Ultra subminiature Pushbutton Switch
A9PS
Ultra subminiature size.
■ Gold-plated clip contact ensure high reliability.
■ The sealed bottom prevents flux penetration.
■ Washable, equivalent to IP64 (IEC-60529).
■ A9PS is smaller than A9P.
Height: A9P 13.3mm, A9PS 10.5mm (30% smaller than A9P)
RoHS Compliant
Typical Applications
Security Control Boards
Electric Power Instrumentation
Program Controllers
Ordering Information
Terminal Shape
DIP Terminal
Right Angle Terminal
Vertical Mount Terminal
Switching Functions
SPST
OFF
(ON)
A9PS16-0011
Quantity per tray
Note:
DPST
SPST
A9PS26-0011
A9PS16-0012
100
DPST
SPST
A9PS26-0012
A9PS16-0013
25
DPST
A9PS26-0013
50
(ON) shows Momentary.
● Caps
Available wide range og colors.
Colors
Models
White
Black
Blue
Green
Yellow
Red
A9PS-011
A9PS-021
A9PS-041
A9PS-051
A9PS-061
A9PS-071
4 dia.
Dimension
2.4
Dimension with the cap.
3.8
2.4
4 dia.
1
A9PS
A9PS
Specifications
■
Ratings/Characteristics
Switching capacity
100 mA at 28 VAC/DC, 0.1 μA (minimum current) at 20 mVAC/DC
Ambient operating temperature
−20 °C to 80 °C 60% RH max. (with no icing or condensation)
Ambient operating humidity
45 to 85% RH (5 to 35 °C)
Insulation resistance
500 MΩ min. (Initial value)
Contact resistance
80 mΩ max. (Initial value)
Dielectric strength
500 VAC for 1min between terminals, between terminals and ground
Vibration resistance
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance
Malufunction: 500 m/s2 min.
Durability
Mechanical: 50,000 operations min.
Electrical: 50,000 operations min.
Operating forcse
4.9 N max.
Weight
0.3 g
Dimensions
Note:
●
All units are in millimeters unless otherwise indicated.
DIP Terminal Models
1.6
(5.6)
2.54
0.3
3.3
4.5
0.2
0.45
4 dia.
Stroke
0.3
●
(3)
(6)
(3)
(4)
(1)
(4)
(1)
1
1
Note:
(6)
5.08 7
2 dia.
Single Pole Type
Marking Side
Double Pole Type
NO.(4) and (6) terminals in the SPDT models are dummys to support the Switch case.
Right Angle Terminal Models
1.6
5
(5.6)
3.3
4.5
0.2 0.45
4 dia.
0.3
1
(6)
(3)
(1)
(4)
(1)
Stroke
Single Pole Type
1
Marking Side
0.3
2.6 3.1
5.08
2
(3)
5.08 7
2 dia.
2.54
Double Pole Type
A9PS
●
A9PS
Vertical Mount Terminal Models
(5.6)
1.6
3.3
5.5
4.5
2.54
1
2 dia.
0.3
Stroke
(3)
(6)
(3)
(1)
(4)
(1)
7
2.6 3.6
1
Marking Side
1
2.54
●
0.3
0.45
4 dia.
5.08
Single Pole Type
5.08
Double Pole Type
PCB Dimensions (Top View)
DIP Terminal Models
Right Angle Terminal Models
2.54
Four-0.6 +0.1
0 dia.
5.08
Four-0.6 +0.1
0 dia.
(3)
(4)
(1)
5.08
Six-0.6 +0.1
0 dia.
(3)
(6)
5.08
5.08
2.54
(1)
(6)
5.08
(1)
(4)
(3)
Single Pole Type
Double Pole Type
Vertical Mount Terminal Models
2.54
2.54
5.08
5.08
(1)
(4)
(1)
(6)
(3)
5.08
5.08
(3)
Six-0.6 +0.1
0 dia.
Four-0.6 +0.1
0 dia.
Single Pole Type
Double Pole Type
Switching Function / Internal Connections
Switching Functions
(3)
(3)
OFF
(ON)
1
1
(3)
DPST Models
4
Note:
1
1
SPST Models
(6)
4
(3)
(6)
(ON) shows Momentary.
3
A9PS
A9PS
Safety Precautions
● Cautions
Use the switch within the rated voltage and current ranges,
otherwise the Switch may have a shortened life expectancy,
radiate heat,or burn out. This particularly applies to the
instantaneous voltages and currents when switching.
● Using Flux
Making mistakes in the type of flux or in the amount or method in
which it is applied can cause flux to enter the interior of the
Switch, with adverse effects on Switch performance. Assess the
proper flux, conditions,and methods prior to using it.
● Hardling
Do not apply excessive operating force to the Switch. Otherwise
the Switch may be damaged or deformed, and the switch
mechanism may malfunction as a result. Apply an operating force
not exceeding 9.8N {1,000gf}. Apply the operating load from the
top of the actuator. Do not apply a load from angle or from side
the actuator. Doing so may deform the Switch contact.
● RoHS Compliant
The "RoHS Compliant" designation indicates that the listed
models do not contain the six hazardous substances covered by
the RoHS Directive.
Reference: The following standards are used to determine
compliance for the six substances.
• Lead:
1,000 ppm max.
• Mercury:
1,000 ppm max.
• Cadmium:
100 ppm max.
• Hexavalent chromium: 1,000 ppm max.
• PBB:
1,000 ppm max.
• PBDF:
1,000 ppm max.
● Soldering
Observe the following conditions when soldering the Switch.
Automatic Soldering Bath
Soldering temperature: 260 °C max. (Preheating: 100 °C 120s max.)
Soldering time: 5s max.
Manual Soldering
Soldering temperature: 350 °C at the tip of the soldering iron.
Soldering time: 3s max.
● Washing
Apply alcohol based solvents to clean.
Do not clean the Switch immediately after soldering. Wait for at
least five minutes after soldering before cleaning.
Ultrasonic cleaning is not available dip into Switch washing
agents for two minutes maximum.
● Environment for Storage and Use
To prevent discoloration of the terminals and other problems
during storage, do not store the Switch in locations subject to the
following conditions.
1. High temperature or humidity
2. Corrosive gases
3. Direct sunlight
Also, the Switch is not waterproof or splash-resistance.
Do not use the Switch in locations that are subject to contact with
water. Do not subject the Switch to freezing or condensation.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. A198-E1-02
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
OMRON SWITCH & DEVICES Corporation
Consumer & Commercial Switch Department
Marketing
2075, Miyoshi, Nakaku, Okayama
Okayama, 703-8502 Japan
Tel: (81)86-277-6024/Fax: (81)86-276-5044
URL : http://www.omron.com/ecb/
Printed in Japan
0911 (0711) (W)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
A9PS16-0011 A9PS16-0012 A9PS16-0013 A9PS26-0011 A9PS26-0012 A9PS26-0013