TI QFN-24

THS6204
®
TH
S6
204
TH
S6
®
20
4
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
Dual-Port, Differential VDSL2 Line Driver Amplifiers
FEATURES
1
• Low Power Consumption:
– 21mA/Port Full Bias Mode
– 16.2mA/Port Mid Bias Mode
– 11.2mA/Port Low Bias Mode
– Low-Power Shutdown Mode
– IADJ Pin for Variable Bias
• Low Noise:
– 2.5nV/√Hz Voltage Noise
– 17pA/√Hz Inverting Current Noise
– 1.2pA/√Hz Noninverting Current Noise
• Low MTPR Distortion:
– 70dB with +20.5dBm G.993.2—Profile 8b
• –89dBc HD3 (1MHz, 100Ω Differential)
• High Output Current: > 424mA (25Ω Load)
• Wide Output Swing: 43.2VPP (±12V, 100Ω
Differential)
• Wide Bandwidth: 150MHz (Gain = 10V/V)
• Port-To-Port Separation of 90dB at 1MHz
• PSRR of 50dB at 1MHz for Good Isolation
• Wide Power-Supply Range: 10V to 28V
23
APPLICATIONS
•
•
Ideal For VDSL2 Systems
Backward-Compatible with
ADSL/ADSL2+/ADSL2++ Systems
DESCRIPTION
The THS6204 is a dual-port, current-feedback
architecture, differential line driver amplifier system
ideal for xDSL systems. The device is targeted for
use in VDSL2 (very-high-bit-rate digital subscriber
line 2) line driver systems that enable greater than
+20.5dBm line power up to 8.5MHz with good
linearity supporting the G.993.2 VDSL2 8b profile. It
is also fast enough to support central-office
transmission of +14.5dBm line power up to
18.1MHz—Profile 30a.
The unique architecture of the THS6204 allows
quiescent current to be minimal while still achieving
very high linearity. Differential distortion, under full
bias conditions, is –89dBc at 1MHz and reduces to
only –73dBc at 10MHz. Fixed multiple bias settings of
the amplifiers allows for enhanced power savings for
line lengths where the full performance of the
amplifier is not required. To allow for even more
flexibility and power savings, an IADJ pin is available
to further lower the bias currents.
The wide output swing of 43.2VPP (100Ω
differentially) with ±12V power supplies, coupled with
over 425mA current drive (25Ω), allows for wide
dynamic headroom, keeping distortion minimal.
The THS6204 is available in a QFN-24 or a
TSSOP-24 PowerPAD™ package.
+12V
CODEC
VIN+
9.1W
2kW
2.74kW
1:1.1
+20.5dBm
Line Power
100W
1.33kW
2.74kW
2kW
9.1W
CODEC
VIN-12V
Figure 1. Typical VDSL2 Line Driver Circuit
Utilizing One Port of the THS6204
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments, Incorporated.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2009, Texas Instruments Incorporated
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
PRODUCT (2)
PACKAGE-LEAD
PACKAGE
DESIGNATOR
PACKAGE MARKING
QFN-24
RHF
6204
TSSOP-24
PWP
THS6204
THS6204IRHFT
THS6204IRHFR
THS6204IPWP
THS6204IPWPR
(1)
(2)
TRANSPORT MEDIA, QUANTITY
Tape and Reel, 250
Tape and Reel, 3000
Rails, 60
Tape and Reel, 2000
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
The PowerPAD is electrically isolated from all other pins.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
THS6204
UNIT
Supply voltage, VS– to VS+
28
V
Input voltage, VI
±VS
Differential input voltage, VID
Output current, IO—static dc (2)
Continuous power dissipation
Maximum junction temperature, any condition, TJ
±2
V
±100
mA
See Dissipation Ratings table
(3)
+150
°C
Maximum junction temperature, continuous operation, long-term reliability, TJ (4), QFN
package
+130
°C
Maximum junction temperature, continuous operation, long-term reliability, TJ (4), TSSOP
package
+140
°C
–65 to +150
°C
+300
°C
Human body model (HBM)
2000
V
Charged device model (CDM)
500
V
Machine model (MM)
100
V
Storage temperature range, TSTG
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
ESD ratings
(1)
(2)
(3)
(4)
2
Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute maximum rated conditions for extended periods may degrade device reliability.
The THS6204 incorporates a PowerPAD on the underside of the chip. This acts as a heatsink and must be connected to a thermally
dissipating plane for proper power dissipation. Failure to do so may result in exceeding the maximum junction temperature which could
permanently damage the device. See TI Technical Brief SLMA002 for more information about utilizing the PowerPAD
thermally-enhanced package. Under high-frequency ac operation (> 10kHz), the short-term output current capability is much greater
than the continuous dc output current rating. This short-term output current rating is about 8.5X the dc capability, or about ±850mA.
The absolute maximum junction temperature under any condition is limited by the constraints of the silicon process.
The absolute maximum junction temperature for continuous operation is limited by the package constraints. Operation above this
temperature may result in reduced reliability and/or lifetime of the device.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
DISSIPATION RATINGS
POWER RATING (3)
(TJ = +130°C)
(1)
(2)
(3)
PACKAGE
θJC (°C/W)
θJA (°C/W) (1) (2)
TA = +25°C
TA = +85°C
QFN-24 (RHF)
1.7
32
3.28W
1.4W
HTSSOP-24 (PWP)
0.92
31
3.39W
1.45W
This data was taken using a 4-layer, 3in × 3in (76.2mm × 76.2mm) test PCB with the PowerPAD soldered to the PCB. If the PowerPAD
is not soldered to the PCB, θJA increases to +74°C/W for the RHF package and +62°C/W for the PWP package.
For high-power dissipation applications, soldering the PowerPAD to the PCB is required. Failure to do so may result in reduced reliability
and/or lifetime of the device. See TI technical brief SLMA002 for more information about utilizing the PowerPAD thermally enhanced
package.
Power rating is determined with a junction temperature of +130°C. This is the point where distortion starts to substantially increase and
long-term reliability starts to be reduced. Thermal management of the final PCB should strive to keep the junction temperature at or
below +130°C for best performance and reliability.
RECOMMENDED OPERATING CONDITIONS
THS6204
MIN
MAX
UNIT
Dual supply
±5
±14
V
Single supply
10
28
V
Operating free-air temperature, TA
–40
+85
°C
Operating junction temperature, continuous operating temperature, TJ, QFN package
–40
+130
°C
Operating junction temperature, continuous operating temperature, TJ, TSSOP package
–40
+140
°C
Normal storage temperature, TSTG
–40
+85
°C
Supply voltage, VS– to VS+
PIN CONFIGURATIONS(1)(2)(3)
QFN-24(4)
RHF PACKAGE
(TOP VIEW)
D1 IN+
BIAS-2/
D1D2
BIAS-1/
D1D2
VS-
VS+
D1 OUT
VS-
24
23
22
21
20
HTSSOP-24(4)
PWP PACKAGE
(TOP VIEW)
BIAS-1/D1D2
19
1
2
18
D2 IN-
GND
3
17
D2 OUT
4
16
NC
(4)
5
15
D3 OUT
D3 IN+
6
14
D3 IN-
D1 OUT
BIAS-2/D1D2
3
22
D1 IN-
D1 IN+
4
21
D2 IN-
D2 IN+
5
20
D2 OUT
GND
6
19
NC
(4)
PowerPAD
NC
D3 IN+
8
17
D3 OUT
D4 IN+
9
16
D3 IN-
BIAS-2/D3D4
10
15
D4 IN-
12
(4)
18
BIAS-1/D3D4
11
14
D4 OUT
D4 OUT
11
VS+
10
VS-
9
BIAS-1/
D3D4
23
7
VS-
12
13
VS+
13
BIAS-2/
D3D4
2
IADJ
7
8
D4 IN+
VS+
(4)
IADJ
PowerPAD
24
D1 IN-
D2 IN+
NC
1
D4 IN-
(1)
The PowerPAD is electrically isolated from all other pins and can be connected to any potential voltage range from
VS– to VS+. Typically, the PowerPAD is connected to the GND plane as this plane tends to physically be the largest
and is able to dissipate the most amount of heat.
(2)
The THS6204 defaults to shutdown mode if no signal is present on the bias pins.
(3)
The GND pin range is from VS– to (VS+ – 5V).
(4)
NC = no connection.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
3
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±12V
At TA = +25°C, RF = 1.24kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
UNITS
MIN/
MAX
TEST
LEVEL (1)
MHz
Typ
C
MHz
Min
B
114
MHz
Typ
C
GDIFF = 10V/V differential,
VO = 20VPP
120
MHz
Typ
C
GDIFF = 10V/V, VO = 20V step,
differential
3800
V/µs
Min
B
GDIFF = +5V/V, VO = 2VPP, differential
5
ns
Typ
C
PARAMETER
CONDITIONS
+25°C
GDIFF = 5V/V differential, RF = 1.5kΩ,
VO = 2VPP
160
GDIFF = 10V/V differential,
RF = 1.24kΩ, VO = 2VPP
150
0.1dB bandwidth flatness
GDIFF = 10V/V differential,
RF = 1.24kΩ
Large-signal bandwidth
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
AC PERFORMANCE
Small-signal bandwidth,
–3dB (VO = 2VPP)
Slew rate (10% to 90% level)
Rise and fall time
120
3200
110
3100
100
3000
Harmonic distortion
2nd harmonic
3rd harmonic
GDIFF = 10V/V,
VO = 2VPP,
f = 1MHz, RL = 100Ω
2nd harmonic
3rd harmonic
GDIFF = 10V/V,
VO = 2VPP,
f = 10MHz,
RL = 100Ω
Full bias
–100
Low bias
–96
Full bias
–89
Low bias
–85
–95
–85
–70
–92
–82
–80
Min
B
dBc
Typ
C
dBc
Min
B
dBc
Typ
C
Full bias
–75
–72
Full bias
–73
dBc
Min
B
Low bias
–58
dBc
Typ
C
–61
–65
dBc
Low bias
–65
–68
–90
–53
dBc
Min
B
dBc
Typ
C
VDSL2 8b profile +20.5dBm
–70
dBc
Typ
C
VDSL2 17a profile +14.5dBm;
power supply = ±7.5V
–65
dBc
Typ
C
Differential input voltage noise
f = 1MHz
2.5
3.0
3.2
3.3
nV/√Hz
Max
B
Differential inverting current noise
f = 1MHz
17
20
22
24
pA/√Hz
Max
B
Differential noninverting current noise
f = 1MHz
1.2
1.4
1.5
1.6
pA/√Hz
Max
B
RL = 100Ω
700
330
320
300
kΩ
Typ
A
±15
±50
±55
±60
mV
Max
A
±110
±155
µV/°C
Max
B
Multi-tone power ratio (MTPR)
G ≈ 11, active termination, SF ≈ 4.
