs COMMON-MODE VOLTAGE
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
IB
IOS
100
10
IOS
1
VCM = 16V
0
-20
-18
-12
0
-6
6
12
18
20
-75
-50
0
-25
VCM (V)
100
125
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
(Maximum Supply)
CMRR AND PSRR vs FREQUENCY
(Referred-to Input)
150
140
Common-Mode Rejection Ratio (dB),
Power-Supply Rejection Ratio (dB)
Output Voltage (V)
75
Figure 8.
17
16
15
14.5
-14.5
-15
-40°C
+25°C
+85°C
+125°C
-16
-17
120
100
80
60
40
+PSRR
-PSRR
CMRR
20
0
-18
0
2
4
6
8
10
12
14
1
16
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Output Current (mA)
Figure 9.
Figure 10.
CMRR vs TEMPERATURE
PSRR vs TEMPERATURE
30
3
Power-Supply Rejection Ratio (mV/V)
Common-Mode Rejection Ratio (mV/V)
50
Figure 7.
18
20
10
0
-10
VS = 2.7V
-20
VS = 4V
VS = 36V
-30
2
1
0
-1
-2
VS = 2.7V to 36V
VS = 4V to 36V
-3
-75
8
25
Temperature (°C)
-50
-25
0
25
50
75
100
125
150
-75
-50
-25
0
25
50
Temperature (°C)
Temperature (°C)
Figure 11.
Figure 12.
75
100
125
150
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
INPUT VOLTAGE NOISE SPECTRAL DENSITY vs
FREQUENCY
0.1Hz TO 10Hz NOISE
1mV/div
Voltage Noise Density (nV/ÖHz)
1000
100
10
1
Time (1s/div)
1
10
100
1k
10k
100k
1M
Frequency (Hz)
Figure 13.
Figure 14.
THD+N RATIO vs FREQUENCY
0.001
-100
0.0001
-120
G = +1, RL = 10kW
G = -1, RL = 2kW
0.00001
10
100
1k
10k
-140
20k
Total Harmonic Distortion + Noise (%)
VOUT = 3VRMS
BW = 80kHz
0.1
-80
BW = 80kHz
0.01
-100
0.001
-120
0.0001
G = +1, RL = 10kW
G = -1, RL = 2kW
0.00001
0.01
-140
0.1
1
10
20
Output Amplitude (VRMS)
Frequency (Hz)
Figure 15.
Figure 16.
QUIESCENT CURRENT vs TEMPERATURE
QUIESCENT CURRENT vs SUPPLY VOLTAGE
0.65
0.6
0.6
0.55
0.5
IQ (mA)
0.55
IQ (mA)
Total Harmonic Distortion + Noise (dB)
Total Harmonic Distortion + Noise (%)
THD+N vs OUTPUT AMPLITUDE
-80
Total Harmonic Distortion + Noise (dB)
0.01
0.5
0.45
0.45
0.4
0.35
0.4
0.3
0.35
0.25
Specified Supply-Voltage Range
-75
-50
-25
0
25
50
75
Temperature (°C)
Figure 17.
Copyright © 2010–2011, Texas Instruments Incorporated
100
125
150
0
4
8
12
16
20
24
28
32
36
Supply Voltage (V)
Figure 18.
9
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
OPEN-LOOP GAIN AND PHASE vs FREQUENCY
CLOSED-LOOP GAIN vs FREQUENCY
180
180
25
Gain
20
135
135
15
Phase
45
45
Gain (dB)
90
Phase (°)
Gain (dB)
10
90
5
0
-5
-10
0
0
G = 10
G=1
G = -1
-15
-45
1
10
100
1k
10k
100k
-20
-45
10M
1M
10k
100k
1M
Figure 19.
OPEN-LOOP OUTPUT IMPEDANCE vs FREQUENCY
1M
5 Typical Units Shown
VS = 2.7V
VS = 4V
VS = 36V
2.5
100k
10k
ZO (W)
AOL (mV/V)
2
1.5
1
1k
100
10
0.5
1
0
1m
-75
-50
-25
0
25
50
75
100
150
125
1
10
100
Temperature (°C)
10k
100k
1M
10M
Figure 22.
SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD
(100mV Output Step)
SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD
(100mV Output Step)
50
RL = 10kW
ROUT = 0W
40
40
ROUT = 25W
35
35
ROUT = 50W
30
25
20
15
ROUT = 0W
10
ROUT = 25W
5
ROUT = 50W
G = +1
+18V
Overshoot (%)
45
45
Overshoot (%)
1k
Frequency (Hz)
Figure 21.
50
30
25
20
RI = 10kW
15
ROUT
RF = 10kW
G = -1
+18V
OPA171
RL
CL
10
ROUT
OPA171
-18V
CL
5
-18V
0
0
0
10
100M
Figure 20.
