PI3C34X461 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, BusSwitch Product Features Near zero propagation delay 5Ω switches connect inputs to outputs High Bandwidth (>200 MHz) Permits Hot Insertion Rail-to-Rail, 3.3V Switching 5V I/O Tolerant Package available: 96-pin Low Profile Fine Pitch Ball Grid Array (NB) Product Description Pericom Semiconductors PI3C series of logic circuits are produced using the Companys advanced submicron CMOS technology, achieving industry leading performance. The PI3C34X461 is a 40-bit, 2-port bus switch designed with a low ON resistance (5Ω) allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable (BE) input signal. Logic Block Diagram Product Pin Description 1A0 1A 9 1B0 2A0 1B9 2A9 2B9 2BE 1BE 3A0 3B0 4A0 4B0 3A 9 3B9 4A9 4B9 3BE Pin Name 2B0 De s cription NA0 - NA9 Bus A NB0 - NB9 Bus B NBE Bus Enable Pins (Active LOW) NGN D Ground NVCC Power Note: N = 1 through 4 for each set of 10-Bit Buses. 4BE Truth Table(1) Function Disconnect Connect Note 1: H = High Voltage Level L = Low Voltage Level Hi-Z = High Impedance NBE H L A09 Hi-Z B09 1 PS8432B 01/19/01 PI3C34X461 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Product Pinout by Name Name Ball Pad Name Ball Pad Name Ball Pad Name Ball Pad 1A0 A3 2A0 E3 3A0 J3 4A0 N3 1B0 A5 2B0 E5 3B0 J5 4B0 N5 1A1 A2 2A1 E2 3A1 J2 4A1 N2 1B1 A6 2B1 E6 3B1 J6 4B1 N6 1A2 A1 2A2 E1 3A2 J1 4A2 N1 1B2 B5 2B2 F5 3B2 K5 4B2 P5 1A3 B2 2A3 F2 3A3 K2 4A3 P2 1B3 B6 2B3 F6 3B3 K6 4B3 P6 1A4 B1 2A4 F1 3A4 K1 4A4 P1 1B4 C5 2B4 G5 3B4 L5 4B4 R5 1A5 C2 2A5 G2 3A5 L2 4A5 R2 1B5 C6 2B5 G6 3B5 L6 4B5 R6 1A6 C1 2A6 G1 3A6 L1 4A6 R1 1B6 D5 2B6 H5 3B6 M5 4B6 T5 1A7 D2 2A7 H2 3A7 M2 4A7 T2 1B7 D6 2B7 H6 3B7 M6 4B7 T6 1A8 D1 2A8 H1 3A8 MI 4A8 T1 1B8 D4 2B8 H4 3B8 M4 4B8 T4 1A9 D3 2A9 H3 3A9 M3 4A9 T3 1B9 C4 2B9 G4 3B9 L4 4B9 R4 NC B3 NC F3 NC K3 NC P3 1BE A4 2BE E4 3BE J4 4BE N4 1VCC B4 2VCC F4 3VCC K4 4VCC P4 1GN D C3 2GN D G3 3GN D L3 4GN D R3 2 PS8432B 01/19/01 PI3C34X461 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Product Pinout [LFBGA(N96) Package] 5 6 1BE 1B0 1B1 NC 1VCC 1B2 1B3 1A5 1GN D 1B9 1B4 1B5 1A8 1A7 1A9 1B8 1B6 1B7 E 2A2 2A1 2A0 2BE 2B0 2B1 F 2A4 2A3 NC 2VCC 2B2 2B3 G 2A6 2A5 2GN D 2B9 2B4 2B5 H 2A8 2A7 2A9 2B8 2B6 2B7 J 3A2 3A1 3A0 3BE 3B0 3B1 K 3A4 3A3 NC 3VCC 3B2 3B3 L 3A6 3A5 3GN D 3B9 3B4 3B5 M 3A8 3A7 3A9 3B8 3B6 3B7 N 4A2 4A1 4A0 4BE 4B0 4B1 P 4A4 4A3 NC 4VCC 4B2 4B3 R 4A6 4A5 4GN D 4B9 4B4 4B5 T 4A8 4A7 4A9 4B8 4B6 4B7 1 2 3 4 A 1A2 1A1 1A0 B 1A4 1A3 C 1A6 D 1 2 3 4 5 6 7 8 9 10 11 12 Product Pin Assignment (Top View) 13 14 15 3 PS8432B 01/19/01 PI3C34X461 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ............................................................ 65°C to +150°C Ambient Temperature with Power Applied ........................... 40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only) .... 0.5V to +4.6V Supply Voltage to Ground Potential (Outputs & D/O Only) . 0.5V to +4.6V DC Input Voltage ................................................................... 