DC PERFORMANCE
Open-loop transimpedance gain
Input offset voltage
Input offset voltage drift
Input offset voltage matching
Channels 1 to 2 and 3 to 4 only
Noninverting input bias current
±0.5
±5
±6
±7
mV
Max
A
±1
±3
±4
±5
µA
Max
A
±25
±30
nA/°C
Max
B
±45
±50
µA
Max
A
±115
±135
nA/°C
Max
B
µA
Max
A
A
Noninverting input bias current drift
Inverting input bias current
±8
±40
Inverting input bias current drift
Inverting input bias current matching
±8
±25
±30
±35
INPUT CHARACTERISTICS
Common-mode input range
Each amplifier
±9.5
±9
±8.8
±8.6
V
Min
Common-mode rejection ratio
Each amplifier
65
53
50
49
dB
Min
A
500 || 2
kΩ || pF
Typ
C
50
Ω
Typ
C
Noninverting input resistance
Inverting input resistance
(1)
(2)
(3)
4
Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value only for information.
Junction temperature = ambient for +25°C tested specifications.
Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over
temperature specifications.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
ELECTRICAL CHARACTERISTICS: VS = ±12V (continued)
At TA = +25°C, RF = 1.24kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
±10.8
±10.6
±10.5
±10.4
RL = 25Ω, each output, linear output
±10.4
±10.2
±10.1
RL = 25Ω, each output
±416
±408
±404
PARAMETER
UNITS
MIN/
MAX
TEST
LEVEL (1)
V
Typ
C
V
Min
A
±10.0
V
Min
A
±400
mA
Min
A
±1
A
Typ
C
0.2
Ω
Typ
C
–90
dB
Typ
C
CONDITIONS
+25°C
RL = 100Ω, each output, linear output
±10.9
RL = 50Ω, each output, linear output
OUTPUT CHARACTERISTICS (4)
Output voltage swing
Output current (sourcing, sinking)
Short-circuit output current
Output impedance
Crosstalk
f = 1MHz, differential
f = 1MHz,
VOUT = 2VPP
Port 1 to
port 2
POWER SUPPLY
Operating voltage
V
Typ
C
Maximum operating voltage
±14
±14
±14
V
Max
A
Minimum operating voltage
±5
±5
±5
V
Min
B
Maximum IS+ quiescent current
Minimum IS+ quiescent current
Maximum IS– quiescent current
Minimum IS– quiescent current
±12
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
21
22.5
23.5
24
mA
Max
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
16.2
17.7
18.5
19
mA
Max
A
Per port, mid bias ; RADJ = 604Ω
12.6
14.1
15
15.5
mA
Max
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
11.2
12.7
13.4
13.9
mA
Max
A
Per port, bias off
(Bias-1 = 1, Bias-2 = 1)
0.5
0.8
0.9
1
mA
Max
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
21
19.5
18.5
17
mA
Min
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
16.2
14.7
13.7
13
mA
Min
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
11.2
9.7
9.1
7.6
mA
Min
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
20.5
21.5
22.5
23
mA
Max
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
15.7
16.7
17.4
17.8
mA
Max
A
Per port, mid bias ; RADJ = 604Ω
12.1
13.1
14
14.5
mA
Max
A
Per port, low bias
(Bias-1 = 0,Bias-2 = 1)
10.7
11.7
12.1
12.4
mA
Max
A
Per port, bias off
(Bias-1 = 1, Bias-2 = 1)
0.1
0.3
0.6
0.8
mA
Max
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
20.5
19.5
18.5
17.5
mA
Min
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
15.7
14.7
13.8
13.6
mA
Min
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
10.7
9.7
9.4
9.1
mA
Min
A
Current through GND pin
0.5
mA
Typ
C
Power-supply rejection ratio (+PSRR)
66
54
53
52
dB
Min
A
Power-supply rejection ratio (–PSRR)
65
52
51
50
dB
Min
A
(4)
Test circuit is shown in Figure 2.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
5
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±12V (continued)
At TA = +25°C, RF = 1.24kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
UNITS
Logic 1, with respect to GND (5)
1.9
1.9
1.9
Logic 0, with respect to GND (5)
0.8
0.8
0.8
PARAMETER
CONDITIONS
+25°C
MIN/
MAX
TEST
LEVEL (1)
V
Min
B
V
Max
B
A
LOGIC
Bias control pin logic threshold
Bias pin quiescent current
Turn-on time delay (tON)
Turn-off time delay (tOFF)
Bias-X = 0.5V (logic 0)
20
30
33
35
µA
Max
Bias-X = 3.3V (logic 1)
0.3
1
1.1
1.2
µA
Max
A
Time for IS to reach 50%
of final value
1
µs
Typ
C
Bias pin input impedance
Amplifier output impedance
(5)
Off bias (Bias-1 = 1, Bias-2 = 1)
1
µs
Typ
C
50
kΩ
Typ
C
10 || 5
kΩ || pF
Typ
C
The GND pin usable range is from VS– to (VS+ – 5V).
Table 1. Logic Table
6
BIAS-1
BIAS-2
FUNCTION
DESCRIPTION
0
0
Full bias mode
Amplifiers on with lowest distortion possible
1
0
Mid bias mode
Amplifiers on with power savings and a reduction in distortion performance
0
1
Low bias mode
Amplifiers on with enhanced power savings and a reduction of performance
1
1
Shutdown mode
Amplifiers off and output has high impedance (default state if left floating)
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
ELECTRICAL CHARACTERISTICS: VS = ±6V
At TA = +25°C, RF = 1.5kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
UNITS
MIN/
MAX
TEST
LEVEL (1)
MHz
Typ
C
MHz
Min
B
12
MHz
Typ
C
G = 10V/V differential, VO = 20VPP
140
MHz
Typ
C
G = 10V/V, VO = 20V step,
differential
1600
V/µs
Min
B
G = +5V/V, VO = 2VPP, differential
5
ns
Typ
C
PARAMETER
CONDITIONS
+25°C
Small-signal bandwidth,
–3dB (VO = 2VPP)
G = 5V/V differential, RF = 1.82kΩ
140
G = 10V/V differential, RF = 1.5kΩ
140
0.1dB bandwidth flatness
G = 10V/V differential, RF = 1.5kΩ
Large-signal bandwidth
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
110
100
95
AC PERFORMANCE
Slew rate (10% to 90% level)
Rise and fall time
1200
1100
1000
Harmonic distortion
2nd harmonic
3rd harmonic
2nd harmonic
3rd harmonic
G = 10V/V,
VO = 2VPP,
f = 1MHz,
RL = 100Ω differential
G = 10V/V,
VO = 2VPP,
f = 10MHz,
RL = 100Ω differential
Full bias
–98
Low bias
–93
Full bias
–93
Low bias
–89
–92
–84
–75
–89
–81
–79
Min
B
dBc
Typ
C
dBc
Min
B
dBc
Typ
C
Full bias
–80
–74
Full bias
–66
dBc
Min
B
Low bias
–55
dBc
Typ
C
–58
–68
dBc
Low bias
–60
–70
–87
–54
dBc
Min
B
dBc
Typ
C
VDSL2 8b profile +20.5dBm
–70
dBc
Typ
C
VDSL2 17a profile +14.5dBm;
power supply = ±7.5V
–65
dBc
Typ
C
Differential input voltage noise
f = 1MHz
2.5
3.0
3.2
3.3
nV/√Hz
Max
B
Differential inverting current noise
f = 1MHz
17
20
22
24
pA/√Hz
Max
B
Differential noninverting current noise
f = 1MHz
1.2
1.4
1.5
1.6
pA/√Hz
Max
B
RL = 100Ω
650
330
320
300
kΩ
Typ
A
±10
±45
±50
±55
mV
Max
A
±110
±155
µV/°C
Max
B
Multi-tone power ratio (MTPR)
G ≈ 11, active termination, SF ≈ 4.
DC PERFORMANCE
Open-loop transimpedance gain
Input offset voltage
Input offset voltage drift
Input offset voltage matching
Channels 1 to 2 and 3 to 4 only
Noninverting input bias current
±0.5
±5
±6
±7
mV
Max
A
±1
±3
±4
±5
µA
Max
A
±25
±30
nA/°C
Max
B
±45
±50
µA
Max
A
±115
±135
nA/°C
Max
B
µA
Max
A
A
Noninverting input bias current drift
Inverting input bias current
±8
±40
Inverting input bias current drift
Inverting input bias current matching
±8
±25
±30
±35
INPUT CHARACTERISTICS
Common-mode input range
Each amplifier
±3.0
±2.9
±2.8
±2.7
V
Min
Common-mode rejection ratio
Each amplifier
62
51
48
47
dB
Min
A
500 || 2
kΩ || pF
Typ
C
55
Ω
Typ
C
Noninverting input resistance
Inverting input resistance
(1)
(2)
(3)
Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value only for information.
