TI TRF371135IRGZR

TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
INTEGRATED IQ DEMODULATOR
Check for Samples: TRF371135
FEATURES
DESCRIPTION
•
•
The TRF371135 is a highly linear and integrated
direct-conversion quadrature demodulator. The
TRF371135 integrates balanced I and Q mixers, LO
buffers, and phase splitters to convert an RF signal
directly to I and Q baseband. The on-chip
programmable-gain amplifiers allow adjustment of the
output signal level without the need for external
variable-gain (attenuator) devices. The TRF371135
integrates programmable baseband low-pass filters
that attenuate nearby interference, eliminating the
need for an external baseband filter.
1
2
•
•
•
•
•
•
•
Frequency Range: 1700 MHz to 6000 MHz
Integrated Baseband Programmable-Gain
Amplifier
On-Chip Programmable Baseband Filter
High Out-of-Band IP3: 22 dBm at 3550 MHz
High Out-of-Band IP2: 52 dBm at 3550 MHz
Hardware and Software Power Down
Three-Wire Serial Interface
Single Supply: 4.5-V to 5.5-V Operation
Silicon Germanium Technology
Housed in a 7-mm × 7-mm QFN package, the
TRF371135 provides the smallest and most
integrated
receiver
solution
available
for
high-performance equipment.
APPLICATIONS
•
•
•
•
Multicarrier Wireless Infrastructure
WiMAX
High-Linearity Direct-Downconversion
Receiver
LTE (Long Term Evolution)
To Microcontroller
READBACK
NC
Gain_B1
Gain_B2
NC
Gain_B0
MIXIoutn
NC
STROBE
MIXIoutp
CLOCK
RFin
DATA
To Microcontroller
48 47 46 45 44 43 42 41 40 39 38 37
36
GNDDIG
1
VCCDIG
2
35
GND
CHIP_EN
3
34
BBIoutn
VCCMIX1
4
33
BBIoutp
VCCBBI
To ADC I
GND
5
32
GND
MIXinp
6
31
LOip
MIXinn
7
30
LOin
GND
8
29
VCCLO
VCCMIX2
9
28
BBQoutp
NC
10
27
BBQoutn
NC
11
26
LOin
TRF371135
NC
GND
VCCBBQ
VCM
VCCBIAS
GNDBIAS
NC
REXT
NC
MIXQoutn
GND
MIXQoutp
GND
25
12
13 14 15 16 17 18 19 20 21 22 23 24
GND
GND
To ADC Q
30 kW
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE DEVICE OPTIONS (1)
PRODUCT
PACKAGE
LEAD
PACKAGE
DESIGNATOR(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKINGS
TRF371135
QFN-48
RGZ
–40°C to 85°C
TRF371135
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
TRF371135IRGZR
Tape and reel, 2500
TRF371135IRGZT
Tape and reel, 500
MIXIoutn
44
45
MIXIoutp
FUNCTIONAL DIAGRAM
ADC Driver
VCCs
PGA
33
BBIoutp
34
BBIoutn
24
VCM
30
LOin
31
LOip
27
BBQoutn
28
BBQoutp
48
CLOCK
GND
DC Offset Control I
0°
MIXinp
6
MIXinn
7
90°
DC Offset Control Q
PGA
ADC Driver
CHIP_EN
3
Power
Down
DC Offset Control
47
LPFADJ Control
46
37
DATA
STROBE
READBACK
Gain_B2
39
40
Gain_B1
41
Gain_B0
17
MIXQoutn
MIXQoutp
16
PGA Control Q
SPI
B0385-01
(1)
2
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
DEVICE INFORMATION
PIN ASSIGNMENTS
space
NC
READBACK
Gain_B2
Gain_B0
Gain_B1
NC
NC
MIXIoutn
STROBE
MIXIoutp
DATA
CLOCK
RGZ PACKAGE
QFN-48
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
36
VCCBBI
GNDDIG
1
VCCDIG
2
35
GND
CHIP_EN
3
34
BBIoutn
VCCMIX1
4
33
BBIoutp
GND
5
32
GND
MIXinp
6
31
LOip
TRF371135
MIXinn
7
30
LOin
GND
8
29
VCCLO
VCCMIX2
9
28
BBQoutp
NC
10
27
BBQoutn
NC
11
26
GND
VCCBBQ
VCM
NC
GNDBIAS
VCCBIAS
REXT
NC
NC
MIXQoutn
GND
MIXQoutp
GND
25
12
13 14 15 16 17 18 19 20 21 22 23 24
GND
GND
PIN FUNCTIONS
PIN
NO.
NAME
I/O
DESCRIPTION
1
GNDDIG
Digital ground
2
VCCDIG
3
CHIP_EN
4
VCCMIX1
5
GND
6
MIXinp
I
Mixer input: positive terminal
7
MIXinn
I
Mixer input: negative terminal
8
GND
Ground
9
VCCMIX2
Mixer power supply
10
NC
No connect
11
NC
No connect
12
GND
Ground
13
GND
Ground
14
GND
Ground
15
GND
Ground
Digital power supply
I
Chip enable
Mixer power supply
Ground
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
3
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
PIN FUNCTIONS (continued)
PIN
NO.
4
NAME
I/O
DESCRIPTION
16
MIXQoutp
O
Mixer Q output: positive terminal
17
MIXQoutn
O
Mixer Q output: negative terminal
18
NC
19
NC
20
REXT
21
VCCBIAS
Bias block power supply
22
GNDBIAS
Bias block ground
23
NC
24
VCM
25
VCCBBQ
26
GND
27
BBQoutn
O
Baseband Q (in quadrature) output: negative terminal
28
BBQoutp
O
Baseband Q (in quadrature) output: positive terminal
29
VCCLO
30
LOin
I
Local oscillator input: negative terminal
31
LOip
I
Local oscillator input: positive terminal
32
GND
33
BBIoutp
O
Baseband I (in-phase) output: positive terminal
34
BBIoutn
O
Baseband I (in-phase) output: negative terminal
35
GND
Ground
36
VCCBBI
Baseband I (in phase) power supply
37
NC
No connect
38
READBACK
O
SPI readback data
39
Gain_B2
I
PGA fast gain control bit 2
40
Gain_B1
I
PGA fast gain control bit 1
41
Gain_B0
I
PGA fast gain control bit 0
42
NC
43
NC
44
MIXIoutn
O
Mixer I output: negative terminal
45
MIXIoutp
O
Mixer I output: positive terminal
46
STROBE
I
SPI enable
47
DATA
I
SPI data input
48
CLOCK
I
SPI clock input
No connect
No connect
O
Reference bias external resistor
No connect
I
Baseband common-mode input voltage
Baseband Q chain power supply
Ground
Local oscillator power supply
Ground
No connect
No connect
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
VALUE
UNIT
Supply voltage range (2)
–0.3 to 6
V
Digital I/O voltage range
–0.3 to 6
V
Operating free-air temperature range, TA
–40 to 85
°C
Operating virtual junction temperature range, TJ
–40 to 150
°C
Storage temperature range, Tstg
–65 to 150
°C
(1)
(2)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
VCC
Power-supply voltage
MIN
NOM
MAX
4.5
5
5.5
V
940
µVPP
Power-supply voltage ripple
UNIT
TA
Operating free-air temperature range
–40
85
°C
TJ
Operating virtual junction temperature range
–40
150
°C
MAX
UNIT
THERMAL CHARACTERISTICS
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER (1)
TEST CONDITIONS
Soldered slug, no airflow
RqJA
Thermal resistance, junction-to-ambient
(1)
(2)
TYP
26
Soldered slug, 200-LFM airflow
20.1
Soldered slug, 400-LFM airflow
17.4
RqJA (2)
RqJB
MIN
°C/W
25
Thermal resistance, junction-to-board
12
°C/W
Determined using JEDEC standard JESD-51 with high-K board
16 layers, high-K board
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
5
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
ELECTRICAL CHARACTERISTICS
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC PARAMETERS
ICC
Total supply current
370
mA
Power-down current
2
mA
IQ DEMODULATOR AND BASEBAND SECTION
fRF
Frequency range
1700
Gain range
22
(1)
6000
24
MHz
dB
Gain step
See
1
dB
Pinmax
Max. RF power input
Before damage
25
dBm
OIP3
Output third-order intercept point
Gain setting = 24 (2)
30
dBVRMS
3
dBVRMS
1 tone
(3)
P1dBmin
Min. output compression point
fmin
Min. baseband low-pass filter cutoff
frequency
1-dB point
fmax
Max. baseband low-pass filter cutoff
frequency
3-dB point (4)
fbypass
Baseband low-pass filter cutoff frequency in
bypass mode
3-dB point (5)
(4)
700
15
8
2 × fC
32
3 × fC
54
4 × fC
75
5 × fC
Image suppression
Vcm
Output, common-mode
Baseband harmonic level
dB
90
fLO = 3550 MHz
–35
Output BB attenuator
Output load impedance
MHz
1
1.5 × fC
Baseband relative attenuation at LPF cutoff
frequency (fC) (6)
MHz
30
1 × fC
Fsel
kHz
dB
3
dB
1
kΩ
Parallel capacitance
20
pF
Measured at I- and Q-channel
baseband outputs
1.5
V
–95
dBc
–103
dBc
Parallel resistance
Second harmonic
(7)
Third harmonic (7)
LOCAL OSCILLATOR PARAMETERS
Local oscillator frequency
1700
LO input level
See (8)
LO leakage
At MIXinn/p at 0-dBm LO drive level
–3
0
6000
MHz
6
dBm
–58
dBm
DIGITAL INTERFACE
VIH
High-level input voltage
0.6 × VCC
VIL
Low-level input voltage
0
VOH
High-level output voltage
VOL
Low-level output voltage
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
6
5
VCC
V
0.8
V
0.8 × VCC
V
0.2 × VCC
V
Two consecutive gain settings
Two CW tones at an offset from LO frequency smaller than the baseband-filter cutoff frequency. Performance is set by baseband
circuitry regardless of LO frequency.
Single CW tone at an offset from LO frequency smaller than the baseband-filter cutoff frequency. Performance is set by baseband
circuitry regardless of LO frequency.
Baseband low-pass filter cutoff frequency is programmable through SPI register LPFADJ. LPFADJ = 0 corresponds to maximum
bandwidth; LPFADJ = 255 corresponds to minimum BW.
Filter Ctrl setting equal to 0
Attenuation relative to passband gain
LO frequency set to 3.55 GHz. I or Q output power level –6 dBVRMS differential. Gain setting at 24. DC offset calibration engaged. Input
signal set at 1-MHz offset.
LO power outside of this range is possible but may introduce degraded performance.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
ELECTRICAL CHARACTERISTICS
VCC = 5 V, LO power = 0 dBm, TA = 25°C (1) (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
fLO = 1740 MHz
Gmax
Maximum gain (2)
Gain setting = 24
45
dB
NF
Noise figure
Gain setting = 24
10
dB
(3) (4)
19
dBm
60
dBm
IIP3
Third-order input intercept point
Gain setting = 24
IIP2
Second-order input intercept point
Gain setting = 24 (4) (5)
Gmax
Maximum gain (2)
Gain setting = 24
44.3
NF
Noise figure
Gain setting = 24
10.5
IIP3
Third-order input intercept point
Gain setting = 24 (3) (4)
20
dBm
IIP2
Second-order input intercept point
Gain setting = 24 (4) (5)
57
dBm
Gmax
Maximum gain (2)
Gain setting = 24
44
dB
NF
Noise figure
Gain setting = 24
11
dB
(3) (4)
fLO = 1950 MHz
dB
dB
fLO = 2025 MHz
IIP3
Third-order input intercept point
Gain setting = 24
21
dBm
IIP2
Second-order input intercept point
Gain Setting = 24 (4) (5)
57
dBm
Gmax
Maximum gain (2)
Gain setting = 24
43
dB
N3F
Noise figure
Gain setting = 24
12
IIP3
Third-order input intercept point
Gain setting = 24 (3) (4)
23.5
dBm
IIP2
Second-order input intercept point
Gain setting = 24 (4) (5)
58
dBm
Maximum gain (2)
Gain setting = 24
40
dB
Gain setting = 24
13.8
dB
fLO = 2400 MHz
dB
fLO = 3550 MHz
Gmax
NF
Noise figure
Gain setting = 16
15
dB
IIP3
Third-order input intercept point
Gain setting = 24 (3) (4)
22
dBm
IIP2
Second-order input intercept point
Gain setting = 24 (4) (5)
52
dBm
Gmax
Maximum gain (2)
Gain setting = 24
37.5
dB
NF
Noise figure
Gain setting = 24
17.5
dB
fLO = 5400 MHz
(3) (4)
22
dBm
60
dBm
IIP3
Third-order input intercept point
Gain setting = 24
IIP2
Second-order input intercept point
Gain setting = 24 (4) (5)
(1)
(2)
(3)
(4)
(5)
For broadband frequency sweeps, the Picosecond balun (model #5310A) is used at the RF and LO inputs. For the frequency band
between 3300 MHz and 3800 MHz, the Johanson 3600BL14M050E balun is used. For the frequency band between 4900 MHz and
5900 MHz the Johanson 5400BL15B050E balun is used. Performance parameters adjusted for balun insertion loss. Recommended
baluns for respective frequency bands are shown as follows:
1740 MHz: Murata LDB211G8005C-001 (or equivalent)
1950 MHz: Murata LDB211G9005C-001 (or equivalent)
2025 MHz: Murata LDB211G9005C-001 (or equivalent)
2500 MHz: Murata LDB212G4005C-001 (or equivalent)
3550 MHz: Johanson 3600BL14M050E (or equivalent)
5400 MHz: Johanson 5400BL15B050E (or equivalent)
Gain defined as voltage gain from Mixin (VRMS) to either baseband output: BBI/Qout (VRMS)
Two CW tones of –30 dBm at fRF1 = fLO ±(2 × fC) and fRF2 = fLO ±[(4 × fC) + 100 kHz] (fC = baseband filter 1-dB cutoff frequency).
Because the 2-tone interferers are outside of the baseband filter bandwidth, the results are inherently independent of the gain setting.
Intermodulation parameters are recorded at maximum gain setting, where measurement accuracy is best.
Two CW tones of –30 dBm at fRF1 = fLO ±(2 × fC) and fRF2 = fLO ±[(2 × fC) + 100 kHz]; IM2 product measured at 100-kHz output
frequency (fC = baseband filter 1-dB cutoff frequency)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
7
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TIMING REQUIREMENTS
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
t(CLK)
Clock period
50
ns
t(CH)
Clock-signal high time
20
ns
t(CL)
Clock-signal low time
20
ns
tsu1
Setup time, data
10
ns
th
Hold time, data
10
ns
tw
Pulse duration, STROBE
20
ns
tsu2
Setup time, STROBE
10
ns
td
Delay time, clock to readback-data output
10
ns
tsu1
t(CL)
t(CLK)
th
t(CH)
st
Register Write
CLOCK
DATA
nd
1
Write
CLOCK
Pulse
32
Write
CLOCK
Pulse
DB0 (LSB)
Address Bit 0
DB1
Address Bit 1
DB3
Address Bit 3
DB2
Address Bit 2
DB30
DB29
READBACK DATA READBACK DATA
Bit 30
Bit 29
DB31 (MSB)
READBACK DATA
Bit 31
tsu2
"End of Write
Cycle"Pulse
Latch
Enable
nd
CLOCK
32
Write
CLOCK
Pulse
tsu2
READBACK
tw
st
1
Read
CLOCK
Pulse
nd
nd
2
Read
CLOCK
Pulse
rd
32
Read
CLOCK
Pulse
33
Read
CLOCK
Pulse
tw
td
STROBE
"End of Write
Cycle" Pulse
READBACK
DATA
READBACK
Data Bit 0
READ
BACK
Data
Bit 1
READ
BACK
Data
Bit 29
READBACK
Data Bit 30
READBACK
Data Bit 31
T0265-02
Figure 1. Timing Requirements Diagram
8
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
Table of Graphs
Broadband Data (1700-6000 MHz)
Gain
vs LO frequency (1)
Figure 2, Figure 3, Figure 4
Noise figure
vs LO frequency (1)
Figure 5, Figure 6, Figure 7
(2) (3) (4)
IIP3
vs LO frequency
IIP2
vs LO frequency (2) (3) (4)
Figure 8, Figure 9, Figure 10
Figure 11, Figure 12, Figure 13
3.5G Band Data (3300-3800 MHz)
Gain
vs LO frequency (5)
IIP3
vs LO frequency (3) (4) (5)
Figure 17, Figure 18, Figure 19, Figure 20
IIP2
vs LO frequency (3) (4) (5)
Figure 21, Figure 22, Figure 23, Figure 24
Noise figure
vs LO frequency (5)
Figure 25, Figure 26, Figure 27
Gain
vs LO frequency (6)
Figure 28, Figure 29, Figure 30
IIP3
vs LO frequency (3) (4) (6)
Figure 31, Figure 32, Figure 33
IIP2
vs LO frequency
(3) (4) (6)
Figure 34, Figure 35, Figure 36
Noise figure
vs LO frequency (6)
Figure 14, Figure 15, Figure 16
5G Band Data (4900-5900 MHz)
Figure 37, Figure 38, Figure 39
Baseband-Related Data
OIP3
vs Frequency offset (7)
Noise figure
vs BB gain setting
Gain
vs BB gain setting
Gain
vs Frequency offset
Figure 46, Figure 47
Gain
vs Frequency offset (bypass mode)
Figure 48, Figure 49
1-dB LPF corner frequency
vs LPFADJ setting
Figure 50
Relative LPF group delay
Frequency offset (8)
Figure 51
Image rejection
vs BB frequency offset
Figure 52
DC offset limit
vs Temperature (9)
Figure 53
Out-of-band P1dB
vs Relative offset multiplier to corner frequency (10)
Figure 54
Figure 40, Figure 41, Figure 42, Figure 43
Figure 44
Figure 45
(1)
Measured with broadband Picosecond 5310A balun on the LO input and single-ended connection on the RF input. Performance gain
adjusted for the 3-dB differential to single-ended insertion loss.
(2) Measured with broadband Picosecond 5310A balun on the LO input and RF input. Balun insertion loss is compensated for in the
measurement.
(3) Out-of-band intercept point is defined with tones that are at least 2 times farther out than the programmed LPF corner frequency that
generates an intermodulation tone that falls inside the LPF passband.
(4) Out-of-band intercept point is dependent on the demodulator performance and not the baseband circuitry; the measurement is taken at
maximum gain but is valid across all PGA settings.
(5) Measured with Johanson 3600BL14M050E balun on the LO input and RF input. All dc-blocking and bypass capacitors are 4.7 pF as
listed on the EVM schematic.
(6) Measured with Johanson 5400 BL15B050E balun on the LO input and RF input. All dc-blocking and bypass capacitors are 1.8 pF as
listed on the EVM schematic.
(7) Measured with filter in bypass mode to characterize the pass-band circuitry across baseband frequencies. Tone spacing set to 100 kHz,
and tone frequencies are varied from 5/5.1 MHz to 25/25.1 MHz (x-axis of graph).
(8) Relative to the low-frequency offset group delay in bypass mode
(9) Idet set to 50 µA; RF signal is off; LO at 2.4 GHz at 0 dBm; Det filter set to 1 kHz; Div set to 1024.
(10) In-band tone set to 1 MHz; out-of-band jammer tone set to specified relative offset ratio from the programmed corner frequency. Jammer
tone is increased until in-band tone compresses 1 dB.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
9
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
GAIN vs LO FREQUENCY
GAIN vs LO FREQUENCY
48
48
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
46
44
Gain (dB)
Gain (dB)
44
42
40
VCC = 4.5V
VCC = 5V
VCC = 5.5V
46
38
42
40
38
36
36
See Note 1
See Note 1
34
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G002
34
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G001
Figure 2.
Figure 3.
GAIN vs LO FREQUENCY
NOISE FIGURE vs LO FREQUENCY
20
48
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 6dBm
46
Noise Figure (dB)
Gain (dB)
44
18
42
40
38
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
16
14
12
10
36
See Note 1
34
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G003
See Note 1
8
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G004
Figure 4.
Figure 5.
NOISE FIGURE vs LO FREQUENCY
NOISE FIGURE vs LO FREQUENCY
20
VCC = 4.5V
VCC = 5 V
VCC = 5.5V
18
Noise Figure (dB)
Noise Figure (dB)
18
20
16
14
12
10
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 6dBm
16
14
12
10
See Note 1
8
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G005
See Note 1
8
1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
LO Frequency (MHz)
G006
Figure 6.
10
Figure 7.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
34
32
30
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
IIP3 (dBm)
28
26
24
22
20
18
16
14
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
34
32
30
IIP3 (dBm)
28
26
24
22
20
18
16
See Notes 2, 3 and 4
14
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G007
Figure 8.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
11
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
32
30
VCC = 4.5V
VCC = 5V
VCC = 5.5V
28
IIP3 (dBm)
26
24
22
20
18
16
14
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
32
30
28
IIP3 (dBm)
26
24
22
20
18
16
See Notes 2, 3 and 4
14
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G008
Figure 9.
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
34
32
30
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
28
IIP3 (dBm)
26
24
22
20
18
16
14
12
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
34
32
30
28
IIP3 (dBm)
26
24
22
20
18
16
14
See Notes 2, 3 and 4
12
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G009
Figure 10.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
13
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
IIP2 (dBm)
80
70
60
50
40
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 2, 3 and 4
40
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G010
Figure 11.
14
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
VCC = 4.5V
VCC = 5V
VCC = 5.5V
IIP2 (dBm)
80
70
60
50
40
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 2, 3 and 4
40
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G011
Figure 12.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
15
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, BROADBAND DATA (1700 MHz–6000 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
90
IIP2 (dBm)
80
70
60
50
40
30
1500
500
2000
2000
2500
2500
3000
3000
3500
3500
4000
4000
4500
4500
5000
5000
5500
5500
6000
6000
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 2, 3 and 4
40
1500
2000
2500
3000
3500
4000
LO Frequency (MHz)
4500
5000
5500
6000
G012
Figure 13.
16
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
GAIN vs LO FREQUENCY
GAIN vs LO FREQUENCY
44
44
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
43
42
41
Gain (dB)
Gain (dB)
42
VCC = 4.5V
VCC = 5V
VCC = 5.5V
43
40
39
38
41
40
39
38
37
37
See Note 5
36
3300
3400
3500
3600
LO Frequency (MHz)
3700
3800
See Note 5
36
3300
3400
3500
3600
LO Frequency (MHz)
G013
Figure 14.
3700
3800
G014
Figure 15.
GAIN vs LO FREQUENCY
44
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 6dBm
43
Gain (dB)
42
41
40
39
38
37
See Note 5
36
3300
3400
3500
3600
LO Frequency (MHz)
3700
3800
G015
Figure 16.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
17
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
IIP3 (dBm)
26
24
22
20
18
16
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
30
28
IIP3 (dBm)
26
24
22
20
18
See Notes 3, 4 and 5
16
3300
3400
G016
Figure 17.
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
VCC = 4.5V
VCC = 5V
VCC = 5.5V
IIP3 (dBm)
26
24
22
20
18
16
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
30
28
IIP3 (dBm)
26
24
22
20
18
See Notes 3, 4 and 5
16
3300
3400
G017
Figure 18.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
19
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
IIP3 (dBm)
26
24
22
20
18
16
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
30
28
IIP3 (dBm)
26
24
22
20
18
See Notes 3, 4 and 5
16
3300
3400
G018
Figure 19.
20
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
IIP3 (dBm)
26
24
22
20
18
16
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
30
28
IIP3 (dBm)
26
24
22
20
18
See Notes 3, 4 and 5
16
3300
3400
G019
Figure 20.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
21
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
IIP2 (dBm)
80
70
60
50
40
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 3, 4 and 5
40
3300
3400
G020
Figure 21.
22
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
VCC = 4.5V
VCC = 5V
VCC = 5.5V
IIP2 (dBm)
80
70
60
50
40
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 3, 4 and 5
40
3300
3400
G021
Figure 22.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
23
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
IIP2 (dBm)
80
70
60
50
40
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 3, 4 and 5
40
3300
3400
G022
Figure 23.
24
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
100
90
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
IIP2 (dBm)
80
70
60
50
40
3300
330
3400
3400
3500
3500
3600
3600
3700
3700
3800
3800
3500
3600
LO Frequency (MHz)
3700
3800
Q
100
90
IIP2 (dBm)
80
70
60
50
See Notes 3, 4 and 5
40
3300
3400
G023
Figure 24.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
25
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 3.5G BAND DATA (3300 MHz–3800 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 3600BL14M050E (unless otherwise noted)
NOISE FIGURE vs LO FREQUENCY
NOISE FIGURE vs LO FREQUENCY
20
19
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
19
18
17
Noise Figure (dB)
Noise Figure (dB)
18
20
16
15
14
13
12
17
16
15
14
13
12
11
10
3300
VCC = 4.5V
VCC = 5 V
VCC = 5.5V
11
See Note 5
3400
3500
3600
LO Frequency (MHz)
3700
3800
See Note 5
10
3300
3400
3500
3600
LO Frequency (MHz)
G026
Figure 25.
3700
3800
G027
Figure 26.
NOISE FIGURE vs LO FREQUENCY
20
19
Noise Figure (dB)
18
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 6dBm
17
16
15
14
13
12
11
10
3300
See Note 5
3400
3500
3600
LO Frequency (MHz)
3700
3800
G028
Figure 27.
26
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
GAIN vs LO FREQUENCY
GAIN vs LO FREQUENCY
42
42
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
41
40
39
Gain (dB)
Gain (dB)
40
VCC = 4.5V
VCC = 5V
VCC = 5.5V
41
38
37
36
39
38
37
36
35
35
See Note 6
34
4900
5100
5300
5500
LO Frequency (MHz)
5700
5900
See Note 6
34
4900
5100
5300
5500
LO Frequency (MHz)
G044
Figure 28.
5700
5900
G045
Figure 29.
GAIN vs LO FREQUENCY
42
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 3dBm
41
Gain (dB)
40
39
38
37
36
35
See Note 6
34
4900
5100
5300
5500
LO Frequency (MHz)
5700
5900
G046
Figure 30.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
27
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
IIP3 (dBm)
26
24
22
20
18
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
18
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
30
28
IIP3 (dBm)
26
24
22
20
G047
Figure 31.
28
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
VCC = 4.5V
VCC = 5V
VCC = 5.5V
IIP3 (dBm)
26
24
22
20
18
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
18
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
30
28
IIP3 (dBm)
26
24
22
20
G048
Figure 32.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
29
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP3 vs LO FREQUENCY
W
I
30
28
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
IIP3 (dBm)
26
24
22
20
18
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
18
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
30
28
IIP3 (dBm)
26
24
22
20
G049
Figure 33.
30
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
90
IIP2 (dBm)
80
TA = −40°C
TA = −10°C
TA = 25°C
TA = 85°C
70
60
50
40
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
40
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
90
IIP2 (dBm)
80
70
60
50
G050
Figure 34.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
31
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
90
VCC = 4.5V
VCC = 5V
VCC = 5.5V
IIP2 (dBm)
80
70
60
50
40
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
40
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
90
IIP2 (dBm)
80
70
60
50
G051
Figure 35.
32
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
IIP2 vs LO FREQUENCY
W
I
90
IIP2 (dBm)
80
LO Pwr = −3dB
LO Pwr = 0dB
LO Pwr = 3dB
LO Pwr = 6dB
70
60
50
40
4900
490
5000
5000
5100
5100
5200
5200
5300
5300
5400
5400
Q
5500
5500
5600
5600
5700
5700
5800
5800
5900
5900
See Notes 3, 4 and 6
40
4900
5000
5100
5200
5300
5400
5500
LO Frequency (MHz)
5600
5700
5800
5900
90
IIP2 (dBm)
80
70
60
50
G052
Figure 36.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
33
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, 5G BAND DATA (4900 MHz–5900 MHz) (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, balun = Johanson 5400BL15B050E (unless otherwise noted)
NOISE FIGURE vs LO FREQUENCY
NOISE FIGURE vs LO FREQUENCY
20
T A = −40°C
T A = −10°C
T A = 25°C
T A = 85°C
19
Noise Figure (dB)
Noise Figure (dB)
19
20
18
17
16
15
VCC = 4.5V
VCC = 5 V
VCC = 5.5V
18
17
16
15
See Note 6
14
4900
5100
5300
5500
LO Frequency (MHz)
5700
See Note 6
5900
14
4900
5100
5300
5500
LO Frequency (MHz)
G053
Figure 37.
5700
5900
G054
Figure 38.
NOISE FIGURE vs LO FREQUENCY
20
Noise Figure (dB)
19
LO Pwr = −3dBm
LO Pwr = 0dBm
LO Pwr = 3dBm
LO Pwr = 6dBm
18
17
16
15
See Note 6
14
4900
5100
5300
5500
LO Frequency (MHz)
5700
5900
G055
Figure 39.
34
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, BASEBAND-RELATED DATA
VCC = 5 V, LO power = 0 dBm, TA = 25°C, independent of balun used (unless otherwise noted)
OIP3 vs FREQUENCY OFFSET
OIP3 vs FREQUENCY OFFSET
52
52
T A = −40°C
T A = 25°C
T A = 85°C
50
48
46
OIP3 (dBVrms)
OIP3 (dBVrms)
48
44
42
40
46
44
42
40
38
38
36
36
34
VCC = 4.5V
VCC = 5V
VCC = 5.5V
50
34
See Note 7
32
See Note 7
32
0
5
10
15
Frequency Offset (MHz)
20
25
0
5
10
15
Frequency Offset (MHz)
G029
Figure 40.
OIP3 vs FREQUENCY OFFSET
G030
OIP3 vs FREQUENCY OFFSET
50
BB Gain = 12dB
BB Gain = 16dB
BB Gain = 20dB
BB Gain = 24dB
48
46
3dB Attn On
3dB Attn Off
48
46
44
OIP3 (dBVrms)
OIP3 (dBVrms)
25
Figure 41.
50
42
40
38
36
44
42
40
38
36
34
34
See Note 7
See Note 7
32
32
0
5
10
15
Frequency Offset (MHz)
20
25
0
5
10
15
Frequency Offset (MHz)
G031
Figure 42.
20
25
G032
Figure 43.
NOISE FIGURE vs BB GAIN SETTING
GAIN vs BB GAIN SETTING
28
43
3dB Attn On
3dB Attn Off
3dB Attn On
3dB Attn Off
40
25
37
34
22
Gain (dB)
Noise Figure (dB)
20
19
31
28
25
22
16
19
16
13
13
0
2
4
6
8
10 12 14 16
BB Gain Setting
18
20
22
24
0
2
G033
Figure 44.
4
6
8
10 12 14 16
BB Gain Setting
18
20
22
24
G034
Figure 45.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
35
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS, BASEBAND-RELATED DATA (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, independent of balun used (unless otherwise noted)
GAIN vs FREQUENCY OFFSET
GAIN vs FREQUENCY OFFSET
20
5
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
4
0
3
2
Gain (dB)
Gain (dB)
-20
-40
-60
-80
1
0
-1
-2
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
-100
0.1
-3
-4
1
10
Frequency Offset (MHz)
-5
0.1
100
1
10
Frequency Offset (MHz)
G035
Figure 46.
GAIN vs FREQUENCY OFFSET
GAIN vs FREQUENCY OFFSET
5
Filter Ctrl 0
Filter Ctrl 1
Filter Ctrl 2
Filter Ctrl 3
4
0
3
2
Gain (dB)
Gain (dB)
-20
-40
-60
1
0
-1
-2
Filter Ctrl 0
Filter Ctrl 1
Filter Ctrl 2
Filter Ctrl 3
-100
0.1
1
-3
-4
10
100
Frequency Offset (MHz)
-5
0.1
1000
1
10
Frequency Offset (MHz)
G037
Figure 48. Bypass Mode
1-dB LPF CORNER FREQUENCY vs LPFADJ SETTING
G038
RELATIVE LPF GROUP DELAY vs FREQUENCY OFFSET
500
See Note 8
14
Relative LPF Group Delay (ns)
1-dB LPF Corner Frequency (MHz)
100
Figure 49. Bypass Mode
16
12
10
8
6
4
2
0
0
50
100
150
LPFADJ Setting
200
250
Bypass
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
400
300
200
100
0
-100
0.1
G039
Figure 50.
36
G036
Figure 47.
20
-80
100
1
10
Frequency Offset (MHz)
100
G040
Figure 51.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
TYPICAL CHARACTERISTICS, BASEBAND-RELATED DATA (continued)
VCC = 5 V, LO power = 0 dBm, TA = 25°C, independent of balun used (unless otherwise noted)
IMAGE REJECTION vs BB FREQUENCY OFFSET
DC OFFSET LIMIT vs TEMPERATURE
0
60
See Note 9
40
DC Offset Limit (mV)
Image Rejection (dB)
-10
-20
-30
-40
-50
-60
-25
20
0
-20
-40
-20
-15
-10
-5
0
5
10
BB Frequency Offset (MHz)
15
20
-60
-45 -35 -25 -15 -5
25
G041
5 15 25 35 45 55 65 75 85
Temperature (°C)
G042
Figure 52.
Figure 53.
OUT-OF-BAND P1dB vs
REL OFFSET MULTIPLIER to CORNER FREQUENCY
15
LPFADJ = 0
LPFADJ = 25
LPFADJ = 85
LPFADJ = 142
Out-of-Band P1dB (dBm)
10
5
0
-5
-10
-15
-20
See Note 10
-25
0
0.5
1
1.5
2
2.5
3
3.5
4
Relative Offset Multiplier to Corner Frequency
4.5
G043
Figure 54.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
37
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
SERIAL INTERFACE PROGRAMMING REGISTERS DEFINITION
The TRF371135 features a three-wire serial programming interface (SPI) that controls an internal 32-bit shift
register. There are three signals that must be applied: CLOCK (pin 48), serial DATA (pin 47), and STROBE (pin
46). DATA (DB0–DB31) is loaded LSB-first and is read on the rising edge of CLOCK. STROBE is asynchronous
to CLOCK, and at its rising edge the data in the shift register is loaded into the selected internal register. The first
two bits (DB0–DB1) are the address to select the available internal registers.
READBACK Mode
The TRF371135 implements the capability to read back the content of the serial programming interface registers.
In addition, it is possible to read back the status of the internal DAC registers that are automatically set after an
auto dc-offset calibration. Each readback is consists of two phases: writing followed by the actual reading of the
internal data (refer to timing diagram in Figure 55).
During the writing phase, a command is sent to the TRF371135 to set it in readback mode and to specify which
register is to be read. In the proper reading phase, at each rising clock edge, the internal data is transferred into
the READBACK pin and can be read at the following falling edge (LSB first). The first clock after LE goes high
(end of writing cycle) is idle, and the following 32 clock pulses transfer the internal register content to the
READBACK pin.
tsu1
t(CL)
t(CLK)
th
t(CH)
st
Register Write
CLOCK
DATA
nd
1
Write
CLOCK
Pulse
32
Write
CLOCK
Pulse
DB0 (LSB)
Address Bit 0
DB1
Address Bit 1
DB3
Address Bit 3
DB2
Address Bit 2
DB30
DB29
READBACK DATA READBACK DATA
Bit 30
Bit 29
DB31 (MSB)
READBACK DATA
Bit 31
tsu2
"End of Write
Cycle"Pulse
Latch
Enable
nd
CLOCK
32
Write
CLOCK
Pulse
tsu2
READBACK
tw
st
1
Read
CLOCK
Pulse
nd
nd
2
Read
CLOCK
Pulse
rd
32
Read
CLOCK
Pulse
33
Read
CLOCK
Pulse
tw
td
STROBE
"End of Write
Cycle" Pulse
READBACK
Data Bit 0
READBACK
DATA
READ
BACK
Data
Bit 1
READ
BACK
Data
Bit 29
READBACK
Data Bit 30
READBACK
Data Bit 31
T0265-02
Figure 55. Serial Programming Timing Diagram
38
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
Table 1. Register Summary (1)
Bit #
Reg 1
Reg 2
ADDR<0,2>
ADDR<0,2>
Bit #
Bit0
Bit1
Bit2
Bit3
ADDR<3,4>
ADDR<3,4>
Bit5
PWD_MIX
EN_AUTOCAL
Bit6
NU
Bit6
Bit7
PWD_BUF
Bit7
Bit8
PWD_FILT
Bit8
Bit9
NU
Bit9
Bit10
PWD_DC_OFF_DIG
Bit11
NU
Bit4
Bit4
ADDR<0,2>
ADDR<0,2>
IDAC_BIT<0,7>
Bit13
Bit14
BBGAIN_<0,4>
Bit14
Bit15
Bit15
Bit16
Bit16
Bit17
QDAC_BIT<0,7>
Bit18
Bit19
Bit21
Bit22
IDET_B<0,1>
Bit23
Bit24
CAL_SEL
MIX_GM_TRIM<0,1>
ILOAD_a<0,5>
EN_FLT_B<0,1>
Bit27
EN_FASTGAIN
Bit28
GAIN_SEL
Bit29
OSC_TEST
Bit30
NU
Bit31
EN 3dB Attn
MIX_LO_TRIM<0,1>
LO_TRIM<0,1>
MIX_BUFF_TRIM<0,1>
ILOAD_b<0,5>
FLTR_TRIM<0,1>
OUT_BUFF_TRIM<0,1>
Cal_clk_sel
Bit8
Bit9
Bit10
Bit11
Bit13
Bit14
Bit15
Bit16
Bit21
Bit22
Bit22
Bit23
Bit23
Bit26
Bit25
QLOAD_b<0,5>
Bit26
Bit27
Bit28
Bit28
Bit31
DC_OFFSET_Q<0,7>
Bit24
Bit27
Bit30
NU
Bit12
Bit21
Bit29
Osc_trim<0,2>
Bit7
Bit20
NU
ID<0,1>
Bit6
Bit19
Bit24
Clk_div_ratio<0,2>
Bit5
Bit18
QLOAD_a<0,5>
ADDR<3,4>
Bit4
Bit17
Bit25
ADDR<0,2>
Bit3
Bit18
Bit20
LPFADJ_<0,7>
ADDR<3,4>
Bit17
Bit19
Bit20
ADDR<3,4>
Bit11
Bit13
Bit1
Bit2
Bit10
Bit12
Reg 0
Bit0
Bit5
Bit12
(1)
Bit #
Bit2
Bit3
Bit26
Reg 5
Bit0
Bit1
Bit25
Reg 3
Bypass
DC_OFFSET_I<0,7>
Bit29
Bit30
Fltr Ctrl_b<0,1>
Bit31
Register 4 is not used.
Table 2. Register 1 Device Setup
REGISTER 1
NAME
RESET VALUE
WORKING DESCRIPTION
Bit0
ADDR<0>
1
Bit1
ADDR<1>
0
Bit2
ADDR<2>
0
Bit3
ADDR<3>
1
Bit4
ADDR<4>
0
Bit5
PWD_MIX
0
Mixer power down (Off = 1)
Bit6
NU
0
Not used
Bit7
PWD_BUF
1
Mixer out test buffer power down (Off = 1)
Bit8
PWD_FILT
0
Baseband filter power down (Off = 1)
Bit9
NU
0
Not used
Bit10
PWD_DC_OFF_DIG
1
DC offset calibration power down (Off = 1)
Register address
SPI bank address
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
39
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
Table 2. Register 1 Device Setup (continued)
REGISTER 1
NAME
RESET VALUE
WORKING DESCRIPTION
Bit11
NU
1
Bit12
BBGAIN_0
1
Bit13
BBGAIN_1
1
Bit14
BBGAIN_2
1
Bit15
BBGAIN_3
1
Bit16
BBGAIN_4
0
Bit17
LPFADJ_0
0
Bit18
LPFADJ_1
0
Bit19
LPFADJ_2
0
Bit20
LPFADJ_3
0
Bit21
LPFADJ_4
0
Bit22
LPFADJ_5
0
Bit23
LPFADJ_6
0
Bit24
LPFADJ_7
1
Bit25
EN_FLT_B0
0
Bit26
EN_FLT_B1
0
Selects dc offset detector filter bandwidth.
Setting {00, 01, 11} = {10 MHz, 10 kHz, 1 kHz}
Bit27
EN_FASTGAIN
0
Enable external fast-gain control
Bit28
GAIN_SEL
0
Fast-gain control multiplier bit (×2 = 1)
Bit29
OSC_TEST
0
Enables OSC out on readback pin if = 1
Bit30
NU
0
Not used
Bit31
EN 3dB Attn
0
Enables output 3-dB attenuator
Not used
Baseband gain setting. Default = 15. Range is from 0 (minimum gain
setting) to 24 (maximum gain setting). See the Application Information
section for more information on gain setting and fast gain control
options.
Sets programmable low-pass filter corner frequency. Range = 255
(lowest corner frequency) to 0 (highest corner frequency). Default value
is 128.
EN_FLT_B0/1: These bits control the bandwidth of the detector used to measure the dc offset during the
automatic calibration. There is an RC filter in front of the detector that can be fully bypassed. EN_FLT_B0
controls the resistor (bypass = 1), while EN_FLT_B1 controls the capacitor (bypass = 1). The typical 3-dB cutoff
frequencies of the detector bandwidth are summarized in the following table (see the Application Information
section for more detail on the dc offset calibration and the detector bandwidth).
EN_FLT_B1
EN_FLT_B0
TYPICAL 3-dB CUTOFF FREQ
X
0
10 MHz
NOTES
Maximum bandwidth, bypass R, C
0
1
10 kHz
Enable R
1
1
1 kHz
Minimum bandwidth, enable R, C
Table 3. Register 2 Device Setup
40
REGISTER 2
NAME
RESET VALUE
Bit0
ADDR<0>
0
Bit1
ADDR<1>
1
Bit2
ADDR<2>
0
Bit3
ADDR<3>
1
Bit4
ADDR<4>
0
Bit5
EN_AUTOCAL
0
WORKING DESCRIPTION
Register address
SPI bank address
Enable autocal when = 1; reset to 0 when done.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
Table 3. Register 2 Device Setup (continued)
REGISTER 2
NAME
RESET VALUE
Bit6
IDAC_BIT0
0
Bit7
IDAC_BIT1
0
Bit8
IDAC_BIT2
0
WORKING DESCRIPTION
Bit9
IDAC_BIT3
0
Bit10
IDAC_BIT4
0
Bit11
IDAC_BIT5
0
Bit12
IDAC_BIT6
0
Bit13
IDAC_BIT7
1
Bit14
QDAC_BIT0
0
Bit15
QDAC_BIT1
0
Bit16
QDAC_BIT2
0
Bit17
QDAC_BIT3
0
Bit18
QDAC_BIT4
0
Bit19
QDAC_BIT5
0
Bit20
QDAC_BIT6
0
Bit21
QDAC_BIT7
1
Bit22
IDET_B0
1
Bit23
IDET_B1
1
Set reference current for digital calibration; Settings {00 to 11}
= {50 µA to 200 µA}. Setting 00 = highest resolution.
Bit24
CAL_SEL
1
DC offset calibration select. 0 = manual cal; 1 = autocal.
Bit25
Clk_div_ratio<0>
0
Bit26
Clk_div_ratio<1>
0
Bit27
Clk_div_ratio<2>
0
Bit28
Cal_clk_sel
1
Bit29
Osc_trim<0>
1
Bit30
Osc_trim<1>
1
Bit31
Osc_trim<2>
0
I-DAC bits to be set during manual dc offset cal
Q-DAC bits to be set during manual dc offset cal
Clk divider ratio. Setting {000 to 111} = {1, 8, 16, 128, 256, 1024, 2048,
16,684}. A higher div ratio (slower clk) improves cal accuracy and
reduces speed.
Select internal oscillator when 1, SPI clk when 0
Internal oscillator frequency trimming; setting {000} = ~300 kHz;
Setting {111} = ~1.8 MHz. Nominal setting {110} = ~900 kHz.
Table 4. Register 3 Device Setup
REGISTER 3
NAME
RESET VALUE
Bit0
ADDR<0>
1
Bit1
ADDR<1>
1
Bit2
ADDR<2>
0
Bit3
ADDR<3>
1
Bit4
ADDR<4>
0
Bit5
ILOAD_a<0>
0
Bit6
ILOAD_a<1>
0
Bit7
ILOAD_a<2>
0
Bit8
ILOAD_a<3>
0
Bit9
ILOAD_a<4>
0
Bit10
ILOAD_a<5>
0
Bit11
ILOAD_b<0>
0
Bit12
ILOAD_b<1>
0
Bit13
ILOAD_b<2>
0
Bit14
ILOAD_b<3>
0
Bit15
ILOAD_b<4>
0
Bit16
ILOAD_b<5>
0
WORKING DESCRIPTION
Register address
SPI bank address
I mixer offset side A
I mixer offset side B
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
41
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
Table 4. Register 3 Device Setup (continued)
REGISTER 3
NAME
RESET VALUE
WORKING DESCRIPTION
Bit17
QLOAD_a<0>
0
Bit18
QLOAD_a<1>
0
Bit19
QLOAD_a<2>
0
Bit20
QLOAD_a<3>
0
Bit21
QLOAD_a<4>
0
Bit22
QLOAD_a<5>
0
Bit23
QLOAD_b<0>
0
Bit24
QLOAD_b<1>
0
Bit25
QLOAD_b<2>
0
Bit26
QLOAD_b<3>
0
Bit27
QLOAD_b<4>
0
Bit28
QLOAD_b<5>
0
Bit29
Bypass
0
Engage filter bypass
Bit30
Fltr Ctrl_b<0>
1
Bit31
Fltr Ctrl_b<1>
0
Used to adjust for filter peaking response; set to 0 in bypass mode, 1
otherwise
Q mixer offset side A
Q mixer offset side B
I/Q Mixer Load A/B: These bits adjust the load on the mixer output. All values should be 0. No modification is
necessary.
Register 4: No programming required for register 4
Table 5. Register 5 Device Setup
42
REGISTER 5
NAME
RESET VALUE
Bit0
ADDR<0>
1
Bit1
ADDR<1>
0
Bit2
ADDR<2>
1
Bit3
ADDR<3>
1
Bit4
ADDR<4>
0
Bit5
MIX_GM_TRIM<0>
1
Bit6
MIX_GM_TRIM<1>
0
Bit7
MIX_LO_TRIM<0>
1
Bit8
MIX_LO_TRIM<1>
0
Bit9
LO_TRIM<0>
1
Bit10
LO_TRIM<1>
0
Bit11
MIX_BUFF_TRIM<0>
1
Bit12
MIX_BUFF_TRIM<1>
0
Bit13
FLTR_TRIM<0>
1
Bit14
FLTR_TRIM<1>
0
Bit15
OUT_BUFF_TRIM<0>
1
Bit16
OUT_BUFF_TRIM<1>
0
WORKING DESCRIPTION
Register address
SPI bank address
Mixer gm current trim
Mixer switch core VCM trim
LO buffers current trim
Mixer output buffer current trim
Filter current trim
Filter output buffer current trim
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
Table 5. Register 5 Device Setup (continued)
REGISTER 5
NAME
RESET VALUE
Bit17
0
Bit18
0
Bit19
0
Bit20
0
Bit21
0
Bit22
0
Bit23
WORKING DESCRIPTION
0
Bit24
NU
0
Bit25
0
Bit26
0
Bit27
0
Bit28
0
Bit29
0
Bit30
0
Bit31
0
Not used
Trims: the trim values allow for minor bias adjustments of internal stages. Generally it is recommended to leave
all trim values at the default value of 1. Linearity performance improvement over a small band of frequencies is
possible by selective adjustment of the trim values. Optimized intercept point within the band 2.5 GHz to 2.7 GHz
is achieved by setting trim values MIX_GM_TRIM<0,1>, MIX_LO_TRIM<0,1>, LO_TRIM<0,1>,
MIX_BUFF_TRIM<0,1>, FLTR_TRIM<0,1>, OUT_BUFF_TRIM<0,1> to: 2, 3, 0, 1, 2, 1, respectively.
Readback (Write Command)
0
0
0
1
0
Bit0
Bit1
Bit2
Bit3
Bit4
Zero Fill
Bit5
Bit6
Bit7
Bit8
Bit9
Bit10
Bit11
Bit12
Zero fill
Bit16
Bit17
Bit18
Bit19
Bit20
Bit21
Bit13
Bit14
Register address
Bit22
Bit23
Bit24
Bit25
Bit26
Bit27
Bit5
Bit6
Bit7
Bit8
Bit9
Bit10
Bit11
Bit21
Bit22
Bit23
Bit24
Bit25
Bit26
Bit15
1
Bit28
Bit29
Bit30
Bit31
Bit12
Bit13
Bit14
Bit15
Bit29
Bit30
Bit31
Reg 0:DAC/Device ID Readback
Register Address
Bit0
Bit1
Bit2
Bit16
Bit17
Bit18
SPI Bank Addr
Bit3
ID
Bit4
NU
DC offset Q DAC
Bit19
DC offset I DAC
Bit20
Bit27
Bit28
Table 6. Register 0 Device Setup (Read-Only)
READBACK REGISTER
NAME
RESET VALUE
Bit0
ADDR<0>
0
Bit1
ADDR<1>
0
Bit2
ADDR<2>
0
Bit3
ADDR<3>
1
Bit4
ADDR<4>
0
Bit5
ID<0>
1
Bit6
ID<1>
0
WORKING DESCRIPTION
Select SPI reg 1 to 5
Select SPI bank 1 to 3
Version ID: 01 = –25
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
43
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
Table 6. Register 0 Device Setup (Read-Only) (continued)
READBACK REGISTER
NAME
RESET VALUE
Bit7
0
Bit8
0
Bit9
0
Bit10
0
Bit11
NU
0
Bit12
0
Bit13
0
Bit14
0
Bit15
44
WORKING DESCRIPTION
Not used
0
Bit16
DC_OFFSET_Q<0>
0
Bit17
DC_OFFSET_Q<1>
0
Bit18
DC_OFFSET_Q<2>
0
Bit19
DC_OFFSET_Q<3>
0
Bit20
DC_OFFSET_Q<4>
0
Bit21
DC_OFFSET_Q<5>
0
Bit22
DC_OFFSET_Q<6>
0
Bit23
DC_OFFSET_Q<7>
1
Bit24
DC_OFFSET_I<0>
0
Bit25
DC_OFFSET_I<1>
0
Bit26
DC_OFFSET_I<2>
0
Bit27
DC_OFFSET_I<3>
0
Bit28
DC_OFFSET_I<4>
0
Bit29
DC_OFFSET_I<5>
0
Bit30
DC_OFFSET_I<6>
0
Bit31
DC_OFFSET_I<7>
1
DC offset DAC Q register
DC offset DAC I register
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
APPLICATION INFORMATION
Gain Control
The TRF371135 integrates a baseband programmable-gain amplifier (PGA) that provides 24 dB of gain range
with 1-dB steps. The PGA gain is controlled through SPI by a 5-bit word (register 1 bits<12,16>). Alternatively,
the PGA can be programmed by a combination of five bits programmed through the SPI and three parallel
external bits (pins Gain_B2, Gain_B1, Gain_B0). The external bits are used to reduce the PGA setting quickly
without having to reprogram the SPI registers. The fast gain control multiplier bit (register 1 bit 28) sets the step
size of each bit to either 1 dB or 2 dB. This allows a fast gain reduction of 0 dB to 7 dB in 1-dB steps or 0 dB to
14 dB in 2-dB steps.
The PGA gain control word (BBGAIN<0,4>) can be programmed to a setting between 0 and 24. This word is the
SPI programmed gain (register 1 bits<12,16>) minus the parallel external 3 bits as shown in Figure 56. Note that
the PGA gain setting rails at 0 and does not go any lower. Typical applications set the nominal PGA gain setting
to 17 and use the fast-gain control bits to protect the analog-to-digital converter in the event of a strong input
jammer signal.
Composite
PGA Setting
(min: 0, max 24)
+
SPI
X
(x1, x2)
Gain_B0
Gain_B1
Gain_B2
Fast Gain Select
B0386-01
Figure 56. PGA Gain Control Word
For example, if a PGA gain setting of 19 is desired, then the SPI can be programmed directly to a value of 19.
Alternatively, the SPI gain register can be programmed to 24 and the parallel external bits set to 101 (binary)
corresponding to 5-dB reduction.
Automated DC Offset Calibration
The TRF371135 provides an automatic calibration procedure for adjusting the dc offset in the baseband I/Q
paths. The internal calibration requires a clock in order to function. The TRF371135 can use the internal
relaxation oscillator or the external SPI clock. Using the internal oscillator is the preferred method, which is
selected by setting the Cal_clk_sel (register 2, bit 28) to 1. The internal oscillator frequency is set through the
Osc_trim bits (register 2, bits <29,31>). The frequency of the oscillator is detailed in Table 7; however, it is
expected the actual frequency of operation can vary plus or minus 35% due to process variations. The oscillator
frequency can be monitored on the READBACK pin when the Osc_test register (register 1, bit 29) is set to 1.
Table 7. Internal Oscillator Frequency Control
Osc_trim<2>
Osc_trim<1>
Osc_trim<0>
FREQUENCY
0
0
0
300 kHz
0
0
1
500 kHz
0
1
0
700 kHz
0
1
1
900 kHz
1
0
0
1.1 MHz
1
0
1
1.3 MHz
1
1
0
1.5 MHz
1
1
1
1.8 MHz
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
45
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
The default setting of these registers corresponds to a 900-kHz oscillator frequency. This is sufficient for
autocalibration; modification is not required except for faster calibration convergence.
The output full-scale range of the internal dc offset correction DACs is programmable (IDET_B<0,1>, register 2
bits<22,23>). The range is shown in Table 8.
Table 8. DC Offset Correction DAC Programmable Range
IDET_B0
IDET_B1
Full Scale
0
0
50 µA
0
1
100 µA
1
0
150 µA
1
1
200 µA
The I- and Q-channel output maximum dc offset correction range can be calculated by multiplying the values in
the table by the baseband PGA gain. The LSB of the digital correction is dependent on the programmed
maximum correction range. For optimum resolution and best correction, the dc offset DAC range should be set to
50 µA with the PGA gain set for the nominal condition. The dc offset correction DAC output is affected by a
change in the PGA gain, but if the initial calibration yields optimum results, then the adjustment of the PGA gain
during normal operation does not significantly impair the dc offset balance. For example, if the optimized
calibration yields a dc offset balance of 2 mV at a gain setting of 17, then the dc offset maintains less than 10 mV
balance as the gain is adjusted ±7 dB.
The dc offset correction DACs are programmed from the internal registers when the CAL_SEL bit (register 2, bit
24) is set to 1. At start-up, the internal registers are loaded at half-scale, corresponding to a decimal value of
128. The auto-cal is initiated by toggling the EN_AUTOCAL bit (register 2, bit 5) to 1. When the calibration is
over, this bit is automatically reset to 0. During calibration, the RF local oscillator must be applied. The dc offset
DAC state is stored in the internal registers and maintained as long as the power supply is kept on or until a new
calibration is started.
The required clock speed for the optimum calibration is determined by the internal detector behavior (integration
bandwidth, gain, sensitivity). The input bandwidth of the detector can be adjusted by changing the cutoff
frequency of the RC low-pass filter in front of the detector (register 1, bits 25–26). EN_FLT_B0 controls the
resistor (bypass = 1) and EN_FLT_B1 controls the capacitor (bypass = 1). The typical 3-dB cutoff frequencies of
the detector bandwidth are summarized in Table 9. The speed of the clock can be slowed down by selecting a
clock divider ratio (register 2, bits 25–27).
Table 9. Detector Bandwidth Settings
EN_FLT_B1
EN_FLT_B0
TYPICAL 3-dB CUTOFF FREQUENCY
NOTES
X
0
10 MHz
Maximum bandwidth, bypass R, C
0
1
10 kHz
Enable R
1
1
1 kHz
Minimum bandwidth, enable R, C
The detector has more averaging time with a slower clock; hence, it is desirable to slow down the clock speed for
a given condition to achieve optimum results. For example, if there is no RF present on the RF input port, the
detection filter can be left wide (10 MHz) and the clock divider can be left at div-by-128. The autocalibration
yields a dc offset balance between the differential baseband output ports (I and Q) that is less than 15 mV. Some
minor improvement may be obtained by increasing the averaging of the detector by increasing the clock divider
up to 256 or 1024.
On the other hand, if there is a modulated RF signal present at the input port, it is desirable to reduce the
detector bandwidth to filter out most of the modulated signal. The detector bandwidth can be set to a 1-kHz
corner frequency. With the modulated signal present and with the detection bandwidth reduced, additional
averaging is required to get the optimum results. A clock divider setting of 1024 yields optimum results.
Of course, an increase in the averaging is possible by increasing the clock divider at the expense of longer
converging time. The convergence time can be calculated by the following:
(Auto_Cal_Clk_Cycles) ´ (Clk_Divider)
tc =
Osc_Freq
(1)
46
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
The dc offset calibration converges in approximately nine cycles. For the case with a clock divider of 1024 and
with the nominal oscillator frequency of 900 kHz, the convergence time is:
(9) ´ (1024)
tc =
= 10.24 ms
900 kHz
(2)
Alternate Method for Adjusting DC Offset
The internal registers controlling the internal dc current DAC are accessible through the SPI, providing a
user-programmable method for implementing the dc offset calibration. To employ this option the CAL_SEL bit
must be set to 0. During this calibration, an external instrument monitors the output dc offset between the I/Q
differential outputs and programs the internal registers (IDAC_BIT<0,7> and QDAC_BIT<0,7> bits) to cancel the
dc offset.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
47
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
PCB Layout Guidelines
The TRF371135 device is fitted with a ground slug on the back of the package that must be soldered to the PCB
ground with adequate ground vias to ensure a good thermal and electrical connection. The recommended via
pattern and ground pad dimensions are shown in Figure 57. The recommended via diameter is 8 mils (0.2 mm).
The ground pins of the device can be directly tied to the ground slug pad for a low-inductance path to ground.
Additional ground vias may be added if space allows. The no-connect (NC) pins can also be tied to the ground
plane.
Decoupling capacitors at each of the supply pins is recommended. The high-frequency decoupling capacitors for
the RF mixers (VCCMIX) should be placed close to their respective pins. The value of the capacitor should be
chosen to provide a low-impedance RF path to ground at the frequency of operation. Typically, this value is
around 10 pF or lower. The other decoupling capacitors at the other supply pins should be kept as close to their
respective pins as possible.
The device exhibits symmetry with respect to the quadrature output paths. It is recommended that the PCB
layout maintain that symmetry in order to ensure the quadrature balance of the device is not impaired. The I/Q
output traces should be routed as differential pairs and their lengths all kept equal to each other. Decoupling
capacitors for the supply pins should be kept symmetrical where possible. The RF differential input lines related
to the RF input and the LO input should also be routed as differential lines with their respective lengths kept
equal. If an RF balun is used to convert a single-ended input to a differential input, then the RF balun should be
placed close to the device. Implement the RF balun layout per the manufacturer’s guidelines to provide best gain
and phase balance to the differential outputs. On the RF traces, maintain proper trace widths to keep the
characteristic impedance of the RF traces at a nominal 50 Ω.
0.200 (5.08)
0.025 (0.635)
Ø0.008 (0.203)
0.025 (0.635)
0.0125 (0.318)
0.200 (5.08)
Note: Dimensions are in inches (mm)
M0177-01
Figure 57. PCB Layout Guidelines
48
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
Application Schematic
The typical application schematic is shown in Figure 58. The RF bypass capacitors and coupling capacitors on
the supply pins should be adjusted to provide the best high-frequency bypass based on the frequency of
operation.
To Microcontroller
RFin
READBACK
NC
Gain_B2
Gain_B1
Gain_B0
NC
NC
MIXIoutn
STROBE
MIXIoutp
DATA
CLOCK
To Microcontroller
48 47 46 45 44 43 42 41 40 39 38 37
36
GNDDIG
1
VCCDIG
2
35
GND
CHIP_EN
3
34
BBIoutn
VCCMIX1
4
33
BBIoutp
GND
5
32
GND
MIXinp
6
31
LOip
VCCBBI
To ADC I
LOin
TRF371135
MIXinn
7
30
LOin
GND
8
29
VCCLO
VCCMIX2
9
28
BBQoutp
NC
10
27
BBQoutn
NC
11
26
GND
To ADC Q
VCCBBQ
NC
VCM
GNDBIAS
VCCBIAS
REXT
NC
NC
MIXQoutn
GND
MIXQoutp
GND
GND
25
12
13 14 15 16 17 18 19 20 21 22 23 24
GND
30 kW
Figure 58. TRF371135 Application Schematic
The RF input port and the RF LO port require differential input paths. Single-ended RF inputs to these ports can
be converted with an RF balun that is centered at the band of interest. Linearity performance of the TRF371135
is dependent on the amplitude and phase balance of the RF balun; hence, care should be taken with the
selection of the balun device and with the RF layout of the device. The recommended RF balun devices are
listed in Table 10.
Table 10. RF Balun Devices
MANUFACTURER
PART NUMBER
FREQUENCY RANGE
UNBALANCE IMPEDANCE
BALANCE IMPEDANCE
Murata
LDB211G8005C-001
1800 MHz ±100 MHz
50 Ω
50 Ω
Murata
LDB211G9005C-001
1900 MHz ±100 MHz
50 Ω
50 Ω
Murata
LDB212G4005C-001
2.3 GHz to 2.7 GHz
50 Ω
50 Ω
Johanson
3600BL14M050E
3.3 GHz to 3.8 GHz
50 Ω
50 Ω
Johanson
5400BL15B050E
4.9 GHz to 5.9 GHz
50 Ω
50 Ω
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
49
TRF371135
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
www.ti.com
Application for a High-Performance RF Receiver Signal Chain
The TRF371135 is the centerpiece component in a high-performance direct-downconversion receiver. The
device is a highly integrated direct-downconversion demodulator that requires minimal additional devices to
complete the signal chain. A signal chain block diagram example is shown in Figure 59.
ADS62P42
TRF371135
14
0
90
LNA
14
TRF3761
Figure 59. Block Diagram of Direct-Downconvert Receiver
The lineup requires a low-noise amplifier (LNA) that operates at the frequency of interest with typical 1- to 2-dB
noise figure (NF) performance. An RF band-pass filter (BPF) is selected at the frequency band of interest to
eliminate unwanted signals and images outside the band from reaching the demodulator. The TRF371135
incorporates the direct-downconvert demodulation, baseband filtering, and baseband gain-control functions. An
external synthesizer, such as the TRF3761, is used to provide the local oscillator (LO) source to the TRF371135.
The differential outputs of the TRF3761 directly mate with LO input of the TRF371135. The quadrature outputs
(I/Q) of the TRF371135 directly drive the input to the analog-to-digital converter (ADC). A dual ADC like the
ADS62P42 14-bit 65-MSPS ADC mates perfectly with the differential I/Q output of the TRF371135. The
baseband output pins (pins 27, 28, 33, 34) can be connected directly to the corresponding input pins of typical
ADCs. The positive and negative terminal connections between the TRF371135 and the ADC can be swapped to
facilitate a clean routing layout. The swapped connection can be reversed by flipping the signals in the digital
domain, if desired. In addition, the common-mode output voltage generated by the ADC is fed directly into the
common-mode port (pin 24) to ensure the optimum dynamic range of the ADC is maintained.
EVALUATION TOOLS
An evaluation module is available to test the TRF371135 performance. The TRF371135EVM can be configured
with different baluns to enable operation in various frequency bands. The TRF371135EVM is available for
purchase through the Texas Instruments web site at www.ti.com.
50
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
TRF371135
www.ti.com
SLWS220A – FEBRUARY 2010 – REVISED MARCH 2010
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (February, 2010) to Revision A
Page
•
Corrected product name discussed throughout document ................................................................................................... 1
•
Added Evaluation Tools ...................................................................................................................................................... 50
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): TRF371135
51
PACKAGE OPTION ADDENDUM
www.ti.com
22-Mar-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TRF371135IRGZR
ACTIVE
VQFN
RGZ
48
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TRF371135IRGZT
ACTIVE
VQFN
RGZ
48
250
CU NIPDAU
Level-2-260C-1 YEAR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated