SPWNE555D Single Timer Elektronische Bauelemente RoHS Compliant Product DIP-8 Description D The SPWNE555D is a highly stable timer integrated circuit. It can be operated in Astable mode and Monostable mode. With monostable operation, the time delay is controlled by one external and one capacitor. With a stable operation, the frequency and duty cycle are accurately controlled with two external resistors and one capacitor. E GAUGE PLANE c A Features SEATING PLANE Z SECTION Z - Z * Timing From uSec to Hours * Time Delay Generation * Pulse Generation * Precistion Timing e b * High Current Driver Capability (=200mA) Applications b Z L * Turn Off Time Less Than 2uSec * Adjustable Duty Cycle REF. A A1 A2 b b1 b2 b3 c Millimeter Min. Max. 0.381 2.921 0.356 0.356 1.143 0.762 0.203 0.5334 4.953 0.559 0.508 1.778 1.143 0.356 REF. c1 D E E1 e HE L Millimeter Min. Max. 0.203 0.279 9.017 10.16 6.096 7.112 7.620 8.255 2.540 BSC 10.92 2.921 3.810 Block Diagram & Pin Configuration rogrammed by pacitor CT to ground .Operation 500kHz nts up to This is the reference output .It provides charging current for capacitor CT http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 1 of 5 SPWNE555D Elektronische Bauelemente Single Timer : Absolute Maximum Ratings (Ta=25 ) Parameter Supply Voltage Output Current Power Dissipation Lead Temperature (10sec) Operating Temperature Storage Temperature Symbol VCC IO Pd Tlead Topr Tstg Electrical Characteristics Parameter Supply Voltage Supply Current (Note 1) Timing Error(monostable) Initial Accurary (Note 1) Drift with Temperature Drift with Supply Voltage Timing Error(astable) Initial Accurary (Note 1) Drift with Temperature Drift with Supply Voltage Control Voltage Threshold Voltage Threshold Current (Note 3) Trigger Voltage Trigger Current Reset Voltage Reset Current Low Output Voltage High Output Voltage Reset Time of Output Fall Time of Output Discharge leakage Current (TA=25 Symbol VCC ICC Value 16 200 600 300 0 ~ 70 -65 ~ 150 Unit V mA mW V CC=5 ~ 15V) Test Conditions VCC=5V, RL= VCC=15V, RL= ACCUR RA=1k to 100k t/ T C=0.1 F t/ VCC ACCUR RA=1k to 100k t/ T C=0.1 F t/ VCC VCC=15V VC VCC=5V VCC=15V VTH VCC=5V ITH VCC=5V nd resistor set Vtr VCC=15V Itr Vtr=0 Vrst Irst VCC=15V, Isink=10mA VOL VCC=15V, Isink=50mA VCC=5V, Isink=5mA VCC=15V, Isink=200mA VOH VCC=15V, Isink=100mA VCC=5V, Isink=100mA tR tF ILKG Min 4.5 - Typ. 3 10 Max. 16 6 15 Unit V mA mA - 1.0 50 0.1 - % ppm/ %/V 2.25 % ppm/ 150 0.3 %/V 9.0 10.0 11.0 V 2.6 3.33 4.0 V 9.2 10.0 10.8 V 3.1 3.33 3.55 this pin (with a 5.0uF capacitor at V Pin 2) on time- of the0.1 circuit is0.25 affected by A the 1.1 1.67 2.2 V low frequency rolloff and input impedance. The 4.5 5 5.6 V 2.0 A 0.4 0.7 1.0 V 0.1 0.4 mA 0.06 0.25 V 0.3 0.75 0.05 0.35 12.5 V 12.75 13.3 15 2.75 3.3 5 100 nSec 100 nSec 20 100 nA Note1: Supply current when output is high typically 1mA less at VCC=5V. Note2: Tested at VCC=5V and VCC=15V. Note3: This will determine the maximum value of RA+RB for 15V operation, the maximum total is R=20M , and for 5V operation the maximum total is R=6.7M . http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 2 of 5 SPWNE555D Elektronische Bauelemente Single Timer Characteristics Curve (UVLO) VCC = 15 V ht tp://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 3 of 5 SPWNE555D Elektronische Bauelemente vs. Output Power http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A Single Timer Load Any changing of specification will not be informed individual Page 4 of 5 SPWNE555D Elektronische Bauelemente Single Timer Application Circuit FLIP-FLOP Application Notes The application circuit shows astable mode configuration. Pin 6 (Threshold) is tied to Pin 2 (Trigger) and Pin 4 (Reset) is tied to VCC (Pin 8). The external capacitor C1 of Pin 6 and Pin 2 charges through RA, RB and discharge through RB only. In the internal circuit of SPWNE555D, one input of the upper comparator is at voltage of 2/3VCC (R1=R2=R3), another input is connected to Pin 6. As soon as C1 is charging to higher than 2/3VCC, transistor Q1 is turned ON and discharge C1 to collector voltage of transistor Q1. Therefore, the flip-flop circuit is reset and output is low. One input of lower comparator is at voltage of 1/3VCC, discharge transistor Q1 turn off and C1 charges through RA and RB. Therefore, flip-flop circuit is set output high. That is, when C1 charges through RA and RB, output is high and when C1 discharge through RB, output is low. The charge time (output is high) t1 is 0.693 (RA+RB) C1 and the discharge time (output is low) T2 is 0.693RB*C1. In 1 VccVcc Vcc 3 Vcc Vcc Vcc Vcc- 2 Vcc Vcc Vcc 13 =0.693 T1=0.693*(RA+RB)*C1 Thus the total period time T is given by T2=0.693*RB*C1 T=T1+T2=0.693(RA+2RB)*C1. Then the frequency of astable mode is given by f= 1 T = 1.44 1.44 (RA+2RB)*C1 (RA+2RB)*C1 The duty cycle is given by D.C. = T2 T = http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A RB RA+2RB RA+2RB . Any changing of specification will not be informed individual Page 5 of 5