RECTRON SF163S

SF161S
THRU
SF167S
GLASS PASSIVATED SUPER FAST RECTIFIER
VOLTAGE RANGE 50 to 600 Volts CURRENT 16 Amperes
FEATURES
* Low switching noise
* Low forward voltage drop
* Low thermal resistance
* High current capability
* Super fast switching speed
* High reliability
* Good for switching mode circuit
.049 (1.25 REF.)
D2-PAK
.049 (1.25)
.083 (2.10)
.098 (2.50)
.012 (0.30)
.198 (5.03)
.412 (10.46)
Single phase, half wave, 60 Hz, resistive or inductive load.
.053 (1.35)
.020 (0.50)
.202 (5.13)
Ratings at 25 o C ambient temperature unless otherwise specified.
.173 (4.40)
.053 (1.35)
.069 (1.75)
.055 (1.40)
.047 (1.20)
.036 (0.91)
.028 (0.71)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
.189 (4.80)
.576 (14.64)
PIN2
.110 (2.80)
.126 (3.20)
PIN1
.624 (15.84)
.346 (8.8)
* Case: D2-PAK molded plastic
* Epoxy: Device has UL flammability classification 94V-O
* Lead: MIL-STD-202E method 208C guaranteed
* Mounting position: Any
* Weight: 1.35 grams
.323 (8.2)
MECHANICAL DATA
PIN 1
.388 (9.86)
For capacitive load, derate current by 20%.
PIN 2
HEATSINK
Dimensions in inches and (millimeters)
MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted)
SYMBOL
SF161S
SF162S
SF163S
SF164S
SF165S
SF166S
SF167S
UNITS
Maximum Recurrent Peak Reverse Voltage
RATINGS
VRRM
50
100
150
200
300
400
600
Volts
Maximum RMS Voltage
VRMS
35
70
105
140
210
280
420
Volts
VDC
50
100
150
200
300
400
600
Volts
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
at T C = 100 o C
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
Typical Thermal Resistance (Note 4)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range
IO
16.0
Amps
I FSM
300
Amps
R q JA
16
R q JC
1.2
CJ
400
T J, T STG
-55 to + 150
0
C/ W
pF
0
C
ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted)
O
CHARACTERISTICS
Maximum Instantaneous Forward Voltage at 16.0A DC
Maximum DC Reverse Current
at Rated DC Blocking Voltage
@T A = 25 o C
@T A = 100 o C
Maximum Reverse Recovery Time (Note 1)
SYMBOL
VF
SF161S
SF162S
SF163S
trr
SF165S
SF166S
1.35
10
IR
NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A
2. Measured at 1 MHz and applied reverse voltage of 4.0 volts.
3. Suffix "R" for Reverse Polarity.
4. Typical Thermal Resistance : Heat-sink mounted.
5. "Fully ROHS complaint", "100% Sn plating (Pb-free)"
SF164S
1.0
UNITS
1.70
Volts
mAmps
500
35
SF167S
50
nSec
2007-3
Single Phase Half Wave
60 Hz Inductive or
Resistive Load
4
0
0
50
100
150
CT, JUNCTION CAPACITANCE, (pF)
TA = 25 OC
1.0
20
40
60
66
S
0.6
1000
TA = 100 OC
80
0.8
1.0
1.2
1.4
1.6
1.8
2.0
100
120
FIG.2 TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
100
T J = 25 OC
10
0.1 0.2
140
0.4
1.0
PERCENT RATED PEAK REVERSE VOLTAGE, (%)
2
8.3mS Single Half Sine-Wave
JEDEC Method
250
200
150
100
50
1
2
10
20
40
100
FIG.4 TYPICAL JUNCTION CAPACITANCE
300
0
4
REVERSE VOLTAGE, (V)
FIG.3 TYPICAL REVERSE CHARACTERISTICS
PEAK FORWARD SURGE CURRENT, (A)
INSTANTANEOUS REVERSE CURRENT, (mA)
FIG.1 TYPICAL FORWARD CURRENT
DERATING CURVE
0
7S
2
1.0
INSTANTANEOUS FORWARD VOLTAGE, (V)
10
0.1
16
T A = 25 OC
Pulse Width = 300mS
1% Duty Cycle
O
100
~S
4
CASE TEMPERATURE, ( C)
1000
F1
S
10
16
S~
12
5S
SF
164
14
SF
8
20
SF
12
30
161
16
50
SF
20
INSTANTANEOUS FORWARD CURRENT, (A)
AVERAGE FORWARD CURRENT, (A)
RATING AND CHARACTERISTICS CURVES ( SF161S THRU SF167S )
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.5 MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
DISCLAIMER NOTICE
Rectron Inc reserves the right to make changes without notice to any product
specification herein, to make corrections, modifications, enhancements or other
changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information
contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or
use of any product or circuit.
Rectron products are not designed, intended or authorized for use in medical,
life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in
such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.