TI TLV320AIC11CPFB

GeneralĆPurpose LowĆVoltage
1.1 V to 3.6 V I/O 16ĆBit
22ĆKSPS DSP CODEC
TLV320AIC11
Data Manual
2000
AAP Data Converter Group
SLWS100
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  2000, Texas Instruments Incorporated
Contents
Section
1
2
Title
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
1.2
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
1.3
Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
1.4
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
1.5
Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
1.6
Definitions and Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6
1.7
Register Functional Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.1
Device Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.1.1
Operating Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.1.2
ADC Signal Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
2.1.3
DAC Signal Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
2.1.4
MIC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
2.1.5
Antialiasing Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.6
Sigma-Delta ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.7
Decimation Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.8
Sigma-Delta DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.9
Interpolation Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.10
Analog and Digital Loopback . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.11
FIR Overflow Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.12
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
2.1.13
Automatic Cascading Detection (ACD) . . . . . . . . . . . . . . . . 2–6
2.1.14
Low-Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
2.1.15
Event-Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
2.2
Reset and Power-Down Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
2.2.1
Software and Hardware Reset . . . . . . . . . . . . . . . . . . . . . . . . 2–7
2.2.2
Software and Hardware Power Down . . . . . . . . . . . . . . . . . . 2–7
2.3
Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.4
Data Out (DOUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.4.1
Data Out, Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.4.2
Data Out, Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.5
Data In (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.6
FC (Hardware Secondary Communication Request) . . . . . . . . . . . . . 2–8
2.7
Frame-Sync Function for TLV320AIC11 . . . . . . . . . . . . . . . . . . . . . . . . 2–8
2.7.1
Frame-Sync (FS) Function—Continuous-Transfer Mode
(Master Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
iii
2.7.2
3
4
iv
Frame-Sync (FS) Function—Fast-Transfer Mode
(Slave Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.3
Frame-Sync (FS) Function—Master Mode . . . . . . . . . . . . .
2.7.4
Frame-Sync (FS) Function—Slave Mode . . . . . . . . . . . . . .
2.7.5
Frame-Sync Delayed (FSD) Function, Cascade Mode . . .
2.8
Multiplexed Analog Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.1
Multiplexed Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.2
Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.3
Single-Ended Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.4
Single-Ended Analog Output . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Primary Serial Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Secondary Serial Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Register Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Hardware Secondary Serial Communication Request . . . .
3.2.3
Software Secondary Serial Communication Request . . . .
3.3
Direct Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Continuous Data Transfer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
DIN and DOUT Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1
Primary Serial Communication DIN and
DOUT Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2
Secondary Serial Communication DIN and
DOUT Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.3
Direct Configuration DCSI Data Format . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Absolute Maximum Ratings Over Operating Free-Air
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Electrical Characteristics Over Recommended Operating
Free-Air Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
Digital Inputs and Outputs, Fs = 8 kHz,
Output Not Loaded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
ADC Path Filter, Fs = 8 kHz . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
ADC Dynamic Performance, Fs = 8 kHz . . . . . . . . . . . . . . .
4.3.4
ADC Channel Characteristics . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5
DAC Path Filter, Fs = 8 kHz . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.6
DAC Dynamic Performance . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.7
DAC Channel Characteristics . . . . . . . . . . . . . . . . . . . . . . . .
4.3.8
Op-Amp Interface (A1, A3, A4) . . . . . . . . . . . . . . . . . . . . . . .
4.3.9
Op-Amp Interface (A1, A3, A4) . . . . . . . . . . . . . . . . . . . . . . .
4.3.10
Power-Supply Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.11
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
Master Mode Timing Requirements . . . . . . . . . . . . . . . . . . .
4.4.2
Slave Mode Timing Requirements . . . . . . . . . . . . . . . . . . . .
2–10
2–11
2–11
2–12
2–13
2–13
2–13
2–14
2–14
3–1
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–8
3–8
3–8
4–1
4–1
4–1
4–1
4–1
4–2
4–2
4–3
4–3
4–3
4–4
4–4
4–4
4–4
4–5
4–5
4–5
4–5
5 Parameter Measurement Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
6 Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
Appendix A—Register Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–1
List of Illustrations
Figure
Title
2–1 Timing Sequence of ADC Channel (Primary Communication Only) . . . . . .
2–2 Timing Sequence of ADC Channel (Primary and
Secondary Communication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3 Timing Sequence of DAC Channel (Primary Communication Only) . . . . . .
2–4 Timing Sequence of DAC Channel (Primary and Secondary
Communication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–5 Typical Microphone Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–6 Cascading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–7 Event Monitor Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–8 Internal Power-Down Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–9 Timing Diagram for the FS Pulse Mode (M1M0 = 00) . . . . . . . . . . . . . . . . . .
2–10 Timing Diagram for the SPI_CP0 Mode (M1M0 = 01) . . . . . . . . . . . . . . . . .
2–11 Timing Diagram for the SPI_CP1 Mode (M1M0 = 10) . . . . . . . . . . . . . . . . .
2–12 Timing Diagram for the FS Frame Mode (M1M0 = 11) . . . . . . . . . . . . . . . .
2–13 Master Device Frame-Sync Signal With Primary and Secondary
Communication ( No Slaves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–14 Master Device’s FS Output to DSP and FSD Output to the Slave . . . . . . .
2–15 Cascade Mode Connection (to DSP Interface) . . . . . . . . . . . . . . . . . . . . . . .
2–16 Master-Slave Frame-Sync Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–17 INP and INM Internal Self-Biased Circuit (2.5 V for 5-V Operation
and 1.5 V for 3-V Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–18 Differential Output Drive (Ground-Referenced) . . . . . . . . . . . . . . . . . . . . . . .
2–19 Single-Ended Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–20 Single-Ended Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1 Primary Serial Communication Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–2 Hardware and Software Secondary Communication Request . . . . . . . . . . .
3–3 Device 3/Register 1 Read Operation Timing Diagram . . . . . . . . . . . . . . . . . .
3–4 Device 3/Register 1 Write Operation Timing Diagram . . . . . . . . . . . . . . . . . .
3–5 FS Output When Hardware Secondary Serial Communication
Is Requested Only Once (No Slave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–6 Output When Hardware Secondary Serial Communication Is
Requested (Three Slaves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–7 FS Output During Software Secondary Serial Communication Request
(No Slave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2–1
2–2
2–3
2–3
2–4
2–6
2–6
2–7
2–9
2–9
2–10
2–10
2–11
2–11
2–12
2–12
2–13
2–13
2–14
2–14
3–1
3–2
3–3
3–4
3–4
3–5
3–5
v
3–8 Direct Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–9 Direct Configuration Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–10 Continuous Data Transfer Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–11 Primary Communication DIN and DOUT Data Format . . . . . . . . . . . . . . . .
3–12 Secondary Communication DIN and DOUT Data Format . . . . . . . . . . . . . .
3–13 Direct Communication DCSI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1 FS and FSD Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–2 Serial Communication Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–3 FFT–ADC Channel, Fs = 8 kHz, Input = –3 dB . . . . . . . . . . . . . . . . . . . . . . . .
5–4 FFT–DAC Channel, Fs = 8 kHz, Input = –3 dB . . . . . . . . . . . . . . . . . . . . . . . .
5–5. FFT–ADC Channel, Fs = 8 kHz, Input = –1 dB . . . . . . . . . . . . . . . . . . . . . . .
5–6 FFT–DAC Channel, Fs = 8 kHz, Input = 0 dB . . . . . . . . . . . . . . . . . . . . . . . . .
3–6
3–6
3–7
3–8
3–8
3–8
5–1
5–1
5–2
5–2
5–3
5–3
List of Tables
Table
Title
Page
2–1 Serial Interface Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
3–1 Least Significant Bit Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
vi
1 Introduction
The TLV320AIC11 provides high resolution signal conversion from digital-to-analog (D/A) and from analog-to-digital
(A/D) using oversampling sigma-delta technology. It allows 2-to-1 MUX inputs with built-in antialiasing filter and
amplification for general-purpose applications such as telephone hybrid interface, electret microphone preamp, etc.
Both IN and AUX inputs accept normal analog signals. This device consists of a pair of 16-bit synchronous serial
conversion paths (one for each direction), and includes an interpolation filter before the DAC and a decimation filter
after the ADC. The FIR filters can be bypassed to offer flexibility and power savings. Other overhead functions
provided on-chip include timing (programmable sample rate, continuous data transfer, and FIR bypass) and control
(programmable-gain amplifier, communication protocol, etc.). The sigma-delta architecture produces high-resolution
analog-to-digital and digital-to-analog conversion at low system cost.
The TLV320AIC11 design enhances communication with the DSP. The continuous data transfer mode fully supports
TI’s DSP autobuffering (ABU) to reduce DSP interrupt service overhead. The automatic cascading detection (ACD)
makes cascade programming simple and supports a cascade operation of one master and up to seven slaves. The
direct-configuration mode for host interface uses a single-wire serial port to directly program internal registers without
interference from the data conversion serial port, or without resetting the entire device. The event monitor mode
allows the DSP to monitor external events like telephone’s ring and off-hook detection.
In the lower-power mode, the TLV320AIC11 converts data at a sampling rate of 8 KSPS consuming only 39 mW.
The programmable functions of this device are configured through a serial interface that can be gluelessly interfaced
to any DSP that accepts 4-wire serial communications, such as the TMS320UC54x. The options include software
reset, device power-down, separate control for ADC and DAC turnoff, communications protocol, signal-sampling
rate, gain control, and system-test modes, as outlined in Appendix A.
The TLV320AIC11 is particularly suitable for a variety of applications in hands-free car kits, VOIP, cable modem,
speech, and telephony area including low-bit rate, high-quality compression, speech enhancement, recognition, and
synthesis. Its low-group delay characteristic makes it suitable for single or multichannel active-control applications.
The wide range of low-voltage I/O (1.1 V–3.6 V) enables the AIC11 to interface with a single power supply, or with
dual power supplies for mixed low-voltage DSP systems such as the TMS320UC54x. This feature eliminates the
need for external level-shifting and reduces power consumption.
The TLV320AIC11 is characterized for commercial operation from 0°C to 70°C, and industrial operation from –40°C
to 85°C.
1.1 Features
•
16-bit oversampling sigma-delta A/D converter
•
16-bit oversampling sigma-delta D/A converter
•
Maximum output conversion rate:
•
–
22 ksps with on-chip FIR filter
–
88 ksps with FIR bypassed
Voiceband bandwidth in FIR-bypassed mode and final sampling rate at 8 ksps
–
90-dB SNR/ADC and 87-dB SNR/DAC with DSP’s FIR (FIR bypassed @ 88 ksps/5 V)
–
87-dB SNR/ADC and 85-dB SNR/DAC with DSP’s FIR (FIR bypassed @88 ksps/3.3 V)
•
On-chip FIR produced 84-dB SNR for ADC and 85-dB SNR for DAC over 11-kHz BW
•
Built-in functions including PGA, antialiasing analog filter, and op-amps for general-purpose interface (such
as MIC interface and hybrid interface)
1–1
1–2
•
Glueless serial port interface to DSPs (TI TMS320UC54x or standard DSPs)
•
Automatic cascading detection (ACD) makes cascade programming simple and allows up to 8 devices to
be connected in cascade.
•
On-fly reconfiguration modes include secondary-communication mode and direct-configuration mode (host
interface).
•
Continuous data-transfer mode for use with autobuffering (ABU) to reduce DSP interrupt service overhead
•
Event-monitor mode provides external-event control, such as RING/OFF-HOOK detection
•
Programmable ADC and DAC conversion rate
•
Programmable input and output gain control
•
Separate software control for ADC and DAC power-down
•
Low-voltage (DVDD1) 1.1-V to 3.6-V digital I/O
•
Analog (AVDD1 and AVDD2) 3 V to 5.5 V core power supply
•
Digital (DVDD2) 3 V to 5.5 V core power supply
•
Power dissipation (PD) of 39 mW typical for 8-ksps at 3.3 V
•
Hardware power-down mode to 0.2 mW
•
Internal and external reference voltage (Vref)
•
Differential and single-ended analog input/output
•
2s-complement data format
•
Test mode, which includes digital loopback and analog loopback
•
600-ohm output driver
•
VHDL code for serial interface available
1.2 Functional Block Diagram
Receiver or MIC Amp
AURXFP
+
AURXCP
–
A1
AURXM
Decimation Filter
INP
AntiAliasing
Filter
MUX
INM
PGA
SigmaDelta
ADC
Sync
Filter
FIR
Filter
DOUT
Digital
Loopback
ADREFP
ADREFM
VMID
@ 5 mA
A2
DIN
Vref
DAREFP
DAREFM
Interpolation Filter
Analog
Loopback
OUTP
PGA
Low
Pass
Filter
SigmaDelta
DAC
Sync
Filter
M/S
FSD
Interface
Circuit
SCLK
FIR
Filter
FLAG
OUTM
DTXOP
DTXIM
DCSI
Transmitter Amp
ALTI
FC
–
A3
+
DTXIP
FS
+
A4
–
M0
1.5 V
or
2.5V
M1
Internal Clock Circuit
Div
256xN
MCLK
DTXOM
1–3
1.3 Terminal Assignments
INM
INP
AV SS
AV DD1
NC
VMID
AV SS
NC
AV SS
NC
FILT
NC
PFB PACKAGE
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
AURXFP
AURXM
AURXCP
DTXOP
DTXOM
DTXIP
DTXIM
OUTP
OUTM
M0
M1
PWRDWN
1
36
2
35
3
34
4
33
5
32
6
31
7
30
8
29
9
28
10
27
11
26
12
25
NC
NC
AVDD2
AVSS
NC
NC
DVDD2
DVSS
NC
M/S
ALTIN
DCSI
RESET
DV SS
DV DD1
DOUT
DIN
NC
SCLK
MCLK
FSD
FS
FLAG
FC
13 14 15 16 17 18 19 20 21 22 23 24
NOTE: All NC pins should be left unconnected.
1.4 Ordering Information
PACKAGE
TA
48-TQFP PFB
0°C to 70°C
TLV320AIC11C
–40°C to 85°C
TLV320AIC11I
1.5 Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
ALTIN
26
I
Serial input in the event monitor mode
AURXCP
3
I
Receiver-path/GP amplifier noninverting input. It needs to be connected to AVSS if not used.
AURXM
2
I
Receiver-path amplifier A1 inverting input, or inverting input to auxiliary analog input. It needs to be connected
to AVSS if not used. It can also be used for general-purpose amplification.
AURXFP
1
I
Receiver-path amplifier A1 feedback, or noninverting input to auxiliary analog input. It needs to be connected
to AVSS if not used. It can also be used for general-purpose amplification.
AVDD1
AVDD2
45
34
I
Analog ADC power supply (3 V to 5.5 V)
AVSS
33, 40, 42,
46
I
Analog ground
DCSI
25
I
Direct configuration serial input for directly programming of internal control registers
DIN
17
I
Data input. DIN receives the DAC input data and register data from the external digital signal processor (DSP),
and is synchronized to SCLK and FS. Data is latched at the falling edge of SCLK when FS is low. DIN is at high
impedance when FS is not activated.
1–4
1.5 Terminal Functions (Continued)
TERMINAL
NAME
NO.
I/O
DESCRIPTION
DOUT
16
O
Data output. DOUT transmits the ADC output bits and registers data, and is synchronized to SCLK and FS.
Data is sent out at the rising edge of SCLK when FS is low. DOUT is at high impedance when FS is not
activated.
DTXIM
7
I
Transmitter-path amplifier A3 analog inverting input. It can also be used for general-purpose amplification.
DTXIP
6
I
Transmitter-path amplifier A4 analog noninverting input. Can also be used for general-purpose
amplification.
DTXOP
4
O
Transmitter-path amplifier A3 feedback for positive output. It can also be used for general-purpose
amplification.
DTXOM
5
O
Transmitter path amplifier A4 feedback for negative output. It can also be used for general-purpose
amplification.
DVDD1
15
I
Dedicated 1.1-V to 3.6-V digital power supply for low-voltage I/O
DVDD2
30
I
Dedicated 3-V to 5.5-V digital power supply for core CODEC
14, 29
I
Digital ground
FC
24
I
Hardware request for secondary communication
FILT
38
O
Bandgap filter. FILT is provided for decoupling of the bandgap reference, and provides 2.5 V. The optimal
capacitor value is 0.1 µF (ceramic). This voltage node should be loaded only with a high-impedance dc load.
FLAG
23
O
Controlled by bit D4 of control register 3. If D4=0 (default), the FLAG pin outputs the communication flag that
goes low/high to indicate primary-communication/secondary-communication interval, respectively. If D4=1,
the FLAG pin outputs the value of D3.
FS
22
I/O
Frame sync. When FS goes low, DIN begins receiving data bits and DOUT begins transmitting data bits. In
master mode, FS is internally generated and is low during data transmission to DIN and from DOUT. In slave
mode, FS is externally generated.
FSD
21
O
Frame-sync delayed output. The FSD output synchronizes a slave device to the frame sync of the master
device. FSD is applied to the slave FS input and has the same duration as the master FS signal.
INM
48
I
Inverting input to analog modulator. INM requires an external R-C antialias filter with low output impedance if
the internal antialias filter is bypassed.
INP
47
I
Noninverting input to analog modulator. INP requires an external R-C antialias filter with low output
impedance if the internal antialias filter is bypassed.
M0
10
I
Combine with M1 to select serial interface mode (frame-sync mode)
M1
11
I
Combine with M0 to select serial interface mode (frame-sync mode)
MCLK
20
I
Master clock. MCLK derives the internal clocks of the sigma-delta analog interface circuit.
M/S
27
I
Master/slave select input. When M/S is high, the device is the master, and when M/S is low, it is a slave.
NC
18, 28, 31,
32, 35, 36,
37, 39, 41,
44
DVSS
No connection
OUTM
9
O
DAC’s inverting output. OUTM is functionally identical with and complementary to OUTP.
OUTP
8
O
DAC’s noninverting output. OUTP can also be used alone for single-ended operation.
PWRDWN
12
I
Power down. When PWRDWN is pulled low, the device goes into a power-down mode, the serial interface is
disabled, and most of the high-speed clocks are disabled. However, all register values are sustained and the
device resumes full-power operation without reinitialization when PWRDWN is pulled high again.
PWRDWN resets the counters only and preserves the programmed register contents. See paragraph 2.2.2
for more information.
RESET
13
I
Reset. The reset function is provided to initialize all the internal registers to their default values. The serial
port can be configured to the default state accordingly. See Appendix A, Register Set, and Subsection 2.2.1,
Reset and Power-Down Functions for detailed descriptions.
SCLK
19
I/O
Shift clock. SCLK signal clocks serial data into DIN and out of DOUT during the frame-sync interval. When
configured as an output (M/S high), SCLK is generated internally by multiplying the frame-sync signal
frequency by 256 (cascade devices < 5) or 512 (cascade devices > 4). When configured as an input (M/S
low), SCLK is generated externally and must be synchronous with the master clock and frame sync.
VMID
43
O
Reference voltage output at AVDD/2
1–5
1.6 Definitions and Terminology
Data transfer interval
The time during which data is transferred from DOUT to DIN. The interval is 16 shift clocks
and the data transfer is initiated by the falling edge of the FS signal.
Signal data
This refers to the input signal and all of the converted representations through the ADC
channel, and the signal through the DAC channel to the analog output. This is in contrast
with the purely-digital software control data.
Primary
communication
Primary communication refers to the digital data-transfer interval. Since the device is synchronous, the signal data words from the ADC channel and to the DAC channel occur simultaneously.
Secondary
communication
Secondary communication refers to the digital control and configuration data-transfer interval into DIN, and the register read-data cycle from DOUT. The data transfer occurs when
requested by hardware or software.
SPI
Serial peripheral interface
Frame/pulse sync
Frame/pulse sync refers only to the falling edge of the signal FS that initiates the datatransfer interval. The primary FS starts the primary communication, and the secondary FS
starts the secondary communication.
Frame/pulse sync and Frame/Pulse sync and sampling period is the time between falling edges of successive
sampling period
primary FS signals and it is always equal to 256xSCLK if the number of cascading devices
is less than 5, or 512 xSCLK if the number of cascading devices is greater than 4.
fs
The sampling frequency
ADC channel
ADC channel refers to all signal-processing circuits between the analog input and the
digital conversion result at DOUT.
DAC channel
DAC channel refers to all signal-processing circuits between the digital data word applied
to DIN and the differential output analog signal available at OUTP and OUTM.
Host
A host is any processing system that interfaces to DIN, DOUT, SCLK, FS, and/or MCLK.
Dxx
Bit position in the primary data word (xx is the bit number).
DSxx
Bit position in the secondary data word (xx is the bit number).
d
The alpha character d represents valid programmed or default data in the control-register
format (see Section 3.2, Secondary Serial Communication) when discussing other data bit
portions of the register.
PGA
Programmable gain amplifier
FIR
Finite-duration impulse response
DCSI
Direct configuration serial interface for host control
1–6
1.7 Register Functional Summary
There are five control registers, which are used as follows:
Register 0 The no-op register. Addressing register 0 allows secondary-communication request without altering any
other registers.
Register 1 Control register 1. The data in this register has the following functions:
•
Produce the output flag to indicate a decimator FIR filter overflow (read cycle only)
•
Enable of general-purpose op-amps A1, A3, and A4
•
Enable/bypass ADC’s analog antialiasing filter
•
Select normal or auxiliary analog input
•
Control 16-bit or (15+1)-bit mode of DAC operation
•
Enable/bypass the decimator FIR filter
•
Enable/bypass the interpolator FIR filter
Register 2 Control register 2. The data in this register has the following functions:
•
Control of the low-power mode that converts data at the rate of 8 ksps
•
Control of the N-divide register that determines the filter clock rate and sample period
Register 3 Control register 3. The data in this register has the following functions:
•
Software reset and power down
•
Selection of analog loopback, digital loopback, and event monitor mode
•
Control of continuous data transfer mode
•
Control of the value of one-bit general-purpose output flag
•
Control the output of FLAG pin
•
Enable/disable ADC path
•
Enable/disable DAC path
•
Control of 16-bit or (15+1)-bit mode of ADC operation
Register 4 Control register 4. The data in this register has the following functions:
•
Control of the 4-bit gain of input amplifier
•
Control of the 4-bit gain of output amplifier
1–7
1–8
2 Functional Description
2.1 Device Functions
2.1.1
Operating Frequencies
The sampling frequency represented by the frequency of the primary communication is derived from the master clock
(MCLK) input with the following equation:
Fs = Sampling (conversion) frequency = MCLK/(256 × N), N = 1, 2..., 32
The inverse of the sampling frequency is the time between the falling edges of two successive primary frame-sync
signals. This time is the conversion period. For example, to set the conversion rate to 8 kHz, MCLK = 256 × N × 8000.
NOTE: The value of N is defined in control register 2 and its power-up value is 32.
2.1.2
ADC Signal Channel
Both IN (INP, INM) and AUX (AURXFP, AURXM) inputs can use the built-in antialiasing filter that can be bypassed
by writing a 1 to bit D5 of control register 1. The AUX input can also be connected to the general-purpose amplifier
A1 for general-purpose applications, such as electret-microphone interface and 2-to-4-wire hybrid interface, by
writing a 1 to bit D6 of control register 1. Bit D4 of control register 1 selects between IN or AUX for the ADC. The
selected input signal is amplified by the PGA and applied to the ADC input. The ADC converts the signal into
discrete-output digital words in 2s-complement data format, corresponding to the analog-signal value at sampling
time. These 16-bit (or 15-bit) digital words, representing sampled values of the analog input signal after PGA, are
clocked out of the serial port (DOUT) at the positive edge of SCLK during the frame-sync (FS) interval at the rate of
one bit for each SCLK and one word for each primary communication. During secondary communication, the data
previously programmed into the registers can be read out. If a register read is not required, all 16 bits are cleared to
0 in the secondary communication. This read operation is accomplished by sending the appropriate register address
(D11-D9) with the read bit (D12) set to 1 during present secondary communication. The timing sequence is shown
in Figures 2–1 and 2–2.
The decimation FIR filter can be bypassed by writing a 1 to bit D2 of control register 1. The whole ADC channel can
be turned off for power savings by writing 01 to bits D2 and D1 of control register 3.
0
1
15
……
SCLK
16
16 SCLKs
……
FS
DOUT
(16-bit)
D15
D14
……
D1
MSB
DOUT
(15+1-bit)
D15
D0
LSB
D14
……
D1
M/S
LSB
MSB
NOTES: A. M/S is used to indicate whether the 15-bit data comes from a master or a slave device (master: M/S=1, slave: M/S=0).
B. The MSB (D15) is stable (the host can latch the data in at this time) at the falling edging of SCLK number 0; the last bit (D0,M/S)
is stable at the falling edging of SCLK number 15.
Figure 2–1. Timing Sequence of ADC Channel (Primary Communication Only)
2–1
Primary
Secondary
16 SCLKs
16 SCLKs
16–bit ADC Data
M/S+ Register Data/
M/S+ All 0 (See Note A)
15–bit ADC Data + M/S
M/S+ Register Data/
M/S+ All 0 (See Note A)
Primary
FS
DOUT
(16-bit)
DOUT
(15+1-bit)
# SCLKs (See Note B)
# SCLKs Per Sampling Period (See Note C)
NOTES: A. M/S bit (D15) in the secondary communication is used to indicate whether the register data (address and content) come from a
master device or a slave device if read bit is set. Otherwise, it is all 0s except M/S bit (master: M/S=1, slave: M/S=0).
B. The number of SCLKs between FS (primary) and FS (secondary) is 128 if cascading devices are less than 5, or 256 if cascading
devices are greater than 4.
C. The number of SCLKs per data sampling period is 256 if cascading devices are less than 5, or 512 if cascading devices are greater
than 4.
Figure 2–2. Timing Sequence of ADC Channel (Primary and Secondary Communication)
2.1.3
DAC Signal Channel
DIN received the 16-bit serial data word (2s complement) from the host during the primary communication interval.
These 16-bit digital words, representing analog output signal before PGA, are clocked into the serial port (DIN) at
the falling edge of SCLK during the frame-sync interval, one bit for each SCLK and one word for each primary
communication interval. The data are converted to a pulse train by the sigma-delta DAC comprised of a
digital-interpolation filter and a digital 1-bit modulator. The output of the modulator is then passed to an internal
low-pass filter to complete the signal reconstruction. Finally, the resulting analog signal is applied to the input of a
programmable-gain amplifier is capable of differentially driving a 600-ohm load at OUTP and OUTM. The timing
sequence is shown in Figure 2–3.
During secondary communication, the digital control and configuration data, together with the register address, are
clocked in through DIN (see Appendix A for register map). These 16-bit data are used either to initialize the register
or read out register content through DOUT. If a register initialization is not required, a no-operation word (D15-D9 are
all set to 0) can be used. If D12 is set to 1, the content of the control register, specified by D7-D0, will be send out
through DOUT during the same secondary communication (see section 2.1.5). The timing sequence is shown in
Figure 2–4.
The interpolation FIR filter can be bypassed by writing a 1 to bit D1 of control register 1. The whole DAC channel can
be turned off for power savings by writing 10 to bits D2 and D1 of control register 3.
2–2
0
1
……
SCLK
15
14
16
16 SCLKs
……
FS
DIN
(16-bit)
D15
D14
……
D0
D1
MSB
DIN
(15+1-bit)
D15
LSB
D14
……
D1
D0=0
(see Note A)
MSB
LSB
NOTE A: d0 = 0 means no secondary-communication request (software secondary-request control, see Section 3.2).
Figure 2–3. Timing Sequence of DAC Channel (Primary Communication Only)
Primary
Secondary
16 SCLKs
16 SCLKs
16–bit DAC Data
Register Read/Write
15–bit DAC Data +
D0 = 1 (See Note B)
Register Read/Write
Primary
FS
DIN (16-bit)
(see Note A)
DIN
(15+1-bit)
# SCLKs Between
FS (Primary) and
FS (Secondary)
(see Note C)
# SCLKs Between Sampling Period (See Note D)
NOTES: A. FC has to be set high for a secondary communication request when 16-bit DAC data format is used (see Section 3.2).
B. D0 = 1 means secondary communication request (software secondary request control, see Section 3.2)
C. The number of SCLKs between FS (Primary) and FS (Secondary) is 128 if cascading devices are less than 5, or 256 if cascading
devices are greater than 4.
D. The number of SCLKs per data sampling period is 256 if cascading devices are less than 5, or 512 if cascading devices are greater
than 4.
Figure 2–4. Timing Sequence of DAC Channel (Primary and Secondary Communication)
2–3
2.1.4
MIC Input
The auxiliary inputs (AURXFP, AURXCP, and AURXM) can be programmed to interface with a microphone such as
an electret microphone, as illustrated in Figure 2–5, by writing a 1 to both bit D6 and bit D4 of control register 1.
TLV320AIC11
10 kΩ
0.1 µF
AURXFP
10 kΩ
AURXM
–
+
AURXCP
Electret
Microphone
S2D
AntiAliasing
Filter
20 kΩ
PGA
1 kΩ
MIC_BIAS
SigmaDelta
ADC
Vref
VMID
(a) Inverting Configuration
TLV320AIC11
10 kΩ
AURXFP
AURXM
AURXCP
Electret
Microphone
1 µF
–
+
S2D
20 kΩ
AVDD
AntiAliasing
Filter
10 kΩ
10 kΩ
1 kΩ
MIC_BIAS
VMID
(b) Noninverting Configuration
Figure 2–5. Typical Microphone Interface
2–4
PGA
SigmaDelta
ADC
Vref
2.1.5
Antialiasing Filter
The built-in antialiasing filter has a 3-dB cutoff frequency of 70 kHz.
2.1.6
Sigma-Delta ADC
The sigma-delta analog-to-digital converter is a sigma-delta modulator with 128× oversampling. The ADC provides
high-resolution, low-noise performance using oversampling techniques. Due to the oversampling employed, only
single-pole RC filters are required on the analog inputs.
2.1.7
Decimation Filter
The decimation filters reduce the digital data rate to the sampling rate. This is accomplished by decimating with a ratio
of 1:64. The output of the decimation filter is a 16-bit 2s-complement data word clocking at the sample rate selected
for that particular data channel. The BW of the filter is 0.45 × FS and scales linearly with the sample rate.
2.1.8
Sigma-Delta DAC
The sigma-delta digital-to-analog converter is a sigma-delta modulator with 128× oversampling. The DAC provides
high-resolution, low-noise performance using oversampling techniques.
2.1.9
Interpolation Filter
The interpolation filter resamples the digital data at a rate of 64 times the incoming sample rate. The high-speed data
output from the interpolation filter is then used in the sigma-delta DAC. The BW of the filter is 0.45 x FS and scales
linearly with the sample rate.
2.1.10 Analog and Digital Loopback
The analog and digital loopbacks provide a means of testing the modem data ADC/DAC channels and can be used
for in-circuit system level tests. The analog loopback routes the DAC low-pass filter output into the analog input where
it is then converted by the ADC to a digital word. The digital loopback routes the ADC output to the DAC input on the
device. Analog loopback is enabled by writing 01 to bits D7 and D6 respectively in control register 3. Digital loopback
is enabled by writing 10 to bits D7 and D6 in control register 3 (see Appendix A).