Junction temperature = ambient for +25°C tested specifications.
Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over
temperature specifications.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
7
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±6V (continued)
At TA = +25°C, RF = 1.5kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
±4.9
±4.75
±4.65
±4.6
RL = 25Ω, each output, linear output
±4.7
±4.55
±4.45
RL = 25Ω, each output
±188
±182
±178
PARAMETER
UNITS
MIN/
MAX
TEST
LEVEL (1)
V
Typ
C
V
Min
A
±4.4
V
Min
A
±176
mA
Min
A
±1
A
Typ
C
0.2
Ω
Typ
C
–90
dB
Typ
C
CONDITIONS
+25°C
RL = 100Ω, each output, linear output
±4.9
RL = 50Ω, each output, linear output
OUTPUT CHARACTERISTICS (4)
Output voltage swing
Output current (sourcing, sinking)
Short-circuit output current
Output impedance
f = 1MHz, differential
f = 1MHz,
VOUT = 2VPP
Crosstalk
Port 1 to
port 2
POWER SUPPLY
Operating voltage
V
Typ
C
Maximum operating voltage
±14
±14
±14
V
Max
A
Minimum operating voltage
±5
±5
±5
V
Min
B
Maximum IS+ quiescent current
Minimum IS+ quiescent current
Maximum IS– quiescent current
Minimum IS– quiescent current
±6
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
17
21
21.5
22
mA
Max
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
13.2
16.8
16.9
17
mA
Max
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
9.4
12.2
12.3
12.4
mA
Max
A
Per port, bias off
(Bias-1 = 1, Bias-2 = 1)
0.5
0.8
0.9
0.9
mA
Max
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
17
13
11.5
10
mA
Min
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
13.2
9.8
9.3
8.9
mA
Min
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
9.4
6.7
6.4
6.0
mA
Min
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
16.5
20.5
21
21.5
mA
Max
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
12.7
16.3
16.4
16.5
mA
Max
A
Per port, low bias
(Bias-1 = 0,Bias-2 = 1)
8.9
11.7
11.8
11.9
mA
Max
A
Per port, bias off
(Bias-1 = 1, Bias-2 = 1)
0.1
0.3
0.4
0.5
mA
Max
A
Per port, full bias
(Bias-1 = 0, Bias-2 = 0)
16.5
12.5
11
9.5
mA
Min
A
Per port, mid bias
(Bias-1 = 1, Bias-2 = 0)
12.7
9.3
8.8
8.4
mA
Min
A
Per port, low bias
(Bias-1 = 0, Bias-2 = 1)
8.9
6.2
5.9
5.5
mA
Min
A
Current through GND pin
0.5
mA
Typ
C
Power-supply rejection ratio (+PSRR)
64
54
53
52
dB
Min
A
Power-supply rejection ratio (–PSRR)
63
52
51
50
dB
Min
A
(4)
8
Test circuit is shown in Figure 2.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
ELECTRICAL CHARACTERISTICS: VS = ±6V (continued)
At TA = +25°C, RF = 1.5kΩ, RL = 100Ω differential, GDiff = 10V/V differential, GCM = 1V/V common-mode, and full bias, unless
otherwise noted. Each port is independently tested.
THS6204IRHF, IPWP
TYP
OVER TEMPERATURE
–40°C to
+85°C (3)
UNITS
Logic 1, with respect to GND (5)
1.9
Logic 0, with respect to GND (5)
0.8
PARAMETER
CONDITIONS
+25°C
+25°C (2)
0°C to
+70°C (3)
MIN/
MAX
TEST
LEVEL (1)
V
Min
B
V
Max
B
A
LOGIC
Bias control pin logic threshold
Bias pin quiescent current
Turn-on time delay (tON)
Turn-off time delay (tOFF)
Bias-X = 0.5V (logic 0)
20
30
33
35
µA
Max
Bias-X = 3.3V (logic 1)
0.3
1
1.1
1.2
µA
Max
A
Time for IS to reach 50%
of final value
1
µs
Typ
C
Bias pin input impedance
Amplifier output impedance
(5)
Off bias (Bias-1 = 1, Bias-2 = 1)
1
µs
Typ
C
50
kΩ
Typ
C
10 || 5
kΩ || pF
Typ
C
The GND pin usable range is from VS– to (VS+ – 5V).
Table 2. Logic Table
BIAS-1
BIAS-2
FUNCTION
DESCRIPTION
0
0
Full bias mode
Amplifiers on with lowest distortion possible
1
0
Mid bias mode
Amplifiers on with power savings and a reduction in distortion performance
0
1
Low bias mode
Amplifiers on with enhanced power savings and a reduction of performance
1
1
Shutdown mode
Amplifiers off and output has high impedance (default state if left floating)
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
9
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±12V, Full Bias
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
SMALL-SIGNAL FREQUENCY RESPONSE
vs BIAS MODE
SMALL-SIGNAL FREQUENCY RESPONSE
3
3
GDIFF = 5V/V
RF = 1.5kW
0
Normalized Gain (dB)
Normalized Gain (dB)
0
-3
-6
GDIFF = 10V/V
RF = 1.24kW
-9
GCM = 1V/V
VO = 2VPP
RADJ = 0W
RL = 100W
-12
-15
-18
Full Bias
-3
-6
75% Bias
-9
-12
-15
-18
10
100
400
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RADJ = 0W
RL = 100W
50% Bias
10
100
Frequency (MHz)
Frequency (MHz)
Figure 2.
Figure 3.
LARGE SIGNAL FREQUENCY RESPONSE
SMALL-SIGNAL AND LARGE-SIGNAL
PULSE RESPONSE
12
3
Large-Signal Pulse Response
(±10VP) Left Scale
Output Voltage (V)
-3
-6
VO = 20VPP
-9
GDIFF = 10V/V
GCM = 1V/V
RADJ = 0W
RL = 100W
-12
-15
VO = 8VPP
4
0.8
0.4
Small-Signal ±500mVP
Right Scale
0
0
-4
-0.4
-8
-0.8
-12
-18
0
60
120
180
240
Output Voltage (V)
Normalized Gain (dB)
8
VO = 2VPP
1.2
GDIFF = 10V/V
GCM = 1V/V
RL = 100W
RF = 1.2kW
VO = 4VPP
0
300
-1.2
Time (10ns/div)
300
Frequency (MHz)
Figure 4.
Figure 5.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
23
100
RS Optimized for 100% Bias
22pF
20
470pF
17
Gain (dB)
RS (W)
100pF
10
14
THS6204
10
100
10
1000
CL
VIN
5
1
47pF
11
8
1
39pF
RS
1kW
VOUT
Optional
RS
THS6204
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 6.
Figure 7.
Submit Documentation Feedback
300M
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±12V, Full Bias (continued)
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-60
-60
-70
-75
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
GDIFF = 10V/V
GCM = 1V/V
RL = 100W
f = 1MHz
3rd Harmonic
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-65
2nd Harmonic
-80
-85
-90
-95
-100
-70
-80
3rd Harmonic
-90
-100
-105
2nd Harmonic
-110
-110
400k
10M
1M
0.5
40M
1
10
Figure 8.
Figure 9.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
-75
Harmonic Distortion (dBc)
HARMONIC DISTORTION vs LOAD RESISTANCE
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-80
-85
3rd Harmonic
-90
-95
2nd Harmonic
-65
Harmonic Distortion (dBc)
-70
-100
-105
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-75
-85
3rd Harmonic
-95
-105
2nd Harmonic
-115
-125
4
5
6
7
8
9
10
11
12
50
100
Supply Voltage (±VS)
1k
Resistance (W)
Figure 10.
Figure 11.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ORDER INTERMODULATION INTERCEPT
55
-65
50
-75
3rd Harmonic
Intercept Point (dBm)
Harmonic Distortion (dBc)
20
Output Voltage (VPP)
Frequency (Hz)
-85
-95
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-105
-115
2nd Harmonic
45
40
35
30
25
GDIFF = 10V/V
GCM = 1V/V
20
-125
15
1
10
30
0
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 12.
Figure 13.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
11
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±12V, Full Bias (continued)
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
INPUT VOLTAGE AND
CURRENT NOISE DENSITY
OUTPUT VOLTAGE AND CURRENT LIMITATIONS
Output Voltage (V)
Output Voltage Noise Density (nV/ÖHz)
Input Current Noise Density (pA/ÖHz)
1000
12
10 GDIFF = 10V/V
8 GCM = 1V/V
6
4
2
0
-2
1W Internal
-4
Power Dissipation
-6
-8
-10
-12
-14
-200
-600
-400
1W Internal
Power Dissipation
50W Load Line
100W Load Line
Voltage and current noise contributing to differential noise.
100
Inverting Current Noise
(17.4pA/ÖHz)
Voltage Noise
(2.5nV/ÖHz)
10
1
0
200
400
600
1k
100
10k
Output Current (mA)
100k
1M
10M
Frequency (Hz)
Figure 14.
Figure 15.
