Sensortechnics BTEL5000D4C Precision very low differential pressure transmitter Datasheet

BTEL5000 / PTUL5000 Series
Precision very low differential pressure transmitters
FEATURES
· 1 to 10 mbar, 1 to 10 inH2O differential
pressure
· 1...6 V or 4...20 mA output
· Precision temperature compensated
and calibrated
· Rugged aluminium housing
· Female 1/8" BSP and 1/8" NPT fittings
MEDIA COMPATIBILITY
Pressure inlet:
Non-corrosive, non-ionic working fluids such as air, dry
gases and the like
Housing:
Aluminium, protection class IP 67 (according to
DIN EN 60529, NEMA 6)1
SPECIFICATIONS12
ELECTRICAL CONNECTION
Maximum ratings
1...6 V output version
Supply voltage11
Output current
BTEL/PTUL5...D1...
Source
Sink
BTEL/PTUL5...D4...
Temperature limits
Storage
Operating
Compensated
Proof pressure2
BTEL/PTUL5...01D...
BTEL/PTUL5...02D...
all others
Pressure at any port3
BTEL/PTUL5...01D...
BTEL/PTUL5...02D...
all others
12...32 V
1
12 to 32 V
+Vs
20 mA
10 mA
30 mA
sensor
2
Vout
4
GND
V
-Vs
3
-40...100°C
-25...85°C
0...50°C
case
4...20 mA output version
250 mbar / 100 "H2O
250 mbar / 100 "H2O
350 mbar / 150 "H2O
500 mbar / 200 "H2O
500 mbar / 200 "H2O
750 mbar / 300 "H2O
1
12 to 32 V
+Vs
sensor
V
4
-Vs
RL
GND
3
case
E / 11094 / A
1/5
www.first-sensor.com
www.sensortechnics.com
BTEL5000 / PTUL5000 Series
Precision very low differential pressure transmitters
COMMON PERFORMANCE CHARACTERISTICS9
Characteristics
Min.
Typ.
Position sensitivity
Max.
0.5
4
±0.1
Output noise (0 < f < 1 kHz)
0.04
Non-linearity and hysteresis
5
Long term stability
6
Thermal effects (0 to 50°C)
Offset
%FSO/g
±0.25
%FSO
BTEL/PTUL5...01D...
±0.5
all others
±0.2
BTEL5...01D...
BTEL5...02D.../
PTUL5...01D...
all others
±0.08
±0.16
±0.04
±0.10
±0.02
±0.06
±0.04
±0.08
Span
Response time (10 to 90 %)
Unit
1
%FSO/°C
ms
INDIVIDUAL PERFORMANCE CHARACTERISTICS9
1...6 V output versions (VS = 15 V, tamb = 25°C, RL > 100 kΩ, com. mode pressure = 0)
Characteristics
7
Zero pressure offset
Full scale span8
BTEL/PTUL50...D1...
BTEL/PTUL5P...D1...
BTEL/PTUL50...D1...
BTEL/PTUL5P...D1...
Min.
Typ.
Max.
0.9
3.4
4.9
2.4
1.0
3.5
5.0
2.5
6.0
1.1
3.6
5.1
2.6
Full scale output
Output impedance
Power supply rejection
50
Offset
Span
Power consumption
Unit
V
Ω
0.05
0.03
%FSO/V
60
mW
4...20 mA output versions (VS = 15 V, tamb = 25°C, RL = 100 Ω, com. mode pressure = 0)
Characteristics
Zero pressure offset7
Full scale span8
BTEL/PTUL50...D4...
BTEL/PTUL5P...D4...
BTEL/PTUL50...D4...
BTEL/PTUL5P...D4...
Full scale output
Min.
Typ.
Max.
3.9
11.9
15.9
7.9
4.0
12.0
16.0
8.0
20.0
4.1
12.1
16.1
8.1
Output impedance
Power supply rejection
Power consumption (IL = 20 mA)
E / 11094 / A
0.1
Offset
Span
Unit
mA
Ω
0.05
0.03
%FSO/V
260
mW
2/5
www.first-sensor.com
www.sensortechnics.com
BTEL5000 / PTUL5000 Series
Precision very low differential pressure transmitters
LOAD LIMITATION
4...20 mA output version
1200
Ohm
1000
800
600
operating
range
400
200
0
10
20
30 V
Vsupply
ELECTROMAGNETIC CAPABILITY10
Test conditions
Radiated, radio frequency
EN61000-4-3: 10 V/m, 80 to 1000 MHz
electromagnetic field immunity (RFI)
80 % AMC (1 kHz)
Electrical fast transient /
EN61000-4-4: ±2 kV
burst immunity (EFT)
Electrostatic discharge immunity
EN61000-4-2: ±4 kV, contact discharge
test (ESD)
±8 kV, air discharge
Immunity to conducted disturbances EN61000-4-6: 0.15 to 80 MHz
induced by radio-frequency fields
10 V, 80 % AMC (1 kHz)
Criterion Interference
A
<1 %FSO
B
<1 %FSO
B
<1 %FSO
A
<1 %FSO
Specification notes:
1.´ IP 67 protection for BTEL/PTUL5...A is given with locked connector only.
2. Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element.
3. This is the highest pressure which can be applied to any port at any time. At the same time the differential pressure between
the ports H and L must not exceed the maximum proof pressure.
4. Non-linearity refers to the Best Straight Line fit measured for offset, full scale span and 1/2 full scale span.
5. Long term stability is the change in output after one year or 1 million pressure cycles.
6. Thermal effects tested and guaranteed from 0...50 °C relative to 25°. All specifications shown are relative to 25°C.
7. Calibrated after minimum 3 minutes warm-up time.
8. Full scale span is the algebraic difference between the positive full scale output and zero pressure offset.
9. Higher pressure applied to port H.
10. Test are in accordance with EN 61000-6-2.
11. The minimum supply voltage is directly proportional to the load resistance seen by the transmitter. For more details see the
load limitation diagram.
12. CE-labelling is in accordance with 2004/108/EC.
E / 11094 / A
3/5
www.first-sensor.com
www.sensortechnics.com
BTEL5000 / PTUL5000 Series
Precision very low differential pressure transmitters
OUTLINE DRAWING
Connector version
40.0
(1.58)
NOM 86.0 (3.39)
20.0
(0.79)
13.5 diam. (0.53)
72.0 (2.84)
H: high pressure port
L: low pressure port
mating plug
8.0 (0.31) min.
4
M12 x 1
(0.47)
8.0 (0.31) min.
2 x M5
(UNC 10-24)
9.0
(0.35)
BTE.../PTE...: 2 x 1/8" BSP
PTU...: 2 x 1/8" NPT
mass: typ. 170 g
dimensions in mm (inches)
1
3
2
ELECTRICAL CONNECTION
Connection
1...6 V
4...20 mA
Pin
output
output
1
+Vs
+Vs
2
Vout
NC
3
case
case
4
-Vs
-Vs
Cable version
40.0
(1.58)
90.0 (3.54)
72.0 (2.84)
20.0
(0.79)
H: high pressure port
L: low pressure port
13.5 diam. (0.53)
8.0 (0.31) min.
1 m (3.3 ft) shielded cable
4 x 0.25 mm² (AWG24)
8.0 (0.31) min.
2 x M5
(UNC 10-24)
mass: typ. 220 g
dimensions in mm (inches)
E / 11094 / A
9.0
(0.35)
BTE.../PTE...: 2 x 1/8" BSP
PTU...: 2 x 1/8" NPT
ELECTRICAL CONNECTION
Connection
1...6 V
4...20 mA
output
output
bare
case/shield case/shield
brown
+Vs
+Vs
NC
white
NC
green
Vout
NC
yellow
-Vs
-Vs
4/5
www.first-sensor.com
www.sensortechnics.com
BTEL5000 / PTUL5000 Series
Precision very low differential pressure transmitters
RECOMMENDED CABLE/CONNECTOR ACCESSORY
for connector version
Order number ZK000101, other cable lengths on special request
NOM 2 m
PIN CONNECTION
36.5
Pin
1
2
3
4
NOM
60
Flying lead end
brown
green
white + shield
yellow
Included in delivery!
M12 x 1
Ø 20
dimensions in mm
ORDERING INFORMATION
BTEL/PTUL
5xxx
Calibration
BTEL: calibration in mbar
PTUL: calibration in inH2O
Pressure range
BTEL5000 series
001:
0...1 mbar
P01:
-1...+1 mbar
002:
0...2 mbar
P02:
-2...+2 mbar
005:
0...5 mbar
P05:
-5...+5 mbar
010:
0...10 mbar
P10: -10...+10 mbar
D
x
x
Electrical connection
A: connector version
C: cable version
PTUL5000 series
001:
0...1 inH2O
P01:
-1...+1 inH2O
002:
0...2 inH2O
P02:
-2...+2 inH2O
005:
0...5 inH2O
P05:
-5...+5 inH2O
010:
0...10 inH2O
P10: -10...+10 inH2O
Output signal
1: 1...6 V
4: 4...20 mA
Differential pressure
Note: 0...1 mbar devices not available with 1...6 V output signal
Other pressure ranges and options are widely available. Please contact First Sensor.
First Sensor reserves the right to make changes to any products herein. First Sensor does not assume any liability arising out of the application
or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
E / 11094 / A
5/5
www.first-sensor.com
www.sensortechnics.com
Similar pages