2.1.11 FIR Overflow Flag
The decimator FIR filter sets an overflow flag (bit D7) in control register 1 to indicate that the input analog signal has
exceeded the range of the internal decimation-filter calculations. When the FIR overflow flag has been set in the
register, it remains set until the register is read by the user. Reading this value resets the overflow flag.
If FIR overflow occurs, the input signal has to be attenuated either by the PGA or some other method.
2.1.12 Bypass Mode
An option is provided to bypass the FIR filter sections of the decimation and interpolation filters. This mode is selected
through bits D1 and D2 of control register 1, and effectively increases the frequency of FS signal to 4 times the normal
FIR-filter output rate. The sinc filters of the two paths can not be bypassed.
2–5
2.1.13 Automatic Cascading Detection (ACD)
The TLV320AIC11’s ACD makes cascade programming easy and supports the operation of up to 8 devices in
cascade. See Appendix A for register map description.
CLKOUT
DX
DR
(or Master Clock Source)
MCLK
DIN
FSX
FSR
CLKX
FS
DOUT
FSD
Master
SCLK M/S
CLKR
DVDD
MCLK
MCLK
MCLK
DIN
DIN
DIN
DOUT
DOUT
DOUT
FSD
FS
Slave 6
M/S
SCLK
FS
FS
FSD
Slave 0
M/S
SCLK
FSD
Slave 1
M/S
SCLK
TMS320UC54x
Figure 2–6. Cascading
2.1.14 Low-Power Mode
To select the low-power mode, in which the AIC11 typically consumes 39 mW, set bit D7 of control register 2 to 1 and
set the sampling rate at 8 ksps.
2.1.15 Event-Monitor Mode
This mode is only available during the register-write cycle, and is enabled by writing 11 to bits D6 and D7 of control
register 3. The event monitor mode is provided for applications that need hardware control and monitoring of external
events. By allowing the device to drive the FLAG terminal (set through bit D3 of the control register 3), the host DSP
is capable of system control through the same serial port that connects the device. Along with this control is the
capability of monitoring the value of the ALTIN terminal during a secondary communication cycle. One application
of this function is in monitoring RING DETECT or OFFHOOK DETECT from a phone-answering system. FLAG allows
response to these incoming control signals. Figure 2–7 shows the timing associated with this operating mode.
FS
Primary
DOUT
ALTDI
Secondary
16 bits
ÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ
NOTE A: When DIN performs a write operation (sets D12 to 0) during secondary communication.
Figure 2–7. Event Monitor Mode Timing
2–6
ÎÎÎÎÎ
ÎÎÎÎÎ
2.2 Reset and Power-Down Functions
2.2.1
Software and Hardware Reset
The TLV320AIC11 resets the internal counters and registers in response to either of two events:
•
A low-going reset pulse is applied to terminal RESET
•
A 1 is written to the programmable-software reset bit (D3 of control register 1)
Either event resets the control registers and clears all the sequential circuits in the device. Reset signals should be
at least 6 master-clock periods long, and it is recommended to synchronize the reset signal with the master clock in
master/slave cascade. For devices in cascade, it takes at least two FS cycles to apply software reset to all devices,
with the master being always programmed last.
2.2.2
Software and Hardware Power Down
With the exception of the digital interface, the device enters the power-down mode when D1 and D2 in control register
3 are set to 1. When PWRDWN is taken low, the entire device is powered down. In either case, the register contents
are preserved and the output of the monitor amplifier is held at the midpoint voltage to minimize pops and clicks.
The amount of power drawn during software power down is higher than it is during a hardware power down because
of the current required to keep the digital interface active. Additional differences between software and hardware
power-down modes are detailed in the following paragraphs. Figure 2–8 represents the internal power-down logic.
PWRDWN
Software Power Down
(For Control Register 3, D1 & D2)
D1 and D2 are
programmed through a
secondary write operation
Internal TLV320AIC11
Figure 2–8. Internal Power-Down Logic
2.2.2.1 Software Power Down
When D1 and D2 of control register 3 are set to 1, TLV320AIC11 enters the software power-down mode. In this state,
the digital-interface circuit is still active, while the internal ADC and DAC channels and differential outputs OUTP and
OUTM are disabled, and DOUT and FSD are inactive. Register data in secondary serial communications is still
accepted, but data in primary serial communications is ignored. The device returns to normal operation when D1 and
D2 of control register 3 are reset.
2.2.2.2 Hardware Power Down
When PWRDWN is held low, the device enters the hardware power-down mode. In this state, the internal-clock
control circuit and the differential outputs OUTP and OUTM are disabled. All other digital I/Os are either disabled, or
remain in the same state they were in immediately before power down. DIN can not accept any data input. The device
can only be returned to normal operation by taking and holding PWRDWN high. When not holding the device in the
hardware power-down mode, PWRDWN should be tied high.
2–7
2.3 Clock Source
MCLK is the external master-clock input. The clock circuit generates and distributes the necessary clocks throughout
the device. When the device is in the master mode, SCLK and FS are output and derived from MCLK in order to
provide clocking of the serial communications between the device and a DSP (digital signal processor). When in the
slave mode, SCLK and FS are all inputs. The SCLK can be connected to a faster clock source to speed up serial
communication between the slave and the master while the internal clock is maintained at 256 clocks per FS period
for internal processing. In SPI mode, the device is a slave and SCLK is connected to the SPICLK source.
2.4 Data Out (DOUT)
DOUT is placed in the high-impedance state after completing transmission of the LSB. In primary communication the
data word is the ADC conversion result. In secondary communication the data is the register read results when
requested by the read/write (R/W) bit. If a register read is not requested, the low eight bit of the secondary word is
all zeroes. The state of the master/slave (M/S) terminal is reflected by the MSB in secondary communication (DOUT,
bit D15), and by the LSB in primary communication (DOUT, bit D0).
2.4.1
Data Out, Master Mode
In the master mode, DOUT is taken from the high-impedance state by the falling edge of the master frame-sync (FS).
The most significant data bit then appears first on DOUT.
2.4.2
Data Out, Slave Mode
In the slave mode, DOUT is taken from the high-impedance state by the falling edge of the external frame-sync (FS).
The most significant data bit then appears first on DOUT.
2.5 Data In (DIN)
In a primary communication, the data word is the input digital signal to the DAC channel. If (15+1)-bit data format is
used, the LSB (D0) is used to request a secondary communication. In a secondary communication, the data is the
control and configuration data that sets the device for a particular function (see Section 3, Serial Communications).
The LSB of control register 1 determines whether it is a 15-bit or a 16-bit input.
2.6 FC (Hardware Secondary Communication Request)
The FC input provides for hardware requests for secondary communications. FC works in conjunction with the LSB
of the primary data word. FC should be tied low if not used.
2.7 Frame-Sync Function for TLV320AIC11
The frame-sync signal (FS) indicates the device is ready to send or receive data. FS is an output if the M/S pin is
connected to HI (master mode), and an input if the M/S pin is connected to LO (slave mode). The output FSD is a
delay version of the first frame-sync signal (FS) that is output 32 SCLKs after the first FS, and serves as the
frame-sync input to the next slave (see Figure 2–17). The data transferred out of DOUT and into DIN begins on the
falling edge of the FS signal. It can be configured as a frame or as a pulse signal, as determined by pins M0 and M1.
In normal operation, the digital serial interface consists of the shift clock (SCLK), the frame-sync signal (FS), the
ADC-channel data output (DOUT), and the DAC-channel data input (DIN). During the primary frame–synchronization
interval, SCLK clocks the ADC channel results out through DOUT, and clocks 16-bit/(15+1) DAC data in through DIN.
During the secondary frame-sync interval, SCLK clocks the register data out through DOUT in normal operation. If
the read bit (D12) is set to 1 and the device transfers control and device parameter in through DOUT. The timing
sequence is shown in Figures 2-1, 2-2, 2-3, and 2-4.
2–8
The TLV320AIC11 has three serial-interface modes that support most modern DSP engines. This modes can be
selected by M0 and M1. In mode 0 (Figure 2–9), FS is one-bit wide and it is active high one SCLK period before the
first bit (MSB) of each data transmission. In modes 1 (Figure 2–10) and 2 (Figure 2–11), the TLV320AIC11 operates
as a slave to interface with an SPI master in which FS is the SPISEL that determines the sampling rate. SCLK needs
to be free-running. In mode 3 (Figure 2–12), FS is low during data transmission into DIN and DOUT.
Table 2–1. Serial Interface Modes
MODE
M1
M0
0
0
0
Pulse mode
1
0
1
SPI_CP0 mode (SPI mode 0)
2
1
0
SPI_CP1 mode (SPI mode 1)
3
1
1
Frame mode
0
1
FRAME SYNC (FS) FORMAT
……
SCLK
15
14
16
16 SCLKs
……
FS
DIN/DOUT
(16-bit)
D14
D15
……
D1
D0
MSB
LSB
Figure 2–9. Timing Diagram for the FS Pulse Mode (M1M0 = 00)
0
1
……
SPICLK
(SCLK)
15
14
16 SCLKs
SPISEL
(FS)
DIN/DOUT
(16-bit)
……
D15
MSB
D14
……
D1
D0
LSB
Figure 2–10. Timing Diagram for the SPI_CP0 Mode (M1M0 = 01)
2–9
0
1
SPICLK
(SCLK)
15
14
……
16 SCLKs
SPISEL
(FS)
……
DIN/DOUT
(16-bit)
D14
D15
……
D1
D0
MSB
LSB
Figure 2–11. Timing Diagram for the SPI_CP1 Mode (M1M0 = 10)
0
1
……
SCLK
15
14
16
16 SCLKs
……
FS
DIN/DOUT
(16-bit)
D15
D14
……
MSB
D1
D0
LSB
Figure 2–12. Timing Diagram for the FS Frame Mode (M1M0 = 11)
NOTE: In frame mode, if AIC11 is in slave mode, DIN/DOUT should be delayed by one SCLK from the falling edge of FS.
2.7.1
Frame-Sync (FS) Function—Continuous-Transfer Mode (Master Only)
Writing a 1 to bit D5 of control register 3 enables the continuous-transfer mode. In this mode, the data bits are
transmitted and received contiguously with no inactivity between bits at the very next FS, and no further frame sync
FSs are generated. Secondary communication is not available. To disable the continuous transfer mode, use the
direct-configuration mode (See section 3.3) or reset the device.
2.7.2
Frame-Sync (FS) Function—Fast-Transfer Mode (Slave Only)
By connecting the fast clock to the SCLK pin, data can be transmitted and received at a higher rate than 256 x Fs
in the slave mode for a stand-alone AIC11.