SUPPLY CURRENT FOR FULL BIAS SETTINGS vs RADJ
PSRR vs FREQUENCY
25
Power-Supply Rejection Ratio (dB)
60
20
±IQ (mA)
Noninverting Current Noise
(1.2pV/ÖHz)
15
+IQ
10
-IQ
5
-PSRR
50
+PSRR
40
30
20
10
0
0
0
1
2
3
4
5
6
1k
10k
100k
1M
RADJ (kW)
Frequency (Hz)
Figure 16.
Figure 17.
OPEN-LOOP GAIN AND PHASE
10M
100M
CLOSED-LOOP OUTPUT IMPEDANCE
140
10
0
100
-90
Phase
80
-135
60
-180
40
-225
20
GDIFF = 10V/V
GCM = 1V/V
-315
100k
1
0.1
0.01
-270
0
10k
Output Impedance (W)
-45
Transimpedance Phase (°)
Transimpedance Gain (dBW)
Gain
120
1M
10M
100M
1G
0.001
100k
Frequency (Hz)
10M
100M
Frequency (Hz)
Figure 18.
12
1M
Figure 19.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±12V, 75% Bias
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
SMALL-SIGNAL FREQUENCY RESPONSE
LARGE-SIGNAL FREQUENCY RESPONSE
3
3
GDIFF = 5V/V
RF = 1.5kW
VO = 2VPP
0
Normalized Gain (dB)
Normalized Gain (dB)
0
-3
GDIFF = 10V/V
RF = 1.24kW
-6
-9
-12
GCM = 1V/V
VO = 2VPP
RL = 100W
-15
-18
-3
-6
VO = 20VPP
VO = 4VPP
-9
-12
GCM = 1V/V
GDIFF = 10V/V
RL = 100W
-15
VO = 8VPP
-18
10
100
0
300
20 40 60 80 100 120 140 160 180 200 220 240 260
Frequency (MHz)
Frequency (MHz)
Figure 20.
Figure 21.
DIFFERENTIAL SMALL-SIGNAL AND
LARGE-SIGNAL PULSE RESPONSE
SUPPLY CURRENT FOR FULL BIAS SETTINGS vs RADJ
12
1.2
8
0.8
4
0.4
18
16
0
Small-Signal ±500mVP
Right Scale
-4
-0.4
Large-Signal Pulse Response
(±10VP) Left Scale
-8
12
±IQ (mA)
0
Output Voltage (V)
Output Voltage (V)
14
10
8
+IQ
6
-IQ
4
-0.8
2
-12
-1.2
0
0
Time (10ns/div)
1
2
3
4
5
6
RADJ (kW)
Figure 22.
Figure 23.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
23
100
RS Optimized for 100% Bias
22pF
20
470pF
17
Gain (dB)
RS (W)
100pF
10
14
THS6204
100
10
1000
CL
VIN
5
1
47pF
11
8
1
39pF
RS
1kW
VOUT
Optional
RS
THS6204
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 24.
Figure 25.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
300M
13
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±12V, 75% Bias (continued)
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-60
-40
-60
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
GDIFF = 10V/V
GCM = 1V/V
RL = 100W
f = 1MHz
-65
-70
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
3rd Harmonic
-80
-90
2nd Harmonic
-100
-110
-70
-75
3rd Harmonic
-80
-85
-90
2nd Harmonic
-95
-100
-105
-120
100k
-110
10M
1M
0
30M
4
2
6
Figure 26.
10
12
14
16
Figure 27.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
HARMONIC DISTORTION vs LOAD RESISTANCE
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-75
-80
3rd Harmonic
-85
-90
-95
-60
Harmonic Distortion (dBc)
-70
Harmonic Distortion (dBc)
8
Output Voltage (VPP)
Frequency (Hz)
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-70
-80
3rd Harmonic
-90
-100
2nd Harmonic
-110
2nd Harmonic
-100
-120
4
5
6
7
8
9
10
11
12
10
100
Supply Voltage (±VS)
Figure 29.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ORDER INTERMODULATION INTERCEPT
55
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-85
-90
50
Intercept Point (dBm)
Harmonic Distortion (dBc)
Resistance (W)
Figure 28.
-80
3rd Harmonic
-95
45
40
35
30
25
-100
2nd Harmonic
GDIFF = 10V/V
GCM = 1V/V
20
15
-105
1
10
20
0
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 30.
14
1k
Figure 31.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±12V, 50% Bias
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
50% BIAS FREQUENCY RESPONSE
LARGE-SIGNAL FREQUENCY RESPONSE
3
3
0
Normalized Gain (dB)
Normalized Gain (dB)
VO = 2VPP
GDIFF = 5V/V
RF = 1.5kW
0
-3
GDIFF = 10V/V
RF = 1.24kW
-6
-9
-12
GCM = 1V/V
VO = 2VPP
RL = 100W
-15
-18
VO = 4VPP
-6
VO = 8VPP
-9
VO = 20VPP
-12
-18
100
0
300
40
60
80
100 120 140 160 180 200 220
Frequency (MHz)
Figure 32.
Figure 33.
DIFFERENTIAL PULSE RESPONSE
SUPPLY CURRENT FOR FULL BIAS SETTINGS vs RADJ
14
8
0.8
12
4
0.4
0
0
-0.4
Large-Signal Pulse Response
(±10VP) Left Scale
-12
10
±IQ (mA)
Small-Signal ±500mVP
Right Scale
Output Voltage (V)
1.2
-8
20
Frequency (MHz)
12
-4
GDIFF = 10V/V
RL = 100W
-15
10
Output Voltage (V)
-3
8
6
+IQ
4
-IQ
-0.8
2
-1.2
0
0
Time (10ns/div)
1
2
3
4
5
6
RADJ (kW)
Figure 34.
Figure 35.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
26
100
RS Optimized for 100% Bias
22pF
23
20
Gain (dB)
RS (W)
100pF
10
17
39pF
RS
470pF
THS6204
14
47pF
11
CL
VIN
1kW
VOUT
Optional
8
RS
5
1
1
100
10
1000
THS6204
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 36.
Figure 37.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
200M
15
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±12V, 50% Bias (continued)
At TA = +25°C, GDIFF = +10V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.24kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
-60
-70
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-65
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
GDIFF = 10V/V
GCM = 1V/V
RL = 100W
f = 1MHz
-70
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
3rd Harmonic
-80
2nd Harmonic
-90
-100
-75
3rd Harmonic
-80
-85
-90
2nd Harmonic
-95
-100
-110
100k
-105
10M
1M
0
30M
4
2
6
Figure 38.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
12
14
16
HARMONIC DISTORTION vs LOAD RESISTANCE
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-75
-80
3rd Harmonic
-90
-95
-65
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-70
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
10
Figure 39.
-70
-85
8
Output Voltage (VPP)
Frequency (Hz)
2nd Harmonic
-75
-80
-85
3rd Harmonic
-90
-95
-100
-105
-110
2nd Harmonic
-115
-100
-120
4
5
6
7
8
9
10
11
12
10
100
Supply Voltage (±VS)
1k
Resistance (W)
Figure 40.
Figure 41.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ORDER, INTERMODULATION INTERCEPT
55
-80
3rd Harmonic
Intercept Point (dBm)
Harmonic Distortion (dBc)
50
-85
-90
-95
GDIFF = 10V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-100
2nd Harmonic
45
40
35
30
25
GDIFF = 10V/V
GCM = 1V/V
20
15
-105
1
10
20
0
Figure 42.
16
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 43.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±6V, Full Bias
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
FULL BIAS FREQUENCY RESPONSE
3
0
0
Normalized Gain (dB)
Normalized Gain (dB)
SMALL-SIGNAL FREQUENCY RESPONSE
3
-3
-6
GDIFF = 10V/V
-9
-12
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
-15
-18
-6
-12
-18
100
75% Bias
-9
-15
10
300
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
50% Bias
10
100
Frequency (MHz)
Frequency (MHz)
Figure 44.
Figure 45.
LARGE-SIGNAL FREQUENCY RESPONSE
SMALL-SIGNAL AND LARGE-SIGNAL
PULSE RESPONSE
12
3
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
0
Output Voltage (V)
-3
VO = 4VPP
-6
8
VO = 16VPP
-9
VO = 2VPP
-12
VO = 20VPP
-15
Large-Signal Pulse Response
(±10VP) Left Scale
4
300
GDIFF = 10V/V
GCM = 1V/V
RL = 100W
RF = 1.2kW
Small-Signal ±500mVP
Right Scale
0
0
50
100
150
200
250
300
0.8
0.4
0
-4
-0.4
-8
-0.8
-12
-18
1.2
Output Voltage (V)
Normalized Gain (dB)
Full Bias
-3
-1.2
Time (10ns/div)
350
Frequency (MHz)
Figure 46.
Figure 47.
DIFFERENTIAL RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
17
100
RS Optimized for 100% Bias
14
Gain (dB)
RS (W)
470pF
10
22pF
11
RS
THS6204
100pF
39pF
8
CL
VIN
5
1kW
VOUT
Optional
47pF
RS
THS6204
1
1
100
10
1000
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 48.
Figure 49.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
300M
17
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±6V, Full Bias (continued)
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
-60
-70
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-60
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
3rd Harmonic
-80
-90
2nd Harmonic
-100
-110
100k
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
f = 1MHz
-70
3rd Harmonic
-80
-90
2nd Harmonic
-100
-110
10M
1M
0
30M
4
2
6
Figure 50.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
-90
-92
3rd Harmonic
-94
-96
2nd Harmonic
-98
-75
14
16
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-80
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
12
HARMONIC DISTORTION vs LOAD RESISTANCE
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-85
-90
-95
3rd Harmonic
-100
-105
-110
-100
2nd Harmonic
-115
4
5
6
7
8
9
10
11
12
10
100
Supply Voltage (±VS)
1k
Resistance (W)
Figure 52.