OPEN-LOOP GAIN vs TEMPERATURE
3
10M
Frequency (Hz)
Frequency (Hz)
100 200 300 400 500 600 700 800 900 1000
0
100 200 300 400 500 600 700 800 900 1000
Capacitive Load (pF)
Capacitive Load (pF)
Figure 23.
Figure 24.
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
NO PHASE REVERSAL
POSITIVE OVERLOAD RECOVERY
+18V
Output
VOUT
OPA171
VIN
5V/div
5V/div
-18V
37VPP
Sine Wave
(±18.5V)
20kW
+18V
2kW
OPA171
Output
VOUT
VIN
-18V
G = -10
Time (5ms/div)
Time (100ms/div)
Figure 25.
Figure 26.
NEGATIVE OVERLOAD RECOVERY
SMALL-SIGNAL STEP RESPONSE
(100mV)
RL = 10kW
CL = 100pF
+18V
RL
CL
20mV/div
-18V
VIN
5V/div
G = +1
OPA171
20kW
+18V
2kW
OPA171
VOUT
VIN
VOUT
-18V
G = -10
Time (5ms/div)
Time (1ms/div)
Figure 27.
Figure 28.
SMALL-SIGNAL STEP RESPONSE
(100mV)
LARGE-SIGNAL STEP RESPONSE
G = +1
RL = 10kW
CL = 100pF
RI
= 2kW
RF
2V/div
20mV/div
CL = 100pF
= 2kW
+18V
OPA171
CL
-18V
G = -1
Time (20ms/div)
Time (5ms/div)
Figure 29.
Figure 30.
Copyright © 2010–2011, Texas Instruments Incorporated
11
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VS = ±18V, VCM = VS/2, RLOAD = 10kΩ connected to VS/2, and CL = 100pF, unless otherwise noted.
LARGE-SIGNAL SETTLING TIME
(10V Positive Step)
LARGE-SIGNAL STEP RESPONSE
10
G = -1
RL = 10kW
CL = 100pF
G = -1
2V/div
D From Final Value (mV)
8
6
4
12-Bit Settling
2
0
-2
(±1/2LSB = ±0.024%)
-4
-6
-8
-10
Time (4ms/div)
0
4
8
12
16
20
24
28
32
36
Time (ms)
Figure 31.
Figure 32.
LARGE-SIGNAL SETTLING TIME
(10V Negative Step)
10
G = -1
8
45
ISC, Sink
40
6
4
35
12-Bit Settling
2
ISC (mA)
D From Final Value (mV)
SHORT-CIRCUIT CURRENT vs TEMPERATURE
50
0
-2
(±1/2LSB = ±0.024%)
30
25
20
-4
15
-6
10
-8
5
ISC, Source
0
-10
0
4
8
12
16
20
24
28
32
36
-75
-50
-25
Time (ms)
0
25
50
75
100
125
150
Temperature (°C)
Figure 33.
Figure 34.
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
15
-60
VS = ±15V
10
Channel Separation (dB)
Output Voltage (VPP)
12.5
Maximum output voltage without
slew-rate induced distortion.
7.5
VS = ±5V
5
2.5
-80
-90
-100
-110
VS = ±1.35V
0
-120
10k
12
-70
100k
1M
10M
10
100
1k
Frequency (Hz)
Frequency (Hz)
Figure 35.
Figure 36.
10k
100k
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
APPLICATION INFORMATION
The OPAx171 family of operational amplifiers provide
high overall performance, making them ideal for many
general-purpose applications. The excellent offset
drift of only 2µV/°C provides excellent stability over
the entire temperature range. In addition, the device
offers very good overall performance with high
CMRR, PSRR, and AOL. As with all amplifiers,
applications with noisy or high-impedance power
supplies require decoupling capacitors close to the
device pins. In most cases, 0.1µF capacitors are
adequate.
OPERATING CHARACTERISTICS
The OPAx171 family of amplifiers is specified for
operation from 2.7V to 36V (±1.35V to ±18V). Many
of the specifications apply from –40°C to +125°C.
Parameters that can exhibit significant variance with
regard to operating voltage or temperature are
presented in the Typical Characteristics.
This device can operate with full rail-to-rail input
100mV beyond the top rail, but with reduced
performance within 2V of the top rail. The typical
performance in this range is summarized in Table 2.
PHASE-REVERSAL PROTECTION
The OPAx171 family has an internal phase-reversal
protection. Many op amps exhibit a phase reversal
when the input is driven beyond its linear
common-mode range. This condition is most often
encountered in noninverting circuits when the input is
driven beyond the specified common-mode voltage
range, causing the output to reverse into the opposite
rail. The input of the OPAx171 prevents phase
reversal with excessive common-mode voltage.
Instead, the output limits into the appropriate rail. This
performance is shown in Figure 37.
+18V
Output
GENERAL LAYOUT GUIDELINES
-18V
37VPP
Sine Wave
(±18.5V)
5V/div
For best operational performance of the device, good
printed circuit board (PCB) layout practices are
recommended. Low-loss, 0.1µF bypass capacitors
should be connected between each supply pin and
ground, placed as close to the device as possible. A
single bypass capacitor from V+ to ground is
applicable to single-supply applications.
OPA171
Output
COMMON-MODE VOLTAGE RANGE
Time (100ms/div)
The input common-mode voltage range of the
OPAx171 series extends 100mV below the negative
rail and within 2V of the top rail for normal operation.
Figure 37. No Phase Reversal
Table 2. Typical Performance Range
PARAMETER
Input Common-Mode Voltage
Offset voltage
MIN
TYP
(V+) – 2
MAX
(V+) + 0.1
UNIT
V
7
mV
12
µV/°C
Common-mode rejection
65
dB
Open-loop gain
60
dB
GBW
0.7
MHz
Slew rate
0.7
V/µs
Noise at f = 1kHz
30
nV/√Hz
vs Temperature
Copyright © 2010–2011, Texas Instruments Incorporated
13
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
CAPACITIVE LOAD AND STABILITY
The dynamic characteristics of the OPAx171 have
been optimized for commonly encountered operating
conditions. The combination of low closed-loop gain
and high capacitive loads decreases the phase
margin of the amplifier and can lead to gain peaking
or oscillations. As a result, heavier capacitive loads
must be isolated from the output. The simplest way to
achieve this isolation is to add a small resistor (for
example, ROUT equal to 50Ω) in series with the
output. Figure 38 and Figure 39 illustrate graphs of
small-signal overshoot versus capacitive load for
several values of ROUT. Also, refer to Applications
Bulletin AB-028 (SBOA015), available for download
from the TI website for details of analysis techniques
and application circuits.
50
or even the output pin. Each of these different pin
functions have electrical stress limits determined by
the voltage breakdown characteristics of the
particular semiconductor fabrication process and
specific circuits connected to the pin. Additionally,
internal electrostatic discharge (ESD) protection is
built into these circuits to protect them from
accidental ESD events both before and during
product assembly.
These ESD protection diodes also provide in-circuit,
input overdrive protection, as long as the current is
limited to 10mA as stated in the Absolute Maximum
Ratings. Figure 40 shows how a series input resistor
may be added to the driven input to limit the input
current. The added resistor contributes thermal noise
at the amplifier input and its value should be kept to a
minimum in noise-sensitive applications.
RL = 10kW
45
V+
Overshoot (%)
40
IOVERLOAD
10mA max
35
30
OPA171
5kW
20
15
ROUT = 0W
10
ROUT = 25W
5
ROUT = 50W
G = +1
+18V
ROUT
Figure 40. Input Current Protection
OPA171
RL
CL
-18V
0
0
100 200 300 400 500 600 700 800 900 1000
Capacitive Load (pF)
Figure 38. Small-Signal Overshoot versus
Capacitive Load (100mV Output Step)
Overshoot (%)
50
45
ROUT = 0W
40
ROUT = 25W
35
ROUT = 50W
30
25
20
RI = 10kW
15
RF = 10kW
G = -1
+18V
10
ROUT
OPA171
CL
5
-18V
0
0
100 200 300 400 500 600 700 800 900 1000
Capacitive Load (pF)
Figure 39. Small-Signal Overshoot versus
Capacitive Load (100mV Output Step)
ELECTRICAL OVERSTRESS
Designers often ask questions about the capability of
an operational amplifier to withstand electrical
overstress. These questions tend to focus on the
device inputs, but may involve the supply voltage pins
14
VOUT
VIN
25
An ESD event produces a short duration,
high-voltage pulse that is transformed into a short
duration, high-current pulse as it discharges through
a semiconductor device. The ESD protection circuits
are designed to provide a current path around the
operational amplifier core to prevent it from being
damaged. The energy absorbed by the protection
circuitry is then dissipated as heat.
When the operational amplifier connects into a circuit,
the ESD protection components are intended to
remain inactive and not become involved in the
application circuit operation. However, circumstances
may arise where an applied voltage exceeds the
operating voltage range of a given pin. Should this
condition occur, there is a risk that some of the
internal ESD protection circuits may be biased on,
and conduct current. Any such current flow occurs
through ESD cells and rarely involves the absorption
device.
If there is an uncertainty about the ability of the
supply to absorb this current, external zener diodes
may be added to the supply pins. The zener voltage
must be selected such that the diode does not turn
on during normal operation.
However, its zener voltage should be low enough so
that the zener diode conducts if the supply pin begins
to rise above the safe operating supply voltage level.