2–10
2.7.3
Frame-Sync (FS) Function—Master Mode
The master mode in the TLV320AIC11 is selected by connecting pin M/S pin to HI. In the master mode, the
TLV320AIC11 generates the frame-sync signal (FS) to the DSP that goes low on the rising edge of SCLK and remains
low during a 16-bit data transfer.
16 SCLKs
16 SCLKs
FS
(see Note A)
Primary
Secondary
Primary
FS
(see Note B)
Primary
Secondary
Primary
DIN/DOUT
NOTES: A. Primary and secondary serial communications
B. Primary serial communication only
Figure 2–13. Master Device Frame-Sync Signal With Primary and Secondary Communication ( No Slaves)
2.7.4
Frame-Sync (FS) Function—Slave Mode
The slave mode is selected by connecting pin M/S to LO. The frame-sync timing is generated externally by the master,
as shown in Figure 2–14 (that is, FSD) and is applied to FS of the slave to control the ADC and DAC timing.
FS
(Master to DSP)
MP
SP
MS
SS
MP
FSD (Master)
to FS (Slave)
32 SCLKs
NOTE: MP: master primary (master-device data is transferred during this period, the DOUT of the slave device is in high-impedance state).
SP: slave primary (slave device data is transferred during this period, the DOUT of master device is in high-impedance state).
MS: master secondary (master device control register information is transferred during this period, the DOUT of slave device is in highimpedance state).
SS: slave secondary (slave device control register information is transferred during this period, the DOUT of master device is in highimpedance state).
Figure 2–14. Master Device’s FS Output to DSP and FSD Output to the Slave
2–11
2.7.5
Frame-Sync Delayed (FSD) Function, Cascade Mode
In cascade mode, the DSP must be able to identify the master and slaves according to the register map shown in
Appendix A. Each device in the cascade contains a 3-bit cascade register (D15-D13 in the register address) that has
been programmed by the ACD (automatic cascade detection) with an address value equal to its position in the
cascade during the device’s power-up initialization (see Section 2.1.11). The device address of the master is always
equal to the number of slaves in the cascade. For example, in Figure 2–15, D15-D13 of the master will be 011, as
shown in row 4 of Table A-1 (Appendix A). The DSP receives all frame-sync pulses from the master though the
master’s FS. The master FSD is output to the first slave, and the first slave FSD is output to the second slave device,
and so on. Figure 2–15 shows the cascade of 4 TLV320AIC11s in which the closest one to the DSP is the master,
and the rest are slaves. The FSD output of each device is input to the FS terminal of the succeeding device.
Figure 2–16 shows the FSD timing sequence in the cascade.
(or Master Clock Source)
CLKOUT
DX
DR
MCLK
DIN
FSX
FSR
FS
DOUT
FSD
Master
SCLK M/S
CLKX
DVDD
CLKR
MCLK
MCLK
MCLK
DIN
DIN
DIN
DOUT
DOUT
DOUT
FS
FSD
Slave 2
M/S
SCLK
FS
FSD
FS
Slave 0
M/S
SCLK
FSD
Slave 1
M/S
SCLK
TMS320UC54x
Figure 2–15. Cascade Mode Connection (to DSP Interface)
Master FS
P
P
P
P
S
S
M
S2
S1
S0
M
S2
Master FSD,
Slave 2 FS
32 SCLKs
Slave 2 FSD,
Slave 1 FS
32 SCLKs
Slave 1 FSD,
Slave 0 FS
32 SCLKs
Slave 0 FSD
(See Note)
32 SCLKs
NOTE: Slave 0 FSD should be left open.
Figure 2–16. Master-Slave Frame-Sync Timing
2–12
S
2.8 Multiplexed Analog Input and Output
The two differential analog inputs (INP and INM, or AUXP and AUXM) are multiplexed into the sigma-delta modulator.
The performance of the AUX channel is similar to the normal-input channel. The gain of the input amplifiers is set
through control register 4.
2.8.1
Multiplexed Analog Input
To produce excellent common-mode rejection of unwanted-signal performance, the analog signal is processed
differentially until it is converted to digital data. The signal applied to the INM and INP terminals should be differential
to preserve the device specifications. The signal source driving the analog inputs (INP and INM, or AUXP and AUXM)
should have a low source impedance to attain the lowest noise performance and accuracy. To obtain maximum
dynamic range, the signal should be ac-coupled to the input terminal. The analog input signal is self-biased to the
mid-supply. Bits D3 and D4 of control register 1 select these input sources. The default condition self-biases the input,
since the register default value selects INP and INM as the sources for the ADC.
INP
VINP
2.5 V
(or ) 1.5 V
INM
VINM
TLV320AIC11
Figure 2–17. INP and INM Internal Self-Biased Circuit (2.5 V for 5-V Operation and 1.5 V for 3-V Operation)
2.8.2
Analog Output
OUTP and OUTM are differential outputs and can typically drive a 600-ohm load directly. Figure 2–18 shows the
circuit when the load is ground-referenced.
10 k Ω
+5 V
10 kΩ
–
OUTM
+
10 kΩ
OUTP
–5 V
TLE2062
Load
10 kΩ
Figure 2–18. Differential Output Drive (Ground-Referenced)
2–13
2.8.3
Single-Ended Analog Input
The two differential inputs (INP and INM, or AUXP and AUXM) can be configured to work as single-ended inputs by
connecting INP or AUXP to the analog input, and INM or AUXM to the external common-mode input. This is illustrated
in Figure 2–19.
C
100 Ω
Analog Input
INP
Common-Mode Input
INM
Figure 2–19. Single-Ended Input
2.8.4
Single-Ended Analog Output
The differential output of TLV320AIC11 can be configured as a single-ended output. This is illustrated in Figure 2–20.
C
OUTP
RL
OUTM
Figure 2–20. Single-Ended Output
2–14
3 Serial Communications
DOUT, DIN, SCLK, SXCLK, FS, and FC are the serial communication signals. SCLK is used to perform internal
processing and data transfer for serial interface between AIC11 and DSP. In the pulse/frame FS mode, there are 256
SCLKs per sampling period (512 if there are more than 4 devices in cascade). The digital-output data for the ADC
is taken from DOUT. The digital-input data for the DAC is applied to DIN. The synchronization clock for the serial
communication data and the frame-sync is taken from SCLK. The frame-sync signal that starts the ADC and DAC
data-transfer interval is taken from FS. Primary serial communication is used for signal data transmitted from the ADC
or to the DAC. Secondary communication is used to read or write words that control both the options and the circuit
configurations of the device.
The purpose of the primary and secondary communications is to allow conversion data and control data to be
transferred across the same serial port. A primary transfer is always dedicated to conversion data. A secondary
transfer or an asynchronous communication is used to set up and/or read the register values. A primary transfer
occurs for every conversion period. A secondary transfer occurs only when requested. Secondary serial
communication can be requested either by hardware (FC terminal) or by software (D0 of primary data input to DIN).
The direct configuration mode uses pin DCSI to program control registers instantly.
3.1 Primary Serial Communication
Primary serial communication is used to transmit and receive conversion signal data. The DAC word length depends
on the states of bit D0 in control register 1. After power up or reset, the device defaults to 15-bit mode. When the DAC
word length is 15 bits, the last bit of the primary 16-bit serial communication word is a control bit used to request
secondary serial communication. In the 16-bit mode, all 16 bits of the primary-communication word are used as data
for the DAC, and the hardware terminal FC must be used to request secondary communication.
Figure 3–1 shows the timing relationship for SCLK, FS, DOUT, and DIN in a primary communication. The timing
sequence for this operation is as follows:
•
FS is brought low by the TLV320AIC11.
•
A 16-bit word is transmitted from the ADC (DOUT), and then a 16-bit word is received from the DAC (DIN).
SCLK
FS
DIN
D15 D14 D13 D12 D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DOUT
D15 D14 D13 D12 D11 D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Figure 3–1. Primary Serial Communication Timing
3–1
3.2 Secondary Serial Communication
Secondary serial communication is used to read or write 16-bit words that program both the options and the circuit
configurations of the device. Register programming always occurs during secondary communication. Four primary
and secondary communication cycles are requested to program the four registers. If the default value for a particular
register is desired, then the register addressing can be omitted during secondary communications. The NOOP
command addresses a pseudo-register (register 0), and no register programming takes place during this secondary
communication. If secondary communication is desired for any device (either master or slave), then a secondary
communication must be requested for all devices, starting with the master. This results in a secondary frame-sync
(FS) for all devices. The NOOP command can be used for devices that do not need a secondary operation.
During a secondary communication, a register can be written to or read from. When writing to a register, DIN contains
the value to be written. The data returned on DOUT is + 0000000000000 (3-bit device address).
There are two methods of initiating a secondary communication, as illustrated in Figure 3–2:
•
Asserting a high level on FC (hardware request)
•
Asserting the LSB of the DIN 16-bit serial communication high while in the 15-bit mode (software request)
NOTE:
The secondary communication request should not be asserted during the first two samples
after power up.
FC
(Hardware)
Secondary Request
(LSB of DIN)
16-Bit Mode
(Control 1 Register, D0)
Internal TLV320AIC11
Figure 3–2. Hardware and Software Secondary Communication Request
Pulling FC high causes the start of the secondary communication’s 128 or 256 SCLKs (see Figures 2–2 and 2–4)
after the start of the primary communication frame, depending on the number of devices in cascade.
The second method to initiate a secondary communication is asserting the LSB high. A software request is typically
used when the request resolution of the DAC channel is less than 16 bits. Then the least significant bit (D0) can be
used for secondary requests, as shown in Table 3–1. The request is made by placing the device in the 15-bit DAC
mode and making the LSB of DIN high. All devices should be in 15-bit DAC mode, and secondary communication
should be requested for all devices.
Table 3–1. Least Significant Bit Control Function
3–2
CONTROL BIT D0
CONTROL BIT FUNCTION
0
No operation (NOOP)
1
Secondary communication request
3.2.1
Register Programming
All register programming occurs during secondary communication through DIN or ALTI, and data are latched and
valid on the falling edge of the SCLK during the frame-sync signal. If the default value of a particular register is desired,
that register does not need to be addressed during the secondary communication interval. The no-op command
(DS15-DS8 all set to 0) addresses the pseudo-register (register 0), and no register programming takes place during
the communication.
In addition, each register can be read back through DOUT during secondary communications by setting the read bit
(D12) to 1. When a register is in the read mode, no data can be written to the register during this cycle. A subsequent
secondary communication is required to return this register to the write mode.
For example, if the contents of control register 1 of device 3 are desired to be read out from DOUT, the following
procedure must be performed through DIN:
•
Request secondary communication by setting either D0 = 1(software request), or FC = high (hardware
request) during the primary communication interval.