Figure 53.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ORDER INTERMODULATION INTERCEPT
60
-85
50
-90
3rd Harmonic
-95
-100
2nd Harmonic
-105
1
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
10
20
Intercept Point (dBm)
Harmonic Distortion (dBc)
10
Figure 51.
-88
40
30
20
GDIFF = 10V/V
GCM = 1V/V
10
0
0
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 54.
18
8
Output Voltage (VPP)
Frequency (Hz)
Figure 55.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±6V, Full Bias (continued)
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
SUPPLY CURRENT FOR FULL BIAS SETTING vs RADJ
20
18
16
±IQ (mA)
14
12
10
8
+IQ
6
-IQ
4
2
0
0
1
2
3
4
5
6
RADJ (kW)
Figure 56.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
19
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±6V, 75% Bias
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
75% BIAS FREQUENCY RESPONSE
LARGE-SIGNAL FREQUENCY RESPONSE
3
3
0
Normalized Gain (dB)
Normalized Gain (dB)
VO = 2VPP
GDIFF = 5V/V
RF = 1.82kW
0
-3
-6
-9
-12
GCM = 1V/V
VO = 2VPP
RL = 100W
-15
-18
GDIFF = 10V/V
RF = 1.5kW
VO = 8VPP
VO = 4VPP
-6
-9
VO = 20VPP
-12
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
-15
-18
10
100
300
0
20 40 60 80 100 120 140 160 180 200 220 240 260 280
Frequency (MHz)
Frequency (MHz)
Figure 57.
Figure 58.
DIFFERENTIAL SMALL-SIGNAL AND LARGE-SIGNAL
PULSE RESPONSE
6
1.2
4
0.8
2
0.4
0
0
SUPPLY CURRENT FOR FULL BIAS SETTING vs RADJ
16
14
Small-Signal ±500mVP
Right Scale
-2
-0.4
Large-Signal Pulse Response
(±5VP) Left Scale
-4
-6
±IQ (mA)
12
Output Voltage (V)
Output Voltage (V)
-3
10
8
+IQ
6
-IQ
4
-0.8
2
-1.2
0
0
Time (10ns/div)
1
2
3
4
5
6
RADJ (kW)
Figure 59.
Figure 60.
DIFFERENTIAL RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
17
100
22pF
RS Optimized for 100% Bias
14
470pF
39pF
Gain (dB)
RS (W)
RS
10
11
8
THS6204
CL
VIN
1kW
VOUT
Optional
100pF
RS
5
THS6204
47pF
1
1
20
100
10
1000
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 61.
Figure 62.
Submit Documentation Feedback
200M
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±6V, 75% Bias (continued)
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-60
-40
-60
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
3rd Harmonic
-70
-80
-90
2nd Harmonic
-100
-110
100k
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
f = 1MHz
-70
3rd Harmonic
-80
-90
2nd Harmonic
-100
-110
10M
1M
0
30M
4
2
6
Figure 63.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
12
14
16
HARMONIC DISTORTION vs LOAD RESISTANCE
-70
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-75
3rd Harmonic
-92
-94
-96
2nd Harmonic
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-98
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
10
Figure 64.
-88
-90
8
Output Voltage (VPP)
Frequency (Hz)
-80
-85
-90
-95
3rd Harmonic
-100
-105
2nd Harmonic
-110
-100
4
5
6
7
8
9
10
11
-115
12
10
100
Supply Voltage (±VS)
Resistance (W)
Figure 65.
Figure 66.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ORDER INTERMODULATION INTERCEPT
60
-85
50
-90
3rd Harmonic
-95
-100
2nd Harmonic
-105
1
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
10
20
Intercept Point (dBm)
Harmonic Distortion (dBc)
1k
40
30
20
10
GDIFF = 10V/V
GCM = 1V/V
0
0
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 67.
Figure 68.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
21
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS: VS = ±6V, 50% Bias
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
50% BIAS FREQUENCY RESPONSE
LARGE-SIGNAL FREQUENCY RESPONSE
3
3
0
Normalized Gain (dB)
Normalized Gain (dB)
VO = 2VPP
GDIFF = 5V/V
RF = 1.82kW
0
-3
-6
GDIFF = 10V/V
RF = 1.5kW
-9
-12
GCM = 1V/V
VO = 2VPP
RL = 100W
-15
-18
VO = 20VPP
-6
-9
-12
-18
100
0
300
40
60
80
100 120 140 160 180 200 220
Frequency (MHz)
Figure 69.
Figure 70.
DIFFERENTIAL PULSE RESPONSE
SUPPLY CURRENT FPR FULL BIAS SETTING vs RADJ
12
4
0.8
10
2
0.4
0
Small-Signal ±500mVP
Right Scale
-0.4
Large-Signal Pulse Response
(±5VP) Left Scale
-6
8
±IQ (mA)
0
Output Voltage (V)
1.2
-4
20
Frequency (MHz)
6
-2
VO = 8VPP
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
-15
10
Output Voltage (V)
VO = 4VPP
-3
6
+IQ
4
-IQ
-0.8
2
-1.2
0
0
Time (10ns/div)
1
2
3
4
5
6
RADJ (kW)
Figure 71.
Figure 72.
DIFFERENTIAL RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
20
100
RS Optimized for 100% Bias
17
100pF
22pF
Gain (dB)
RS (W)
14
10
470pF
RS
THS6204
11
39pF
8
CL
VIN
1kW
VOUT
Optional
47pF
RS
5
THS6204
1
1
22
100
10
1000
2
10M
100M
Capacitive Load (pF)
Frequency (Hz)
Figure 73.
Figure 74.
Submit Documentation Feedback
200M
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TYPICAL CHARACTERISTICS: VS = ±6V, 50% Bias (continued)
At TA = +25°C, GDIFF = +5V/V, GCM = 1V/V, RADJ = 0Ω, RF = 1.82kΩ, and RL = 100Ω, unless otherwise noted.
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-60
-40
-60
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
GDIFF = 5V/V
GCM = 1V/V
RL = 100W
f = 1MHz
3rd Harmonic
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
-70
-80
2nd Harmonic
-90
-100
-110
100k
-70
3rd Harmonic
-80
-90
2nd Harmonic
-100
-110
10M
1M
0
30M
4
2
6
Figure 75.
HARMONIC DISTORTION vs SUPPLY VOLTAGE
12
14
16
HARMONIC DISTORTION vs LOAD RESISTANCE
-70
-86
-75
-88
3rd Harmonic
-90
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-92
-94
2nd Harmonic
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
10
Figure 76.
-84
-96
8
Output Voltage (VPP)
Frequency (Hz)
-98
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
f = 1MHz
-80
-85
-90
3rd Harmonic
-95
-100
-105
2nd Harmonic
-100
-110
4
5
6
7
8
9
10
11
12
10
100
Supply Voltage (±VS)
Resistance (W)
Figure 77.
Figure 78.
HARMONIC DISTORTION vs NONINVERTING GAIN
2-TONE, 3RD-ODER INTERMODULATION INTERCEPT
60
-80
50
-85
3rd Harmonic
-90
-95
-100
2nd Harmonic
GDIFF = 5V/V
GCM = 1V/V
VO = 2VPP
RL = 100W
f = 1MHz
-105
1
10
20
Intercept Point (dBm)
Harmonic Distortion (dBc)
1k
40
30
20
10
GDIFF = 10V/V
GCM = 1V/V
0
0
5
10
15
20
25
30
Frequency (MHz)
Gain (V/V)
Figure 79.
Figure 80.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
23
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
APPLICATION INFORMATION
WIDEBAND CURRENT-FEEDBACK
OPERATION
The THS6204 gives the exceptional ac performance
of a wideband current-feedback op amp with a highly
linear, high-power output stage. Requiring only
9mA/ch quiescent current, the THS6204 swings to
within 1V of either supply rail and delivers in excess
of 380mA at room temperature. This low-output
headroom requirement, along with supply voltage
independent biasing, gives remarkable ±6V supply
operation. The THS6204 delivers greater than
145MHz bandwidth driving a 2VPP output into 100Ω
on a ±6V supply. Previous boosted output stage
amplifiers typically suffer from very poor crossover
distortion as the output current goes through zero.
The THS6204 achieves a comparable power gain
with much better linearity. The primary advantage of
a current-feedback op amp over a voltage-feedback
op amp is that ac performance (bandwidth and
distortion) is relatively independent of signal gain.
Figure 81 shows the dc-coupled, gain of +10V/V, dual
power-supply circuit configuration used as the basis
of the ±12V Electrical and Typical Characteristics. For
test purposes, the input impedance is set to 50Ω with
a resistor to ground and the output impedance is set
to 50Ω with a series output resistor. Voltage swings
reported in the electrical characteristics are taken
directly at the input and output pins, whereas load
powers (dBm) are defined at a matched 50Ω load.
For the circuit of Figure 81, the total effective load is
100Ω || 1.24kΩ || 1.24kΩ = 86.1Ω.
+12V
1/2
THS6204
RF
1.24kW
VI
RG
274W
RF
1.24kW
This approach provides for a source termination
impedance at the input that is independent of the
signal gain. For instance, simple differential filters
may be included in the signal path right up to the
noninverting inputs without interacting with the gain
setting. The differential signal gain for the circuit of
Figure 81 is:
RF
AD = 1 + 2 ´
RG
(1)
Because the THS6204 is a current feedback (CFB)
amplifier, its bandwidth is primarily controlled with the
feedback resistor value; Figure 81 shows a value of
274Ω for the AD = +10V/V design. The differential
gain, however, may be adjusted with considerable
freedom using just the RG resistor. In fact, RG may be
a reactive network providing a very isolated shaping
to the differential frequency response.
Various combinations of single-supply or ac-coupled
gain can also be delivered using the basic circuit of
Figure 81. Common-mode bias voltages on the two
noninverting inputs pass on to the output with a gain
of +1V/V since an equal dc voltage at each inverting
node creates no current through RG. This circuit does
show a common-mode gain of +1V/V from input to
output. The source connection should either remove
this common-mode signal if undesired (using an input
transformer can provide this function), or the
common-mode voltage at the inputs can be used to
set the output common-mode bias. If the low
common-mode rejection of this circuit is a problem,
the output interface may also be used to reject that
common-mode. For
instance,
most
modern
differential input ADCs reject common-mode signals
very well, while a line driver application through a
transformer will also attenuate the common-mode
signal through to the line.
VO
RL
1/2
THS6204
GDIFF = 1 +
-12V
2 ´ RF
RG
=
VO
VI
Figure 81. Noninverting Differential I/O Amplifier
24
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
DUAL-SUPPLY VDSL DOWNSTREAM
Figure 82 shows an example of a dual-supply VDSL
downstream driver. Both channels of the THS6204
are configured as a differential gain stage to provide
signal drive to the primary winding of the transformer
(here, a step-up transformer with a turns ratio of
1:1.1). The main advantage of this configuration is
the cancellation of all even harmonic distortion
products. Another important advantage for VDSL is
that each amplifier needs only to swing half of the
total output required driving the load.
+12V
20W
1/4
THS6204
IP = 159mA
RS
9.1W
RF
2kW
0.1mF
RG
1.33kW
2kW
0.1mF
20W
ZLINE
RP
2.7kW
RF
2kW
1/4
THS6204
LINE DRIVER HEADROOM MODEL
The first step in a transformer-coupled, twisted-pair
driver design is to compute the peak-to-peak output
voltage from the target specifications. This is done
using the following equations:
VRMS2
PL = 10 ´ log
(1mW) ´ RL
(4)
with PL power at the load, VRMS voltage at the load,
and RL load impedance; this gives the following:
RP
2.7kW
2kW
AFE
2VPP
Max
Assumed
1:1.1
the phone line, and also provide a means of detecting
the received signal for the receiver. The value of
these resistors (RM) is a function of the line
impedance and the transformer turns ratio (n), given
by the following equation:
ZLINE
RM =
2n2
(3)
RL
100W
RS
9.1W
VRMS =
(1mW) ´ RL ´ 10
PL
10
(5)
VP = CrestFactor ´ VRMS = CF ´ VRMS
(6)
with VP peak voltage at the load and CF Crest Factor.
VLPP = 2 ´ CF ´ VRMS
(7)
IP = 159mA
with VLPP: peak-to-peak voltage at the load.
-12V
Figure 82. Dual-Supply VDSL Downstream Driver
The analog front end (AFE) signal is ac-coupled to
the driver, and the noninverting input of each
amplifier is biased to the mid-supply voltage (ground
in this case). In addition to providing the proper
biasing to the amplifier, this approach also provides a
high-pass filtering with a corner frequency, set here at
5kHz. As the signal bandwidth starts at 26kHz, this
high-pass filter does not generate any problem and
has the advantage of filtering out unwanted lower
frequencies.
The input signal is amplified with a gain set by the
following equation:
2 ´ RF
GD = 1 +
RG
(2)
Consolidating Equation 4 through Equation 7 allows
expressing the required peak-to-peak voltage at the
load as a function of the crest factor, the load
impedance, and the power at the load. Thus,
VLPP = 2 ´ CF ´
(1mW) ´ RL ´ 10
PL
10
(8)
This VLPP is usually computed for a nominal line
impedance and may be taken as a fixed design
target.
The next step in the design is to compute the
individual amplifier output voltage and currents as a
function of VPP on the line and transformer turns ratio.
As this turns ratio changes, the minimum allowed
supply voltage changes along with it. The peak
current in the amplifier output is given by:
2 ´ VLPP
1
1
±IP =
´
´
n
2
4RM
(9)
With RF = 2kΩ and RG = 1.33kΩ, the gain for this
differential amplifier is RP = 2.1kΩ. This gain boosts
the AFE signal, assumed to be a maximum of 2VPP,
to a maximum of 3VPP.
The two back-termination resistors (9.1Ω each)
added at each terminal of the transformer make the
impedance of the modem match the impedance of
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
25
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
with VPP as defined in Equation 8, and RM as defined
in Equation 3 and shown in Figure 83.
V1, V2, R1, and R2 are given in Table 3 for ±12V
operation.
Table 3. Line Driver Headroom Model Values
RM
±12V
VPP =
2VLPP
n
VLPP
n
RL
VLPP
R1
V2
R2
0.6V
1V
1.2V
When using a synthetic output impedance circuit,
such as the one shown in Figure 82, a significant
drop is noticed in bandwidth from the bandwidth
appearing in the Electrical Characteristics tables. This
apparent drop in bandwidth for the differential signal
is a result of the apparent increase in the feedback
transimpedance as seen for each amplifier. This
feedback transimpedance equation is given below.
RM
Figure 83. Driver Peak Output Voltage
With the previous information available, it is now
possible to select a supply voltage and the turns ratio
desired for the transformer as well as calculate the
headroom for the THS6204.
The model, shown in Figure 84, can be described
with the following set of equations:
1. As available output swing:
VPP = VCC - (V1 + V2) - IP ´ (R1 + R2)
(10)
2. Or as required supply voltage:
VCC = VPP + (V1 + V2) + IP ´ (R1 + R2)
V1
1V
1+2´
ZFB = RF ´
RS
1+2´
RS
+
RL
+
RS
RP
RL
RS
RP
-
RF
RP
(12)
To increase 0.1dB flatness to the frequency of
interest, adding a serial R-C in parallel with the gain
resistor may be needed, as shown in Figure 85.
RS
1/4
THS6204
(11)
RF
The minimum supply voltage for a power and load
requirement is given by Equation 11.
RP
RM
+VCC
ZLINE
VIN
RG
RP
100W
CM
R1
RF
V1
1/4
THS6204
RS
VO
IP
Figure 85. 0.1dB Flatness Compensation Circuit
V2
R2
Figure 84. Line Driver Headroom Model
26
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
TOTAL DRIVER POWER FOR xDSL
APPLICATIONS
PTOT = 21mA (24V) +
The total internal power dissipation for the THS6204
in an xDSL line driver application will be the sum of
the quiescent power and the output stage power. The
THS6204 holds a relatively constant quiescent
current versus supply voltage—giving a power
contribution that is simply the quiescent current times
the supply voltage used (the supply voltage will be
greater than the solution given in Equation 11). The
total output stage power may be computed with
reference to Figure 86.
+VCC
IAVG =
IP
CF
RT
Figure 86. Output Stage Power Model
The two output stages used to drive the load of
Figure 83 can be seen as an H-Bridge in Figure 86.
The average current drawn from the supply into this
H-Bridge and load will be the peak current in the load
given by Equation 9 divided by the crest factor (CF)
for the xDSL modulation. This total power from the
supply is then reduced by the power in RT to leave
the power dissipated internal to the drivers in the four
output stage transistors. That power is simply the
target line power used in Equation 4 plus the power
lost in the matching elements (RM). In the examples
here, a perfect match is targeted giving the same
power in the matching elements as in the load. The
output stage power is then set by Equation 12.
IP
POUT =
´ VCC - 2PL
CF
(13)
The total amplifier power is then:
IP
PTOT = IQ ´ VCC +
´ VCC - 2PL
CF
(14)
For the ADSL CO driver design of Figure 82, the
peak current is 159mA for a signal that requires a
crest factor of 5.6 with a target line power of 20.5dBm
into 100Ω (115mW). With a typical quiescent current
of 21mA and a nominal supply voltage of ±12V, the
total internal power dissipation for the solution of
Figure 82 will be:
159mA
(24V) - 2(115mW) = 955mW
5.6
(15)
OUTPUT CURRENT AND VOLTAGE
The THS6204 provides output voltage and current
capabilities that are unsurpassed in a low-cost dual
monolithic op amp. Under no-load conditions at
+25°C, the output voltage typically swings closer than
1.1V to either supply rail; tested at +25°C swing limit
is within 1.4V of either rail into a 100Ω differential
load. Into a 25Ω load (the minimum tested load), it
delivers more than ±408mA continuous and > ±1A
peak output current.
The specifications described above, though familiar in
the industry, consider voltage and current limits
separately. In many applications, it is the voltage
times current (or V-I product) that is more relevant to
circuit operation. Refer to the Output Voltage and
Current Limitations plot (Figure 14) in the Typical
Characteristics. The X- and Y-axes of this graph
show the zero-voltage output current limit and the
zero-current output voltage limit, respectively. The
four quadrants give a more detailed view of the
THS6204 output drive capabilities, noting that the
graph is bounded by a safe operating area of 1W
maximum internal power dissipation (in this case for 1
channel only). Superimposing resistor load lines onto
the plot shows that the THS6204 can drive ±10.9V
into 100Ω or ±10.5V into 50Ω without exceeding the
output capabilities or the 1W dissipation limit. A 100Ω
load line (the standard test circuit load) shows the full
±12V output swing capability, as shown in the
Electrical Characteristics tables. The minimum
specified output voltage and current over temperature
are set by worst-case simulations at the cold
temperature extreme. Only at cold startup will the
output current and voltage decrease to the numbers
shown in the Electrical Characteristics tables. As the
output transistors deliver power, the junction
temperatures increases, decreasing the VBEs
(increasing the available output voltage swing), and
increasing the current gains (increasing the available
output current). In steady-state operation, the
available output voltage and current will always be
greater than that shown in the over-temperature
specifications, since the output stage junction
temperatures will be higher than the minimum
specified operating ambient. To maintain maximum
output stage linearity, no output short-circuit
protection is provided. This is normally not a problem
because most applications include a series-matching
resistor at the output that limits the internal power
dissipation if the output side of this resistor is shorted
to ground. However, shorting the output pin directly to
the adjacent positive power-supply pin (24-pin
package), will in most cases, destroy the amplifier. If
additional short-circuit protection is required, a small
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
27
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
series resistor may be included in the supply lines.
Under heavy output loads this will reduce the
available output voltage swing. A 5Ω series resistor in
each power-supply lead will limit the internal power
dissipation to less than 1W for an output short circuit
while decreasing the available output voltage swing
only 0.5V for up to 100mA desired load currents.
Always place the 0.1µF power-supply decoupling
capacitors after these supply current limiting resistors
directly on the supply pins.
DRIVING CAPACITIVE LOADS
One of the most demanding and yet very common
load conditions for an op amp is capacitive loading.
Often, the capacitive load is the input of an
ADC—including additional external capacitance that
may be recommended to improve the ADC linearity.
A high-speed, high open-loop gain amplifier such as
the THS6204 can be very susceptible to decreased
stability and closed-loop response peaking when a
capacitive load is placed directly on the output pin.
When the amplifier open-loop output resistance is
considered, this capacitive load introduces an
additional pole in the signal path that can decrease
the phase margin. Several external solutions to this
problem have been suggested.
When the primary considerations are frequency
response flatness, pulse response fidelity, and/or
distortion, the simplest and most effective solution is
to isolate the capacitive load from the feedback loop
by inserting a series isolation resistor between the
amplifier output and the capacitive load. This does
not eliminate the pole from the loop response, but
rather shifts it and adds a zero at a higher frequency.
The additional zero acts to cancel the phase lag from
the capacitive load pole, thus increasing the phase
margin and improving stability. The Typical
Characteristics show the recommended RS vs
Capacitive Load and the resulting frequency
response at the load. Parasitic capacitive loads
greater than 2pF can begin to degrade the
performance of the THS6204. Long printed-circuit
board (PCB) traces, unmatched cables, and
28
connections to multiple devices can easily cause this
value to be exceeded. Always consider this effect
carefully, and add the recommended series resistor
as close as possible to the THS6204 output pin (see
the Board Layout Guidelines section).
DISTORTION PERFORMANCE
The THS6204 provides good distortion performance
into a 100Ω load on ±12V supplies. Relative to
alternative solutions, it provides exceptional
performance into lighter loads and/or operation on a
dual ±6V supply. Generally, until the fundamental
signal reaches very high frequency or power levels,
the second harmonic dominates the distortion with a
negligible third harmonic component. Focusing then
on the second harmonic, increasing the load
impedance improves distortion directly. Remember
that the total load includes the feedback network—in
the noninverting configuration (see Figure 81), this is
the sum of RF + RG, whereas in the inverting
configuration it is just RF. Also, providing an
additional supply decoupling capacitor (0.01µF)
between the supply pins (for bipolar operation)
improves the second-order distortion slightly (3dB to
6dB).
In most op amps, increasing the output voltage swing
increases harmonic distortion directly. The Typical
Characteristics show the second harmonic increasing
at a little less than the expected 2x rate whereas the
third harmonic increases at a little less than the
expected 3x rate. Where the test power doubles, the
difference between it and the second harmonic
decreases less than the expected 6dB, whereas the
difference between it and the third harmonic
decreases by less than the expected 12dB. This also
shows up in the two-tone, third-order intermodulation
spurious (IM3) response curves. The third-order
spurious levels are extremely low at low-output power
levels. The output stage continues to hold them low
even as the fundamental power reaches very high
levels. As the Typical Characteristics show, the
spurious intermodulation powers do not increase as
predicted by a traditional intercept model. As the
fundamental power level increases, the dynamic
range does not decrease significantly.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
DIFFERENTIAL NOISE PERFORMANCE
As the THS6204 is used as a differential driver in
xDSL applications, it is important to analyze the noise
in such a configuration. Figure 87 shows the op amp
noise model for the differential configuration.
Dividing this expression by the differential noise gain
(GD = (1 + 2RF/RG)) gives the equivalent input
referred spot noise voltage at the noninverting input,
as shown in Equation 18.
EO =
2
2
2 ´ eN + (iN ´ RS) + 4kTRS + 2
iIRF
2
+2
4kTRF
GD
IN
(18)
Evaluating these equations for the THS6204 ADSL
circuit and component values of Figure 82 gives a
total output spot noise voltage of 38.9nV/√Hz and a
total equivalent input spot noise voltage of 7nV/√Hz.
Driver
EN
RS
IN
ERS
RF
In order to minimize the output noise due to the
noninverting input bias current noise, it is
recommended to keep the noninverting source
impedance as low as possible.
Ö4kTRF
Ö4kTRS
RG
2
EO
Ö4kTRG
RF
Ö4kTRF
IN
EN
RS
IN
ERS
Ö4kTRS
Figure 87. Differential Op Amp Noise Analysis
Model
As a reminder, the differential gain is expressed as:
2 ´ RF
GD = 1 +
RG
(16)
The output noise can be expressed as shown below:
EO =
2
GD
2
DC ACCURACY AND OFFSET CONTROL
A current-feedback op amp such as the THS6204
provides exceptional bandwidth in high gains, giving
fast pulse settling but only moderate dc accuracy.
The Electrical Characteristics show an input offset
voltage comparable to high-speed, voltage-feedback
amplifiers; however, the two input bias currents are
somewhat higher and are unmatched. While bias
current cancellation techniques are very effective with
most voltage-feedback op amps, they do not
generally reduce the output dc offset for wideband
current-feedback op amps. Because the two input
bias currents are unrelated in both magnitude and
polarity, matching the input source impedance to
reduce error contribution to the output is ineffective.
Evaluating the configuration of Figure 81, using
worst-case +25°C input offset voltage and the two
input bias currents, gives a worst-case output offset
range equal to:
VOFF = ± (NG × VOS(MAX)) + (IBN × RS/2 × NG) ± (IBI ×
RF)
where NG = noninverting signal gain
= ± (10 × 5mV) + (3µA × 25Ω × 10) ± (1.24kΩ ×
40µA)
2
2 ´ GD2 ´ eN + (iN ´ RS) + 4kTRS + 2(iIRF) + 2(4kTRFGD)
(17)
= ±50mV + 0.75mV ± 49.6mV
VOFF = –98.85mV to +100.35mV
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
29
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
POWER CONTROL OPERATION
The THS6204 provides a power control feature that
may be used to reduce system power. The four
modes of operation for this power control feature are
full-power, power cutback, idle state, and power
shutdown. These four operating modes are set
through two logic lines A0 and A1. Table 4 shows the
different modes of operation.
Table 4. Power Control Mode of Operation
MODE OF
OPERATION
BIAS 1
BIAS 2
Full bias mode
0
0
Mid bias mode
1
0
Low bias mode
0
1
Shutdown
1
1
The full-power mode is used for normal operating
condition. The power cutback mode brings the
quiescent power to 13.5mA. The idle state mode
keeps a low output impedance but reduces output
power and bandwidth. The shutdown mode has a
high output impedance as well as the lowest
quiescent power (0.5mA).
If the Bias 1 and Bias 2 pins are left unconnected, the
THS6204 shuts down.
DEVICE PROTECTION FEATURE
The THS6204 has a built-in thermal protection
feature. Should the internal junction temperature rise
above
approximately
+160°C,
the
device
automatically shuts down. Such a condition could
exist with improper heat sinking or if the output is
shorted to ground. When the abnormal condition is
fixed, the internal thermal shutdown circuit
automatically turns the device back on. This occurs at
approximately +145°C, junction temperature. Note
that the THS6204 does not have short-circuit
protection and care should be taken to minimize the
output current below the absolute maximum ratings.
THERMAL INFORMATION
The THS6204 is available in thermally-enhanced
RHF and PWP packages, which are members of the
PowerPAD family of packages. These packages are
constructed using leadframes upon which the dies
are mounted (see Figure 88 for the RHF package and
Figure 89 for the PWP package). This arrangement
results in the lead frames being exposed as thermal
pads on the underside of their respective packages.
Because a thermal pad has direct thermal contact
with the die, excellent thermal performance can be
achieved by providing a good thermal path away from
the thermal pad. Note that the PowerPAD is
electronically isolated from the active circuitry and
any pins. Thus, the PowerPAD can be connected to
any potential voltage within the absolute maximum
voltage range. Ideally, connection of the PAD to the
most negative supply plane is preferred.
The PowerPAD package allows for both assembly
and thermal management in one manufacturing
operation. During the surface-mount solder operation
(when the leads are being soldered), the thermal pad
can also be soldered to a copper area underneath the
package. Through the use of thermal paths within this
copper area, heat can be conducted away from the
package into either a ground plane or other heat
dissipating device. This is discussed in more detail in
the PCB design considerations section of this
document.
DIE
Side View (a)
Thermal
Pad
DIE
End View (b)
Bottom View (c)
(1) The thermal pad is electrically isolated from all terminals in the package.
Figure 88. Views of Thermally-Enhanced RHF Package (Representative Only—Not to Scale)
30
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
DIE
Side View (a)
Thermal
Pad
DIE
End View (b)
Bottom View (c)
(1) The thermal pad is electrically isolated from all terminals in the package.
Figure 89. Views of Thermally-Enhanced PWP Package (Representative Only—Not to Scale)
THERMAL ANALYSIS
BOARD LAYOUT GUIDELINES
Due to the high output power capability of the
THS6204, heatsinking or forced airflow may be
required under extreme operating conditions.
Maximum desired junction temperature sets the
maximum allowed internal power dissipation as
described below. In no case should the maximum
junction temperature be allowed to exceed +130°C.
Operating junction temperature (TJ) is given by TA +
PD × θJA. The total internal power dissipation (PD) is
the sum of quiescent power (PDQ) and additional
power dissipation in the output stage (PDL) to deliver
load power. Quiescent power is the specified no-load
supply current times the total supply voltage across
the part. A PDL depends on the required output signal
and load; using the previously developed model
described in the Total Driver Power for xDSL
Applications section, compute the maximum TJ using
a THS6204 QFN-24 in the circuit of Figure 81
operating at the maximum specified ambient
temperature of +85°C.
Maximum TJ = +85°C + (0.955 ´ 32°C/W) = 115.5°C
Achieving
optimum
performance
with
a
high-frequency amplifier like the THS6204 requires
careful attention to board layout parasitic and external
component types. Recommendations that optimize
performance include:
(19)
Although this is still well below the specified
maximum junction temperature, system reliability
considerations may require lower tested junction
temperatures. The highest possible internal
dissipation will occur if the load requires current to be
forced into the output for positive output voltages or
sourced from the output for negative output voltages.
This puts a high current through a large internal
voltage drop in the output transistors. The output V-I
plot shown in the Typical Characteristics includes a
boundary for 1W maximum internal power dissipation
under these conditions.
a) Minimize parasitic capacitance to any ac ground
for all of the signal I/O pins. Parasitic capacitance on
the output and inverting input pins can cause
instability; on the noninverting input, it can react with
the source impedance to cause unintentional band
limiting. To reduce unwanted capacitance, a window
around the signal I/O pins should be opened in all of
the ground and power planes around those pins.
Otherwise, ground and power planes should be
unbroken elsewhere on the board.
b) Minimize the distance (< 0.25") from the
power-supply
pins
to
high-frequency
0.1µF
decoupling capacitors. At the device pins, the ground
and power plane layout should not be in close
proximity to the signal I/O pins. Avoid narrow power
and ground traces to minimize inductance between
the pins and the decoupling capacitors. The
power-supply connections should always be
decoupled with these capacitors. An optional supply
decoupling capacitor across the two power supplies
(for bipolar operation) improves second-harmonic
distortion performance. Larger (2.2µF to 6.8µF)
decoupling capacitors, effective at lower frequency,
should also be used on the main supply pins. These
can be placed somewhat farther from the device and
may be shared among several devices in the same
area of the PCB.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
31
THS6204
SBOS416C – OCTOBER 2007 – REVISED APRIL 2009 ................................................................................................................................................... www.ti.com
c) Careful selection and placement of external
components
preserve
the
high-frequency
performance of the THS6204. Resistors should be a
very low reactance type. Surface-mount resistors
work best and allow a tighter overall layout. Metal film
and carbon composition axially leaded resistors can
also provide good high-frequency performance.
Again, keep leads and PCB trace length as short as
possible. Never use wire-wound type resistors in a
high-frequency application. Although the output pin
and inverting input pin are the most sensitive to
parasitic capacitance, always position the feedback
and series output resistor, if any, as close as possible
to the output pin. Other network components, such as
noninverting input termination resistors, should also
be placed close to the package. Where double-side
component mounting is allowed, place the feedback
resistor directly under the package on the other side
of the board between the output and inverting input
pins. The frequency response is primarily determined
by the feedback resistor value as described
previously. Increasing the value reduces the
bandwidth, whereas decreasing it gives a more
peaked frequency response. The 1.24kΩ feedback
resistor used in the Typical Characteristics at a gain
of +10V/V on ±12V supplies is a good starting point
for design. Note that a 1.5kΩ feedback resistor,
rather than a direct short, is recommended for the
unity-gain follower application. A current-feedback op
amp requires a feedback resistor even in the
unity-gain follower configuration to control stability.
d) Connections to other wideband devices on the
board may be made with short direct traces or
through onboard transmission lines. For short
connections, consider the trace and the input to the
next device as a lumped capacitive load. Relatively
wide traces (50mils to 100mils) should be used,
preferably with ground and power planes opened up
around them. Estimate the total capacitive load and
set RS from the plot of Recommended RS vs
Capacitive Load (Figure 6, Figure 24, and Figure 36).
Low parasitic capacitive loads (< 5pF) may not need
an RS because the THS6204 is nominally
compensated to operate with a 2pF parasitic load. If a
long trace is required, and the 6dB signal loss
intrinsic to a doubly-terminated transmission line is
acceptable, implement a matched impedance
transmission line using microstrip or stripline
techniques (consult an ECL design handbook for
microstrip and stripline layout techniques). A 50Ω
environment is normally not necessary on board; in
fact, a higher impedance environment improves
32
distortion (see the distortion versus load plots). With a
characteristic board trace impedance defined based
on board material and trace dimensions, a matching
series resistor into the trace from the output of the
THS6204 is used, as well as a terminating shunt
resistor at the input of the destination device.
Remember also that the terminating impedance is the
parallel combination of the shunt resistor and the
input impedance of the destination device.
This total effective impedance should be set to match
the trace impedance. The high output voltage and
current capability of the THS6204 allows multiple
destination devices to be handled as separate
transmission lines, each with their own series and
shunt terminations. If the 6dB attenuation of a
doubly-terminated transmission line is unacceptable,
a long trace can be series-terminated at the source
end only.
Treat the trace as a capacitive load in this case and
set the series resistor value as shown in the plot of
RS vs Capacitive Load (Figure 6, Figure 24, and
Figure 36). However, this does not preserve signal
integrity as well as a doubly-terminated line. If the
input impedance of the destination device is low,
there is some signal attenuation due to the voltage
divider formed by the series output into the
terminating impedance.
e) Socketing a high-speed part like the THS6204
is not recommended. The additional lead length and
pin-to-pin capacitance introduced by the socket can
create an extremely troublesome parasitic network,
which can make it almost impossible to achieve a
smooth, stable frequency response. Best results are
obtained by soldering the THS6204 directly onto the
board.
f) Use the –VS plane to conduct heat out of the
QFN-24 and TSSOP-24 PowerPAD packages. These
packages attach the die directly to an exposed
thermal pad on the bottom, which should be soldered
to the board. This pad must be connected electrically
to the same voltage plane as the most negative
supply applied to the THS6204 (in Figure 82, this
would be –12V).
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
THS6204
www.ti.com ................................................................................................................................................... SBOS416C – OCTOBER 2007 – REVISED APRIL 2009
INPUT AND ESD PROTECTION
+VS
The THS6204 is built using a very high-speed
complementary bipolar process. The internal junction
breakdown voltages are relatively low for these very
small geometry devices and are reflected in the
absolute maximum ratings table. All device pins have
limited ESD protection using internal diodes to the
power supplies, as shown in Figure 90.
Internal
Circuitry
External
Pin
These diodes provide moderate protection to input
overdrive voltages above the supplies as well. The
protection diodes can typically support 30mA
continuous current. Where higher currents are
possible (for example, in systems with ±15V supply
parts driving into the THS6204), current-limiting
series resistors should be added into the two inputs.
Keep these resistor values as low as possible, since
high values degrade both noise performance and
frequency response.
-VS
Figure 90. Internal ESD Protection
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (July 2008) to Revision C ..................................................................................................... Page
•
•
•
•
•
•
•
•
•
•
•
Added TSSOP package operating junction temperature row to Absolute Maximum Ratings table...................................... 2
Added TSSOP package operating junction temperature row to Recommended Operating Conditions table ...................... 3
Changed footnote 2 of Pin Configurations............................................................................................................................. 3
Updated Figure 13 ............................................................................................................................................................... 11
Updated Figure 14 ............................................................................................................................................................... 12
Updated Figure 18 ............................................................................................................................................................... 12
Updated Figure 31 ............................................................................................................................................................... 14
Updated Figure 43 ............................................................................................................................................................... 16
Updated Figure 55 ............................................................................................................................................................... 18
Updated Figure 68 ............................................................................................................................................................... 21
Updated Figure 80 ............................................................................................................................................................... 23
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): THS6204
33
PACKAGE OPTION ADDENDUM
www.ti.com
8-Dec-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
THS6204IPWP
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IPWPG4
ACTIVE
HTSSOP
PWP
24
60
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IPWPR
ACTIVE
HTSSOP
PWP
24
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IPWPRG4
ACTIVE
HTSSOP
PWP
24
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IRHFR
ACTIVE
VQFN
RHF
24
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IRHFRG4
ACTIVE
VQFN
RHF
24
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IRHFT
ACTIVE
VQFN
RHF
24
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
THS6204IRHFTG4
ACTIVE
VQFN
RHF
24
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
THS6204IPWPR
HTSSOP
PWP
24
2000
330.0
16.4
THS6204IRHFR
VQFN
RHF
24
3000
330.0
THS6204IRHFT
VQFN
RHF
24
250
180.0
6.95
8.3
1.6
8.0
16.0
Q1
12.4
4.3
5.3
1.3
8.0
12.0
Q1
12.4
4.3
5.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
THS6204IPWPR
HTSSOP
PWP
24
2000
367.0
367.0
38.0
THS6204IRHFR
VQFN
RHF
24
3000
367.0
367.0
35.0
THS6204IRHFT
VQFN
RHF
24
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated