ALSC AS4C4M16S-6TCN Fully synchronous operation Datasheet

AS4C4M16S
Revision History AS4C4M16S- 54PIN 400 MIL PLASTIC TSOP II PACKAGE
Revision
Rev 1.0
Rev 2.0
Details
Preliminary datasheet
Removed 6TAN –– automotive temp
page 1 and page 52
(see separate datasheet for this option)
Added 6TCN – 166MHz clock – commercial temp
page 1 and page 52
Added in temperature range to page 1
* Operating temperature range
- Commercial (0 ~ 70°C) - Industrial (-40 ~ 85°C)
Date
February 2011
May 2014
May 2014
May 2014
Alliance Memory Inc. 551 Taylor Way, San Carlos, CA 94070
TEL: (650) 610-6800 FAX: (650) 620-9211
Alliance Memory Inc. reserves the right to change products or specification without notice.
AS4C4M16S
FEBRUARY 2011
64Mb / 4M x 16 bit Synchronous DRAM (SDRAM)
Rev2.0 May 2014
Alliance Memory
Table1. Key Specifications
Features
•
•
•
•
•
•
•
•
•
•
•
•
AS4C4M16S
Fast access time from clock: 5.4/5.4 ns
Fast clock rate: 166/143 MHz
Fully synchronous operation
Internal pipelined architecture
1M word x 16-bit x 4-bank
Programmable Mode registers
- CAS Latency: 2, or 3
- Burst Length: 1, 2, 4, 8, or full page
- Burst Type: interleaved or linear burst
- Burst stop function
Auto Refresh and Self Refresh
4096 refresh cycles/64ms
CKE power down mode
Single +3.3V ± 0.3V power supply
Interface: LVTTL
54-pin 400 mil plastic TSOP II package
- Pb free and Halogen free
- 6/7
tCK3 Clock Cycle time(min.)
tAC3 Access time from CLK(max.)
5.4/5.4ns
tRAS Row Active time(min.)
42/49 ns
tRC Row Cycle time(min.)
60/63 ns
6/7ns
Table 2. Ordering Information
Part Number
Frequency
Package
AS4C4M16S-6TCN
AS4C4M16S-6TIN
166MHz
166MHz
TSOP II
TSOP II
AS4C4M16S-7TCN
143MHz
TSOP II
T: indicates TSOPII Package,
N: indicates Pb and Halogen Free for TSOPII Package
Figure 1.Pin Assignment (Top View)
Overview
The AS4C4M16S SDRAM is a high-speed CMOS
synchronous DRAM containing 64 Mbits. It is
internally configured as 4 Banks of 1M word x 16
DRAM with a synchronous interface (all signals are
registered on the positive edge of the clock signal,
CLK). Read and write accesses to the SDRAM are
burst oriented; accesses st art at a selected location
and continue for a programmed number of locations
in a programmed sequence. Accesses begin with the
registration of a BankActivate command which is then
followed by a Read or Write command.
The AS4C4M16S provides for programmable Read
or Write burst lengths of 1, 2, 4, 8, or full page, with a
burst termination option. An auto precharge function
may be enabled to provide a self-timed row precharge
that is initiated at the end of the burst sequence. The
refresh functions, either Auto or Self Refresh are easy
to use. By having a programmable mode register, the
system can choose the most suitable modes to
maximize its performance. These devices are well
suited for applications requiring high memory
bandwidth and particularly well suited to high
performance PC applications.
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VDD
LDQM
WE#
CAS#
RAS#
CS#
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
NC/RFU
UDQM
CLK
CKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
* Operating temperature range
- Commercial (0 ~ 70°C)
- Industrial (-40 ~ 85°C)
.
1
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 2. Block Diagram
Row
Decoder
BUFFER
CKE
1M x 16
CELL ARRAY
(BANK #A)
Column Decoder
COMMAND
DECODER
DQ0
DQ Buffer
CONTROL
SIGNAL
GENERATOR
~
CS#
RAS#
CAS#
WE#
DQ15
LDQM, UDQM
COLUMN
COUNTER
Row
Decoder
A10/AP
MODE
REGISTER
1M x 16
CELL ARRAY
(BANK #B)
Column Decoder
ADDRESS
BUFFER
Row
Decoder
A9
A11
BA0
BA1
REFRESH
COUNTER
Row
Decoder
~
A0
2
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Pin Descriptions
Table 3. Pin Details of AS4C4M16S
Symbol
Type
Description
CLK
Input
Clock: CLK is driven by the system clock. All SDRAM input signals are sample
on the positive edge of CLK. CLK also increments the internal burst counter and
controls the output registers.
CKE
Input
Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal. If
CKE goes low synchronously with clock (set-up and hold time same as other
inputs), the internal clock is suspended from the next clock cycle and the state of
output and burst address is frozen as long as the CKE remains low. When all
banks are in the idle state, deactivating the clock controls the entry to the Power
Down and Self Refresh modes. CKE is synchronous except after the device enters
Power Down and Self Refresh modes, where CKE becomes asynchronous until
exiting the same mode. The input buffers, including CLK, are disabled during
Power Down and Self Refresh modes, providing low standby power.
BA0,BA1
Input
Bank Activate: BA0, BA1 input select the bank for operation.
BA1
BA0
Select Bank
0
0
BANK #A
0
1
BANK #B
1
0
BANK #C
1
1
BANK #D
A0-A11
Input
Address Inputs: A0-A11 are sampled during the BankActivate command(row
address A0-A11) and Read/Write command (column address A0-A7 with A10
defining Auto Precharge) to select one location out of the 1M available in the
respective bank. During a Precharge command, A10 is sampled to determine if all
banks are to be precharged (A10 = HIGH). The address inputs also provide the
op-code during a Mode Register Set command.
CS#
Input
Chip Select: CS# enables (sampled LOW) and di sables (sampled HIGH) the
command decoder. All commands are masked when CS# is sampled HIGH. CS#
provides for external bank selection on systems with multiple banks. It is
considered part of the command code.
RAS#
Input
Row Address Strobe: The RAS# signal defines the operation commands in
conjunction with the CAS# and WE# signals and is latched at the positive edges of
CLK. When RAS# and CS# are asserted "LOW" and CAS# is asserted "HIGH,"
either the BankActivate command or t he Precharge command is selected by the
WE# signal. When the WE# is asserted "HIGH," the BankActivate command is
selected and the bank designated by BA is turned on to the active state. When the
WE# is asserted "LOW," the Precharge command is selected and the bank
designated by BA is switched to the idle state after the precharge operation.
CAS#
WE#
Input
Input
Column Address Strobe: The CAS# signal defines the operation commands in
conjunction with the RAS# and WE# signals and is latched at the positive edges of
CLK. When RAS# is held "HIGH" and CS# is asserted "LOW," the column access
is started by asserting CAS# "LOW." Then, the Read or Write command is
selected by asserting WE# "LOW" or "HIGH."
Write Enable: The WE# signal defines the operation commands in conjunction
with the RAS# and CAS# signals and is latched at the positive edges of CLK. The
WE# input is used to select the Bank Activate or Precharge command and Read or
Write command.
3
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
LDQM,
UDQM
DQ0-DQ15
NC/RFU
VDDQ
Input
Data Input/Output Mask: Controls output buffers in read mode and masks
Input data in write mode.
Input
/ Data I/O: The DQ0-15 input and output data are synchronized with the positive
Output edges of CLK. The I/Os are maskable during Reads and Writes.
Supply
No Connect: These pins should be left unconnected.
DQ Power: Provide isolated power to DQs for improved noise immunity.
( 3.3V± 0.3V )
VSSQ
Supply
DQ Ground: Provide isolated ground to DQs for improved noise immunity.
(0V)
VDD
Supply
Power Supply: +3.3V ± 0.3V
VSS
Supply
Ground
4
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Operation Mode
Fully synchronous operations are performed to latch the commands at the positive edges of CLK. Table 4
shows the truth table for the operation commands.
Table 4. Truth Table (Note (1), (2))
Command
State
CKEn-1 CKEn DQM BA0,1 A10 A0-9,11 CS# RAS# CAS# WE#
Idle(3)
H
X
X
V
BankPrecharge
Any
H
X
X
V
L
PrechargeAll
Any
H
X
X
X
Write
Active(3)
H
X
V
Write and AutoPrecharge
Active(3)
H
X
V
Read
Active(3)
H
X
V
V
L
Read and Autoprecharge
Active(3)
H
X
V
V
H
Mode Register Set
Idle
H
X
X
No-Operation
Any
H
X
X
X
X
Active(4)
H
X
X
X
Device Deselect
Any
H
X
X
AutoRefresh
Idle
H
H
SelfRefresh Entry
Idle
H
Idle
L
BankActivate
Burst Stop
SelfRefresh Exit
Row address
L
L
H
H
X
L
L
H
L
H
X
L
L
H
L
V
L
L
H
L
L
V
H
Column
address
(A0 ~ A7)
L
H
L
L
L
H
L
H
L
H
L
H
L
L
L
L
X
L
H
H
H
X
X
L
H
H
L
X
X
X
H
X
X
X
X
X
X
X
L
L
L
H
L
X
X
X
X
L
L
L
H
H
X
X
X
X
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
H
X
X
X
L
H
H
H
Column
address
(A0 ~ A7)
OP code
(SelfRefresh)
Clock Suspend Mode Entry
Power Down Mode Entry
Clock Suspend Mode Exit
Power Down Mode Exit
Active
Any(5)
H
H
L
X
L
X
X
X
X
X
X
X
Active
L
H
X
X
X
X
X
X
X
X
Any
L
H
X
X
X
X
H
X
X
X
L
H
H
H
X
X
X
X
X
X
(PowerDown)
Data Write/Output Enable
Active
H
X
L
X
X
X
Data Mask/Output Disable
Active
H
X
H
X
X
X
X
X
Note: 1. V=Valid, X=Don't Care L=Low level H=High level
2. CKEn signal is input level when commands are provided.
CKEn-1 signal is input level one clock cycle before the commands are provided.
3. These are states of bank designated by BA signal.
4. Device state is 1, 2, 4, 8, and full page burst operation.
5. Power Down Mode cannot enter in the burst operation.
When this command is asserted in the burst cycle, device state is clock suspend mode.
5
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Commands
1
BankActivate
(RAS# = "L", CAS# = "H", WE# = "H", BAs = Bank, A0-A11 = Row Address)
The Bank Activate command activates the idle bank designated by the BA0, 1 signal. By latching the
row address on A0 to A11 at the time of this command, the selected row access is initiated. The read or
write operation in the same bank can occur after a time delay of tRCD(min.) from the time of bank
activation. A subsequent BankActivate command to a different row in the same bank can only be issued
after the previous active row has been precharged (refer to the following figure). The minimum time
interval between successive Bank Activate commands to the same bank is defined by tRC(min.). The
SDRAM has four internal banks on the same chip and shares part of the internal circuitry to reduce chip
area; therefore it restri cts the back-to-back activation of the two banks. tRRD(min.) specifies the minimum
time required between activating different banks. After this command is used, the Write command and
the Block Write command perform the no mask write operation.
T0
T1
T2
T3
Tn+3
Tn+4
Tn+5
Tn+6
CLK
ADDRESS
Bank A
Row Addr.
Bank A
Col Addr.
Bank B
Row Addr.
R/W A with
AutoPrecharge
Bank B
Activate
RAS# - RAS# delay time(tRRD)
RAS# - CAS# delay(tRCD)
COMMAND
Bank A
Activate
NOP
NOP
Bank A
Row Addr.
NOP
Bank A
Activate
NOP
RAS# - Cycle time(tRC)
AutoPrecharge
Begin
Don’t Care
Figure 3. BankActivate Command Cycle (Burst Length = n)
2
Bank Precharge command
(RAS# = "L", CAS# = "H", WE# = "L", BAs = Bank, A10 = "L", A0-A9 and A11 = Don't care)
The BankPrecharge command precharges the bank designated by BA signal. The precharged bank
is switched from the active state to the idle state. This command can be asserted anytime after t RAS(min.)
is satisfied from the BankActivate command in the desired bank. The maximum time any bank can be
active is specified by tRAS(max.). Therefore, the precharge function must be performed in any active bank
within tRAS(max.). At the end of precharge, the precharged bank is still in the idle state and is ready to be
activated again.
3
Precharge All command
(RAS# = "L", CAS# = "H", WE# = "L", BAs = Don’t care, A10 = "H", A0-A9 and A11 = Don't care)
The PrechargeAll command precharges all banks simultaneously and can be issued even if all
banks are not in the active state. All banks are then switched to the idle state.
4
Read command
(RAS# = "H", CAS# = "L", WE# = "H", BAs = Bank, A10 = "L", A0-A7 = Column Address)
The Read command is used to read a burst of data on consecutive clock cycles from an active row
in an active bank. The bank must be active for at least t RCD(min.) before the Read command is issued.
During read bursts, the valid data-out element from the starting column address will be available following
the CAS# latency after the issue of the Read co mmand. Each subsequent data-out element will be valid
by the next positive clock edge (refer to the followi ng figure). The DQs go into high-impedance at the end
of the burst unless other command is initiated. The burst length, bur st sequence, and CAS# latency are
determined by the mode register, which is already programmed. A full-page burst will continue until
terminated (at the end of the page it will wrap to column 0 and continue.
6
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
T0
T1
READ A
NOP
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
CAS# latency=2
tCK2, DQ
NOP
DOUT A0
CAS# latency=3
tCK3, DQ
NOP
DOUT A1
DOUT A0
NOP
DOUT A2
DOUT A1
NOP
NOP
NOP
DOUT A3
DOUT A2
DOUT A3
Figure 4. Burst Read Operation (Burst Length = 4, CAS# Latency = 2, 3)
The read data appears on the DQs subject to the values on the DQM inputs two clocks earlier (i.e.
DQM latency is two clocks for output buffers). A read burst without the auto precharge function may be
interrupted by a subsequent Read or Write command to the same bank or the other active bank before
the end of the burst length. It may be interrupted by a BankPrecharge/ PrechargeAll command to the
same bank too. The interrupt coming from the Read command can occur on any clock cycle following a
previous Read command (refer to the following figure).
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
CAS# latency=2
tCK2, DQ
CAS# latency=3
tCK3, DQ
READ A
READ B
NOP
DOUT A0
NOP
NOP
NOP
DOUT B0
DOUT B1
DOUT B3
DOUT A0
DOUT B0
NOP
NOP
NOP
DOUT B2
DOUT B1
DOUT B2
DOUT B3
Figure 5. Read Interrupted by a Read (Burst Length = 4, CAS# Latency = 2, 3)
The DQM inputs are used to avoid I/O contention on the DQ pins when the interrupt comes from a
Write command. The DQMs must be asserted (HIGH) at least two clocks prior to the Write command to
suppress data-out on the DQ pins. To guarantee the DQ pins against I/O contention, a single cycle with
high-impedance on the DQ pins must occur between t he last read data and the Write command (refer to
the following three figures). If the data output of the burst read occurs at the second clock of the burst
write, the DQMs must be asserted (HIGH) at least one clock prior to the Write command to avoid internal
bus contention.
7
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
CLK
DQM
COMMAND
NOP
BANKA
ACTIVATE
NOP
NOP
READ A WRITE A
NOP
CAS# latency=2
tCK2, DQ
DIN A0
NOP
NOP
DIN A1
DIN A2
NOP
DIN A3
Must be Hi-Z before
the Write Command
Figure 6. Read to Write Interval (Burst Length ≥ 4, CAS# Latency = 2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
DQM
COMMAND
NOP
READ A
NOP
NOP
CAS# latency=3
tCK3, DQ
NOP
NOP
WRITE B
DOUT A0
DIN B0
NOP
NOP
DIN B1
DIN B2
Must be Hi-Z before
the Write Command
Don’t Care
Figure 7. Read to Write Interval (Burst Length ≧ 4, CAS# Latency = 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
DQM
COMMAND
NOP
CAS# latency=2
tCK2, DQ
NOP
READ A
NOP
NOP
WRITE B
DIN B0
Must be Hi-Z before
the Write Command
NOP
NOP
NOP
DIN B1
DIN B2
DIN B3
Don’t Care
Figure 8. Read to Write Interval (Burst Length ≥ 4, CAS# Latency = 2)
A read burst without the auto precharge function may be interrupted by a BankPrecharge/ Precharge All
command to the same bank. The following figure shows the optimum time that BankPrecharge/ Precharge All
command is issued in different CAS# latency.
8
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
Bank,
Col A
ADDRESS
Bank
Row
Bank(s)
tRP
COMMAND
READ A
NOP
CAS# latency=2
tCK2, DQ
NOP
NOP
Precharge
NOP
NOP
Activate
NOP
DOUT A0 DOUT A1 DOUT A2 DOUT A3
CAS# latency=3
tCK3, DQ
DOUT A0 DOUT A1 DOUT A2 DOUT A3
Don’t Care
Figure 9. Read to Precharge (CAS# Latency = 2, 3)
5 Read and AutoPrecharge command
(RAS# = "H", CAS# = "L", WE# = "H", BAs = Bank, A10 = "H", A0-A7 = Column Address)
The Read and AutoPrecharge command automatically performs the precharge operation after the
read operation. Once this command is given, any subsequent command cannot occur within a time delay of
{tRP(min.) + burst length}. At full-page burst, only the read operation is performed in this command and the
auto precharge function is ignored.
6 Write command
(RAS# = "H", CAS# = "L", WE# = "L", BAs = Bank, A10 = "L", A0-A7 = Column Address)
The Write command is used to write a burst of data on consecutive clock cycles from an active row in
an active bank. The bank must be active for at least t RCD(min.) before the Write command is issued. During
write bursts, the first valid data-in element will be registered coincident with the Write command.
Subsequent data elements will be registered on each successive positive clock edge (refer to the following
figure). The DQs remain with high-impedance at the end of the burst unless another command is initiated.
The burst length and burst sequence are determined by the mode register, which is already programmed. A
full-page burst will continue until terminated (at the end of the page it will wrap to column 0 and continue).
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
DQ
NOP
WRITE A
DIN A0
NOP
NOP
NOP
NOP
DIN A1
DIN A2
DIN A3
don’t care
NOP
NOP
NOP
The first data element and the write
are registered on the same clock edge
Figure 10. Burst Write Operation (Burst Length = 4)
9
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
A write burst without the auto precharge function may be interrupted by a subsequent Write,
BankPrecharge/PrechargeAll, or Read command before the end of the burst length. An interrupt coming
from Write command can occur on any clock cycle following the previous Write command (refer to the
following figure).
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
DQ
WRITE A
WRITE B
DIN A0
DIN B0
NOP
NOP
NOP
DIN B1
DIN B2
DIN B3
NOP
NOP
NOP
Figure 11. Write Interrupted by a Write (Burst Length = 4)
The Read command that interrupts a write burst without auto precharge function should be issued one
cycle after the clock edge in which the last data-in element is registered. In order to avoid data contention,
input data must be removed from the DQs at least one clock cycle before the first read data appears on
the outputs (refer to the following figure). Once the Read command is registered, the data inputs will be
ignored and writes will not be executed.
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
WRITE A
READ B
CAS# latency=2
tCK2, DQ
DIN A0
don’t care
CAS# latency=3
tCK3, DQ
DIN A0
don’t care
COMMAND
NOP
NOP
NOP
DOUT B0
don’t care
NOP
DOUT B1
DOUT B0
NOP
NOP
DOUT B2
DOUT B1
NOP
DOUT B3
DOUT B2
DOUT B3
Input data must be removed from the DQ
at least one clock cycle before the Read
data appears on the outputs to avoid data
contention
Figure 12. Write Interrupted by a Read (Burst Length = 4, CAS# Latency = 2, 3)
The BankPrecharge/PrechargeAll command that interrupts a write burst without t he auto precharge function
should be issued m cycles after the clock edge in which the last data-in element is registered, where m equals
tWR/tCK rounded up to the next whole number. In addition, the DQM signals must be used to mask input data,
starting with the clock edge following the last data- in element and ending with the clock edge on which the
BankPrecharge/PrechargeAll command is entered (refer to the following figure).
10
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
T0
T1
T2
T3
T4
T5
T6
T7
Activate
NOP
CLK
DQM
tRP
COMMAND WRITE
ADDRESS
NOP
NOP
BANK
COL n
Precharge
NOP
NOP
BANK(S)
ROW
tWR
DIN
N
DQ
DIN
N+1
Don’t Care
Note: The LDQM/UDQM can remain low in this example if the length of the write burst is 1 or 2.
Figure 13. Write to Precharge
7
Write and AutoPrecharge command (RAS# = "H", CAS# = "L", WE# = "L", BAs = Bank, A10 = "H", A0-A7
= Column Address)
The Write and AutoPrecharge command performs the precharge operation automatically after the write
operation. Once this command is given, any subsequent command cannot occur within a time delay of
{(burst length -1) + t WR + t RP(min.)}. At full-page burst, only t he write operation is performed in this
command and the auto precharge function is ignored.
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
CLK
COMMAND
Bank A
Activate
NOP
NOP
Write A
Auto Precharge
NOP
NOP
NOP
NOP
NOP
Bank A
Activate
tDAL
DQ
DIN A0
DIN A1
Begin AutoPrecharge
Bank can be reactivated at
completion of tDAL
tDAL=tWR+tRP
Figure 14. Burst Write with Auto-Precharge (Burst Length = 2)
8
Mode Register Set command (RAS# = "L", CAS# = "L", WE# = "L", A0-A11 = Register Data)
The mode register stores the data for controlling the various operating modes of SDRAM. The Mode
Register Set command programs the values of CAS# latency, Addressing Mode and Burst Length in the
Mode register to make SDRAM useful for a variety of different applications. The default values of the
Mode Register after power-up are undefined; therefore this command must be issued at the power-up
sequence. The state of pins A0~A9 and A11 in the same cycle is the data written to the mode register.
Two clock cycles are required to complete the write in the mode register (refer to the following figure).
The contents of the mode register can be changed using the same command and the clock cycle
requirements during operation as long as all banks are in the idle state.
11
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Table 5. Mode Register Bitmap
BA0,1
RFU*
A9
0
1
A11,A10 A9
RFU* WBL
Write Burst Length
Burst
Single Bit
A8
A7
Test Mode
A8
0
1
0
A6
A5
A4
CAS# Latency
A7
0
0
1
A3
BT
A2
A1
A0
Burst Length
A3
0
1
Test Mode
Normal
Vendor Use Only
Vendor Use Only
Burst Type
Sequential
Interleave
A2
A1
A0
Burst Length
A5
A4
CAS# Latency
0
0
0
1
0
0
Reserved
0
0
1
2
0
1
Reserved
0
1
0
4
1
0
2 clocks
0
1
1
8
1
1
3 clocks
1
1
1
Full Page (Sequential)
0
1
Reserved
All other Reserved
All other Reserved
*Note: RFU (Reserved for future use) should stay “0” during MRS cycle.
A6
0
0
0
0
1
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
CLK
CKE
tMRD
CS#
RAS#
CAS#
WE#
BA0,1
A10
Address Key
A0-A9,
A11
DQM
tRP
DQ
Hi-Z
PrechargeAll
Mode Register
Set Command
Any
Command
Don’t Care
Figure 15. Mode Register Set Cycle
12
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
• Burst Length Field (A2~A0)
This field specifies the data length of column access using the A2~A0 pins and selects the Burst Length to
be 2, 4, 8, or full page.
Table 6. Burst Length Field
A2
A1
A0
Burst Length
0
0
0
1
0
0
1
2
0
1
0
4
0
1
1
8
1
0
0
Reserved
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Full Page
• Burst Type Field (A3)
The Burst Type can be one of two modes, Interleave Mode or Sequential Mode.
Table 7. Burst Type Field
A3
0
Burst Type
Sequential
1
Interleave
• Burst Definition, Addressing Sequence of Sequential and Interleave Mode
Table 8. Burst Definition
Burst Length
2
4
8
Full page
Start Address
A2
A1
A0
X
X
0
X
X
1
X
0
0
X
0
1
X
1
0
X
1
1
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
location = 0-255
Sequential
0, 1
1, 0
0, 1, 2, 3
1, 2, 3, 0
2, 3, 0, 1
3, 0, 1, 2
0, 1, 2, 3, 4, 5, 6, 7
1, 2, 3, 4, 5, 6, 7, 0
2, 3, 4, 5, 6, 7, 0, 1
3, 4, 5, 6, 7, 0, 1, 2
4, 5, 6, 7, 0, 1, 2, 3
5, 6, 7, 0, 1, 2, 3, 4
6, 7, 0, 1, 2, 3, 4, 5
7, 0, 1, 2, 3, 4, 5, 6
n, n+1, n+2, n+3, …255, 0,
1, 2, … n-1, n, …
13
Interleave
0, 1
1, 0
0, 1, 2, 3
1, 0, 3, 2
2, 3, 0, 1
3, 2, 1, 0
0, 1, 2, 3, 4, 5, 6, 7
1, 0, 3, 2, 5, 4, 7, 6
2, 3, 0, 1, 6, 7, 4, 5
3, 2, 1, 0, 7, 6, 5, 4
4, 5, 6, 7, 0, 1, 2, 3
5, 4, 7, 6, 1, 0, 3, 2
6, 7, 4, 5, 2, 3, 0, 1
7, 6, 5, 4, 3, 2, 1, 0
Not Support
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
• CAS# Latency Field (A6~A4)
This field specifies the number of clock cycles from the assertion of the Read command to the first read
data. The minimum whole value of CAS# Latency depends on the frequency of CLK. The minimum
whole value satisfying the following formula must be programmed into this field.
tCAC(min) ≤ CAS# Latency X tCK
Table 9. CAS# latency Field
A6
A5
A4
CAS# Latency
0
0
0
Reserved
0
0
1
Reserved
0
1
0
2 clocks
0
1
1
3 clocks
1
X
X
Reserved
• Test Mode field (A8~A7)
These two bits are used to enter the test mode and must be programmed to "00" in normal operation.
Table 10. Test Mode Field
A8
A7
Test Mode
0
0
normal mode
0
1
Vendor Use Only
1
X
Vendor Use Only
• Write Burst Length (A9)
This bit is used to select the write burst mode. When the A9 bit is "0", the Burst-Read-Burst-Write mode is
selected. When the A9 bit is "1", the Burst-Read-Single-Write mode is selected.
Table 11. Write Burst Length
A9
0
Write Burst Mode
Burst-Read-Burst-Write
1
Burst-Read-Single-Write
Note: A10 and BA0, 1 should stay “L” during mode set cycle.
9 No-Operation command
(RAS# = "H", CAS# = "H", WE# = "H")
The No-Operation command is used to perform a NOP to the SDRAM which is selected (CS# is Low).
This prevents unwanted commands from being registered during idle or wait states.
10
Burst Stop command
(RAS# = "H", CAS# = "H", WE# = "L")
The Burst Stop command is used to terminate eit her fixed-length or full-page bursts. This command
is only effective in a read/write burst without the auto precharge func tion. The terminated read burst ends
after a delay equal to the CAS# latency (refer to the following figure). The termination of a write burst is
shown in the following figure.
14
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
READ A
NOP
NOP
NOP
Burst Stop
NOP
NOP
NOP
NOP
The burst ends after a delay equal to the CAS# latency
CAS# latency=2
tCK2, DQ
DOUT A0
A2
CAS# latency=3
tCK3, DQ
DOUT A1 DOUT
DOUT A3
DOUT A2
DOUT A3
DOUT A0 DOUT A1
Figure 16. Termination of a Burst Read Operation (Burst Length > 4, CAS# Latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
DQ
NOP
WRITE A
NOP
NOP
Burst Stop
DIN A0
DIN A1
DIN A2
don’t care
NOP
NOP
NOP
NOP
Figure 17. Termination of a Burst Write Operation (Burst Length = X)
11 Device Deselect command (CS# = "H")
The Device Deselect command disables the command decoder so that the RAS#, CAS#, WE# and
Address inputs are ignored, regardless of whether the CLK is enabled. This command is similar to the No
Operation command.
12 AutoRefresh command
(RAS# = "L", CAS# = "L", WE# = "H", CKE = "H", A11 = “Don‘t care, A0-A9 = Don't care)
The AutoRefresh command is used during normal operation of the SDRAM and is analogous to
CAS#-before-RAS# (CBR) Refresh in conventional DRAMs. This command is non-persistent, so it must
be issued each time a refresh is required. The addressing is generated by the internal refresh controller.
This makes the address bits a "don't care" during an AutoRefresh command. The internal refresh counter
increments automatically on every auto refresh cycle to all of the rows. The refresh operation must be
performed 4096 times within 64ms. The time required to complete the auto refresh operation is specified
by t RC(min.). To provide the AutoRefresh command, a ll banks need to be in the idle state and the device
must not be in power down mode (CKE is high in the previous cycle). This command must be followed by
NOPs until the auto refresh operation is completed. The precharge time requirement, t RP(min), must be
met before successive auto refresh operations are performed.
13
SelfRefresh Entry command
(RAS# = "L", CAS# = "L", WE# = "H", CKE = "L", A0-A9 = Don't care)
The SelfRefresh is another refresh mode available in the SDRAM. It is the preferred refresh mode
for data retention and low power operation. Once the SelfRefresh command is registered, all the inputs to
the SDRAM become "don't care" with the exception of CKE, which must remain LOW. The refresh
addressing and timing is internally generated to reduce power consumption. The SDRAM may remain in
SelfRefresh mode for an indefinite period. The SelfRefresh mode is exited by restarting the external clock
and then asserting HIGH on CKE (SelfRefresh Exit command).
15
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
14 SelfRefresh Exit command
This command is used to exit from the SelfRefres h mode. Once this command is registered, NOP or
Device Deselect commands must be issued for tXSR(min.) because time is required for the completion of
any bank currently being internally refreshed. If auto refresh cycles in bursts are performed during normal
operation, a burst of 4096 auto refresh cycles should be completed just prior to entering and just after
exiting the SelfRefresh mode.
15
Clock Suspend Mode Entry / PowerDown Mode Entry command (CKE = "L")
When the SDRAM is operating the burst cycle, the internal CLK is suspended (masked) from the
subsequent cycle by issuing this command (asserting CKE "LOW"). The device operation is held intact
while CLK is suspended. On the other hand, when all banks are in the idle state, this command performs
entry into the PowerDown mode. All input and output buffers (except the CKE buffer) are turned off in the
PowerDown mode. The device may not remain in the Clock Suspend or PowerDown state longer than
the refresh period (64ms) since the command does not perform any refresh operations.
16
Clock Suspend Mode Exit / PowerDown Mode Exit command (CKE= "H")
When the internal CLK has been suspended, the operation of the internal CLK is reinitiated from the
subsequent cycle by providing this command (asserting CKE "HIGH", the command should be NOP or
deselect). When the device is in the PowerDown mode, the device exits this mode and all disabled
buffers are turned on to the active state. tPDE (min.) is required when the device exits from the
PowerDown mode. Any subsequent commands can be issued after one clock cycle from the end of this
command.
17
Data Write / Output Enable, Data Mask / Output Disable command (DQM = "L", "H")
During a write cycle, the DQM signal functions as a Data Mask and can control every word of the
input data. During a read cycle, the DQM functions as the controller of output buffers. DQM is also used
for device selection, byte selection and bus control in a memory system.
16
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Table 12. Absolute Maximum Rating
Symbol
Item
- 6/7
Unit Note
VIN, VOUT
Input, Output Voltage
- 1.0 ~ 4.6
V
1
VDD, VDDQ
Power Supply Voltage
-1.0 ~ 4.6
V
1
TA
Ambient Temperature
0 ~ 70
°C
1
TSTG
Storage Temperature
- 55 ~ 125
°C
1
TSOLDER
Soldering Temperature (10 second)
260
°C
1
PD
Power Dissipation
1
W
1
IOUT
Short Circuit Output Current
50
mA
1
Table 13. Recommended D.C. Operating Conditions (TA = 0~70°C)
Symbol
Parameter
Min.
Typ.
Max.
VDD
Power Supply Voltage
3.0
3.3
3.6
V
2
VDDQ
Power Supply Voltage(for I/O Buffer)
3.0
3.3
3.6
V
2
VIH
LVTTL Input High Voltage
2.0
-
VDDQ+0.3 V
VIL
LVTTL Input Low Voltage
- 0.3
-
0.8 V
IIL
Input Leakage Current
( 0V ≤ VIN ≤ VDD, All other pins not under test = 0V )
- 10
IOL
Output Leakage Current
Output disable, 0V ≤ VOUT ≤ VDDQ)
- 10
VOH
LVTTL Output "H" Level Voltage
( IOUT = -2mA )
2.4
VOL
LVTTL Output "L" Level Voltage
( IOUT = 2mA )
-
-
-
-
-
Unit Note
2
2
10
µA
10
µA
-
V
0.4 V
Table 14. Capacitance (VDD = 3.3V, f = 1MHz, TA = 25°C)
Symbol
CI
CI/O
Parameter
Min.
Max.
Unit
Input Capacitance
2
5
pF
Input/Output Capacitance
4
6.5
pF
Note: These parameters are periodically sampled and are not 100% tested.
17
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Table 15. D.C. Characteristics (VDD = 3.3V ± 0.3V, TA = 0~70°C)
Description/Test condition
Symbol
Operating Current
tRC ≥ tRC(min), Outputs Open
One bank active
Precharge Standby Current in non-power down mode
tCK = 15ns, CS# ≥ VIH(min), CKE ≥ VIH
Input signals are changed every 2clks
Precharge Standby Current in non-power down mode
tCK = ∞, CLK ≤ VIL(max), CKE ≥ VIH
Precharge Standby Current in power down mode
tCK = 15ns, CKE ≤ VIL(max)
Precharge Standby Current in power down mode
tCK = ∞, CKE ≤ VIL(max)
Active Standby Current in non-power down mode
tCK = 15ns, CKE ≥ VIH(min), CS# ≥ VIH(min)
Input signals are changed every 2clks
Active Standby Current in non-power down mode
CKE ≥ VIH(min), CLK ≤ VIL(max), tCK = ∞
Operating Current (Burst mode)
tCK =tCK(min), Outputs Open, Multi-bank interleave
Refresh Current
tRC ≥ tRC(min)
Self Refresh Current
CKE ≤ 0.2V ; for other inputs VIH≧VDD - 0.2V, VIL ≤ 0.2V
18
-6
-7
Max.
Unit Note
3
IDD1
85
75
IDD2N
25
25
IDD2NS
15
15
IDD2P
2
2
IDD2PS
2
2
IDD3N
30
30
IDD3NS
25
25
IDD4
100
90
3, 4
IDD5
130
120
3
IDD6
2
2
mA
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Table 16. Electrical Characteristics and Recommended A.C. Operating Conditions
(VDD = 3.3V±0.3V, TA = 0~70°C) (Note: 5, 6, 7, 8)
Symbol
-6
A.C. Parameter
-7
Unit Note
Min.
Max.
Min.
Max.
60
-
63
-
18
-
21
-
18
-
21
-
12
-
14
-
42
-
49
-
2
-
2
-
1
-
1
-
CL* = 2
10
-
10
-
CL* = 3
6
-
7
-
tWR
Row cycle time
(same bank)
RAS# to CAS# delay
(same bank)
Precharge to refresh/row activate
command (same bank)
Row activate to row activate delay
(different banks)
Row activate to precharge time
(same bank)
Write recovery time
tCCD
CAS# to CAS# Delay time
tCK
Clock cycle time
tCH
Clock high time
2.5
-
2.5
-
10
tCL
Clock low time
2.5
-
2.5
-
10
Access time from CLK
(positive edge)
CL* = 2
-
6
-
6
10
tAC
CL* = 3
-
5.4
-
5.4
tOH
Data output hold time
2.5
-
2.7
-
tLZ
Data output low impedance
1
-
1
-
tHZ
Data output high impedance
-
5
-
5.4
8
tIS
Data/Address/Control Input set-up time
1.5
-
1.5
-
10
tIH
Data/Address/Control Input hold time
1
-
1
-
10
tPDE
Power Down Exit set-up time
tIS+tCK
-
tIS+tCK
-
tMRD
Mode Register Set Command Cycle Time
2
-
2
-
tCK
tREFI
Refresh Interval Time
-
15.6
-
15.6
µs
tRC+tIS
-
tRC+tIS
-
ns
tRC
tRCD
tRP
tRRD
tRAS
Exit Self-Refresh to Read Command
tXSR
* CL is CAS# Latency.
ns
tCK
9
ns
9
Note:
1. Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device.
2. All voltages are referenced to VSS. VIH (Max) = 4.6V for pulse width ≦3ns. VIL(Min) = -1.5V for pulse width
≦ 3ns.
3. These parameters depend on the cycle rate and these values are measured by the cycle rate under the
minimum value of tCK and tRC. Input signals are changed one time during every 2 tCK.
4. These parameters depend on the output loading. Specified values are obtained with the output open.
5. Power-up sequence is described in Note 11.
6. A.C. Test Conditions
19
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Table 17. LVTTL Interface
Reference Level of Output Signals
1.4V / 1.4V
Output Load
Reference to the Under Output Load (B)
Input Signal Levels
2.4V / 0.4V
Transition Time (Rise and Fall) of Input Signals
1ns
Reference Level of Input Signals
1.4V
1.4V
3.3V
50Ω
1.2KΩ
Output
Output
30pF
Z0=50Ω
870Ω
Figure 18.1 LVTTL D.C. Test Load (A)
30pF
Figure 18.2 LVTTL A.C. Test Load (B)
7. Transition times are measured between VIH and V IL. Transition (rise and fall) of input signals are in a fixed
slope (1 ns).
8.
tHZ defines the time in which the outputs achieve the open circuit condition and are not at reference levels.
9. If clock rising time is longer than 1 ns, ( tR / 2 -0.5) ns should be added to the parameter.
10. Assumed input rise and fall time tT ( tR & tF ) = 1 ns
If tR or t F is longer than 1 ns, transient time compensation should be considered, i.e., [(tr + tf)/2 - 1] ns should
be added to the parameter.
11. Power up Sequence
Power up must be performed in the following sequence.
1) Power must be applied to V DD and VDDQ(simultaneously) when CKE= “L”, DQM= “H” and all input signals
are held "NOP" state .
2) Start clock and maintain stable condition for minimum 200µs, then bring CKE= “H” and, it is
recommended that DQM is held "HIGH" (VDD levels) to ensure DQ output is in high impedance.
3) All banks must be precharged.
4) Mode Register Set command must be asserted to initialize the Mode register.
5) A minimum of 2 Auto-Refresh dummy cycles must be required to stabilize the internal circuitry of the
device.
* The Auto Refresh command can be issue before or after Mode Register Set command
20
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Timing Waveforms
Figure 19. AC Parameters for Write Timing (Burst Length=4)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
tCH
CKE
tCL
tIS
tIH
tIS
Begin Auto
Precharge Bank A
Begin Auto
Precharge Bank B
CS#
RAS#
CAS#
WE#
BA0,1
tIH
A10
RAx
RBx
RAy
tIS
A0-A9,
A11
RAx
CAx
RBx
CBx
RAy
CAy
DQM
tRCD
DQ
Hi-Z
tRC
Ax0
Activate
Command
Bank A
Ax1
Ax2
Ax3
Write with
Activate
Auto Precharge Command
Command
Bank B
Bank A
tDAL
Bx0
tIS
Bx1
Bx2
Bx3
Write with
Activate
Auto Precharge Command
Command
Bank A
Bank B
tIH
Ay0
Ay1
Write
Command
Bank A
tWR
Ay2 Ay3
Precharge
Command
Bank A
Don’t Care
21
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 20. AC Parameters for Read Timing (Burst Length=2, CAS# Latency=2)
T0
CLK
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
tCH tCL
tIS
CKE
tIS
Begin Auto
Precharge Bank B
tIH
tIH
CS#
RAS#
CAS#
WE#
BA0,1
tIH
A10
RAx
RBx
RAy
tIS
A0-A9,
A11
RAx
CAx
CBx
RBx
tRRD
RAy
tRAS
tRC
DQM
tAC
tLZ
tRCD
DQ
Hi-Z
Ax0
Activate
Command
Bank A
Read
Command
Bank A
tRP
tHZ
Ax1
tOH
Activate
Command
Bank B
Bx0
Bx1
tHZ
Read with
Precharge
Auto Precharge Command
Command
Bank A
Bank B
Activate
Command
Bank A
Don’t Care
22
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 21. Auto Refresh (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
tRP
tRCD
tRC
tRC
DQM
CAx
DQ
Ax0
Precharge All
Command
Auto Refresh
Command
Auto Refresh
Command
Activate
Command
Bank A
Ax1
Read
Command
Bank A
Don’t Care
23
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 22. Power on Sequence and Auto Refresh
T0
T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
High Level
is reguired
CKE
Minimum for 2 Refresh Cycles are required
CS#
RAS#
CAS#
WE#
BA0,1
A10
Address Key
A0-A9,
A11
DQM
tRP
DQ
tMRD
Hi-Z
Precharge All
Command
Inputs must be
Stable for 200 µs
2nd Auto Refresh(*)
Command
1st Auto Refresh(*)
Command
Any
Command
Mode Register
Set Command
Note(*):The Auto Refresh command can be issue before or after Mode Register Set command
24
Don’t Care
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 23. Self Refresh Entry & Exit Cycle
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19
CLK
*Note 1
*Note 2
CKE
tXSR
*Note 5
*Note 3, 4
tIS tIH
*Note 8
tPDE
*Note 6
*Note 7
tIS
CS#
RAS#
*Note 9
CAS#
BA0,1
A0-A9,
A11
WE#
DQM
DQ
Hi-Z
Self Refresh Entry
Hi-Z
Self Refresh Exit
Auto Refresh
Don’t Care
Note: To Enter SelfRefresh Mode
1. CS#, RAS# & CAS# with CKE should be low at the same clock cycle.
2. After 1 clock cycle, all the inputs including the system clock can be don't care except for CKE.
3. The device remains in SelfRefresh mode as long as CKE stays "low".
4. Once the device enters SelfRefresh mode, minimum tRAS is required before exit from SelfRefresh.
To Exit SelfRefresh Mode
5. System clock restart and be stable before returning CKE high.
6. Enable CKE and CKE should be set high for valid setup time and hold time.
7. CS# starts from high.
8. Minimum tXSR is required after CKE going high to complete SelfRefresh exit.
9. 4096 cycles of burst AutoRefresh is required before Self Refresh entry and after SelfRefresh exit if the
system uses burst refresh.
25
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 24.1. Clock Suspension During Burst Read (Using CKE)
(Burst Length=4, CAS# Latency=2)
T0
T1 T2 T3 T4
T5
T6 T7 T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
DQM
tHZ
DQ
Hi-Z
Ax0
Activate
Cammand
Bank A
Read
Command
Bank A
Ax1
Clock Suspend
1 Cycle
Ax2
Ax3
Clock Suspend
2 Cycles
Clock Suspend
3 Cycles
Don’t Care
26
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 24.2. Clock Suspension During Burst Read (Using CKE)
(Burst Length=4, CAS# Latency=3)
T0
T1 T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
DQM
tHZ
DQ
Hi-Z
Ax0
Activate
Cammand
Bank A
Read
Command
Bank A
Ax1
Ax2
Clock Suspend Clock Suspend
2 Cycles
1 Cycle
27
Ax3
Clock Suspend
3 Cycles
Don’t Care
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 25. Clock Suspension During Burst Write (Using CKE)
(Burst Length=4)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
DQM
DQ
Hi-Z
DAx0
Activate
Cammand
Bank A
DAx1
DAx2
Clock Suspend Clock Suspend
2 Cycles
1 Cycle
DAx3
Clock Suspend
3 Cycles
Don’t Care
Write
Command
Bank A
28
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 26. Power Down Mode and Clock Suspension (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
tIH tIS
tPDE
CKE
Valid
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
DQM
tHZ
DQ
Hi-Z
Ax0 Ax1
ACTIVE
STANDBY
Activate
Cammand
Bank A
Power Down
Mode Entry
Read
Command
Bank A
Power Down
Mode Exit
Ax2
Ax3
Clock Suspension Clock Suspension Precharge
Command
End
Start
Bank A
PRECHARGE
STANDBY
Power Down
Mode Exit
Any
Commad
Power Down
Mode Entry
Don’t Care
29
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 27.1. Random Column Read (Page within same Bank)
(Burst Length=4, CAS# Latency=2)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAw
x
A0-A9,
A11
RAw
RAz
CAw
CAx
CAy
RAz
CAz
DQM
DQ
Hi-Z
Aw0 Aw1 Aw2 Aw3 Ax0 Ax1
Activate
Cammand
Bank A
Read
Command
Bank A
Read
Read
Command Command
Bank A
Bank A
Az0
Ay0 Ay1 Ay2 Ay3
Precharge
Command
Bank A
Activate
Command
Bank A
Read
Command
Bank A
Don’t Care
30
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 27.2. Random Column Read (Page within same Bank)
(Burst Length=4, CAS# Latency=3)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAw
x
A0-A9,
A11
RAw
RAz
CAw
CAx
CAy
RAz
CAz
DQM
DQ Hi-Z
Aw0 Aw1 Aw2 Aw3 Ax0
Activate
Cammand
Bank A
Read
Command
Bank A
Read
Read
Command Command
Bank A
Bank A
Ax1 Ay0 Ay1
Ay2 Ay3
Precharge
Command
Bank A
Activate
Command
Bank A
Read
Command
Bank A
Don’t Care
31
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 28. Random Column Write (Page within same Bank)
(Burst Length=4)
T0
T1 T2 T3 T4 T5 T6 T7
T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RBw
x
A0-A9,
A11
RBw
RBz
CBw
CBx
DBw0 DBw1 DBw2 DBw3
DBy3
DBx0 DBx1 DBy0 DBy1 DBy2
CBy
RBz
CBz
DQM
DQ
Hi-Z
Activate
Cammand
Bank B
Write
Command
Bank B
Write
Write
Command Command
Bank B
Bank B
DBz0 DBz1
Precharge
Command
Bank B
Activate
Command
Bank B
Write
Command
Bank B
Don’t Care
32
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 29.1. Random Row Read (Interleaving Banks)
(Burst Length=8, CAS# Latency=2)
T0
T1
T2 T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RBx
A0-A9,
A11
RBx
tRCD
RAx
CBx
RBy
RAx
RBy
CAx
tAC
CBy
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank B
Bx0
Read
Command
Bank B
Bx1
Bx2
Bx3
Bx4
Activate
Command
Bank A
Bx5
Bx6 Bx7
Ax0
Read
Command
Bank A
Precharge
Command
Bank B
33
Ax1
Ax2
Ax3
Ax4
Ax5
Ax6 Ax7
Activate
Command
Bank B
Read
Command
Bank B
Don’t Care
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 29.2. Random Row Read (Interleaving Banks)
(Burst Length=8, CAS# Latency=3)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RBx
A0-A9,
A11
RBx
RAx
CBx
RBy
CAx
RAx
tAC
tRCD
RBy
CBy
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank B
Bx0 Bx1 Bx2 Bx3 Bx4
Ax1
Read
Command
Bank B
Activate
Command
Bank A
Bx5 Bx6 Bx7 Ax0
Read
Precharge
Command Command
Bank B
Bank A
Ax2
Ax3
Activate
Command
Bank B
Ax4 Ax5 Ax6 Ax7 By0
Read
Precharge
Command Command
Bank B
Bank A
Don’t Care
34
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 30. Random Row Write (Interleaving Banks)
(Burst Length=8)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBx
RAy
CBx
RAy
tWR*
tRCD
tRP
CAy
tWR*
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
DAx0 DAx1 DAx2 DAx3 DAx4 DAx5 DAx6 DAx7 DBx0 DBx1 DBx2
Write
Command
Bank A
Activate
Command
Bank B
Write
Command
Bank B
DBx3 DBx4 DBx5 DBx6 DBx7 DAy0 DAy1 DAy2 DAy3
Precharge
Command
Bank A
Activate
Command
Bank A
Write
Precharge
Command Command
Bank A
Bank B
Don’t Care
* tWR > tWR (min.)
35
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 31.1. Read and Write Cycle (Burst Length=4, CAS# Latency=2)
T0
T1
T2 T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAy
CAx
CAz
DQM
DQ
Hi-Z
Ax0 Ax1
Activate
Cammand
Bank A
Read
Command
Bank A
Ax2
Ax3
DAy0 DAy1
DAy3
Write
The Write Data
Command is Masked with a
Bank A
Zero Clock
Latency
Az0
Read
Command
Bank A
Az1
Az3
The Read Data
is Masked with a
Two Clock
Latency
Don’t Care
36
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 31.2. Read and Write Cycle (Burst Length=4, CAS# Latency=3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
CAy
CAz
DQM
DQ
Hi-Z
Ax0
Activate
Cammand
Bank A
Read
Command
Bank A
Ax1 Ax2
Ax3
DAy0
DAy1
Az0
DAy3
Write
The Write Data
Command is Masked with a
Bank A
Zero Clock
Latency
Read
Command
Bank A
Az1
Az3
The Read Data
is Masked with a
Two Clock
Latency
Don’t Care
37
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 32.1. Interleaving Column Read Cycle (Burst Length=4, CAS# Latency=2)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RRAx
A0-A9,
A11
RAx
RBx
CBw
Ax0
Ax1 Ax2 Ax3
CAy
tRCD
DQM
DQ
RBx
Hi-Z
Activate
Cammand
Bank A
CBx
CBy
CAy
CBz
tAC
Activate
Read
Command Command
Bank B
Bank A
Read
Command
Bank B
Bw0 Bw1 Bx0 Bx1 By0
By1 Ay0 Ay1 Bz0 Bz1 Bz2 Bz3
Read
Read
Read
Read
Command
CommandCommand
Command
Bank B
Bank B Bank A
Bank B
Precharge
Command
Bank A
Precharge
Command
Bank B
Don’t Care
38
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 32.2. Interleaved Column Read Cycle (Burst Length=4, CAS# Latency=3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAx
tRCD
DQM
DQ
RBx
RBx
CBx
CBz
CAy
tAC
Hi-Z
Ax0
Activate
Cammand
Bank A
CBy
Read
Command
Bank A
Activate
Command
Bank B
Ax1
Ax2
Ax3
Bx0
Bx1
By0
Read
Read
Read
Command Command Command
Bank B
Bank B
Bank B
By1 Bz0
Bz1 Ay0
Read
Precharge
Command Command
Bank A
Bank B
Ay1
Ay2
Ay3
Precharge
Command
Bank A
Don’t Care
39
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 33. Interleaved Column Write Cycle (Burst Length=4)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBw
CAx
RBw
CBw
CBx
CBy
CAy
CBz
tRCD
tWR
tWR
DQM
tRRD>tRRD(min)
DQ
Hi-Z
DAx0 DAx1 DAx2 DAx3 DBw0 DBw1 DBx0 DBx1 DBy0 DBy1 DAy0 DAy1 DBz0
Activate
Cammand
Bank A
Write
Command
Bank A
Activate
Command
Bank B
DBz1 DBz2 DBz3
Write
Write
Write
Write
Write
Command CommandCommand CommandCommand
Bank B Bank B Bank B Bank A Bank B
Precharge
Command
Bank A
Precharge
Command
Bank B
Don’t Care
40
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 34.1. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
Begin Auto
Precharge
Bank A
Begin Auto
Precharge
Bank B
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBy
RBx
CBx
RAy
RAz
RBy
CBy
RAz
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
Ax0 Ax1 Ax2
Activate
Read
Command Command
Bank B
Bank A
Ax3
Read with
Auto Precharge
Command
Bank B
Bx0
Bx1
Bx2
Bx3 Ay0
Ay1
Ay2 Ay3
Activate
Command
Bank B
Read with
Auto Precharge
Command
Bank A
By0
By1
By2
Activate
Command
Bank A
Read with
Auto Precharge
Command
Bank B
Don’t Care
41
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 34.2. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=3)
T0
T1
T2 T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
Begin Auto
Precharge
Bank B
Begin Auto
Precharge
Bank A
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBx
RBy
CBx
CAy
RBy
CBy
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
Ax0 Ax1 Ax2 Ax3 Bx0 Bx1 Bx2 Bx3 Ay0 Ay1 Ay2 Ay3
Read
Command
Bank A
Activate
Command
Bank B
Read with
Auto Precharge
Command
Bank B
Read with
Auto Precharge
Command
Bank A
Activate
Command
Bank B
By0 By1 By2
Read with
Auto Precharge
Command
Bank B
Don’t Care
42 Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 34.1. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
Begin Auto
Precharge
Bank A
Begin Auto
Precharge
Bank B
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBy
RBx
CBx
RAy
RAz
RBy
CBy
RAz
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
Ax0 Ax1 Ax2
Activate
Read
Command Command
Bank B
Bank A
Ax3
Read with
Auto Precharge
Command
Bank B
Bx0
Bx1
Bx2
Bx3 Ay0
Ay1
Ay2 Ay3
Activate
Command
Bank B
Read with
Auto Precharge
Command
Bank A
By0
By1
By2
Activate
Command
Bank A
Read with
Auto Precharge
Command
Bank B
Don’t Care
43
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 36.1. Full Page Read Cycle (Burst Length=Full Page, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBy
RBx
CBx
RBy
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
Ax Ax+1 Ax+2 Ax-2 Ax-1
Read
Activate
Command Cammand
Bank A
Bank B
Ax
Ax+1
Bx
Bx+1 Bx+2 Bx+3 Bx+4 Bx+5 Bx+6
Read
Command
Bank B
Precharge
Command
Bank B
Activate
Command
Bank B
Burst Stop
Command
The burst counter wraps
from the highest order
page address back to zero
during this time interval
Full Page burst operation does not
terminate when the burst length is satisfied;
the burst counter increments and continues
bursting beginning with the starting address
44
Don’t Care
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 34.1. Auto Precharge after Read Burst (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
Begin Auto
Precharge
Bank A
Begin Auto
Precharge
Bank B
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBy
RBx
CBx
RAy
RAz
RBy
CBy
RAz
tRP
DQM
DQ
Hi-Z
Activate
Cammand
Bank A
Ax0 Ax1 Ax2
Activate
Read
Command Command
Bank B
Bank A
Ax3
Read with
Auto Precharge
Command
Bank B
Bx0
Bx1
Bx2
Bx3 Ay0
Ay1
Ay2 Ay3
Activate
Command
Bank B
Read with
Auto Precharge
Command
Bank A
By0
By1
By2
Activate
Command
Bank A
Read with
Auto Precharge
Command
Bank B
Don’t Care
45
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 37. Full Page Write Cycle (Burst Length=Full Page)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RBx
CAx
RBy
CBx
RBx
RBy
DQM
DQ Hi-Z
Activate
Cammand
Bank A
Data is ignored
DAx
1
DAx+1 DAx+2 DAx+3 DAx-
Write
Activate
Command Cammand
Bank A
Bank B
DAx
DAx+1
DBx
DBx+5
Write
Command
Bank B
DBx+1 DBx+2 DBx+3 DBx+4
Precharge
Command
Bank B
Burst Stop
The burst counter wraps
Command
from the highest order
page address back to zero Full Page burst operation does not
terminate when the burst length is
during this time interval
satisfied; the burst counter increments
and continues bursting beginning with
the starting address
46 Rev2.0 May 2014
Activate
Command
Bank B
Don’t Care
AS4C4M16S
FEBRUARY 2011
Figure 38. Byte Write Operation (Burst Length=4, CAS# Latency=2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
CAy
CAx
CAz
DQMm
DQMn
DQ0-DQ7
Ax0 Ax1
DQ8-DQ15
Ax2
Ax1 Ax2 Ax3
Activate
Cammand
Bank A
Read
Command
Bank A
Upper Byte
is masked
DAy1 DAy2
DAy0 DAy1
Az0
DAy3
Upper Byte
Lower Byte Write
Command is masked
is masked
Bank A
Read
Command
Bank A
Az1
Az2
Az1
Az2
Az3
Lower Byte
is masked
Lower Byte
is masked
Don’t Care
47
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 39. Random Row Read (Interleaving Banks)
(Burst Length=4, CAS# Latency=2)
T0
T1
T2 T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE High
Begin Auto
Precharge
Bank B
Begin Auto
Precharge
Bank A
Begin Auto
Precharge
Bank B
Begin Auto
Precharge
Bank A
CS#
RAS#
CAS#
WE#
BA0,1
A10
A0-A9,
A11
RBu
RBu
RAu
CBu
RAv
RBv
RAu
CAu
RBv
CBv
RBw
RAv
CAv
tRP
tRP
RBw
tRP
DQM
DQ
Bu0
Activate
Command
Bank B
Activate
Command
Bank A
Read
Bank B
with Auto
Precharge
Bu1
Bu2
Bu3
Au0
Au1
Au2
Au3
Activate
Command
Bank B
Bv0
Bv1
Bv2
Bv3
Av1
Activate
Command
Bank A
Read
Bank A
with Auto
Precharge
Read
Bank B
with Auto
Precharge
Read
Bank A
with Auto
Precharge
Av0
Av2
Activate
Command
Bank B
Don’t Care
48
Rev2.0 May 2014
Av3
AS4C4M16S
FEBRUARY 2011
Figure 40. Full Page Random Column Read (Burst Length=Full Page, CAS# Latency=2)
T0
T1 T2 T3 T4
T5 T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
A0-A9,
A11
RAx
RBx
RAx
RBx
RBw
CAx
CBx CAy
CBy
CAz
RBw
CBz
tRP
DQM
tRRD
DQ
tRCD
Hi-Z
Ax0 Ax1 Bx0 Ay0 Ay1 By0 By1 Az0 Az1 Az2 Bz0 Bz1 Bz2
Activate
Cammand
Bank A
Activate
Command
Bank B
Read
Command
Bank B
Read
Command
Bank A
Read
Read
Command Command
Bank B
Bank A
Read
Command
Bank A
Read
Command
Bank B
Precharge Command
Bank B (Precharge
Temination)
Activate
Command
Bank B
Don’t Care
49
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 41. Full Page Random Column Write (Burst Length=Full Page)
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
RBx
A0-A9,
A11
RAx
RBx CAx
RBw
CBx
CAy
CBy
CAz
RBw
CBz
tWR
tRP
DQM
tRCD
tRRD
DQ
Hi-Z
DAx0 DAx1 DBx0 DAy0
DAy1 DBy0 DBy1 DAz0 DAz1 DAz2 DBz0 DBz1 DBz2
Activate
Write
Activate
Write
Write
Cammand Command
Command
Command Command
Bank B
Bank A
Bank B
Bank B
Bank A
Write
Write
Command
Command
Bank A
Bank A
Precharge
Command Bank B
(Precharge Temination)
Write
Command
Bank B
Activate
Command
Bank B
Write Data
are masked
Figure 42. Precharge Termination of a Burst
(Burst Length=4, 8 or Full Page, CAS# Latency=3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T22
CLK
CKE
High
CS#
RAS#
CAS#
WE#
BA0,1
A10
RAx
A0-A9,
A11
RAx
RAy
RAz
RAy
CAx
tWR
CAy
RAz
tRP
tRP
DQM
DQ
Ay0
DAx0 DAx1
Activate
Cammand
Bank A
Write
Command
Bank A
Precharge
Command
Bank A
Activate
Command
Bank A
Precharge Termination
of a Write Burst
Read
Command
Bank A
Ay1
Precharge
Command
Bank A
Ay2
Activate
Command
Bank A
Precharge Termination
of a Read Burst
Write Data are masked
Don’t Care
50
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
Figure 43. 54 Pin TSOP II Package Outline Drawing Information
Symbol
A
A1
A2
B
C
D
E
e
HE
L
L1
S
y
θ
Min
Dimension in inch
Nom
Max
--0.002
0.035
0.01
0.004
0.87
0.395
--0.455
0.016
----0°
----0.039
0.014
0.006
0.875
0.400
0.031
0.463
0.02
0.032
0.028
-----
0.047
0.008
0.043
0.018
0.008
0.88
0.405
--0.471
0.024
----0.004
8°
Min
Dimension in mm
Nom
Max
--0.05
0.9
0.25
0.12
22.09
10.03
--11.56
0.4
------0°
----1.0
0.35
0.165
22.22
10.16
0.8
11.76
0.5
0.84
0.71
-----
1.2
0.2
1.1
0.45
0.21
22.35
10.29
--11.96
0.6
----0.1
8°
Notes:
1. Dimension D&E do not include interlead flash.
2. Dimension B does not include dambar protrusion/intrusion.
3. Dimension S includes end flash.
4. Controlling dimension: mm
51
Rev2.0 May 2014
AS4C4M16S
FEBRUARY 2011
ORDERING INFORMATION
Alliance
Organization
VCC
Range
Package
Operating Temp
Speed
MHz
AS4C4M16S-6TCN
4M x 16
3.3V+/-0.3V
54 TSOP II
Commercial
166
AS4C4M16S-6TIN
4M x 16
3.3V+/-0.3V
54 TSOP II
Industrial
166
AS4C4M16S-7TCN
4M x 16
3.3V+/-0.3V
54 TSOP II
Commercial
143
PART NUMBERING SYSTEM
AS4C
4M44M16S
S= SDRAM
SDRAM prefix
64Mb (4Mx16)
-6
Speed
T=TSOP Package
54 pin TSOP II
52
C
N
Temperature Range N = Lead Free
RoHS
C = Commercial
compliant part
(0 - 70°C)
I = Industrial
(-45 - 85°C)
Rev2.0 May 2014
Similar pages