Copyright © 2010–2011, Texas Instruments Incorporated
OPA171
OPA2171
OPA4171
SBOS516C – SEPTEMBER 2010 – REVISED JUNE 2011
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (November 2010) to Revision C
Page
•
Added MSOP-8 package to device graphic .......................................................................................................................... 1
•
Added MSOP-8 package to Features bullets ....................................................................................................................... 1
•
Added MSOP-8 package to Product Family table ................................................................................................................ 1
•
Added MSOP-8 package to Package/Ordering Information table ........................................................................................ 2
•
Deleted "A" suffix from OPA4171 package markings in Package/Ordering Information table. ............................................ 2
•
Added new row for Voltage Output Swing from Rail parameter to Output subsection of Electrical Characteristics ............ 3
•
Changed Voltage Output Swing from Rail parameter to over temperature in Output subsection of Electrical
Characteristics ...................................................................................................................................................................... 3
•
Updated format of thermal information tables ...................................................................................................................... 4
•
Added MSOP-8 package to OPA2171 Thermal Information table ....................................................................................... 4
•
Updated pinout configurations for OPA2171 and OPA4171 ................................................................................................ 5
•
Changed Figure 9 ................................................................................................................................................................. 8
Changes from Revision A (November, 2010) to Revision B
Page
•
Changed input offset voltage specification ........................................................................................................................... 3
•
Changed input offset voltage, over temperature specification .............................................................................................. 3
•
Changed quiescent current per amplifier, over temperature specification ........................................................................... 3
Copyright © 2010–2011, Texas Instruments Incorporated
15
PACKAGE OPTION ADDENDUM
www.ti.com
16-Aug-2012
PACKAGING INFORMATION
Orderable Device
(1)
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
OPA171AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA171AIDBVR
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA171AIDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA171AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA171AIDRLR
ACTIVE
SOT
DRL
5
4000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
OPA171AIDRLT
ACTIVE
SOT
DRL
5
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
OPA2171AID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA2171AIDCUR
ACTIVE
US8
DCU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
OPA2171AIDCUT
ACTIVE
US8
DCU
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
OPA2171AIDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA2171AIDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA2171AIDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA4171AID
ACTIVE
SOIC
D
14
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4171AIDR
ACTIVE
SOIC
D
14
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4171AIPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
OPA4171AIPWR
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
The marketing status values are defined as follows:
Addendum-Page 1
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
16-Aug-2012
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF OPA171 :
• Automotive: OPA171-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
OPA171AIDBVR
SOT-23
DBV
5
3000
180.0
OPA171AIDBVT
SOT-23
DBV
5
250
OPA171AIDR
SOIC
D
8
2500
OPA171AIDRLR
SOT
DRL
5
OPA171AIDRLT
SOT
DRL
OPA2171AIDCUR
US8
OPA2171AIDCUT
US8
OPA2171AIDGKR
B0
(mm)
K0
(mm)
P1
(mm)
8.4
3.23
3.17
1.37
4.0
180.0
8.4
3.23
3.17
1.37
330.0
12.4
6.4
5.2
2.1
4000
180.0
8.4
1.98
1.78
5
250
180.0
8.4
1.98
DCU
8
3000
180.0
8.4
DCU
8
250
180.0
8.4
VSSOP
DGK
8
2500
330.0
OPA2171AIDR
SOIC
D
8
2500
OPA4171AIDR
SOIC
D
14
2500
OPA4171AIPWR
TSSOP
PW
14
2000
W
Pin1
(mm) Quadrant
8.0
Q3
4.0
8.0
Q3
8.0
12.0
Q1
0.69
4.0
8.0
Q3
1.78
0.69
4.0
8.0
Q3
2.25
3.35
1.05
4.0
8.0
Q3
2.25
3.35
1.05
4.0
8.0
Q3
12.4
5.3
3.4
1.4
8.0
12.0
Q1
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Aug-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA171AIDBVR
SOT-23
DBV
5
3000
202.0
201.0
28.0
OPA171AIDBVT
SOT-23
DBV
5
250
202.0
201.0
28.0
OPA171AIDR
SOIC
D
8
2500
367.0
367.0
35.0
OPA171AIDRLR
SOT
DRL
5
4000
202.0
201.0
28.0
OPA171AIDRLT
SOT
DRL
5
250
202.0
201.0
28.0
OPA2171AIDCUR
US8
DCU
8
3000
202.0
201.0
28.0
OPA2171AIDCUT
US8
DCU
8
250
202.0
201.0
28.0
OPA2171AIDGKR
VSSOP
DGK
8
2500
366.0
364.0
50.0
OPA2171AIDR
SOIC
D
8
2500
367.0
367.0
35.0
OPA4171AIDR
SOIC
D
14
2500
367.0
367.0
38.0
OPA4171AIPWR
TSSOP
PW
14
2000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages