CEL CE3521M4 20 ghz low noise fet in dual mold plastic pkg Datasheet

RF Low Noise FET
CE3521M4
20 GHz Low
Noise
FET
in Dual Mold
Plastic
Enter
a Short
Document/Title
Name
Here PKG
DESCRIPTION


PACKAGE
Low Noise and High Gain
Original Dual Mold Plastic package

Flat-lead 4-pin thin-type super minimold package
FEATURES

Low noise figure and high associated gain:
NF = 0.70 dB TYP., Ga = 11.9 dB TYP.
@VDS = 2 V, ID = 10 mA, f = 20 GHz
APPLICATIONS


DBS LNB gain-stage, Mix-stage
Low noise amplifier for microwave
communication systems
ORDERING INFORMATION
Part Number
CE3521M4
Order Number
CE3521M4-C2
This document is subject to change without notice.
Date Published: July 2016
CDS-0020-04 (Issue A)
Package
Flat-lead 4-pin
thin-type super
minimold
package
1
Marking
C04
Description
• Embossed tape 8 mm wide
• Pin 1 (source), Pin 2 (drain)
face the perforation side of
the tape
• MOQ 15 kpcs/reel
CE3521M4
PIN CONFIGURATION AND
INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
Source
2
Drain
3
Source
4
Gate
ABSOLUTE MAXIMUM RATINGS
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
Rating
Unit
Drain to Source Voltage
VDS
4.0
V
Gate to Source Voltage
VGS
-3.0
V
Drain Current
ID
IDSS
mA
Gate Current
IG
80
µA
Total Power Dissipation
Ptot
125
mW
Channel Temperature
Tch
+150
°C
Storage Temperature
Tstg
-55 to +125
Operation Temperature
Top
-55 to +125
°C
Note
°C
Note Refer to Total Power Dissipation vs. Ambient Temperature graph on page 4
RECOMMENDED OPERATING RANGE
(TA = +25˚C, unless otherwise specified)
Parameter
Drain to Source Voltage
Drain Current
This document is subject to change without notice.
Symbol
MIN.
TYP.
MAX.
Unit
VDS
+1
+2
+3
V
ID
5
10
15
mA
2
CE3521M4
ELECTRICAL CHARACTERISTICS
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
Condition
Gate to Source Leak Current
IGSO
VGS = -3.0V
Saturated Drain Current
IDSS
VDS = 2V, VGS = 0V
Gate to Source Cut-off Voltage
MIN.
TYP.
MAX.
Unit
-
0.4
10
µA
23
40
57
mA
VGS(off)
VDS = 2V, ID = 100µA
-1.10
-0.75
-0.39
V
Transconductance
Gm
VDS = 2V, ID = 10mA
47
62
-
mS
Noise Figure
NF
-
0.70
1.05
dB
Associated Gain
Ga
VDS = 2V, ID = 10mA,
f = 20GHz
9.9
11.9
-
dB
This document is subject to change without notice.
3
CE3521M4
TYPICAL CHARACTERISTICS:
(TA=+25℃, unless otherwise specified)
TOTAL POWER DISSIPATION
vs. AMBIENT TEMPERATURE
DRAIN CURRENT vs.
DRAIN TO SOURCE VOLTAGE
DRAIN CURRENT vs.
GATE TO SOURCE VOLTAGE
This document is subject to change without notice.
MINIMUM NOISE FIGURE &
ASSOCIATED GAIN vs. DRAIN CURRENT
4
CE3521M4
S-PARAMETERS
S-Parameters are available on the CEL web site.
RECOMMENDED SOLDERING CONDITIONS
Recommended Soldering Conditions are provided on the CEL web site.
PACKAGE DIMENSIONS
Flat-lead 4-pin thin-type super minimold package
This document is subject to change without notice.
5
CE3521M4
REVISION HISTORY
Version
CDS-0020-03 (Issue A)
February 19, 2016
CDS-0020-03 (Issue B)
April 27, 2016
CDS-0020-04 (Issue A)
July 29, 2016
Change to current version
Initial datasheet
Page(s)
N/A
Updated Marking Information
1, 2, 3
Updated Specs in “Absolute Maximum Ratings” Table
Added “Typical Characteristics” section (graphs)
Added “S-Parameters” and “Recommended Soldering
Conditions” sections
2, 4, 5
This document is subject to change without notice.
6
CE3521M4
[CAUTION]
・ All information included in this document is current as of the date this document is issued. Such information,
however, is subject to change without any prior notice.
・ You should not alter, modify, copy, or otherwise misappropriate any CEL product, whether in whole or in part.
・ CEL does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of
third parties by or arising from the use of CEL products or technical information described in this document. No
license, expressed, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual
property rights of CEL or others.
・ Descriptions of circuits, software and other related information in this document are provided only to illustrate the
operation of semiconductor products and application examples. You are fully responsible for the incorporation of
these circuits, software, and information in the design of your equipment. CEL assumes no responsibility for any
losses incurred by you or third parties arising from the use of these circuits, software, or information.
・ CEL has used reasonable care in preparing the information included in this document, but CEL does not warrant
that such information is error free. CEL assumes no liability whatsoever for any damages incurred by you resulting
from errors in or omissions from the information included herein.
・ Although CEL endeavors to improve the quality and reliability of its products, semiconductor products have specific
characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions.
Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or
damage caused by fire in the event of the failure of a CEL product, such as safety design for hardware and software
including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging
degradation or any other appropriate measures
Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final
products or system manufactured by you.
・ Please use CEL products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive.
CEL assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and
regulations.
・ This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent
of CEL.
・ Please contact CEL if you have any questions regarding the information contained in this document or CEL
products, or if you have any other inquiries.
This document is subject to change without notice.
7
CE3521M4
[CAUTION]
This product uses gallium arsenide (GaAs) of the toxic substance appointed in laws and ordinances.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
・ Do not dispose in fire or break up this product.
・ Do not chemically make gas or powder with this product.
・ When discarding this product, please obey the laws of your country.
・ Do not lick the product or in any way allow it to enter the mouth.
[CAUTION]
Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can
damage this device. This device must be protected at all times from ESD. Static charges may easily
produce potentials of several kilovolts on the human body or equipment, which can discharge
without detection. Industry-standard ESD precautions should be used at all times.
CEL Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054 • Tel: (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus
For inquiries email us at [email protected]
This document is subject to change without notice.
8
Similar pages