0.5V to +4.6V DC Output Current ............................................................................... 120mA Power Dissipation .................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 3.3V ±10%) Parameters Description Test Conditions(1) Min. Typ(2) Max. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 VIL Input LOW Voltage Guaranteed Logic LOW Level 0.5 IIH Input HIGH Current VCC = Max., VIN = VCC ±1 IIL Input LOW Current VCC = Max., VIN = GND ±1 IOZH High Impedance Output Current 0 ≤ A, B ≤ VCC ±1 VIK Clamp Diode Voltage VCC = Min., IIN = 18mA RON Switch On Resistance (4) VCC = Min., VIN = 0.0V, ION = 48mA VCC = Min., VIN = 2.4V, ION = 15mA Units V 0.8 µA 0.73 1.2 V 5 10 7 15 Ω Capacitance (TA = 25°C, f = 1 MHz) Parame te rs (5) De s cription Te s t Conditions Typ. CIN Input Capacitance VIN = 0V 3.5 C O FF A/B Capacitance, Switch Off VIN = 0V 5.0 CON A/B Capacitance, Switch On VIN = 0V 10.0 Units pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested. 4 PS8432B 01/19/01 PI3C34X461 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Test Conditions(1) Parameters Description ICC Quiescent Power Supply Current VCC = Max. VIN = GND or VCC ∆ICC Supply Current per Input @ TTL HIGH VCC = Max. VIN = 3.0V(3) Min. Typ(2) Max. 260 500 750 Units 1 µA 2 Notes: 1. For Max. or Min.conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25°C ambient. 3. Per TTL driven input (control input only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. 3 Switching Characteristics over Operating Range 5 4 PI3C34X461 Com. Parame te rs De s cription Conditions M in. M ax. Units 6 ns 7 (2,3) tPLH tPHL Propagation Delay Ax to Bx, Bx to Ax tPZH tPZL Bus Enable Time BE to Ax or Bx tPHZ tPLZ Bus Disable Time BE to Ax or Bx 0.25 CL = 50pF, RL = 500Ω 1.5 6.5 1.5 5.5 8 Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 9 10 11 12 13 14 15 5 PS8432B 01/19/01 PI3C34X461 3.3V, High Bandwidth, Hot Insertion, 40-Bit, 2-Port, Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 96-Pin LFBGA (NB) Package Pin 1 Pin 1 FIDUCIAL MARK 5.50 ± 0.15 // 0.10 C FIDUCIAL MARK SEATING PLANE 0.10 C A 6 5 4 3 2 1 A B C C D E F 13.50 ± 0.15 0.80 G H J K L M N P R T 0.75 0.40 ± 0.05 0.75 0.85 Min. 1.40 Max. B 96 x φ0.40 ± 0.07 0.20 s C A s 0.08 s C B s Ordering Information Part Pin - Package Dime ns ions Ball Pitch PI5C34X461NB 96 - LFBGA (NB) 5.5mm x 13.5mm 0.8mm Applications Information Logic Inputs The logic control inputs can be driven up to +3.6V regardless of the supply voltage. For example, given a +3.3V supply, the output enables or select pins may be driven LOW to 0V and HIGH to 3.6V. Driving IN Rail-to-Rail® minimizes power consumption. Power Supply Sequencing Proper power-supply sequencing is advised for all CMOS devices. It is recommended to always apply VCC before applying signals to the input/output or control pins. Pericom Semiconductor Corporation 2380 Bering Drive San Jose, CA 95131 1-800-435-2336 Fax (408) 435-1100 http://www.pericom.com 6 PS8432B 01/19/01