ZILOG Z86L8708VSC

PRELIMINARY PRODUCT SPECIFICATION
1
Z86L88/81/86/87/89/73
1
IR/LOW-VOLTAGE MICROCONTROLLER
FEATURES
Device
ROM
(KB)
RAM*
(Bytes)
I/O
Lines
Voltage
Range
Z86L88
Z86L81
Z86L86
Z86L87
Z86L89
Z86L73
16
24
32
16
24
32
237
237
237
236
236
236
23
23
23
31
31
31
2.0V to 3.9V
2.0V to 3.9V
2.0V to 3.9V
2.0V to 3.9V
2.0V to 3.9V
2.0V to 3.9V
–
Programmable Input Glitch Filter for Pulse
Reception
■
Five Priority Interrupts
– Three External
– Two Assigned to Counter/Timers
■
Low Voltage Detection and Standby Mode
■
Programmable Watch-Dog/Power-On Reset Circuits
■
Two Independent Comparators with Programmable
Interrupt Polarity
■
On-Chip Oscillator that Accepts a Crystal, Ceramic
Resonator, LC, RC (Mask Option), or External Clock
Drive
■
Mask Selectable 200 kOhms Pull-Ups on Ports 0, 2, 3
– All Eight Port 2 Bits at One Time or Not
– Pull-Ups Automatically Disabled Upon Selecting
Individual Pins as Outputs.
■
Maskable Mouse/Trackball Interface on P00 Through
P03.
■
32 kHz Oscillator Mask Option
Note: *General-Purpose
■
Low Power Consumption - 40 mW (Typical)
■
Three Standby Modes
– STOP
– HALT
– Low Voltage
■
Special Architecture to Automate Both Generation and
Reception of Complex Pulses or Signals:
– One Programmable 8-Bit Counter/Timer with Two
Capture Registers
– One Programmable 16-Bit Counter/Timer with
One 16-Bit Capture Register
GENERAL DESCRIPTION
The Z86LXX family of IR (Infrared) CCP™ (Consumer Controller Processor) Controllers are ROM/ROMless-based
members of the Z8® single-chip microcontroller family with
256 bytes of internal RAM. The differentiating factor between these devices is the availability of ROM, and package options. For the 40 and 44-pin devices the use of external memory enables these Z8 microcontrollers to be
used where code flexibility is required. Zilog’s CMOS microcontrollers offers fast executing, efficient use of memory, sophisticated interrupts, input/output bit manipulation
capabilities, automated pulse generation/reception, and inDS96LV00800
ternal key-scan pull-up resistors. The Z86LXX product line
offers easy hardware/software system expansion cost-effective and low power consumption.
The Z86LXX architecture is based on Zilog's 8-bit microcontroller core with an Expanded Register File to allow access to register mapped peripherals, I/O circuits, and powerful counter/timer circuitry. The CCP offers a flexible I/O
scheme, an efficient register and address space structure,
and a number of ancillary features that are useful in many
PRELIMINARY
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
GENERAL DESCRIPTION (Continued)
consumer, automotive, computer peripheral, and battery
operated hand-held applications.
There are four basic address spaces available to support
a wide range of configurations: Program Memory, Register File, Expanded Register File, and External Memory.
The register file is composed of 256 bytes of RAM. It includes four I/O port registers, 16 control and status registers and the rest are General Purpose registers. The Expanded Register File consists of two additional register
groups (F and D). External Memory is not available on 28pin versions.
with 8-bit and 16-bit counter/timers (Figure 1). Also included are a large number of user-selectable modes, and two
on-board comparators to process analog signals with separate reference voltages (Figure 2).
Notes: All Signals with a preceding front slash, "/", are active Low, e.g., B//W (WORD is active Low); /B/W (BYTE is
active Low, only).
Power connections follow conventional descriptions below:
To unburden the program from coping with such real-time
problems as generating complex waveforms or receiving
and demodulating complex waveform/pulses, the Z86LXX
family offers a new intelligent counter/timer architecture
Connection
Circuit
Device
Power
VCC
VDD
Ground
GND
VSS
HI16
LO16
8
8
16-Bit
T16
Timer 16
16
1 2 4 8
8
SCLK
Clock
Divider
8
TC16H
TC16L
And/Or
Logic
HI8
LO8
8
8
Input
Glitch
Filter
Timer 8/16
Edge
Detect
Circuit
8-Bit
T8
Timer 8
8
8
TC8H
TC8L
Figure 1. Counter/Timers Diagram
2
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
P00
P01
P02
P03
Pref1
P31
P32
P33
Register File
256 x 8-bit
4
Port 0
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
I/O Bit
Programmable
P20
P21
P22
P23
P24
P25
P26
P27
Port 3
Register Bus
Internal
Address Bus
4
ROM
24K/32K x 8
1
P34
P35
P36
P37
Z8 Core
Internal Data Bus
8
Port 1
Expanded
Register
File
Expanded
Register Bus
Machine
Timing
&
Instruction
Control
XTAL
/AS
/DS
R/W
/RESET
R//RL
(44-Pin)
Power
Port 2
Counter/Timer 8
8-Bit
VDD
VSS
Counter/Timer 16
16-Bit
Figure 2. Functional Block Diagram
DS96LV00800
PRELIMINARY
3
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN DESCRIPTION
1
P25
P26
P27
P04
P05
P06
P07
VDD
XTAL2
XTAL1
P31
P32
P33
P34
28
P24
P23
P22
P21
P20
P03
VSS
P02
P01
P00
Pref1
P36
P37
P35
Z86L88/86/81
DIP
14
15
Figure 3. 28-Pin DIP
Pin Assignments
P25
P26
P27
P04
P05
P06
P07
VDD
XTAL2
XTAL1
P31
P32
P33
P34
1
28
Z86L88/86/81
SOIC
14
15
P24
P23
P22
P21
P20
P03
VSS
P02
P01
P00
Pref1
P36
P37
P35
Figure 4. 28-Pin SOIC
Pin Assignments
4
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
1
R//W
P25
P26
P27
P04
P05
P06
P14
P15
P07
VDD
P16
P17
XTAL2
XTAL1
P31
P32
P33
P34
/AS
40
/DS
P24
P23
P22
P21
P20
P03
P13
P12
VSS
P02
P11
P10
P01
P00
Pref1
P36
P37
P35
/RESET
Z86L73/89/87
DIP
20
21
1
P20
P03
P13
P12
VSS
VSS
P02
P11
P10
P01
P00
Figure 5. 40-Pin DIP
Pin Assignments
6
1
7
40
39
Z86L73/89/73
PLCC
17
29
28
18
Pref1
P36
P37
P35
/RESET
VSS
/AS
P34
P33
P32
P31
P05
P06
P14
P15
P07
VDD
VDD
P16
P17
XTAL2
XTAL1
P21
P22
P23
P24
/DS
R//RL
R//W
P25
P26
P27
P04
Figure 6. 44-Pin PLCC
Pin Assignments
DS96LV00800
PRELIMINARY
5
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
P20
P03
P13
P12
VSS
VSS
P02
P11
P10
P01
P00
PIN DESCRIPTION (Continued)
33
P21
P22
P23
P24
/DS
R//RL
R//W
P25
P26
P27
P04
23
22
34
Z86L73/89/87
QFP
12
11
44
P05
P06
P14
P15
P07
VDD
VDD
P16
P17
XTAL2
XTAL1
1
Pref1
P36
P37
P35
/RESET
VSS
/AS
P34
P33
P32
P31
Figure 7. 44-Pin QFP
Pin Assignments
6
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Table 1. Pin Identification
40-Pin
DIP #
44-Pin
PLCC #
44-Pin
QFP #
Symbol
26
27
30
34
5
6
7
10
28
29
32
33
8
9
12
13
35
36
37
38
39
2
3
4
16
17
18
19
22
24
23
20
40
1
21
15
14
11
40
41
44
5
17
18
19
22
42
43
3
4
20
21
25
26
6
7
8
9
10
14
15
16
29
30
31
32
36
38
37
33
11
13
35
28
27
23,24
23
24
27
32
44
1
2
5
25
26
30
31
3
4
8
9
33
34
35
36
37
41
42
43
12
13
14
15
19
21
20
16
38
40
18
11
10
6,7
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
P24
P25
P26
P27
P31
P32
P33
P34
P35
P36
P37
/AS
/DS
R//W
/RESET
XTAL1
XTAL2
VDD
31
1,2, 34
17,28,29
VSS
25
39
12
22
39
Pref1
R//RL
DS96LV00800
Direction
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input
Input
Input
Output
Output
Output
Output
Output
Output
Output
Input
Input
Output
1
Description
Port 0 is Nibble Programmable.
Port 0 can be configured as
A15-A8 external program
ROM Address Bus.
Port 0 can be configured as a
mouse/trackball input.
Port 1 is byte programmable.
Port 1 can be configured as
multiplexed A7-A0/D7-D0
external program ROM
Address/Data Bus.
Port 2 pins are individually
configurable as input or output.
IRQ2/Modulator input
IRQ0
IRQ1
T8 output
T16 output
T8/T16 output
Address Strobe
Data Strobe
Read/Write
Reset
Crystal, Oscillator Clock
Crystal, Oscillator Clock
Power Supply
Ground
Input
Input
PRELIMINARY
Comparator 1 Reference
ROM/ROMless
7
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN DESCRIPTION (Continued)
Table 2. Pin Identification
8
28-Pin
DIP & SOIC
Symbol
Direction
19
20
21
23
4
5
P00
P01
P02
P03
P04
P05
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
6
7
24
25
26
27
28
1
2
3
18
11
12
13
14
15
17
16
10
9
8
P06
P07
P20
P21
P22
P23
P24
P25
P26
P27
Pref1
P31
P32
P33
P34
P35
P36
P37
XTAL1
XTAL2
VDD
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input
Input
Input
Input
Output
Output
Output
Output
Input
Output
22
VSS
Description
Port 0 is Nibble Programmable
Port 0 can be configured as
A15-A8 external program
ROM Address Bus.
Port 0 can be configured as a
mouse/trackball input.
Port 2 pins are individually
configurable as input or output.
Analog Ref Input
IRQ2/Modulator input
IRQ0
IRQ1
T8 output
T16 output
T8/T16 output
Crystal, Oscillator Clock
Crystal, Oscillator Clock
Power Supply
Ground
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
TSTG
TA
Description
Min
Max
Units
Supply Voltage
(*)
Storage Temp.
–0.3
+7.0
V
–65°
+150°
C
†
C
Oper. Ambient
Temp.
Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; operation of the device at
any condition above those indicated in the operational sections of these specifications is not implied. Exposure to absolute maximum rating conditions for an extended period
may affect device reliability.
Notes: :
* Voltage on all pins with respect to GND.
† See Ordering Information.
STANDARD TEST CONDITIONS
The characteristics listed below apply for standard test
conditions as noted. All voltages are referenced to GND.
Positive current flows into the referenced pin (Figure 8).
From Output
Under Test
I
150 pF
Figure 8. Test Load Diagram
CAPACITANCE
TA = 25°C, VCC = GND = 0V, f = 1.0 MHz, unmeasured pins returned to GND.
Parameter
Max
Input capacitance
Output capacitance
I/O capacitance
12 pF
12 pF
12 pF
DS96LV00800
PRELIMINARY
9
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
DC CHARACTERISTICS
Preliminary
TA = 0°C to +70°C
Sym
Parameter
VCC
Min
Max Input Voltage 2.0V
3.9V
VCH
VCL
Clock Input
High Voltage
Clock Input
Low Voltage
Max
Typ @
25°C
Units
Conditions
7
7
V
V
IIN <250 µA
IIN <250 µA
Driven by External
Clock Generator
Driven by External
Clock Generator
Driven by External
Clock Generator
Driven by External
Clock Generator
2.0V
0.8 VCC
VCC + 0.3
V
3.9V
0.8 VCC
VCC + 0.3
V
2.0V
VSS – 0.3
0.2 VCC
V
3.9V
VSS– 0.3
0.2 VCC
V
VIH
Input High Voltage 2.0V
3.9V
0.7 VCC
0.7 VCC
VCC + 0.3
VCC + 0.3
0.5VCC
0.5VCC
V
V
VIL
Input Low Voltage 2.0V
3.9V
VSS – 0.3
VSS – 0.3
0.2 VCC
0.2 VCC
0.5VCC
0.5VCC
V
V
VOH1
Output High
Voltage
2.0V
3.9V
VCC – 0.4
VCC – 0.4
1.7
3.7
V
V
IOH = –0.5 mA
IOH = –0.5 mA
VOH2
Output High
Voltage (P36,
P37,P00, P01)
Output Low
Voltage
2.0V
3.9V
VCC - 0.8
VCC - 0.8
V
V
IOH = –7 mA
IOH = –7 mA
2.0V
3.9V
0.4
0.4
0.1
0.2
V
V
IOL = 1.0 mA
IOL = 4.0 mA
Output Low
Voltage
2.0V
0.8
0.5
V
IOL = 5.0 mA
3.9V
0.8
0.3
V
IOL = 7.0 mA
0.8
0.8
0.3
0.2
V
V
IOL = 10 mA
IOL = 10 mA
VOL1
VOL2*
VOL2
Output Low
Voltage(P36,
P37,P00,P01)
2.0V
3.9V
VRH
Reset Input
High Voltage
2.0V
3.9V
0.8 VCC
0.8 VCC
VCC
VCC
1.5
2.0
V
V
VRl
Reset Input
Low Voltage
2.0V
3.9V
VSS – 0.3
VSS – 0.3
0.2 VCC
0.2 VCC
0.5
0.9
V
V
VOFFSET
Comparator Input 2.0V
Offset Voltage
3.9V
Input Leakage
2.0V
3.9V
-1
-1
25
25
1
1
10
10
<1
<1
mV
mV
µA
µA
VIN = OV, VCC
VIN = OV, VCC
–1
–1
1
1
<1
<1
µA
µA
VIN = OV, VCC
VIN = OV, VCC
IIL
IOL
Output Leakage
IIR
Reset Input Pull- 2.0V
Up Current
3.9V
–230
–400
-90
–220
µA
µA
VIN = OV
VIN = OV‘
ICC
Supply Current
10
15
250
850
4
10
100
500
mA
mA
µA
µA
@ 8.0 MHz
@ 8.0 MHz
@ 32 kHz
@ 32 kHz
10
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
PRELIMINARY
Notes
1,2
1,2
1,2,7
1,2,7
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
TA = 0°C to +70°C
Sym
ICC1
ICC2
Parameter
Standby Current
(WDT Off)
Standby Current
TPOR
Power-On Reset
Vram
Static RAM Data
Retention Voltage
VCC Low Voltage
Protection
ICC1
Crystal/Resonator
VLV
(Vbo)
Notes:
External Clock Drive
VCC
Max
25°C
Units
2.0V
3
1
mA
3.9V
5
4
mA
2.0V
2
0.8
mA
3.9V
4
2.5
mA
2.0V
8
2
µA
3.9V
10
3
µA
2.0V
3.9V
500
800
310
600
µA
µA
75
20
18
7
0.5
ms
ms
V
2.15
1.7
V
2.0V
3.9V
Vram
Min
Typ @
12
5
0.8
Typ
3.0 mA
Max
5
Unit
mA
Frequency
8.0 MHz
0.3 mA
5
mA
8.0 MHz
Conditions
HALT Mode
VIN = OV, VCC @
8.0 MHz
HALT Mode
VIN = OV, VCC
@ 8.0 MHz
Clock Divide-by16 @ 8.0 MHz
Clock Divide-by16 @ 8.0 MHz
STOP Mode
VIN = OV, VCC
WDT is not
Running
STOP Mode
VIN = OV, VCC
WDT is not
Running
STOP Mode
VIN = OV, VCC
WDT is Running
Notes
1,2
1,2
1,2
1,2
3,5
3,5
3,5
6
8 MHz max
Ext. CLK Freq.
4
1. All outputs unloaded, inputs at rail.
2. CL1 = CL2 = 100 pF
3. Same as note [4] except inputs at VCC.
4. The VLV increases as the temperature decreases.
5. Oscillator stopped.
6. Oscillator stops when VCC falls below Vlv limit
7. 32 kHz clock driver input.
* All Outputs excluding P00, P01, P36, and P37.
DS96LV00800
PRELIMINARY
11
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
External I/O or Memory Read and Write Timing Diagram
R//W
13
12
19
Port 0, /DM
16
18
Port 1
20
3
A7 - A0
1
D7 - D0 IN
2
9
/AS
8
11
4
5
/DS
(Read)
6
17
10
Port 1
A7 - A0
D7 - D0
OUT
14
15
7
/DS
(Write)
Figure 9. External I/O or Memory Read/Write Timing
12
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
Preliminary
External I/O or Memory Read and Write Timing Table
1
TA = 0°C to +70°C
8.0MHz
No
Symbol
Parameter
1
TdA(AS)
Address Valid to
/AS Rising Delay
/AS Rising to Address
Float Delay
/AS Rising to Read
Data Required Valid
/AS Low Width
2
TdAS(A)
3
TdAS(DR)
4
TwAS
5
Td
6
TwDSR
Address Float to
/DS Falling
/DS (Read) Low Width
7
TwDSW
/DS (Write) Low Width
8
TdDSR(DR)
9
ThDR(DS)
10
TdDS(A)
11
TdDS(AS)
12
TdR/W(AS)
13
TdDS(R/W)
14
TdDW(DSW)
15
TdDS(DW)
16
TdA(DR)
17
TdAS(DS)
18
TdDM(AS)
19
TdDS(DM)
20
ThDS(A)
/DS Falling to Read
Data Required Valid
Read Data to /DS Rising
Hold Time
/DS Rising to Address
Active Delay
/DS Rising to /AS
Falling Delay
R//W Valid to /AS
Rising Delay
/DS Rising to
R//W Not Valid
Write Data Valid to /DS
Falling (Write) Delay
/DS Rising to Write
Data Not Valid Delay
Address Valid to Read
Data Required Valid
/AS Rising to
/DS Falling Delay
/DM Valid to /AS
Falling Delay
/DS Rise to
/DM Valid Delay
/DS Rise to Address
Valid Hold Time
VCC
Min
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
55
55
70
70
Max
400
400
80
80
0
0
300
300
165
165
260
260
0
0
85
95
60
70
70
70
70
70
80
80
70
80
475
475
100
100
55
55
70
70
70
70
Units
Notes
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
2
2
2
1,2
2
1,2
1,2
1,2
2
2
2
2
2
2
2
1,2
2
2
Notes:
1. When using extended memory timing add 2 TpC.
2. Timing numbers given are for minimum TpC.
Standard Test Load
All timing references use 0.9 VCC for a logic 1 and 0.1 VCC for a logic 0.
DS96LV00800
PRELIMINARY
13
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
Additional Timing Diagram
3
1
Clock
2
7
T
2
3
7
IN
4
5
6
IRQ N
8
9
Clock
Setup
11
Stop
Mode
Recovery
Source
10
Figure 10. Additional Timing
14
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
Preliminary
Additional Timing Table
1
TA = 0°C to +70°C
8.0MHz
No
Sym
Parameter
VCC
Min
Max
Units
Notes
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
121
121
DC
DC
25
25
ns
ns
ns
ns
ns
ns
ns
ns
100
100
ns
ns
ns
ns
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1,2
1,2
1,3
1,3
1,2
1,2
7
7
6
6
4
4
1
TpC
Input Clock Period
2
TrC,TfC
3
TwC
Clock Input Rise
and Fall Times
Input Clock Width
4
TwTinL
5
TwTinH
6
TpTin
7
TrTin,TfTin
8A
TwIL
8B
TwIL
9
TwIH
10
Twsm
11
Tost
12
Twdt
Timer Input
Low Width
Timer Input
High Width
Timer Input
Period
Timer Input Rise
and Fall Timers
Interrupt Request
Low Time
Interrupt Request
Low Time
Interrupt Request
Input High Time
Stop-Mode Recovery
Width Spec
Oscillator
Start-Up Time
Watch-Dog Timer
Delay Time (5 ms)
(10 ms)
(20 ms)
(80 ms)
37
37
100
70
3TpC
3TpC
8TpC
8TpC
100
70
5TpC
5TpC
5TpC
5TpC
12
12
5 TpC
5 TpC
12
5
25
10
50
20
225
80
ns
ns
ns
ns
5TpC
5TpC
75
20
150
40
300
80
1200
320
ms
ms
ms
ms
ms
ms
ms
ms
Notes:
1. Timing Reference uses 0.9 VCC for a logic 1 and 0.1 VCC for a logic 0.
2. Interrupt request through Port 3 (P33-P31).
3. Interrupt request through Port 3 (P30).
4. SMR – D5 = 0
DS96LV00800
PRELIMINARY
15
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
Handshake Timing Diagrams
Data In
Data In Valid
Next Data In Valid
2
1
3
/DAV
(Input)
Delayed DAV
5
4
RDY
(Output)
6
Delayed RDY
Figure 11. Port Input Handshake Timing
Data Out
Next Data Out Valid
Data Out Valid
7
/DAV
(Output)
Delayed DAV
8
9
11
10
RDY
(Input)
Delayed
RDY
Figure 12. Port Output Handshake Timing
16
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
AC CHARACTERISTICS
Preliminary
Handshake Timing Table
1
TA = 0°C to +70°C
No
Sym
Parameter
1
TsDI(DAV)
Data In Setup Time
2
ThDI(DAV)
Data In Hold Time
3
TwDAV
Data Available Width
4
TdDAVI(RDY)
5
TdDAVId(RDY)
6
TdRDYO(DAV)
7
TdDO(DAV)
8
TdDAV0(RDY)
9
TdRDY0(DAV)
10
TwRDY
DAV Falling to RDY
Falling Delay
DAV Rising to RDY
Falling Delay
RDY Rising to DAV
Falling Delay
Data Out to DAV
Falling Delay
DAV Falling to RDY
Falling Delay
RDY Falling to DAV
Rising Delay
RDY Width
11
TdRDY0d(DAV)
DS96LV00800
RDY Rising to DAV
Falling Delay
VCC
Min
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
2.0V
3.9V
0
0
0
0
155
110
PRELIMINARY
Max
160
115
120
80
0
0
63
63
0
0
160
115
110
80
110
80
Data
Direction
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
17
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN FUNCTIONS
/DS (Output, active Low). Data Strobe is activated once for
each external memory transfer. For a READ operation,
data must be available prior to the trailing edge of /DS. For
WRITE operations, the falling edge of /DS indicates that
output data is valid.
/AS (Output, active Low). Address Strobe is pulsed once
at the beginning of each machine cycle. Address output is
through Port 0/Port 1 for all external programs. Memory
address transfers are valid at the trailing edge of /AS. Under program control, /AS is placed in the high-impedance
state along with Ports 0 and 1, Data Strobe, and
Read/Write.
XTAL1 Crystal 1 (time-based input). This pin connects a
parallel-resonant crystal, ceramic resonator, LC, or RC
network or an external single-phase clock to the on-chip
oscillator input.
XTAL2 Crystal 2 (time-based output). This pin connects a
parallel-resonant, crystal, ceramic resonant, LC, or RC
network to the on-chip oscillator output.
R//W Read/Write (output, write Low). The R//W signal is
Low when the CCP is writing to the external program or
data memory.
R//RL (input). This pin, when connected to GND, disables
the internal ROM and forces the device to function as a
ROMless Z8. (Note that, when left unconnected or pulled
high to VCC, the part functions normally as a Z8 ROM version.)
Port 0 (P07-P00). Port 0 is an 8-bit, bidirectional, CMOS
compatible port. These eight I/O lines are configured under software control as a nibble I/O port, or as an address
port for interfacing external memory. The output drivers
are push-pull. Port 0 can be placed under handshake control. In this configuration, Port 3, lines P32 and P35 are
used as the handshake control /DAV0 and RDY0. Handshake signal function is dictated by the I/O direction of the
Port 0 upper nibble P07-P04. The lower nibble must have
the same direction as the upper nibble.
For external memory references, Port 0 can provide address bits A11-A8 (lower nibble) or A15-A8 (lower and upper nibble) depending on the required address space. If
the address range requires 12 bits or less, the upper nibble
of Port 0 can be programmed independently as I/O while
the lower nibble is used for addressing. If one or both nibbles are needed for I/O operation, they must be configured
by writing to the Port 0 mode register. After a hardware reset, Port 0 is configured as an input port.
Port 0 is set in the high-impedance mode (if selected as an
address output) along with Port 1 and the control signals
/AS, /DS, and R//W through P3M bits D4 and D3(Figure
13).
A ROM mask option is available to program 0.4 VDD
CMOS trip inputs on P00-P03. This allows direct interface
to mouse/trackball IR sensors.
An optional 200 kOhms pull-up is available as a mask option on all Port 0 bits with nibble select.
Note: Internal pull-ups are disabled on any given pin or
group of port pins when programmed into output mode.
18
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
1
4
Port 0 (I/O or A15 - A8)
Z86LXX
MCU
4
Optional
Handshake Controls
/DAV0 and RDY0
(P32 and P35)
Mask
Option
OEN
200 kΩ
PAD
Out
In
In
0.4 VDD
Trip Point Buffer
* Mask Selectable
Refer to the Z86C17 specification for
application information in utilizing these
inputs in a mouse or trackball application.
Figure 13. Port 0 Configuration
DS96LV00800
PRELIMINARY
19
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN FUNCTIONS (Continued)
Port 1 (P17-P10). Port 1 is a multiplexed Address (A7-A0)
and Data (D7-D0), CMOS compatible port. Port 1 is dedicated to the Zilog ZBus®-compatible memory interface.
The operations of Port 1 are supported by the Address
Strobe (/AS) and Data Strobe (/DS) lines, and by the
Read/Write (R//W) and Data Memory (/DM) control lines.
Data memory read/write operations are done through this
port (Figure 14). If more than 256 external locations are required, Port 0 outputs the additional lines.
Port 1 can be placed in the high-impedance state along
with Port 0, /AS, /DS, and R//W, allowing the Z86LXX to
share common resources in multiprocessor and DMA applications. Port1 can also be configured for standard port
output mode..
Port 1
(I/O or AD7 - AD0)
8
Z86LXX
MCU
Optional
Handshake Controls
/DAV1 and RDY1
(P33 and P34)
OEN
PAD
Out
In
Auto Latch
R ≈ 500 KΩ
Figure 14. Port 1 Configuration
20
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Port 2 (P27-P20). Port 2 is an 8-bit, bidirectional, CMOS
compatible I/O port. These eight I/O lines can be independently configured under software control as inputs or outputs. Port 2 is always available for I/O operation. A mask
option is available to connect eight 200 kOhms (±50%)
pull-up resistors on this port. Bits programmed as outputs
are globally programmed as either push-pull or opendrain. Port 2 may be placed under handshake control. In
this configuration, Port 3 lines, P31 and P36 are used as
the handshake controls lines /DAV2 and RDY2. The hand-
shake signal assignment for Port 3, lines P31 and P36 is
dictated by the direction (input or output) assigned to Bit 7,
Port 2 (Figure 15). The CCP POR resets with the eight bits
of Port 2 configured as inputs with open-drain outputs.
Port 2 also has an 8-bit input OR and an AND gate which
can be used to wake up the part (Figure 41). P20 can be
programmed to access the edge selection circuitry (Figure
24).
Port 2 (I/O)
Z86LXX
MCU
Optional
Handshake Controls
/DAV2 and RDY2
(P31 and P36)
VCC
Open-Drain
200 kΩ
OEN
Mask
Option
PAD
Out
In
Figure 15. Port 2 Configuration
DS96LV00800
PRELIMINARY
21
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN FUNCTIONS (Continued)
Port 3 (P37-P31). Port 3 is a 7-bit, CMOS compatible three
fixed input and four fixed output port. Port 3 consists of
three fixed input (P33-P31) and four fixed output (P37P34), and can be configured under software control for Input/Output, Interrupt, Port handshake, Data Memory functions and output from the counter/timers. P31, P32, and
P33 are standard CMOS inputs; outputs are push-pull.
Two on-board comparators process analog signals on P31
and P32 with reference to the voltage on Pref1 and P33.
The analog function is enabled by programming the Port 3
Mode Register (bit 1). P31 and P32 are programmable as
rising, falling, or both edge triggered interrupts (IRQ register bits 6 and 7). Pref1 and P33 are the comparator refer-
ence voltage inputs. Access to the Counter Timer edge detection circuit is through P31 or P20 (see CTR1
description). Other edge detect and IRQ modes are described in Tables (3-6). Handshake lines Ports 0, 1, and 2
are available on P31 through P36.
Port 3 provides the following control functions: handshake
for Ports 0, 1, and 2 (/DAV and RDY); three external interrupt request signals (IRQ2-IRQ0); Data Memory Select
(/DM) (Table 3).
Port 3 also provides output for each of the counter/timers
and the AND/OR Logic. Control is performed by programming bits D5-D4 of CTR1, bit 0 of CTR0 and bit 0 of CTR2.
Table 3. Pin Assignments
Pin
Pref1
P31
P32
P33
P34
P35
P36
P37
P20
I/O
IN
IN
IN
IN
OUT
OUT
OUT
OUT
I/O
C/T
IN
T8
T16
T8/16
Comp.
Int.
P0 HS
RF1
AN1
AN2
RF2
AO1
IRQ2
IRQ0
IRQ1
D/R
P1 HS
P2 HS
Ext
D/R
D/R
R/D
DM
R/D
R/D
AO2
IN
Notes:
D = /DAV
R = RDY
HS = Handshake Signals
Comparator Inputs. In Analog Mode, Port 3 (P31 and
P32) have a comparator front end. The comparator reference is supplied to P33 and Pref1. In this mode, the P33
internal data latch and its corresponding IRQ1 is diverted
to the SMR sources (excluding P31,P32, and P33) as
shown in figure 41. In digital mode, P33 is used as D3 of
the Port 3 input register which then generates IRQ1 as
shown in Figure 17.
When P31 is used for counter timer input (demodulation
mode), input is always taken from the P31 digital input
buffer whether or not analog mode is enabled).
Comparator Outputs. These may be programmed to be
outputted on P34 and P37 through the PCON register (Figures 16,38).
/RESET (Input, active Low). Initializes the MCU. Reset is
accomplished either through Power-On, Watch-Dog Timer, Stop-Mode Recovery, Low Voltage detection, or external reset. During Power-On Reset and Watch-Dog Timer
Reset, the internally generated reset drives the reset pin
Low for the POR time. Any devices driving the external reset line should be open-drain in order to avoid damage
from a possible conflict during reset conditions. Pull-up is
provided internally.
Notes: Comparators are powered down by entering STOP
mode. For P31-P33 to be used in a Stop-Mode Recovery
source, these inputs must be placed into digital mode.
22
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
P34
Counter/Timer
1
PAD
T8
P34 OUT
P34 OUT
P31
+
-
Comp1
CTR0
Pref1
D0
0 Normal Control
1 8-bit Timer output active
P37
PAD
P37 OUT
P32
+
-
Comp2
P33 (Pref2)
PCON
D0
0 = P34, P37 Standard Output *
1 = P34, P37 Comparator Output
*
Reset condition.
Figure 16. Port 3 Configuration
DS96LV00800
PRELIMINARY
23
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PIN FUNCTIONS (Continued)
After the POR time, /RESET is a Schmitt-triggered input.
To avoid asynchronous and noisy reset problems, the
Z86LXX is equipped with a reset filter of four external
clocks (4TpC). If the external reset signal is less than 4TpC
in duration, no reset occurs. On the fifth clock after the reset is detected, an internal RST signal is latched and held
for an internal register count of 18 external clocks, or for
the duration of the external reset, whichever is longer.
During the reset cycle, /DS is held active Low while /AS cycles at a rate of TpC/2. Program execution begins at location 000CH, 5-10 TpC cycles after the RST is released. For
Power-On Reset, the typical reset output time is 5 ms. The
Z86LXX does not reset WDTMR, SMR, P2M, or P3M registers on a Stop-Mode Recovery operation. The output
states of Port3 and Port2 are also un-affected by a StopMode recovery.
Pref1
200 KΩ
P31
P32
Z86L7X
MCU
P33
Mask
Option
Port 3
(I/O or Handshake)
P34
P35
Note:
P31, 32, 33 have a 200 KΩ
mask option
P36
P37
R247 = P3M
D1
1 = Analog
0 = Digital
DIG.
P31 (AN1)
+
Pref
IRQ2, P31 Data Latch
Comp1
AN.
-
P32 (AN2)
IRQ0, P32 Data Latch
Comp2
+
P33 (REF2)
-
IRQ1, P33 Data Latch
From Stop-Mode
Recovery Source of SMR
Figure 17. Port 3 Configuration
24
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR0, D0
Out 34
T8_Out
1
VDD
MUX
Pad
P34
CTR2, D0
VDD
Out 35
MUX
Pad
T16_Out
P35
CTR1, D6
VDD
Out 36
T8/16_Out
MUX
Pad
P36
Figure 18. Port 3 Counter Timer Output Configuration
DS96LV00800
PRELIMINARY
25
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
FUNCTIONAL DESCRIPTION
The Z86LXX family of IR CCP incorporates special functions to enhance the Z8's functionality in consumer and
battery operated applications.
65535
Program Memory. The Z86LXX family addresses
16/24/32 Kbytes of internal program memory. The first
twelve bytes are reserved for interrupt vectors. These locations contain the five 16-bit vectors which correspond to
the five available interrupts. In all cases, at addresses 32K
and greater, external program memory fetches will be executed (provided proper A/D port mode register settings).
Refer to external memory timing specifications. In Romless mode, program memory fetches begin at address
000Ch and data memory fetches begin at address 0000h.
External
Data
Memory
RAM. The Z86LXX devices all have 256 bytes of RAM
which make up the Register file.
32,768
External ROM
32768
Location of
First Byte of
Instruction
Executed
After RESET
On-Chip
ROM
Not Addressable
12
Reset Start Address
11
Reserved
10
Reserved
9
IRQ4
8
IRQ4
7
IRQ3
Figure 20. External Memory Map
6
IRQ3
5
IRQ2
4
IRQ2
3
IRQ1
2
IRQ1
External Memory (/DM). The Z86LXX addresses up to 32
Kbytes of external memory beginning at address 32768
(Figure 20). External data memory is included with, or separated from, the external program memory space. /DM, an
optional I/O function that is programmed to appear on P34,
is used to distinguish between data and program memory
space. The state of the /DM signal is controlled by the type
of instruction being executed. An LDC opcode references
PROGRAM (/DM inactive) memory, and an LDE instruction references data (/DM active Low) memory.
1
IRQ0
0
IRQ0
0
Interrupt
Vector
(Lower Byte)
Interrupt
Vector
(Upper Byte)
Figure 19. Program Memory Map(32K ROM)
26
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Expanded Register File. The register file has been expanded to allow for additional system control registers,
and for mapping of additional peripheral devices into the
register address area. The Z8 register address space R0
through R15 has been implemented as 16 banks of 16 registers per bank. These register groups are known as the
ERF (Expanded Register File). Bits 7-4 of register RP select the working register group. Bits 3-0 of register RP select the expanded register file bank. Note that expanded
register bank is also referred to as expanded register
group (Figure 21).
The upper nibble of the register pointer (Figure 23) selects
which working register group of 16 bytes in the register file,
out of the possible 256, will be accessed. The lower nibble
selects the expanded register file bank and, in the case of
the Z86LXX family, banks 0, F, and D are implemented. A
0h in the lower nibble will allow the normal register file
(bank 0) to be addressed, but any other value from 1h to
Fh will exchange the lower 16 registers to an expanded
register bank.
DS96LV00800
For example:
Z86L73: (See Figure 21)
1
R253 RP = 00h
R0 = Port 0
R1 = Port 1
R2 = Port 2
R3 = Port 3
But if:
R253 RP = 0Dh
R0 = CTRL0
R1 = CTRL1
R2 = CTRL2
R3 = Reserved
The counter/timers are mapped into ERF group D. Access
is easily done using the following example:
LD
RP, #0Dh Select ERF D for access to bank D ( working register group 0)
LD
R0,#xx
load CTRL0
LD
1, #xx
load CTRL1
LD
R1, 2
CTRL2 → CTRL1
LD
RP, #7Dh Select expanded register bank D and
working register group 7 of bank 0 for access .
LD
71h, 2
CTRL2 → register 71h
LD
R1, 2
CTRL2 → register 71h
PRELIMINARY
27
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Z8® STANDARD CONTROL REGISTERS
RESET CONDITION
D7 D6 D5 D4 D3 D2 D1 D0
REGISTER**
REGISTER POINTER
7
6
5
4
3
2
1
0
Expanded Register
Bank/Group Pointer
Working Register
Group Pointer
*
*
Z8 Register File (Bank0) **
FF
FO
FF
SPL
U
U
U
U
U
U
U
U
FE
SPH
U
U
U
U
U
U
U
U
FD
RP
0
0
0
0
0
0
0
0
FC
FLAGS
U
U
U
U
U
U
U
U
FB
IMR
0
U
U
U
U
U
U
U
FA
IRQ
0
0
0
0
0
0
0
0
F9
IPR
U
U
U
U
U
U
U
U
F8
P01M
0
1
0
0
1
1
0
1
F7
P3M
0
0
0
0
0
0
0
0
F6
P2M
1
1
1
1
1
1
1
1
F5
Reserved
U
U
U
U
U
U
U
U
F4
Reserved
U
U
U
U
U
U
U
U
F3
Reserved
U
U
U
U
U
U
U
U
F2
Reserved
U
U
U
U
U
U
U
U
F1
Reserved
0
0
0
0
0
0
0
0
F0
Reserved
0
U
U
0
0
0
0
0
EXPANDED REG. BANK/GROUP (F)
REGISTER**
RESET CONDITION
*
7F
Reserved
†
Reserved
0F
00
*
(F) 0F
WDTMR
(F) 0E
Reserved
(F) 0D
SMR2
(F) 0C
Reserved
(F) 0B
SMR
(F) 0A
Reserved
(F) 09
Reserved
(F) 08
Reserved
(F) 07
Reserved
(F) 06
Reserved
(F) 05
Reserved
(F) 04
Reserved
(F) 03
Reserved
(F) 02
Reserved
(F) 01
Reserved
(F) 00
PCON
U
U
U
0
1
1
0
1
U
0
U
0
0
0
U
U
0
0
1
0
0
0
U
0
U
U
U
U
U
U
U
0
EXPANDED REG. BANK/GROUP (D)
REGISTER**
EXPANDED REG. GROUP (0)
REGISTER**
*
*
RESET CONDITION
RESET CONDITION
(D) 0C
Reserved
(D) 0B
HI8
U
U
U
U
U
U
U
U
U
(D) 0A
L08
U
U
U
U
U
U
U
U
U
U
(D) 09
HI16
U
U
U
U
U
U
U
U
U
U
(D) 08
L016
U
U
U
U
U
U
U
U
U
U
(D) 07
TC16H
U
U
U
U
U
U
U
U
(D) 06
TC16L
U
U
U
U
U
U
U
U
(D) 05
TC8H
U
U
U
U
U
U
U
U
** All addresses are in Hexadecimal
(D) 04
TC8L
U
U
U
U
U
U
U
U
† Will not be reset with a Stop-Mode Recovery, except Bit 0.
(D) 03
Reserved
(0) 03
P3
0
0
0
0
U
U
U
(0) 02
P2
U
U
U
U
U
U
(0) 01
P1
U
U
U
U
U
U
(0) 00
P0
U
U
U
U
U
U
U = Unknown
* Will not be reset with a Stop-Mode Recovery
(D) 02
CTR2
0
U
U
U
U
U
U
0
(D) 01
CTR1
0
0
U
U
U
U
U
U
(D) 00
CTR0
0
U
U
U
U
U
U
0
Figure 21. Expanded Register File Architecture
28
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Note: When SPH is used as a general-purpose register
and Port 0 is in address mode, the contents of SPH will be
loaded into Port 0 whenever the internal stack is accessed.
R253 RP
D7 D6 D5
D4 D3 D2
D1 D0
Default Setting After Reset = 0000 0000
Expanded Register
File Pointer
Working Register
Pointer
r
7
r
6
r
5
r
4
r3 r 2 r1 r 0
R253
The upper nibble of the register file address
provided by the register pointer specifies
the active working-register group
Figure 22. Register Pointer Register
Register File. The register file (bank 0) consists of four I/O
port registers, 236 general-purpose registers, and 16 control and status registers (R0-R3, R4-R239, and R240R255, respectively), Plus two expanded registers groups
(Banks D and F). Instructions can access registers directly
or indirectly through an 8-bit address field. This allows a
short, 4-bit register address using the Register Pointer
(Figure 23). In the 4-bit mode, the register file is divided
into 16 working register groups, each occupying 16 continuous locations. The Register Pointer addresses the starting location of the active working register group.
7F
70
6F
60
5F
50
4F
40
3F
The lower nibble
of the register
file address
provided by the
instruction points
to the specified
register
Specified Working
Register Group
30
2F
Note: Working register group E0-EF can only be accessed through working registers and indirect addressing
modes.
20
1F
Register Group 1
R15 to R0
Register Group 0
R15 to R4 *
10
Stack. The Z86LXX external data memory or the internal
register file is used for the stack. An 8-bit Stack Pointer
(R255) is used for the internal stack that resides in the general-purpose registers (R4-R239). SPH is used as a general-purpose register only when using internal stacks.
0F
I/O Ports
00
R3 to R0 *
Figure 23. Register Pointer
COUNTER/TIMER REGISTER DESCRIPTION
Table 4. Expanded Register Group D
(D)%0C
(D)%0B
(D)%0A
(D)%09
(D)%08
(D)%07
(D)%06
(D)%05
(D)%04
(D)%03
(D)%02
(D)%01
(D)%00
Reserved
HI8
LO8
HI16
LO16
TC16H
TC16L
TC8H
TC8L
Reserved
CTR2
CTR1
CTR0
Register Description
HI8(D)%0B: Holds the captured data from the output of the
8-bit Counter/Timer0. This register is typically used to hold
the number of counts when the input signal is 1.
Field
Bit Position
T8_Capture_HI
76543210
Description
R
W
Captured Data
No Effect
L08(D)%0A: Holds the captured data from the output of
the 8-bit Counter/Timer0. This register is typically used to
hold the number of counts when the input signal is 0.
Field
Bit Position
T8_Capture_L0
76543210
Description
R
Captured Data
No Effect
W
DS96LV00800
PRELIMINARY
29
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
HI16(D)%09: Holds the captured data from the output of
the 16-bit Counter/Timer16. This register holds the MSByte of the data.
Field
Bit Position
T16_Capture_HI
76543210
Description
R
Captured Data
No Effect
W
TC16L(D)%06: Counter/Timer2 LS-Byte Hold Register.
Field
Bit Position
T16_Data_LO76543210
Description
R/W
Data
TC8H(D)%05: Counter/Timer8 High Hold Register.
Field
Bit Position
T8_Level_HI
76543210
Description
R/W
Data
L016(D)%08: Holds the captured data from the output of
the 16-bit Counter/Timer16. This register holds the LSByte of the data.
TC8L(D)%04: Counter/Timer8 Low Hold Register.
Field
Description
Field
Bit Position
Captured Data
No Effect
T8_Level_LO
76543210
Bit Position
T16_Capture_L 76543210
O
R
W
Description
R/W
Data
TC16H(D)%07: Counter/Timer2 MS-Byte Hold Register.
Field
Bit Position
T16_Data_HI 76543210
30
Description
R/W
Data
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR0 (D)00: Counter/Timer8 Control Register.
Field
T8_Enable
Bit Position
7-------
Value
R
W
Single/Modulo-N
-6-------
R/W
Time_Out
--5------
R
W
T8 _Clock
---43---
R/W
Capture_INT_MASK
-----2--
R/W
Counter_INT_Mask
------1-
R/W
P34_Out
-------0
R/W
0*
1
0
1
0
1
0
1
0
1
00
01
10
11
0
1
0
1
0*
1
Description
1
Counter Disabled
Counter Enabled
Stop Counter
Enable Counter
Modulo-N
Single Pass
No Counter Time-Out
Counter Time-Out Occurred
No Effect
Reset Flag to 0
SCLK
SCLK/2
SCLK/4
SCLK/8
Disable Data Capture Int.
Enable Data Capture Int.
Disable Time-Out Int.
Enable Time-Out Int.
P34 as Port Output
T8 Output on P34
Note: * Indicates the value upon Power-On Reset.
CTR0: Counter/Timer8 Control Register Description
T8 Clock. Defines the frequency of the input signal to T8.
T8 Enable. This field enables T8 when set (written) to 1.
Capture_INT_Mask. Set this bit to allow interrupt when
data is captured into either LO8 or HI8 upon a positive or
negative edge detection in demodulation mode.
Single/Modulo-N. When set to 0 (modulo-n), the counter
reloads the initial value when the terminal count is
reached. When set to 1 (single pass), the counter stops
when the terminal count is reached.
Time-Out. This bit is set when T8 times out (terminal count
reached). To reset this bit, a 1 should be written to this location. This is the only way to reset this status condition, therefore, care should be taken to reset this bit
prior to using/enabling the counter/timers.
Counter_INT_Mask. Set this bit to allow interrupt when T8
has a time out.
P34_Out. This bit defines whether P34 is used as a normal
output pin or the T8 output.
Note: Care must be taken when utilizing the OR or AND
commands to manipulate CTR0, bit 5 and CTR1, bits 0
and 1 (Demodulation Mode). These instructions use a
Read-Modify-Write sequence in which the current status
from the CTR0 and CTR1 registers will be ORed or ANDed
with the designated value and then written back into the
registers. Example: When the status of bit 5 is 1, a timer
reset condition will occur.
DS96LV00800
PRELIMINARY
31
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR1(D)%01: Controls the functions in common with the T8 and T16.
Field
Bit Position
Value
Mode
7-------
R/W
P36_Out/Demodulator
_Input
-6------
R/W
0*
0*
1
0
1
T8/T16_Logic/
Edge _Detect
--54----
R/W
00
01
10
11
00
01
10
11
Transmit_Submode/
Glitch_Filter
----32--
R/W
00
01
10
11
00
01
10
11
Initial_T8_Out/
Rising Edge
------1R/W
0
1
R
0
1
0
1
W
Initial_T16_Out/
Falling_Edge
-------0
R/W
0
1
R
0
1
0
1
W
Description
Transmit Mode
Demodulation Mode
Transmit Mode
Port Output
T8/T16 Output
Demodulation Mode
P31
P20
Transmit Mode
AND
OR
NOR
NAND
Demodulation Mode
Falling Edge
Rising Edge
Both Edges
Reserved
Transmit Mode
Normal Operation
Ping-Pong Mode
T16_Out = 0
T16_Out = 1
Demodulation Mode
No Filter
4 SCLK Cycle
8 SCLK Cycle
16 SCLK Cycle
Transmit Mode
T8_OUT is 0 Initially
T8_OUT is 1 Initially
Demodulation Mode
No Rising Edge
Rising Edge Detected
No Effect
Reset Flag to 0
Transmit Mode
T16_OUT is 0 Initially
T16_OUT is 1 Initially
Demodulation Mode
No Falling Edge
Falling Edge Detected
No Effect
Reset Flag to 0
Note: *Default upon Power-On Reset
32
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR1 Register Description
Mode. If it is 0, the Counter/Timers are in the transmit
mode, otherwise they are in the demodulation mode.
P36_Out/Demodulator_Input. In Transmit Mode, this bit
defines whether P36 is used as a normal output pin or the
combined output of T8 and T16.
In Demodulation Mode, this bit defines whether the input
signal to the Counter/Timers is from P20 or P31.
T8/T16_Logic/Edge _Detect. In Transmit Mode, this field
defines how the outputs of T8 and T16 are combined
(AND, OR, NOR, NAND).
In Demodulation Mode, this field defines which edge
should be detected by the edge detector.
Transmit_Submode/Glitch Filter. In Transmit Mode, this
field defines whether T8 and T16 are in the "Ping-Pong"
mode or in independent normal operation mode. Setting
this field to "Normal Operation Mode" terminates the "PingPong Mode" operation. When set to 10, T16 is immediately forced to a 0; a setting of 11 will force T16 to output a 1.
In Demodulation Mode, this field defines the width of the
glitch that should be filtered out.
DS96LV00800
Initial_T8_Out/Rising_Edge. In Transmit Mode, if 0, the
output of T8 is set to 0 when it starts to count. If 1, the output of T8 is set to 1 when it starts to count. When The
counter is not enabled and this bit is set to 1 or 0, T8_OUT
will be set to the opposite state of this bit. This insures that
when the clock is enabled a transition occurs to the initial
state set by CTR1, D1.
In Demodulation Mode, this bit is set to 1 when a rising
edge is detected in the input signal. In order to reset it, a 1
should be written to this location.
Initial_T16 Out/Falling _Edge. In Transmit Mode, if it is 0,
the output of T16 is set to 0 when it starts to count. If it is
1, the output of T16 is set to 1 when it starts to count. This
bit is effective only in Normal or Ping-Pong Mode (CTR1,
D3, D2). When the counter is not enabled and this bit is
set, T16_OUT will be set to the opposite state of this bit.
This insures that when the clock is enabled a transition occurs to the initial state set by CTR1, D0.
In Demodulation Mode, this bit is set to 1 when a falling
edge is detected in the input signal. In order to reset it, a 1
should be written to this location.
Note: Modifying CTR1, (D1 or D0) while the counters are
enabled will cause un-predictable output from T8/16_OUT.
PRELIMINARY
33
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR2 (D)%02: Counter/Timer16 Control Register.
Field
T16_Enable
Bit Position
Value
R
7-------
0*
1
0
1
W
Single/Modulo-N
R/W
-6------
0
1
Time_Out
0
1
0
1
0
1
00
01
10
11
0
1
0
R
--5-----
W
T16 _Clock
---43---
R/W
Capture_INT_Mask
-----2--
R/W
Counter_INT_Mask
------1-
R/W
P35_Out
-------0
R/W
0*
1
Description
Counter Disabled
Counter Enabled
Stop Counter
Enable Counter
Transmit Mode
Modulo-N
Single Pass
Demodulation Mode
T16 Recognizes Edge
T16 Does Not Recognize Edge
No Counter Time-Out
Counter Time-Out Occurred
No Effect
Reset Flag to 0
SCLK
SCLK/2
SCLK/4
SCLK/8
Disable Data Capture Int.
Enable Data Capture Int.
Disable Time-Out Int.
Enable Time-Out Int.
P35 as Port Output
T16 Output on P35
Note: * Indicates the value upon Power-On Reset.
CTR2 Description
T16_Clock. Defines the frequency of the input signal to
Counter/Timer16.
T16_Enable. This field enables T16 when set to 1.
Single/Modulo-N. In Transmit Mode, when set to 0, the
counter reloads the initial value when terminal count is
reached. When set to 1, the counter stops when the terminal count is reached.
In Demodulation Mode, when set to 0 , T16 captures and
reloads on detection of all the edges; when set to 1, T16
captures and detects on the first edge, but ignores the subsequent edges. For details, see the description of T16 Demodulation Mode.
Capture_INT_Mask. Set this bit to allow interrupt when
data is captured into LO16 and HI16.
Counter_INT_Mask. Set this bit to allow interrupt when
T16 times out.
P35_Out. This bit defines whether P35 is used as a normal
output pin or T16 output.
Time_Out. This bit is set when T16 times out (terminal
count reached). In order to reset it, a 1 should be written to
this location.
34
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
SMR2(F)%0D: Stop-Mode Recovery Register 2.
Field
Bit Position
Value
Reserved
Recovery Level
7-------6------
W
Reserved
Source
--5-------432--
W
Reserved
------10
0
0*
1
0
000*
001
010
011
100
101
110
111
00
Description
1
Reserved (Must be 0)
Low
High
Reserved (Must be 0)
A. POR Only
B. NAND of P23-P20
C. NAND or P27-P20
D. NOR of P33-P31
E. NAND of P33-P31
F. NOR of P33-P31, P00,P07
G. NAND of P33-P31,P00,P07
H. NAND of P33-P31,P22-P20
Reserved (Must be 0)
Notes:
* Indicates the value upon Power-On Reset
Port pins configured as outputs are ignored as a SMR recovery source.
DS96LV00800
PRELIMINARY
35
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Counter/Timer Functional Blocks
CTR1 D5,D4
P31
Glitch
Filter
MUX
P20
Edge
Detector
Pos Edge
Neg Edge
CTR1 D6
CTR1 D3,D2
Figure 24. Glitch Filter Circuitry
Z8 Data Bus
CTR0 D2
Pos Edge
IRQ4
Neg Edge
HI8
LO8
CTR0 D4, D3
SCLK
CTR0 D1
Clock
Select
Clock
TC8H
8-Bit
Counter T8
T8_OUT
TC8L
Z8 Data Bus
Figure 25. 8-Bit Counter/Timer Circuits
36
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Input Circuit
The edge detector monitors the input signal on P31 or P20.
Based on CTR1 D5-D4, a pulse is generated at the Pos
Edge or Neg Edge line when an edge is detected. Glitches
in the input signal which have a width less than specified
(CTR1 D3, D2) are filtered out.
T8 Transmit Mode
Before T8 is enabled, the output of T8 depends on CTR1,
D1. If it is 0, T8_OUT is 1. If it is 1, T8_OUT is 0.
When T8 is enabled, the output T8_OUT switches to the
initial value (CTR1 D1). If the initial value (CTR1 D1) is 0,
TC8L is loaded, otherwise TC8H is loaded into the
counter. In Single-Pass Mode (CTR0 D6), T8 counts down
to 0 and stops, T8_OUT toggles, the time-out status bit
(CTR0 D5) is set, and a time-out interrupt can be generated if it is enabled (CTR0 D1) (Figure 26). In Modulo-N
Mode, upon reaching terminal count, T8_OUT is toggled,
but no interrupt is generated. Then T8 loads a new count
(if the T8_OUT level now is 0), TC8L is loaded; if it is 1,
TC8H is loaded. T8 counts down to 0, toggles T8_OUT,
sets the time-out status bit (CTR0 D5) and generates an
interrupt if enabled (CTR0 D1) (Figure 27). This completes
one cycle. T8 then loads from TC8H or TC8L according to
the T8_OUT level, and repeats the cycle.
The user can modify the values in TC8H or TC8L at any
time. The new values take effect when they are loaded.
Care must be taken not to write these registers at the time
the values are to be loaded into the counter/timer, to ensure known operation. An initial count of 1 is not allowed (a non-function will occur). An initial count of 0
will cause TC8 to count from 0 to %FF to %FE (Note, % is
used for hexadecimal values). Transition from 0 to %FF is
not a time-out condition.
Note: Using the same instructions for stopping the
counter/timers and setting the status bits is not recommended. Two successive commands, first stopping
the counter/timers, then resetting the status bits is necessary. This is required because it takes one counter/timer
clock interval for the initiated event to actually occur.
TC8H Counts
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
T8_OUT Toggles,
Time-Out Interrupt
Figure 26. T8_OUT in Single-Pass Mode
T8_OUT Toggles
T8_OUT
TC8L
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
TC8H
TC8L
Time-Out Interrupt
TC8H
TC8L
Time-Out Interrupt
Figure 27. T8_OUT in Modulo-N Mode
DS96LV00800
PRELIMINARY
37
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
T8 Demodulation Mode
The user should program TC8L and TC8H to %FF. After
T8 is enabled, when the first edge (rising, falling, or both
depending on CTR1 D5, D4) is detected, it starts to count
down. When a subsequent edge (rising, falling, or both depending on CTR1 D5, D4) is detected during counting, the
current value of T8 is one's complemented and put into
one of the capture registers. If it is a positive edge, data is
put into LO8, if negative edge, HI8. One of the edge detect
status bits (CTR1 D1, D0) is set, and an interrupt can be
generated if enabled (CTR0 D2). Meanwhile, T8 is loaded
with %FF and starts counting again. Should T8 reach 0,
the time-out status bit (CTR0 D5) is set, an interrupt can be
generated if enabled (CTR0 D1), and T8 continues counting from %FF (Figure 28).
T8 (8-Bit)
Count Capture
No
T8_Enable
(Set By User)
Yes
Edge Present
No
Yes
What Kind Of Edge
Neg
Pos
T8 → HI8
T8 → L08
%FF → T8
Figure 28. Demodulation Mode Count Capture Flowchart
38
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
T8 (8-Bit)
Transmit Mode
No
1
T8_Enable Bit Set
CTR0, D7
Reset T8_Enable Bit
Yes
0
CTR1, D1
Value
Load TC8L
Reset T8_OUT
1
Load TC8H
Set T8_OUT
Set Time-out Status Bit
(CTR0 D5) and Generate
Timeout_Int If Enabled
Enable T8
No
T8_Timeout
Yes
Single Pass
Single Pass?
Modulo-N
1
0
T8_OUT Value
Load TC8L
Reset T8_OUT
Load TC8H
Set T8_OUT
Enable T8
Set Time-out Status Bit
(CTR0 D5) and Generate
Timeout_Int If Enabled
No
T8_Timeout
Yes
Disable T8
Figure 29. Transmit Mode Flowchart
DS96LV00800
PRELIMINARY
39
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
T8 (8-Bit)
Demodulation Mode
No
T8_Enable
CTR0, D7
Yes
%FF → TC8
No
First
Edge Present
Yes
Disable T8
Enable TC8
T8_Enable Bit Set
Yes
No
Edge Present
Yes
T8 Time Out
Set Edge Present Status
Bit And Trigger Data
Capture Int. If Enabled
No
Yes
Set Time-out Status
Bit And Trigger Time
Out Int. If Enabled
Continue Counting
Figure 30. Demodulation Mode Flowchart
40
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Z8 Data Bus
1
CTR2 D2
Pos Edge
IRQ3
Neg Edge
HI16
LO16
CTR2 D4, D3
SCLK
CTR2 D1
Clock
Select
Clock
16-Bit
Counter
T16
TC16H
T16_OUT
TC16L
Z8 Data Bus
Figure 31. 16-Bit Counter/Timer Circuits
T16 Transmit Mode
In Normal or Ping-Pong Mode, the output of T16 when not
enabled is dependent on CTR1, D0. If it is a 0, T16_OUT
is a 1; if it is a 1, T16_OUT is 0. The user can force the output of T16 to either a 0 or 1 whether it is enabled or not by
programming CTR1 D3, D2 to a 10 or 11.
When T16 is enabled, TC16H * 256 + TC16L is loaded,
and T16_OUT is switched to its initial value (CTR1 D0).
When T16 counts down to 0, T16_OUT is toggled (in Normal or Ping-Pong Mode), an interrupt is generated if enabled (CTR2 D1), and a status bit (CTR2 D5) is set. Note
that global interrupts will override this function as described in the interrupts section. If T16 is in Single-Pass
Mode, it is stopped at this point. If it is in Modulo-N Mode,
it is loaded with TC16H * 256 + TC16L and the counting
continues.
DS96LV00800
The user can modify the values in TC16H and TC16L at
any time. The new values take effect when they are loaded. Care must be taken not to load these registers at the
time the values are to be loaded into the counter/timer, to
ensure known operation. An initial count of 1 is not allowed. An initial count of 0 will cause T16 to count from 0
to %FF FF to %FFFE. Transition from 0 to %FFFF is not a
time-out condition.
PRELIMINARY
41
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
TC16H*256+TC16L Counts
“Counter Enable” Command,
T16_OUT Switches To Its
Initial Value (CTR1 D0)
T16_OUT Toggles,
Time-Out Interrupt
Figure 32. T16_OUT in Single-Pass Mode
TC16H*256+TC16L
TC16H*256+TC16L
T16_OUT
“Counter Enable” Command,
T16_OUT Switches To Its
Initial Value (CTR1 D0)
TC16H*256+TC16L
T16_OUT Toggles,
Time-Out Interrupt
T16_OUT Toggles,
Time-Out Interrupt
Figure 33. T16_OUT in Modulo-N Mode
T16 Demodulation Mode
The user should program TC16L and TC16H to %FF. After
T16 is enabled, when the first edge (rising, falling, or both
depending on CTR1 D5, D4) is detected, T16 captures
HI16 and LO16, reloads and begins counting.
If D6 of CTR2 is 0: When a subsequent edge (rising, falling, or both depending on CTR1 D5, D4) is detected during
counting, the current count in T16 is one's complemented
and put into HI16 and LO16. When data is captured, one
of the edge detect status bits (CTR1 D1, D0) is set and an
interrupt is generated if enabled (CTR2 D2). T16 is loaded
with %FFFF and starts again.
This T16 mode is generally used to measure space time;
the length of time between bursts of carrier signal(marks).
42
If D6 of CTR2 is 1: T16 ignores the subsequent edges in
the input signal and continues counting down. A time out
of T8 will cause T16 to capture its current value and generate an interrupt if enabled (CTR2, D2). In this case, T16
does not reload and continues counting. If D6 bit of CTR2
is toggled (by writing a 0 then a 1 to it), T16 will capture and
reload on the next edge (rising, falling, or both depending
on CTR1 D5, D4) but continue to ignore subsequent edges.
This T16 mode is generally used to measure mark times;
the length of an active carrier signal bursts.
Should T16 reach 0, it continues counting from %FFFF;
meanwhile, a status bit (CTR2 D5) is set and an interrupt
time-out can be generated if enabled (CTR2 D1).
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Ping-Pong Mode
This operation mode is only valid in Transmit Mode. T8
and T16 need to be programmed in Single-Pass Mode
(CTR0 D6, CTR2 D6) and Ping-Pong Mode needs to be
programmed in CTR1 D3, D2. The user can begin the operation by enabling either T8 or T16 (CTR0 D7 or CTR2
D7). For example, if T8 is enabled, T8_OUT is set to this
initial value (CTR1 D1). According to T8_OUT's level,
TC8H or TC8L is loaded into T8. After the terminal count
is reached, T8 is disabled and T16 is enabled. T16_OUT
switches to its initial value (CTR1 D0), data from TC16H
and TC16L is loaded, and T16 starts to count. After T16
reaches the terminal count it stops, T8 is enabled again,
and the whole cycle repeats. Interrupts can be allowed
when T8 or T16 reaches terminal control (CTR0 D1, CTR2
D1). To stop the Ping-Pong operation, write 00 to bits D3
and D2 of CTR1.
Note: Enabling Ping-Pong operation while the
counter/timers are running may cause intermittent
counter/timer function. Disable the counter/timers, then
reset the status flags prior to instituting this operation.
Enable
TC8
Time-Out
Enable
Ping-Pong
CTR1 D3,D2
TC16
Time-Out
Figure 34. Ping-Pong Mode
To Initiate Ping-Pong Mode
First, make sure both counter/timers are not running. Then
set T8 into Single-Pass Mode (CTR0 D6), set T16 into Single-Pass Mode (CTR2 D6), and set Ping-Pong Mode
(CTR1 D2, D3). These instructions do not have to be in
any particular order. Finally, start Ping-Pong Mode by enabling either T8 (CTR0 D7) or T16 (CTR2 D7).
DS96LV00800
During Ping-Pong Mode
The enable bits of T8 and T16 (CTR0 D7, CTR2 D7) will
be set and cleared alternately by hardware. The time-out
bits (CTR0 D5, CTR2 D5) will be set every time the
counter/timers reach the terminal count.
PRELIMINARY
43
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
P34_INTERNAL
MUX
P34_EXT
CTR0 D0
P36_INTERNAL
T8_OUT
T16_OUT
CTR1, D2
AND/OR/NOR/NAND
Logic
MUX
P36_EXT
MUX
CTR1 D6
CTR1 D5,D4
CTR1 D3
P35_INTERNAL
MUX
P35_EXT
CTR2 D0
Figure 35. Output Circuit
44
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Interrupts. The Z86LXX has five different interrupts. The
interrupts are maskable and prioritized (Figure 36). The
five sources are divided as follows: three sources are
claimed by Port 3 lines P33-P31, the remaining two by the
counter/timers (Table 5). The Interrupt Mask Register globally or individually enables or disables the five interrupt
requests.
IRQ0
IRQ2
IRQ 1, 3, 4
Interrupt
Edge
Select
IRQ Register (D6, D7)
IRQ
IMR
5
Global
Interrupt
Enable
Interrupt
Request
IPR
Priority
Logic
Vector Select
Figure 36. Interrupt Block Diagram
DS96LV00800
PRELIMINARY
45
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Table 5. Interrupt Types, Sources, and Vectors
Vector
Location
Name
Source
IRQ0
/DAV0,
IRQ0
0, 1
IRQ1,
IRQ1
2, 3
IRQ2
/DAV2,
IRQ2, TIN
4, 5
IRQ3
IRQ4
T16
T8
6, 7
8, 9
Comments
External
(P32), Rising
Falling Edge
Triggered
External
(P33), Falling
Edge Triggered
External
(P31), Rising
Falling Edge
Triggered
Internal
Internal
When more than one interrupt is pending, priorities are resolved by a programmable priority encoder controlled by
the Interrupt Priority register. An interrupt machine cycle is
activated when an interrupt request is granted. This disables all subsequent interrupts, saves the Program
Counter and Status Flags, and then branches to the program memory vector location reserved for that interrupt.
All Z86LXX interrupts are vectored through locations in the
program memory. This memory location and the next byte
contain the 16-bit address of the interrupt service routine
for that particular interrupt request. To accommodate
polled interrupt systems, interrupt inputs are masked and
the Interrupt Request register is polled to determine which
of the interrupt requests need service.
An interrupt resulting from AN1 is mapped into IRQ2, and
an interrupt from AN2 is mapped into IRQ0. Interrupts
IRQ2 and IRQ0 may be rising, falling, or both edge triggered, and are programmable by the user. The software
can poll to identify the state of the pin.
46
Programming bits for the Interrupt Edge Select are located
in the IRQ Register (R250), bits D7 and D6 . The configuration is shown in Table 6.
Table 6. IRQ Register
IRQ
Interrupt Edge
D7
D6
IRQ2(P31)
IRQ0 (P32)
0
0
1
1
0
1
0
1
F
F
R
R/F
F
R
F
R/F
Notes:
F = Falling Edge
R = Rising Edge
In analog mode, the Stop-Mode Recovery sources selected by
the SMR register are connected to the IRQ1 input. Any of the
Stop-Mode Recovery sources for SMR (except P31, P32, and
P33) can be used to generate IRQ1 (falling edge triggered).
Clock. The Z86LXX on-chip oscillator has a high-gain,
parallel-resonant amplifier for connection to a crystal, LC,
ceramic resonator, or any suitable external clock source
(XTAL1 = Input, XTAL2 = Output). The crystal should be
AT cut, 1 MHz to 8 MHz maximum, with a series resistance
(RS) less than or equal to 100 Ohms. The Z86LXX on-chip
oscillator may be driven with a low cost RC network or other suitable external clock source.
For 32 kHz crystal operation, an external feedback resistor
(Rf) and a serial resistor (Rd) are required. See Figure 37.
The crystal should be connected across XTAL1 and
XTAL2 using the recommended capacitors (capacitance
greater than or equal to 22 pF) from each pin to ground.
The RC oscillator configuration is an external resistor connected from XTAL1 to XTAL2, with a frequency-setting capacitor from XTAL1 to ground (Figure 37).
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Power-On Reset (POR). A timer circuit clocked by a dedicated on-board RC oscillator is used for the Power-On Reset (POR) timer function. The POR time allows VCC and
the oscillator circuit to stabilize before instruction execution begins.
The POR timer circuit is a one-shot timer triggered by one
of three conditions:
XTAL1
C1
3. WDT Time-Out.
The POR time is a nominal 5 ms. Bit 5 of the Stop-Mode
Register determines whether the POR timer is bypassed
after Stop-Mode Recovery (typical for external clock, RC,
LC oscillators).
XTAL1
C1
XTAL1
C1
XTAL1
Rf
R
L
XTAL2
1
2. Stop-Mode Recovery (if D5 of SMR = 1).
XTAL1
C1
C2
1. Power Fail to Power OK status including Waking up
from (VLV Standby).
XTAL2
XTAL2
XTAL2
XTAL2
C2
C2
Ceramic Resonator or Crystal
C1, C2 = 47 pF TYP *
f = 8 MHz
* Preliminary value including pin parasitics
LC
C1, C2 = 22 pF
RC
@ 3V VCC (TYP)
L = 130 µH *
f = 3 MHz *
C1 = 33 pF *
R = 1K *
Rd
32 kHz XTAL
C1 = 20 pF, C = 33
pF
Rd = 56 - 470K
Rf =10 M
External Clock
Figure 37. Oscillator Configuration
HALT. HALT turns off the internal CPU clock, but not the
XTAL oscillation. The counter/timers and external interrupts IRQ0, IRQ1, IRQ2, IRQ3, and IRQ4 remain active.
The devices are recovered by interrupts, either externally
or internally generated. An interrupt request must be executed (enabled) to exit HALT mode. After the interrupt service routine, the program continues from the instruction after the HALT.
DS96LV00800
STOP. This instruction turns off the internal clock and external crystal oscillation and reduces the standby current
to 10 µA or less. STOP mode is terminated only by a reset,
such as WDT time-out, POR, SMR, or external reset. This
causes the processor to restart the application program at
address 000CH. In order to enter STOP (or HALT) mode,
it is necessary to first flush the instruction pipeline to avoid
suspending execution in mid-instruction. To do this, the
user must execute a NOP (opcode = FFH) immediately before the appropriate sleep instruction, i.e.,
FF
6F
NOP
STOP
FF
7F
NOP
HALT
PRELIMINARY
; clear the pipeline
; enter STOP mode
or
; clear the pipeline
; enter HALT mode
47
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Port Configuration Register (PCON). The PCON register configures the comparator output on Port 3. It is located in the expanded register file at Bank F, location 00 (Figure 38).
SMR (F) 0B
D7 D6 D5 D4 D3 D2 D1 D0
SCLK/TCLK Divide-by-16
0 OFF **
1 ON
PCON (FH) 00H
D7 D6 D5
Reserved (Must be 0)
D4 D3 D2 D1 D0
Stop-Mode Recovery Source
000 POR Only *
001 Reserved
010 P31
0 11 P32
100 P33
101 P27
11 0 P2 NOR 0-3
111 P2 NOR 0-7
Comparator Output Port 3
0 P34, P37 Standard Output*
1 P34, P37 Comparator Output
Reserved (Must be 1)
* Default Setting After Reset
Stop Delay
0 OFF
1 ON *
Figure 38. Port Configuration Register (PCON)
(Write Only)
Comparator Output Port 3 (D0). Bit 0 controls the comparator
used in Port 3. A 1 in this location brings the comparator
outputs to P34 and P37, and a 0 releases the Port to its
standard I/O configuration.
Stop-Mode Recovery Register (SMR). This register selects the clock divide value and determines the mode of
Stop-Mode Recovery (Figure 39). All bits are write only except bit 7, which is read only. Bit 7 is a flag bit that is hardware set on the condition of STOP recovery and reset by
a power-on cycle. Bit 6 controls whether a low level or a
high level is required from the recovery source. Bit 5 controls the reset delay after recovery. Bits D2, D3, and D4, or
the SMR register, specify the source of the Stop-Mode Recovery signal. Bits D0 determines determines if
SCLK/TCLK are divided by 16 or not. The SMR is located
in Bank F of the Expanded Register Group at address
0BH.
Stop Recovery Level
0 Low *
1 High
Stop Flag
0 POR *
1 Stop Recovery
* Default Setting After Reset
** Default Setting After Reset and Stop-Mode Recovery
Figure 39. Stop-Mode Recovery Register
OSC
÷2
÷ 16
SCLK
SMR, D0
TCLK
Figure 40. SCLK Circuit
48
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
SMR D4 D3 D2
0 0 0
SMR2 D4 D3 D2
0 0 0
1
VCC
VCC
SMR D4 D3 D2
0 1 0
SMR2 D4 D3 D2
0 0 1
P20
P31
S1
P23
SMR D4 D3 D2
0 1 1
SMR2 D4 D3 D2
0 1 0
P20
P32
S2
P27
SMR D4 D3 D2
1 0 0
P33
S3
SMR2 D4 D3 D2
0 1 1
P31
P32
P33
To IRQ1
SMR2 D4 D3 D2
1 0 0
S4
SMR D4 D3 D2
1 0 1
P31
P32
P33
P27
SMR D4 D3 D2
1 1 0
P20
P23
SMR D4 D3 D2
1 1 1
P20
P27
P31
P32
P33
P00
P07
P31
P32
P33
P00
P07
SMR D6
P31
P32
P33
P20
P21
P22
To RESET and WDT
Circuitry (Active Low)
SMR2 D4 D3 D2
1 0 1
SMR2 D4 D3 D2
1 1 0
SMR2 D4 D3 D2
1 1 1
SMR2 D6
Figure 41. Stop-Mode Recovery Source
DS96LV00800
PRELIMINARY
49
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
SCLK/TCLK Divide-by-16 Select (D0). D0 of the SMR
controls a Divide-by-16 prescaler of SCLK/TCLK. The purpose of this control is to selectively reduce device power
consumption during normal processor execution (SCLK
control) and/or HALT mode (where TCLK sources interrupt
logic). After Stop-Mode Recovery, this bit is set to a 0.
Stop-Mode Recovery Source (D2, D3, and D4). These
three bits of the SMR specify the wake up source of the
STOP recovery (Figure 41 and Table 7).
Table 7. Stop-Mode Recovery Source
Operation
Description of Action
SMR:432
D4
D3
D2
0
0
0
0
0
0
1
1
1
0
1
1
0
0
1
1
0
1
0
1
0
1
1
1
Description of Action
POR and/or external reset
recovery
Reserved
P31 transition
P32 transition
P33 transition
P27 transition
Logical NOR of P20
through P23
Logical NOR of P20
through P27
Note: Any Port 2 bit defined as an output will drive the corresponding input to the default state to allow the remaining
inputs to control the AND/OR function. Refer to SMR2 register for other recover sources.
Stop-Mode Recovery Delay Select (D5). This bit, if low,
disables the 5 ms /RESET delay after Stop-Mode Recovery. The default configuration of this bit is one. If the "fast"
wake up is selected, the Stop-Mode Recovery source
needs to be kept active for at least 5TpC.
Stop-Mode Recovery Edge Select (D6). A 1 in this bit position indicates that a High level on any one of the recovery
sources wakes the Z86LXX from STOP mode. A 0 indicates Low level recovery. The default is 0 on POR (Figure
36).
Cold or Warm Start (D7). This bit is set by the device
upon entering STOP mode. It is a Read Only Flag bit. A 1
in D7 (warm) indicates that the device will awaken from a
SMR source or a WDT while in STOP mode. A 0 in this bit
(cold) indicates that the device will be reset by a POR,
WDT while not in STOP, or the device awakened from a
low voltage standby mode.
Stop-Mode Recovery Register 2 (SMR2). This register
determines the mode of Stop-Mode Recovery for SMR2
Figure 42).
If SMR2 is used in conjunction with SMR, either of the
specified events will cause a Stop-Mode Recovery.
Note: Port pins configured as outputs are ignored as a
SMR or SMR2 recovery source. For example, if the NAND
or P23-P20 is selected as the recovery source and P20 is
configured as an output then the remaining SMR pins
(P23-P21) form the NAND equation.
50
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
SMR2 (0F) DH
1
D7 D6 D5 D4 D3 D2 D1 D0
Reserved (Must be 0)
Reserved (Must be 0)
Stop-Mode Recovery Source 2
000 POR only*
001 NAND P20, P21, P22, P23
010 NAND P20, P21, P22, P23, P24, P25, P26, P27
011 NOR P31, P32, P33
100 NAND P31, P32, P33
101 NOR P31, P32, P33, P00, P07
110 NAND P31, P32, P33, P00, P07
111 NAND P31, P32, P33, P20, P21, P22
Reserved
(Must be 0)
Recovery Level
0 Low*
1 High
Reserved (Must be 0)
Note: If used in conjunction with SMR,
either of the two specified events will
cause a Stop-Mode Recovery.
*Default Setting After Reset
Figure 42. Stop-Mode Recovery Register 2
((0F) DH: D2-D4, D6 Write Only)
DS96LV00800
PRELIMINARY
51
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Watch-Dog Timer Mode Register (WDTMR). The WDT
is a retriggerable one-shot timer that resets the Z8 if it
reaches its terminal count. The WDT must initially be enabled by executing the WDT instruction and refreshed on
subsequent executions of the WDT instruction. The WDT
circuit is driven by an on-board RC oscillator or external
oscillator from the XTAL1 pin. The WDT instruction affects
the Zero (Z), Sign (S), and Overflow (V) flags.
The POR clock source is selected with bit 4 of the WDT
register. Bit 0 and 1 control a tap circuit that determines the
time-out period. Bit 2 determines whether the WDT is active during HALT and Bit 3 determines WDT activity during
STOP. Bits 5 through 7 are reserved (Figure 42). This register is accessible only during the first 61 processor cycles
(122 XTAL clocks) from the execution of the first instruction after Power-On-Reset, Watch-Dog Reset, or a StopMode Recovery (Figure 43). After this point, the register
cannot be modified by any means, intentional or otherwise. The WDTMR cannot be read and is located in Bank
F of the Expanded Register Group at address location
0FH. It is organized as follows:
WDTMR (0F) 0F
D7 D6 D5 D4 D3 D2 D1 D0
WDT TAP
00
01 *
10
11
INT RC OSC External Clock
5 ms
256 TpC
10 ms
512 TpC
20 ms
1024 TpC
80 ms
4096 TpC
WDT During HALT
0 OFF
1 ON *
WDT During STOP
0 OFF
1 ON *
XTAL1/INT RC Select for WDT
0 On-Board RC *
1 XTAL
Reserved (Must be 0)
* Default Setting After Reset
Figure 43. Watch-Dog Timer Mode Register
(Write Only)
52
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
WDT Time Select (D0, D1). Selects the WDT time period.
It is configured as shown in Table 8.
WDTMR During HALT (D2). This bit determines whether
or not the WDT is active during HALT mode. A 1 indicates
active during HALT. The default is 1.
Table 8. WDT Time Select
D1
D0
Time-Out of
Internal RC OSC
Time-Out of
XTAL Clock
0
0
1
1
0
1
0
1
5 ms min
10 ms min
20 ms min
80 ms min
256 TpC
512 TpC
1024 TpC
4096 TpC
WDTMR During STOP (D3). This bit determines whether
or not the WDT is active during STOP mode. Since the
XTAL clock is stopped during STOP mode, the on-board
RC has to be selected as the clock source to the
WDT/POR counter. A 1 indicates active during STOP. The
default is 1.
Clock Source for WDT (D4). This bit determines which
oscillator source is used to clock the internal POR and
WDT counter chain. If the bit is a 1, the internal RC oscillator is bypassed and the POR and WDT clock source is
driven from the external pin, XTAL1. The default configuration of this bit is 0, which selects the RC oscillator.
Notes:
TpC = XTAL clock cycle.
The default on reset is 10 ms.
/RESET
5 Clock
Filter
* /CLR 2
CLK
18 Clock RESET
Generator
RESET
Internal
RESET
Active
High
WDT TAP SELECT
CK Source
Select
(WDTMR)
XTAL
M
U
X
INTERNAL
RC
OSC.
VDD
VBO/VLV
2V REF.
+
-
POR
3
4
WDT1 2
CLK
WDT/POR Counter Chain
*CLR1
Low Operating
Voltage Det.
VCC
WDT
From Stop
Mode
Recovery
Source
12 ns Glitch Filter
Stop Delay
Select (SMR)
* /CLR1 and /CLR2 enable the WDT/POR and
18 Clock Reset timers upon a Low to High input translation.
Figure 44. Resets and WDT
DS96LV00800
PRELIMINARY
53
1
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Mask Selectable Options. There are seven Mask Selectable Options to choose from based on ROM code requirements. These are:
1.8
1.6
1.4
RAM Protect
On/Off
RC/Other
RC/XTAL
32 kHz XTAL
On/Off
Port 04-07 Pull-Ups
On/Off
Port 00-03 Pull-Ups
On/Off
Port 20-27 Pull-Ups
On/Of
Port 30-33 Pull-Ups
On/Of
Port 3 Mouse Mode 0.4 VDD On/Off
Trip
VLV
VLV
1.2
1
1.8
0.6
0.4
0.2
0
Low Voltage Detection/Standby. An on-chip Voltage
Comparator checks that the VCC is at the required level for
correct operation of the device. Reset is globally driven
when VCC falls below VLV (Vrf1). A small further drop in
VCC causes the XTAL1 and XTAL2 circuitry to stop the
crystal or resonator clock. Typical Low-Voltage power consumpion in this Low Voltage Standby mode (ILV) is about
45 µA (varying with the number of Mask selectable options
enabled). If the VCC is allowed to stay above Vram, the
RAM content is preserved. When the power level is returned to above VLV, the device will perform a POR and
function normally (Figure 45).
0
15
35
25
Temperature
45
55
Figure 45. Typical Z86LXX Low Voltage vs
Temperature at 8 MHZ
The minimum operating voltage varies with the temperature and operating frequency, while VLV varies with temperature only.
The Low Voltage trip voltage (VLV) is less than 2.1V under
the following conditions:
Maximum (VLV) Conditions:
TA = 0°C, +55°C Internal clock frequency equal to or less
than 4.0 MHz
Note: The internal clock frequency is one-half the external
clock frequency.
54
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
EXPANDED REGISTER FILE CONTROL REGISTERS (0D)
1
CTR0 (0D) 0H
D7 D6 D5 D4 D3 D2 D1 D0
0 P34 as Port Output*
1 Timer8 Output
0 Disable T8 Time Out Interrupt
1 Enable T8 Time Out Interrupt
0 Disable T8 Data Capture Interrupt
1 Enable T8 Data Capture Interrupt
00
01
10
11
R
R
W
W
SCLK on T8
SCLK/2 on T8
SCLK/4 on T8
SCLK/8 on T8
0 No T8 Counter Time Out
1 T8 Counter Time Out Occured
0 No Effect
1 Reset Flag to 0
0 Modulo-N
1 Single Pass
* Default Setting After Reset
R
R
W
W
0
1
0
1
T8 Disabled *
T8 Enabled
Stop T8
Enable T8
Figure 46. TC8 Control Register
((0D) OH: Read/Write Except Where Noted)
DS96LV00800
PRELIMINARY
55
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR1 (0D) 1H
D7
D6
D5
D4
D3
D2
D1
D0
Transmit Mode
R/W 0 T16_OUT is 0 Initially
1 T16_OUT is 1 Initially
Demodulation Mode
R
0 No Falling Edge Detection
R
1 Falling Edge Detection
W
W
0 No Effect
1 Reset Flag to 0
Transmit Mode
R/W 0 T8_OUT is 0 Initially
1 T8_OUT is 1 Initially
Demodulation Mode
0 No Rising Edge Detection
R
1 Rising Edge Detection
R
0 No Effect
W
1 Reset Flag to 0
W
Transmit Mode
0 0 Normal Operation
0 1 Ping-Pong Mode
1 0 T16_OUT = 0
1 1 T16_OUT = 1
Demodulation Mode
0 0 No Filter
0 1 4 SCLK Cycle Filter
1 0 8 SCLK Cycle Filter
1 1 16 SCLK Cycle Filter
Transmit Mode/T8/T16 Logic
0 0 AND
0 1 OR
1 0 NOR
1 1 NAND
Demodulation Mode
0 0 Falling Edge Detection
0 1 Rising Edge Detection
1 0 Both Edge Detection
1 1 Reserved
Transmit Mode
0 P36 as Port Output *
1 P36 as T8/T16_OUT
Demodulation Mode
0 P31 as Demodulator Input
1 P20 as Demodulator Input
Transmit/Demodulation Modes
0 Transmit Mode *
1 Demodulation Mode
*Default setting after Reset
Note: Care must be taken in differentiating
Transmit Mode from Demodulation Mode.
Depending on which of these two modes is
operating, the CTR1 bit will have different
functions.
56
Note: Changing from one mode to
another cannot be done without
disabling the counter/timers.
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
CTR2 (0D) 02H
1
D7 D6 D5 D4 D3 D2 D1 D0
0
1
0
1
P35 is Port Output*
P35 is TC16 Output
Disable T16 Time-Out Interrupt
Enable T16 Time-Out Interrupt
0 Disable T16 Data Capture Interrupt
1 Enable T16 Data Capture Interrupt
00
01
10
11
R
R
W
W
SCLK on T16
SCLK/2 on T16
SCLK/4 on T16
SCLK/8 on T16
0
1
0
1
No T16 Time Out
T16 Time Out Occurs
No Effect
Reset Flag to 0
Transmit Mode
0 Modulo-N for T16
1 Single Pass for T16
Demodulator Mode
0 T16 Recognizes Edge
1 T16 Does Not Recognize Edge
* Default Setting After Reset
R
R
W
W
0
1
0
1
T16 Disabled *
T16 Enabled
Stop T16
Enable T16
Figure 48. T16 Control Register
((0D) 2H: Read/Write Except Where Noted)
DS96LV00800
PRELIMINARY
57
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
EXPANDED REGISTER FILE CONTROL REGISTERS (0F)
SMR (0F) 0B
D7 D6 D5 D4 D3 D2 D1 D0
SCLK/TCLK Divide-by-16
0 OFF **
1 ON
Reserved (Must be 0)
Stop-Mode Recovery Source
000 POR Only *
001 Reserved
010 P31
0 11 P32
100 P33
101 P27
11 0 P2 NOR 0-3
111 P2 NOR 0-7
Stop Delay
0 OFF
1 ON *
Stop Recovery Level
0 Low *
1 High
Stop Flag
0 POR *
1 Stop Recovery * *
* Default Setting After Reset
** Default Setting After Reset and Stop-Mode Recovery
Figure 49. Stop-Mode Recovery Register
((0F) 0BH: D6-D0 = Write Only, D7 = Read Only)
58
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
SMR2 (0F) 0DH
1
D7 D6 D5 D4 D3 D2 D1 D0
Reserved (Must be 0)
Reserved (Must be 0)
Stop-Mode Recovery Source 2
000 POR only*
001 NAND P20, P21, P22, P23
010 NAND P20, P21, P22, P23, P24, P25, P26, P27
011 NOR P31, P32, P33
100 NAND P31, P32, P33
101 NOR P31, P32, P33, P00, P07
110 NAND P31, P32, P33, P00, P07
111 NAND P31, P32, P33, P20, P21, P22
Reserved
(Must be 0)
Recovery Level
0 Low*
1 High
Reserved (Must be 0)
Note: If used in conjunction with SMR,
either of the two specified events will
cause a Stop-Mode Recovery.
*Default Setting After Reset
Figure 50. Stop-Mode Recovery Register 2
((0F) 0DH: D2-D4, D6 Write Only)
DS96LV00800
PRELIMINARY
59
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
WDTMR (0F) 0F
D7 D6 D5 D4 D3 D2 D1 D0
WDT TAP
00
01 *
10
11
INT RC OSC External Clock
5 ms
256 TpC
10 ms
512 TpC
20 ms
1024 TpC
80 ms
4096 TpC
WDT During HALT
0 OFF
1 ON *
WDT During STOP
0 OFF
1 ON *
XTAL1/INT RC Select for WDT
0 On-Board RC *
1 XTAL
Reserved (Must be 0)
* Default Setting After Reset
Figure 51. Watch-Dog Timer Register
((0F) 0FH: Write Only)
PCON (FH) 00H
D7 D6 D5
D4 D3 D2 D1 D0
Comparator Output Port 3
0 P34, P37 Standard Output*
1 P34, P37 Comparator Output
Reserved (Must be 1)
* Default Setting After Reset
Figure 52. Port Configuration Register (PCON)
((0F) 0H: Write Only)
60
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Z8 STANDARD CONTROL REGISTER DIAGRAMS
1
R248 P01M
R246 P2M
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
P00-P03 Mode
00 Output
01 Input*
1X A11-A8
P27-P20 I/O Definition
0 Defines Bit as OUTPUT
1 Defines Bit as INPUT*
*Default Setting After Reset
Stack Selection
0 External
1 Internal*
P17-P10 Mode
00 Byte Output
01 Reserved
10 AD7-AD0
11 High-Impedance AD7AD0,
/AS, /DS, /R//W, A11-A8,
A15-A12, If Selected
Figure 53. Port 2 Mode Register
(F6H: Write Only)
R247 P3M
External Memory Timing
0 Normal*
1 Extended
D7 D6 D5 D4 D3 D2 D1 D0
P07-P04 Mode
00 Output
01 Input*
1X A15-A12
0 Port 2 Open Drain*
1 Port 2 Push-pull
0 = P31, P32 Digital Mode
1 = P31, P32 Analog Mode
0 P32 = Input
P35 = Output
1 P32 = /DAV0/RDY0
P35 = RDY0//DAV0
00
01
10
11
P33 = Input
P34 = Output
P33 = Input
P34 = /DM
P33 = /DAV1/RDY1
P34 = RDY1//DAV1
* Default Setting After Reset.
Note: Only P00 and P07 are Available on Z86L71.
Figure 55. Port 0 and 1 Mode Register
(F8H: Write Only)
D7 D6 D5 D4 D3 D2 D1 D0
0 P31 = Input (TIN)
P36 = Output (TOUT)
1 P31 = /DAV2/RDY2
P36 = RDY2//DAV2
Interrupt Group Priority
000 Reserved
001 C>A>B
010 A>B>C
011 A>C>B
100 B>C>A
101 C>B>A
110 B>A>C
111 Reserved
Reserved (Must be 0)
* Default Setting After Result
Figure 54. Port 3 Mode Register
(F7H: Write Only)
IRQ1,IRQ4,Priority
(Group C)
0 IRQ1>IRQ4
1 IRQ4>IRQ1
IRQ0,IRQ2
Priority (Group B)
0 IRQ2>IRQ0
1 IRQ0>IRQ2
IRQ3,IRQ5Priority
(Group A)
0 IRQ5>IRQ3
1 IRQ3>IRQ5
Reserved (Must be 0)
Figure 56. Interrupt Priority Registers
((0) F9H: Write Only)
DS96LV00800
PRELIMINARY
61
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
R253 RP
R250 IRQ
D7 D6
D5
D4
D3
D2
D1
D7 D6 D5 D4 D3 D2 D1 D0
D0
IRQ0 = P32 Input
IRQ1 = P33 Input
IRQ2 = P31 Input
IRQ3 = T16
IRQ4 = T8
Expanded Register Bank
Pointer
Default Setting After
Reset = 0000 0000
Inter Edge
P31 ↓ P32 ↓ = 00
P31 ↓ P32 ↑ = 01
P31 ↑ P32 ↓ = 10
P31 ↑↓ P32 ↑↓ = 11
Figure 57. Interrupt Request Register
((0) FAH: Read/Write)
Working Register
Pointer
Figure 60. Register Pointer
((0) FDH: Read/Write)
R254 SPH
D7 D6 D5 D4 D3 D2 D1 D0
Stack Pointer Upper
Byte (SP15-SP8)
R251 IMR
D7 D6 D5 D4 D3 D2 D1 D0
Figure 61. Stack Pointer High
((0) FEH: Read/Write)
1 Enables IRQ4-IRQ0
(D0 = IRQ0)
Reserved (Must be 0)
Reserved (Must be 0)
0 Master Interrupt Disable*
1 Master Interrupt Enable
* Default Setting After Reset
R255 SPL
D7 D6 D5 D4 D3 D2 D1 D0
Stack Pointer Lower
Byte (SP7-SP0)
Figure 58. Interrupt Mask Register
((0) FBH: Read/Write)
Figure 62. Stack Pointer Low
((0) FFH: Read/Write)
R252 Flags
D7 D6 D5 D4 D3 D2 D1 D0
User Flag F1
User Flag F2
Half Carry Flag
Decimal Adjust Flag
Overflow Tag
Sign Flag
Zero Flag
Carry Flag
Figure 59. Flag Register
((0) FCH: Read/Write)
62
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
PACKAGE INFORMATION
1
Figure 63. 28-Pin DIP Package Diagram
Figure 64. 28-Pin SOIC Package Diagram
DS96LV00800
PRELIMINARY
63
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
Figure 65. 40-Pin DIP Package Diagram
Figure 66. 44-Pin PLCC Package Diagram
64
PRELIMINARY
DS96LV00800
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
1
Figure 67. 44-Pin QFP Package Diagram
DS96LV00800
PRELIMINARY
65
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
ORDERING INFORMATION
Z86L88/81/86/87/89/73
Codes
8.0 MHz
28-Pin DIP
Z86L8808PSC
Z86L8108PSC
Z86L8608PSC
Package
28-Pin SIOC
Z86L8808SSC
Z86L8108SSC
Z86L8608SSC
40-Pin DIP
Z86L8708PSC
Z86L8908PSC
Z86L7308PSC
44-Pin PLCC
Z86L8708VSC
Z86L8908VSC
Z86L7308VSC
P = Plastic DIP
F = Plastic Quad Flat Pack
V = Plastic Chip Carrier
S = SOIC (Small Outline Integrated Circuit)
44-Pin QFP
Z86L8708FSC
Z86L8908FSC
Z86L7308FSC
For fast results, contact your local Zilog sales office for assistance in ordering the part desired.
Temperature
S = 0°C to +70°C
Speed
8 = 8.0 MHz
Environmental
C = Plastic Standard
Example:
Z 86LXX 08 P S C
is a Z86LXX, 8 MHz, DIP, 0°C to +70°C, Plastic Standard Flow
Environmental Flow
Temperature
Package
Speed
Product Number
Zilog Prefix
66
PRELIMINARY
DS96LV00800