•
During the secondary communication interval (FS), send data in through DIN using the following format:
Device Address
0
1
1
RW
1
Register Address
X
0
x
0
1
Register Content
x
x
x
x
x
x
x
DS15
•
Then, during the same frame, the following data will be read from DOUT; the last 8 bits of DOUT will contain
register 1 data.
Device Address
0
x
DS0
1
1
RW
x
Register Address
X
x
x
x
x
Register Content
d
d
d
d
d
d
d
DS15
d
DS0
Figure 3–3 is the timing diagram of this procedure.
FS
DIN
P
S
Register 1 Read
DOUT
Low 8 Bit (D0 – D7) is
the content of register 1
Figure 3–3. Device 3/Register 1 Read Operation Timing Diagram
3–3
To program control register 1, the following procedure must be performed through DIN:
•
Request secondary communication by setting either D0=1(software request), or FC = high (hardware
request) during the primary communication interval.
•
At the secondary communication interval (FS), send data in the following format through DIN:
Device Address
0
1
RW
1
0
Register Address
X
0
x
0
1
Register Content
d
d
d
d
d
d
d
DS15
d
DS0
•
The following is the data out of DOUT.
Device Address
0
1
RW
1
0
Register Address
X
x
x
x
x
Register Content
0
0
0
0
0
0
0
DS15
0
DS0
Figure 3–4 is the timing diagram of this procedure.
FS
P
S
DIN
Register Write
DOUT
(Device Addr) + All 0
Figure 3–4. Device 3/Register 1 Write Operation Timing Diagram
3.2.2
Hardware Secondary Serial Communication Request
A secondary communication can be requested by asserting an FC pulse that sets an internal flag. This flag will be
reset as soon as the programming of control registers is finished. Thus, one FC pulse needs to be asserted per
secondary communication request. Figures 3–5 and 3–6 show the FS output from a master device.
FS
Primary
Secondary
Primary
Secondary
Request
No Secondary
Request
FC
DOUT
DIN
ADC Data Out
Register
Read/Write
ADC Data Out
DAC Data In
Register
Read/Write
DAC Data In
Figure 3–5. FS Output When Hardware Secondary Serial Communication
Is Requested Only Once (No Slave)
3–4
P
P
Master FS
M
P
S2
P
S1
S
S0
S
M
S
S2
S
S1
P
S0
M
FC pulse needs to be inserted any time
within the primary communication
FC
(See Note)
NOTES: A. FC of master device and slave devices should be connected together
B. Primary communication interval = 256 SCLKs if cascading devices < 5
C. Primary communication interval = 512 SCLKs if cascading devices > 4
Figure 3–6. Output When Hardware Secondary Serial Communication Is Requested (Three Slaves)
3.2.3
Software Secondary Serial Communication Request
The LSB of the DAC data within a primary transfer can request a secondary communication through bit D0 of control
register 1 when the device is in the 15-bit mode.
For all serial communications, the most significant bit is transferred first. For a 16-bit ADC word and a 16-bit DAC word,
D15 is the most significant bit and D0 is the least significant bit. For a 15-bit DAC data word in a primary
communication, D15 is the most significant bit, D1 is the least significant bit. Bit D0 is then used for the secondary
communication request control. All digital data values are in 2s-complement data format (see Figure 3–7).
If the data format is set to 16-bit word, all 16 bits are either ADC or DAC data, and secondary communication can
only be requested by hardware (FC terminal), or control registers can be programmed by the direct configuration
mode.
FS
P
DIN
Data (D0 = 1)
Secondary
Communication Request
S
Register
Read/Write
P
Data (D0 = 0)
No Secondary
Communication Request
Figure 3–7. FS Output During Software Secondary Serial Communication Request (No Slave)
3–5
3.3 Direct Configuration Mode
For DSP applications that use continuous data transfer mode for autobuffering, or for DMA operations that do not
have the capability to interfere with the data conversion channel by inserting the secondary communication, the
TLV320AIC11’s direct-configuration mode provides a flexible alternative to programming control registers through
pin DCSI. The serial input to DCSI should normally be in a high state, start its valid data with a start bit of logic low,
and pull high as a stop bit after transmission of the LSB. DCSI requires a pullup resistor for 3-state input. The AIC11
registers data bits on the falling edge of SCLK. Figure 3–8 shows a typical connection between the TMS320C54x
and the AIC11 using DCSI for direct configuration of control registers. Figure 3–9 shows the timing diagram for the
direct configuration mode.
DVDD
1 kΩ
CLKX0
DX0
DCSI
DCSI
FSX1
M/S
FSR1
FS
M/S
DVDD
FSD
DGND
FS
DX1
DIN
DIN
DR1
DOUT
DOUT
SCLK
SCLK
CLKX1
CLKR1
TMS320UC54x
TLV320AIC11
TLV320AIC11
Figure 3–8. Direct Configuration
SCLK
D15 D14 D13 D12 D11 D10 D9
DCSI
Start Bit = 0
Device
Address
D8
D7
D6
Register
Address
D5
D4
D3
D2
D1
D0
Register Data
Stop Bit = 1
Figure 3–9. Direct Configuration Mode Timing
To program control register 1 of device 3, send data in with the following format through DCSI:
SB
0
D15
3–6
Device Address
0
1
1
Register Address
X
0
x
0
1
Register Content
x
x
x
x
x
x
x
x
D0
3.4 Continuous Data Transfer Mode
In continuous data transfer mode, the 16-bit converter data are transferred contiguously with no inactivity between
bits. This mode is available in the stand-alone master with M1M0 = 00 (FS-pulse mode) and selected by setting bit
D5 of control register 3 to 1. The frame sync pulse overlaps the last bit transmitted in the previous 16 bits of data.
The secondary communication request is not allowed in this mode and therefore the direct configuration mode should
be used to program the internal control registers. The continuous data transfer mode is designed to support the TI
DSP McBSP’s autobuffering unit (ABU) operation in which serial port interrupts are not generated with each word
transferred to prevent CPU’s ISR overheads.
SCLK
FS
DIN
C0
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
E15
E14
E13
E12
DOUT
C0
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
E15
E14
E13
E12
Figure 3–10. Continuous Data Transfer Mode Timing
3–7
3.5 DIN and DOUT Data Format
3.5.1
Primary Serial Communication DIN and DOUT Data Format
DIN
(15 + 1)-Bit Mode
D15 – D1
D0
A/D & D/A Data
DOUT
(15 + 1)-Bit Mode
Secondary
Communication
Request
D0
D15 – D1
M/S Bit
DIN
16-Bit Mode
D15 – D0
A/D & D/A Data
DOUT
16-Bit Mode
D15 – D0
Figure 3–11. Primary Communication DIN and DOUT Data Format
3.5.2
Secondary Serial Communication DIN and DOUT Data Format
DIN (Read)
D15
D14
D13
Device Address
DIN (Write)
D15
D14
D13
1
R/W
0
D11
D10
D9
Reserved
Don’t Care
D8
D7 – D0
Data to the
Register
Register Address
D11
D10
D9
D8
Device Address
DOUT (Read)
D15
D14
D13
D7 – D0
Register Data
X
X
X
X
D8
D7 – D0
Figure 3–12. Secondary Communication DIN and DOUT Data Format
3.5.3
Direct Configuration DCSI Data Format
Device Address
DCSI (Write)
0
D14
D13
D12
Data to the
Register
Register Address
D11
D10
D9
D8
D7 – D0
Figure 3–13. Direct Communication DCSI Data Format
3–8
4 Specifications
4.1 Absolute Maximum Ratings Over Operating Free-Air Temperature Range
(Unless Otherwise Noted)†
Supply voltage I/O range, DVDD1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4.0 V
Supply voltage core range, DVDD2, AVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 7 V
Output voltage range, all digital output signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 4.5 V
Input voltage range, all digital input signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 4.5 V
Case temperature for 10 seconds: package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
4.2 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
Analog Supply voltage, AVDD
3
5.5
V
Digital Supply voltage, DVDD
3
5.5
V
Supply voltage, I/O,, DVDD1 (5-V and 3-V operation)
1.1
1.8
3.6
V
Supply voltage,, DVDD2 (3-V operation)
3
3.3
3.6
V
Supply voltage,, DVDD2 (5-V operation)
4.5
5
5.5
V
Supply voltage, AVDD1 and AVDD2 (3-V operation)
3
3.3
3.6
V
Supply voltage, AVDD1, and AVDD2 (5-V operation)
4.5
5
5.5
V
0
3
V
0
2
Analog signal peak-to-peak input voltage, VI(analog) (5 V supply), single-ended.
Analog signal peak-to-peak input voltage, VI(analog) (3.3 V supply), single-ended.
Differential output load resistance, RL
V
Ω
600
Output load capacitance, CL
Master clock
10
ADC or DAC conversion rate
Operating free-air temperature, TA
–40
20
pF
15
MHz
22
kHz
85
°C
4.3 Electrical Characteristics Over Recommended Operating Free-Air Temperature
Range, AVDD1 = 3.3 V, AVDD2 = 3.3 V, DVDD1 = 1.1 V, DVDD2 = 3.3 V
4.3.1
Digital Inputs and Outputs, Fs = 8 kHz, Output Not Loaded
PARAMETER
TEST CONDITIONS
IO = -360 µA
IO = 2 mA
MIN
TYP
DVDD1 × 0.8
MAX
UNIT
VOH
VOL
High-level output voltage, DOUT
IIH
IIL
High-level input current, any digital input
Ci
Input capacitance
10
pF
Co
Output capacitance
10
pF
Low-level output voltage, DOUT
Low-level input current, any digital input
DVSS–0.3
VIH = 0.99 V
VIL = 0.11 V
DVDD1+0.3
DVDD1 × 0.2
V
10
µA
10
µA
V
4–1
4.3.2
ADC Path Filter, Fs = 8 kHz (see Note 2)
PARAMETER
Filter gain relative to gain at 1020 Hz
TEST CONDITIONS
MIN
TYP
MAX
0 Hz to 300 Hz
–0.5
0.2
300 Hz to 3 kHz
–0.5
0.25
3.3 kHz
–0.5
0.3
3.6 kHz
–3
4 kHz
–35
≥ 4.4 kHz
–74
UNIT
dB
NOTE 2: The filter gain outside of the passband is measured with respect to the gain at 1024 Hz. The analog input test signal is a sine wave with
0 dB = 4 VI(PP) as the reference level for the analog input signal. The pass band is 0 to 3600 Hz for an 8-kHz sample rate. This pass
band scales linearly with the sample rate.
