OPTEK OPB829DZ Slotted optical switch Datasheet

Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
Features:
•
•
•
•
•
OPB827
OPB828
0.125” (3.18 mm) wide, 0.215” (5.46 mm) deep slot
0.305” (7.75 mm) lead spacing (OPB827)
0.220” (5.59 mm) lead spacing (OPB828)
24-inch 26 AWG wire leads (OPB829)
Inexpensive plastic housing
Product Photo Here
OPB829Z
Description:
Each OPB827, OPB828 and OPB829 device consists of an infrared emitting diode (LED, 890 nm center
wavelength) and a NPN silicon phototransistor, mounted on opposite sides of a 0.125” (3.18 mm) wide slot in a
low-cost black plastic housing. A variety of aperture sizes are offered (see chart below). The OPB927 and
OPB828 are designed for PCBoard mounting with a minimum lead length of 0.35” (8.9 mm) while the OPB829Z
(wire version) has 24-inch 26 AWG wire leads. Phototransistor switching occurs when an opaque object passes
through the slot.
The OPB827 is offered with 0.305” (7.75 mm) and the OPB828 is offered with 0.220” (5.59 mm) lead spacing for
PCBoard mounting. The OPB829Z has 24” (61 cm) 26 AWG wire leads for remote mounting.
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for
more information.
Applications:
•
•
•
•
•
Non-contact object sensing
Assembly line automation
Machine automation
Equipment safety
Machine safety
Ordering Information
Part Number
Slot Width/
Depth
Housing
Aperture
Emitter/Sensor
Wire Lead
Length / Spacing
None
OPB827A
IR Transmissive
None / 0.01"
OPB827B
0.120" / 0.315”
0.425" / 0.300"
None / 0.06"
OPB827C
Opaque
None / 0.01"
OPB827D
None
OPB828A
IR Transmissive
None / 0.01"
OPB828B
0.120" / 0.315”
0.425" / 0.220"
None / 0.06"
OPB828C
Opaque
None / 0.01"
OPB828D
None
OPB829AZ
IR Transmissive
None / 0.01"
OPB829BZ
0.125” / 0.315”
24" / 26 AWG Wire
None / 0.06"
OPB829CZ
Opaque
OPB829DZ
None / 0.01"
CONTAINS POLYSULFONE
To avoid stress cracking, we suggest using
ND Industries’ Vibra-Tite for thread-locking.
Vibra-Tite evaporates fast without causing structural
failure in OPTEK’s molded plastics.
Applies to: OPB360, OPB370, OPB380, OPB390
and OPB860, OPB870, OPB880, OPB890.
RoHS
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2
09/06
Page 1 of 5
Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
OPB827 and OPB828 Series
OPB829Z Series
[ MILLIMETERS]
DIMENSIONS ARE IN:
INCHES
2
3
1
4
Color/Pin #
Description
Color/Pin #
Description
Black-2
Cathode
White-3
Collector
Red-1
Anode
Green-4
Emitter
Lead Spacing
OPB827 = 0.305”
OPB828 = 0.220”
OPB829 =
24” 26 AWG Wires
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.2 09/06
Page 2 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
Absolute Maximum Ratings (TA=25°C unless otherwise noted)
Storage and Operating Temperature
OPB827, OPB828
OPB829Z
-40° C to +85° C
-40° C to +80° C
Lead Soldering Temperature (1/16 inch [1.6 mm] from case for 5 seconds with soldering iron) (1)
260° C
Input Diode
Forward DC Current
50 mA
Peak Forward Current (1µs pulse width, 300 pps)
3A
Reverse DC Voltage
2V
(2)
100 mW
Power Dissipation
Output Phototransistor
Collector-Emitter Voltage
30 V
Emitter-Collector Voltage
5V
Collector DC Current
30 mA
Power Dissipation (2)
100 mW
Notes:
(1)
(2)
(3)
(4)
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 1.82 mW/° C above 25° C.
Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones.
All parameters were tested using pulse technique.
Electrical Characteristics (TA = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode (See OP240 for additional information—for reference only)
VF
Forward Voltage
-
-
1.7
V
IF = 20 mA
IR
Reverse Current
-
-
100
µA
VR = 2 V
Output Transistor (See OP550 for additional information—for reference only)
V(BR)CEO
Collector-Emitter Breakdown Voltage
30
-
-
V
IC = 1 mA
V(BR)ECO
Emitter-Collector Breakdown Voltage
5
-
-
V
IE = 100 µA
Collector-Emitter Dark Current
-
-
100
nA
VCE = 10 V, IF = 0, EE = 0
Saturation Voltage
-
-
0.6
V
IC = 1800 µA, IF = 20 mA
1800
-
-
µA
VCE = 0.6 V, IF = 20 mA
ICEO
Coupled
VCE(SAT)
IC(ON)
On-State Collector Current
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2
09/06
Page 3 of 5
Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
OPB827, OPB828, OPB829 Series - Devices A and C
OPB827 thru OPB829 (A, C) - Flag Next to
Sensor
1.20
1.20
1.00
1.00
Typical I C(ON) Response (mA)
Typical I C(ON) Response (mA)
OPB827 thru OPB829 (A, C) - Flag Next to
Emitter
0.80
0.60
0.40
0.20
Right to Left
Left to Right
Top to Bottom
0.05
0.60
0.40
Right to Left
Left to Right
0.20
Top to Bottom
0.00
0.00
0.80
0.10
0.15
0.20
0.25
0.00
0.00
0.05
Displacement Distance (inches)
0.10
0.15
0.20
0.25
Displacement Distance (inches)
OPB827 thru OPB829 (A, C) - Flag in Middle of
Slot
1.20
Typical I C(ON) Response (mA)
1.00
0.80
0.60
0.40
0.20
Right to Left
Left to Right
Top to Bottom
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.2 09/06
Page 4 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
OPB827, OPB828, OPB829 Series - Devices B and D
OPB827 thru OPB829 (B, D) - Flag Next to Sensor
1.20
1.00
1.00
Typical I C (ON) Response (mA)
Typical I C (ON) Response (mA)
OPB827 thru OPB829 (B, D) - Flag Next to Emitter
1.20
0.80
0.60
0.40
0.80
0.60
0.40
Right to Left
0.20
Left to Right
0.20
Top to Bottom
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
0.00
0.00
Right to Left
Left to Right
Top to Bottom
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
OPB827 thru OPB829 (B, D) - Flag Next to Sensor
1.20
0
Typical I C (ON) Response (mA)
1.00
Top to Bottom
0.80
Emitter
0.60
Left to Right
Right to Left
0.40
Sensor
0.20
Right to Left
Left to Right
0
Width
Top to Bottom
0.00
0.00
0.05
0.10
0.15
0.20
0.25
Displacement Distance (inches)
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue A.2
09/06
Page 5 of 5
Similar pages