SF2131B • Low Insertion Loss • 5.0 X 7.0 mm Surface-Mount Case • Complies with Directive 2002/95/EC (RoHS) 92.16 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Maximum DC Voltage Between any Two Terminals 30 VDC -40 to +85 °C Storage Temperature Range in Tape and Reel Maximum Soldering Profile 265 °C for 10 s SMP-03 Electrical Characteristics Characteristic Sym Nominal Center Frequency 1.5 dB Passband Bandwidth Minimum Insertion Loss Attenuation Relative to ILMIN fC ILMIN 0 to 40.72 MHz 40.72 to 66 MHz 61.44 to 122.88 MHz 109 to 143.6 MHz 143.6 to 153.6 MHz 218 to 1000 MHz 82.16 to 102.16 MHz 82.16 to 102.16 MHz 82.16 to 102.16 MHz Amplitude Ripple Group Delay Ripple 1 dB Compression Point Input IP3 Operating Temperature Range Terminating Source/Load Impedance Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Notes 1 Min 1, 4 1, 4 1, 5 1 1 Max Units 10.0 MHz MHz dB 20 1, 2 1, 3 Typ 92.16 42 45 52 40 56 58 12 35 -40 9 50 49.5 56 45 60 63 0.9 65 15 40 dB 1.2 100 +85 50 SMP-03 7 x 5 mm Nominal Footprint RFM SF2131B YYWWS dBP-P nsP-P dBm dBm °C ohm CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. The design, manufacturing process, and specifications of this filter are subject to change. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 1 of 4 SF2131B - 7/9/09 SF2131B I/O Impedance (matched) and Amplitude Plots 5 Mar 2009 12:59:52 CH1 S11 1 U FS 0 . 2402 1 : 37 . 031 92 . 160 000 MHz SF2131B SMALL PCB 414 . 87 CH3 S22 1 : 25 . 000 92 . 160 000 pH 1 U FS -2 . 9297 MHz 1 m 589 . 46 nF 1 Cor Cor Full CENTR CH2 92 . 160 S21 MHz LOG SPAN 100 . 000 10 dB/ MHz CENTR REF -9.011 dB 92 . 160 1 : 0. 0000 MHz dB SPAN 100 . 000 0 . 000 000 MHz MHz 1 CH2 Max BW: Cor Full 2 3 4 cent : Markers REF=1 22 . 142515 MHz 92 . 136991 MHz Q: 4. 1611 1_ loss CENTER 92 . 160 000 MHz SPAN 100 . 000 000 : -9 . 0137 dB MHz SF2131B Matching Network L1 IN 9 8 7 10 6 330nh sf2131b demo small PCB L2 1 5 2 3 OUTPUT 4 240nh c1 PCB IND IND CAP 400-1608-001 501-0782-331 501-0782-241 501-1275-150 www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. small PCB, 5X7 0805, 330 nH 0805, 240 nH 0805, 15 pF 15pf PCB L1 L2 C1 Page 2 of 4 SF2131B - 7/9/09 Tape and Reel Specifications "B" REF. 100 REF. “B “ Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 9.4 mm Bo 7.4 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 3 of 4 SF2131B - 7/9/09 SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions Dimension A B C D E H J K P Recommended PCB Footprint mm Inches Min Nom Max Min Nom Max 6.80 4.80 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 0.268 0.189 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 .47 2.41 0.87 4.87 2.87 1.14 0.019 0.095 0.034 0.192 0.113 0.045 Electrical Connections Connection Port 1 Port 2 Terminals Input or Return 10 Return or Input 1 Output or Return 5 Return or Output 6 Ground All others Single-ended Operation Return is ground Differential Operation Return is hot Materials Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free C B E H H A J D P K www.RFM.com E-mail: [email protected] ©2009 by RF Monolithics, Inc. Page 4 of 4 SF2131B - 7/9/09