4.3.3
ADC Dynamic Performance, Fs = 8 kHz
4.3.3.1 ADC Signal-to-Noise (see Note 3)
PARAMETER
SNR
Signal to noise ratio
Signal-to-noise
MIN
TYP
VI = –1 dB
VI = –3 dB
TEST CONDITIONS
75
84
75
83
VI = –9 dB
VI = –40 dB
70
78
40
47
MAX
UNIT
dB
NOTE 3: The test condition is a 1020-Hz input signal with an 8-kHz conversion rate. Input and output common mode is 2.5 V for 5-V supply, and
1.5-V for 3.3-V supply.
4.3.3.2 ADC Signal-to-Distortion (see Note 3)
PARAMETER
THD
Signal to total harmonic distortion
Signal-to-total
MIN
TYP
VI = –1 dB
VI = –3 dB
TEST CONDITIONS
72
83
70
84
VI = –9 dB
VI = –40 dB
75
88
60
76
MAX
UNIT
dB
NOTE 3: The test condition is a 1020-Hz input signal with an 8-kHz conversion rate. Input and output common mode is 2.5 V for 5-V supply, and
1.5-V for 3.3-V supply.
4.3.3.3 ADC Signal-to-Distortion + Noise (see Note 3)
PARAMETER
THD+N
Signal to total harmonic distortion + noise
Signal-to-total
MIN
TYP
VI = –1 dB
VI = –3 dB
TEST CONDITIONS
72
80
70
80
VI = –9 dB
VI = –40 dB
70
78
40
47
MAX
UNIT
dB
NOTE 3: The test condition is a 1020-Hz input signal with an 8-kHz conversion rate. Input and output common mode is 2.5 V for 5-V supply, and
1.5-V for 3.3-V supply.
4–2
4.3.4
ADC Channel Characteristics
PARAMETER
VI(PP)
Peak to peak input voltage (differential)
Peak-to-peak
TEST CONDITIONS
AVDD = 5 V
AVDD = 3 V
Dynamic range
MIN
Preamp gain = 0 dB
4
VI = –3 dB
Gain error
CMRR
Common-mode rejection ratio at INM, INP or AUXM, AUXP
Rj
VI = –1 dB at 1020 Hz
UNIT
V
84
dB
100
dB
0.1
dB
±11
mV
70
dB
Idle channel noise (on-chip reference)
VI = –1 dB at 1020 Hz
VINP,INM = 0 V
20
µVrms
Input resistance
TA = 25°C
35
kΩ
ADC converter offset error
Channel delay
4.3.5
MAX
6
Interchannel isolation
EG
EO(ADC)
TYP
Preamp gain = 0 dB
17/fs
s
DAC Path Filter, Fs = 8 kHz (see Note 4)
PARAMETER
Filter gain relative to gain at 1020 Hz
TEST CONDITIONS
MIN
TYP
MAX
0 Hz to 300 Hz
–0.5
0.2
300 Hz to 3 kHz
–0.25
0.25
–1
0.3
3.3 kHz
3.6 kHz
–3
4 kHz
–35
≥ 4.4 kHz
–74
UNIT
dB
NOTE 4: The filter gain outside of the passband is measured with respect to the gain at 1020 Hz. The input signal is the digital equivalent of a
sine wave (digital full scale = 0 dB). The nominal differential DAC channel output with this input condition is 4 VI(PP). The pass band
is 0 to 3600 Hz for an 8-kHz sample rate. This pass band scales linearly with the conversion rate.
4.3.6
DAC Dynamic Performance
4.3.6.1 DAC Signal-to-Noise When Load is 600 Ω (see Note 5)
PARAMETER
SNR
Signal to noise ratio
Signal-to-noise
TEST CONDITIONS
MIN
TYP
VI = 0 dB
VI = –3 dB
75
85
75
83
VI = –9 dB
VI = –40 dB
70
77
40
47
MAX
UNIT
dB
NOTE 5: The test condition is the digital equivalent of a 1020 Hz input signal with an 8-kHz conversion rate. The test is measured at output of
application schematic low-pass filter. The test is conducted in 16-bit mode.
4.3.6.2 DAC Signal-to-Distortion When Load is 600 Ω (see Note 5)
PARAMETER
THD
Signal to total harmonic distortion
Signal-to-total
TEST CONDITIONS
MIN
TYP
VI = 0 dB
VI = –3 dB
70
80
70
80
VI = –9 dB
VI = –40 dB
75
83
60
74
MAX
UNIT
dB
NOTE 5: The test condition is the digital equivalent of a 1020 Hz input signal with an 8-kHz conversion rate. The test is measured at output of
application schematic low-pass filter. The test is conducted in 16-bit mode.
4–3
4.3.6.3 DAC Signal-to-Distortion + Noise When Load is 600 Ω (see Note 5)
PARAMETER
THD+N
TEST CONDITIONS
Signal to total harmonic distortion + noise
Signal-to-total
MIN
TYP
VI = 0 dB
VI = –3 dB
70
79
70
78
VI = –9 dB
VI = –40 dB
70
77
40
47
MAX
UNIT
dB
NOTE 5: The test condition is the digital equivalent of a 1020 Hz input signal with an 8-kHz conversion rate. The test is measured at output of
application schematic low-pass filter. The test is conducted in 16-bit mode.
4.3.7
DAC Channel Characteristics
PARAMETER
TEST CONDITIONS
Dynamic range
MIN
TYP
VI = 0 dB at 1020 Hz
Interchannel isolation
EG
VOO
VO
Gain error, 0 dB
Idle channel narrow band noise
VO = 0 dB at 1020 Hz
0 kHz to 4 kHz, See Note 6
Output offset voltage at OUT (differential)
DIN = all zeros
Analog output voltage
AVDD = 5 V
AVDD = 3.0 V
MAX
dB
100
dB
0.1
dB
20
µVrms
±10
Differential with respect to common mode
and full-scale digital input
mV
–4
4
–2.5
2.5
Channel delay
UNIT
85
V
18/fs
NOTE 6: The conversion rate is 8 kHz.
4.3.8
Op-Amp Interface (A1, A3, A4)
PARAMETER
AV
TEST CONDITIONS
MIN
TYP
MAX
Gain
UNIT
100
Input voltage range
0.5
AVDD – 0.5
10
Input offset voltage
Input offset current
Output power
V
mV
0
mA
15
mW
dB
SNR
Signal-to-noise ratio
Input frequency = 1020 Hz
91
THD + N
Signal-to-total harmonic distortion + noise
Input frequency = 1020 Hz
87
dB
Unity-gain bandwidth
Open loop
10
MHz
30
µVrms
Noise output voltage
4.3.9
Op-Amp Interface (A1, A3, A4)
PARAMETER
TEST CONDITIONS
MIN
Output power
TYP
MAX
UNIT
15
mW
dB
SNR
Signal-to-noise ratio
Input frequency = 1020 Hz
90
THD + N
Signal-to-total harmonic distortion + noise
Input frequency = 1020 Hz
90
dB
Unity-gain bandwidth
Open loop
10
MHz
30
µVrms
Noise output voltage
4.3.10 Power-Supply Rejection (see Note 7)
PARAMETER
AVDD
DVDD
Supply voltage rejection ratio
Supply-voltage
Supply voltage rejection ratio
Supply-voltage
TEST CONDITIONS
DAC channel
ADC channel
DAC channel
ADC channel
fi = 0 to 30 kHz
fi = 0 to 30 kHz
MIN
TYP
MAX
UNIT
90
77
dB
90
84
NOTE 7: Power supply rejection measurements are made with both the ADC and the DAC channels idle and a 100 mV peak-to-peak signal
applied to the appropriate supply.
4–4
4.3.11 Power Supply
4.3.11.1 Low-Power Mode (set control register bit D7 to 1)
PARAMETER
PD
IDD
TEST CONDITIONS
Power dissipation
Supply current
MIN
All sections on
TYP
MAX
39
Analog
All sections on, AVDD1 = 3.3 V, AVDD2 = 3.3 V
10.5
Digital
All sections on, DVDD2 = 3.3 V, DVDD1 = 1.1 V
2.1
UNIT
mW
mA
4.3.11.2 Normal Operation
PARAMETER
PD
TEST CONDITIONS
Power dissipation
All sections on
Analog
IDD
MIN
Supply current
Digital
All sections on, AVDD1 = 3.3 V, AVDD2 = 3.3 V
Power down,
AVDD1 = 3.3 V, AVDD2 = 3.3 V
All sections on, DVDD1 = 1.1 V, DVDD2 = 3.3 V
Power down,
DVDD1 = 1.1 V, DVDD2 = 3.3 V
TYP
MAX
UNIT
49
mW
13.6
mA
4
µA
1
mA
81
µA
4.4 Timing Requirements (see Parameter Measurement Information)
4.4.1
Master Mode Timing Requirements
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX
UNIT
td1
td2
Delay time, SCLK↑ to FS↓
tsu1
th1
Setup time, DIN, before SCLK low
ten1
tdis1
td3
td(CH-FDL)
Delay time, MCLK↓ to SCLK↑
twH
twL
Pulse duration, MCLK high
12.5
ns
Pulse duration, MCLK low
12.5
ns
4.4.2
Delay time, SCLK↑ to DOUT
5
ns
15
ns
5
ns
Hold time, DIN, after SCLK high
1/2T+5
ns
Enable time, FS↓ to DOUT
1/2T+5
Disable time, FS↑ to DOUT Hi-Z
CL = 20 pF
ns
5
Delay time, SCLK high to FSD low (see Figure 5–1)
ns
10
ns
5
ns
Slave Mode Timing Requirements
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX
UNIT
td4
td5
Delay time, SCLK↑ to FS↓
tsu2
th2
Setup time, DIN, before SCLK low
Hold time, DIN, after SCLK high
1/2T+5
ten2
tdis2
Enable time, FS↓ to DOUT
1/2T+5
td6
td(FL-FDL)
Delay time, MCLK↓ to SCLK↑
td(CH-FDL)
twH
Pulse duration, MCLK high
12.5
ns
twL
Pulse duration, MCLK low
12.5
ns
Delay time, SCLK↑ to DOUT
Disable time, FS↑ to DOUT Hi-Z
5
ns
15
ns
5
CL = 20 pF
ns
ns
25
5
ns
ns
10
ns
Delay time, FS low to FSD low (see Figure 5–2)
5
ns
Delay time, SCLK high to FSD low (see Figure 5–1)
5
ns
4–5
4–6
5 Parameter Measurement Information
DVDD1 × 0.8 V
SCLK
td(CH–FL)
FS/FSD
DVDD1 × 0.2 V
Figure 5–1. FS and FSD Timing
td3
twH
MCLK
twL
SCLK
td2
td1
FS
tdls
ten1
DOUT
D15
D14
tsu1
DIN
D15
D14
th1
Figure 5–2. Serial Communication Timing
5–1
AMPLITUDE
vs
FREQUENCY
0
Fs = 8 kHz
Input = –3 dB
Amplitude – dB
–30
–60
–90
–120
–150
0
500
1000
1500
2000
2500
3000
3500
4000
f – Frequency – Hz
Figure 5–3. FFT–ADC Channel, Fs = 8 kHz, Input = –3 dB
AMPLITUDE
vs
FREQUENCY
0
Fs = 8 kHz
Input = –3 dB
Amplitude – dB
–30
–60
–90
–120
–150
0
500
1000
1500
2000
2500
3000
3500
f – Frequency – Hz
Figure 5–4. FFT–DAC Channel, Fs = 8 kHz, Input = –3 dB
5–2
4000
AMPLITUDE
vs
FREQUENCY
0
Fs = 8 kHz
Input = –1 dB
Amplitude – dB
–30
–60
–90
–120
–150
0
500
1000
1500
2000
2500
3000
3500
4000
f – Frequency – Hz
Figure 5–5. FFT–ADC Channel, Fs = 8 kHz, Input = –1 dB
AMPLITUDE
vs
FREQUENCY
0
Fs = 8 kHz
Input = 0 dB
Amplitude – dB
–30
–60
–90
–120
–150
0
500
1000
1500
2000
2500
3000
3500
4000
f – Frequency – Hz
Figure 5–6. FFT–DAC Channel, Fs = 8 kHz, Input = 0 dB
5–3
5–4
6 Mechanical Information
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
0°– 7°
1,05
0,95
Seating Plane
1,20 MAX
0,75
0,45
0,08
4073176 / B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
6–1
6–2
Appendix A
Register Set
Bits D15 through D13 represent the device address in the cascade set by the automatic cascade detection described
in Section 2.1.13. In cascading, the master is the device directly connected to the DSP. For example, if there are 4
devices in the cascade, as shown in row 4 of Table A-1 and in Section 2.7.5, the device address D15-D13 of the master
will have a binary value of 011. The other three slaves’ addresses are 010, 001, and 000, corresponding to their
positions in the cascade. The device address for a stand-alone device is always 000. Bits D11 through D8 comprise
the address of the register that is written with data carried in D7 through D0. D12 determines a read or write cycle
to the addressed register; a low selects a write cycle.
The following table shows the register map.
REGISTER MAP
D15
D14
D13
Device Address
D12
D11
RW
D10
D9
D8
Register Address
D7
D6
D5
X
D4
D3
D2
D1
D0
Control Register Content
Table A–1. Device Address
REGISTER MAP
D15 D14 D13 D12 D11 D10
D9
D8
Device Address R/W Register Adress
# Devices
in Cascade
1
2
3
4
5
6
7
8
Device 7
111
Device 6
110
110
D7
101
101
101
011
011
011
011
011
D5
X
D4
D3
D2
D1
D0
Register Content
DEVICE ADDRESS (D15–D13)
Device 5 Device 4 Device 3 Device 2
100
100
100
100
D6
Device 1
001
001
001
001
001
001
001
010
010
010
010
010
010
Device 0
000
000
000
000
000
000
000
000
Table A–2. Register Address
REGISTER NO.
D11
D10
D9
REGISTER NAME
0
0
0
0
No operation
1
0
0
1
Control 1
2
0
1
0
Control 2
3
0
1
1
Control 3
4
1
0
0
Control 4
A–1
A.1 Control Register 1
Table A–3. Register Map
D7
D6
D5
D4
D3
D2
D1
D0
DESCRIPTION
ovf
–
–
–
–
–
–
–
Decimator FIR overflow flag
–
1
–
–
–
–
–
–
Enable HYBRID receiver/MIC amp (A1)
–
0
–
–
–
–
–
–
Disable HYBRID/MIC amp (A1)
–
–
1
–
–
–
–
–
Bypass antialiasing filter
–
–
0
–
–
–
–
–
Enable antialiasing filter
–
–
–
1
–
–
–
–
Select AUXP and AUXM for ADC
–
–
–
0
–
–
–
–
Select INP and INM for ADC
–
–
–
–
1
–
–
–
Software reset
–
–
–
–
0
–
–
–
Default
–
–
–
–
–
1
–
–
Bypass decimation/interpolation FIR filter
–
–
–
–
–
0
–
Normal operation with FIR filter
–
–
–
–
–
–
1
–
Enable HYBRID transmitter/MIC amps (A3,A4)
–
–
–
–
–
–
0
–
Disable HYBRID transmitter/MIC amps (A3,A4)
–
–
–
–
–
–
–
1
16-bit data format for DAC
–
–
–
–
–
–
–
0
15-bit data + LSB format for DAC
Default value: 00000000
NOTE: A software reset is a one-shot operation and this bit is cleared to 0 after reset. It is not necessary to write a 0 to end the
master reset operation.
A.2 Control Register 2
Table A–4. Control Register 2
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
Low-power operation mode
0
–
–
–
–
–
–
–
Normal operation mode
–
1
–
–
–
–
–
–
S–D modulator stops
–
0
–
–
–
–
–
–
S–D modulator runs
–
–
R
–
–
–
–
–
Reserved
–
–
–
1
1
1
1
1
Frequency Divider N = 31
–
–
–
•
•
–
–
–
•
•
–
–
–
–
–
–
0
0
0
0
1
Frequency Divider N = 1
–
–
–
0
0
0
0
0
Frequency Divider N = 32
•
DIVIDE VALUE
•
Default value: 00000000
NOTE: The serial port interface always gluelessly works with the DSP. The following modes will not produce
50% duty cycle SCLK:
1. If the number of devices in cascade >4 and N is an odd number (i.e., N = 1, 3, 5,...)
2. If the number of devices in cascade ≤ 4, FIR is bypassed, and N ≠ 4, 8, 12, 16, 20, 24, 28, 32
A–2
A.3 Control Register 3
Table A–5. Control Register 3
D7
D6
D5
D4
D3
D2
D1
D0
DESCRIPTION
0
0
–
–
–
–
–
–
Default
0
1
–
–
–
–
–
–
Analog loopback enabled
1
0
–
–
–
–
–
–
Digital loopback enabled
1
1
–
–
–
–
–
–
Event-monitor mode enabled (write cycle only)
–
–
1
–
–
–
–
–
Continuous data-transfer mode (master only)
–
–
0
–
–
–
–
–
Default
–
–
–
1
–
–
–
–
FLAG output = D3
–
–
–
0
–
–
–
–
FLAG output = secondary communication flag
–
–
–
F
–
–
–
FLAG value
–
–
–
–
–
0
0
–
Default
–
–
–
–
–
0
1
–
Disable ADC channel
–
–
–
–
–
1
0
–
Disable DAC channel
–
–
–
–
–
1
1
–
Software power-down mode
–
–
–
–
–
–
–
1
16-bit data format for ADC
–
–
–
–
–
–
–
0
Not 16-bit data format for ADC
Default value: 00000000
A–3
A.4 Control Register 4
Table A–6. Control Register 4
D7
D6
D5
D4
D3
D2
D1
D0
1
1
1
1
–
–
–
–
ADC input PGA gain = MUTE
1
1
1
0
–
–
–
–
ADC input PGA gain = 24 dB
1
1
0
1
–
–
–
–
ADC input PGA gain = 18 dB
1
1
0
0
–
–
–
–
ADC input PGA gain = 12 dB
1
0
1
1
–
–
–
–
ADC input PGA gain = 9 dB
1
0
1
0
–
–
–
–
ADC input PGA gain = 6 dB
1
0
0
1
–
–
–
–
ADC input PGA gain = 3 dB
1
0
0
0
–
–
–
–
ADC input PGA gain = –3 dB
0
1
1
1
–
–
–
–
ADC input PGA gain = –6 dB
0
1
1
0
–
–
–
–
ADC input PGA gain = –9 dB
0
1
0
1
–
–
–
–
ADC input PGA gain = –12 dB
0
1
0
0
–
–
–
–
ADC input PGA gain = –18 dB
0
0
1
1
–
–
–
–
ADC input PGA gain = –24 dB
0
0
1
0
–
–
–
–
ADC input PGA gain = –30 dB
0
0
0
1
–
–
–
–
ADC input PGA gain = –36 dB
0
0
0
0
–
–
–
–
ADC input PGA gain = 0 dB
–
–
–
–
1
1
1
1
DAC output PGA gain = MUTE
–
–
–
–
1
1
1
0
DAC output PGA gain = 24 dB
–
–
–
–
1
1
0
1
DAC output PGA gain = 18 dB
–
–
–
–
1
1
0
0
DAC output PGA gain = 12 dB
–
–
–
–
1
0
1
1
DAC output PGA gain = 9 dB
–
–
–
–
1
0
1
0
DAC output PGA gain = 6 dB
–
–
–
–
1
0
0
1
DAC output PGA gain = 3 dB
–
–
–
–
1
0
0
0
DAC output PGA gain = –3 dB
–
–
–
–
0
1
1
1
DAC output PGA gain = –6 dB
–
–
–
–
0
1
1
0
DAC output PGA gain = –9 dB
–
–
–
–
0
1
0
1
DAC output PGA gain = –12 dB
–
–
–
–
0
1
0
0
DAC output PGA gain = –18 dB
–
–
–
–
0
0
1
1
DAC output PGA gain = –24 dB
–
–
–
–
0
0
1
0
DAC output PGA gain = –30 dB
–
–
–
–
0
0
0
1
DAC output PGA gain = –36 dB
–
–
–
–
0
0
0
0
DAC output PGA gain = 0 dB
Default value: 00000000
A–4
DESCRIPTION
TLV320AIC11
AURXFP
AURXM
AURXCP
AntiAliasing
Filter
PGA
SigmaDelta
ADC
Vref
VMID
DTXOP
DTXIM
DTXIP
DTXOM
OUTP
PGA
Low
Pass
Filter
SigmaDelta
DAC
OUTM
Figure A–1. Differential Configuration for Hybrid Connection
A–5
TLV320AIC11
AURXFP
AURXM
AURXCP
AntiAliasing
Filter
PGA
SigmaDelta
ADC
Vref
VMID
DTXOP
DTXIM
DTXIP
DTXOM
OUTP
PGA
OUTM
Figure A–2. Single-Ended Configuration of Hybrid Connection
A–6
Low
Pass
Filter
SigmaDelta
DAC
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  2000, Texas Instruments Incorporated