ZETTLER AZ2501P2-1A-9D 50 amp latching power relay Datasheet

AZ2501P
50 AMP LATCHING
POWER RELAY
FEATURES
•
•
•
•
•
•
•
50 Amp switching
Heavy loads to 13850 VA
4 kV dielectric strength
8 mm creepage distance
Manual switch available
Epoxy sealed version available
UL, CUR file E44211
CONTACTS
GENERAL DATA
Arrangement
SPDT (1 Form C),
SPST (1 Form A)
Ratings
Resistive load:
Max. switched power: 13850 VA
Max. switched current: 50 A
Max. switched voltage: 440 VAC
Rated Load
UL, CUR
1 Form A (SPST)
50 A at 277 VAC, resistive, 70°C, 100k cycles
20 A at 347 VAC, resistive, 70°C, 30k cycles
5000 W at 240 VAC, tungsten, 40°C, 30k cycles
120 LRA / 20 FLA, at 120 VAC, 40°C, 30k cycles
102 LRA / 17 FLA, at 240 VAC, 40°C, 30k cycles
84 LRA / 14 FLA, at 277 VAC, 40°C, 30k cycles
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 106
1 x 105 at 50 A 250 VAC Res. (SPST)
Set and Reset
Pulse Duration
50 ms minimum at nominal coil voltage
Set Time (typical)
15 ms at nominal coil voltage
Reset Time (typical)
15 ms at nominal coil voltage
Dielectric Strength
4000 Vrms coil to contact
(at sea level for 1 min.) 1500 Vrms between open contacts
Insulation
Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Creepage Distance
8 mm (1 Form A), 6 mm (1 Form C)
1 Form C (SPDT)
40 A at 277 VAC, general use, 70°C, 30k cycles
Ambient Temperature
Operating
At nominal coil voltage
-40°C (-40°F) to 70°C (158°F)
Material
Silver tin oxide
Vibration
1.5mm DA at 10–55 Hz
Resistance
< 50 milliohms initially
(at rated current, voltage drop method)
Shock
COIL
Power
At Pickup Voltage
(typical)
Temperature
Operating
10 g, 11 ms, 1/2 sine (no false operation)
Non-Operating 100 g, 11 ms, 1/2 sine (no damage)
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy
.96 W single coil
1.9 W dual coil
Max. Solder Temp.
270°C (518°F)
Max. 105°C (221°F)
Max. Solder Time
5 seconds
Weight
32 grams
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
4. Initial state of contacts may be changed during transportation or shock!
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2014-09-08
AZ2501P
RELAY ORDERING DATA
COIL SPECIFICATIONS - STANDARD SINGLE COIL
Nominal Coil
VDC
Must Operate
VDC
Max. Continuous
VDC [1]
ORDER NUMBER*
Coil Resistance
Ohm ± 10%
1 Form A
1 Form C
AZ2501P1-1C-6D
6
4.8
7.8
24
AZ2501P1-1A-6D
9
7.2
11.7
54
AZ2501P1-1A-9D
AZ2501P1-1C-9D
12
9.6
15.6
96
AZ2501P1-1A-12D
AZ2501P1-1C-12D
24
19.2
31.2
384
AZ2501P1-1A-24D
AZ2501P1-1C-24D
48
38.4
62.4
1536
AZ2501P1-1A-48D
AZ2501P1-1C-48D
COIL SPECIFICATIONS - STANDARD DUAL COIL
ORDER NUMBER*
Nominal Coil
VDC
Must Operate
VDC
Max. Continuous
VDC [1]
Coil Resistance
Ohm ± 10%
1 Form A
1 Form C
6
4.8
7.8
12
AZ2501P2-1A-6D
AZ2501P2-1C-6D
9
7.2
11.7
27
AZ2501P2-1A-9D
AZ2501P2-1C-9D
12
9.6
15.6
48
AZ2501P2-1A-12D
AZ2501P2-1C-12D
24
19.2
31.2
192
AZ2501P2-1A-24D
AZ2501P2-1C-24D
48
38.4
62.4
768
AZ2501P2-1A-48D
AZ2501P2-1C-48D
* For epoxy sealed version (not allowed with manual switch) add suffix “E”.
For manual switch add suffix “W”.
For PCB retaining stud add suffix “K”.
For reverse polarity coil add suffix “R”.
NOTE: [1] Max. continuous voltage should not be applied for more then 60 seconds.
MECHANICAL DATA
PC BOARD LAYOUT
Suffix “W” only
.376
[9.6]
.601MAX
[15.3]
1.547MAX
[39.3]
.295
[7.5]
0.177
[4.5]
.266
[6.8]
.132
[3.35]
.118
[3.0]
1.083
[27.5]
.472
[12.0]
.167
[4.3]
3x
.041
[1.04]
2
5
4
3x
.078
[1.98]
.205
[5.2]
.394
[10.0]
3
1.201MAX
[30.5]
6
1
.143
[3.63]
Suffix “K” only
.083
[2.1]
Viewed toward terminals
.376
[9.6]
.295
[7.5]
.132
[3.35]
1.083
[27.5]
.472
[12.0]
.266
[6.8]
.167
[4.3]
.024
[0.60]
.031
[0.8]
.094
[2.4]
2
3
.394
[10.0]
5
4
1
.059
[1.5]
.063
[1.6]
Terminal 5 omitted (single coil)
6
.094
[2.4]
.024
[0.60]
Suffix “K” only
Terminal 6 omitted (form A)
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2014-09-08
AZ2501P
WIRING DIAGRAMS
4
4
4
3
4
6
6
1
2
SPST&Single Coil
3
3
3
1
2
SPDT&Single Coil
1 5 2
1 5 2
SPST&Double Coil
SPDT&Double Coil
NOTE:
Standard Polarity type:
1. “Single Coil Latching Version”
(1) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected.
(2) After energizing 2 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected.
2. “Double Coil Latching Version”
(1) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is connected.
(2) After energizing 5 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is disconnected.
Reverse Polarity type:
1. “Single Coil Latching Version”
(1) After energizing 1 (-) and 2 (+), 50ms pulse, terminal 3 and 4 is connected.
(2) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is disconnected.
2. “Double Coil Latching Version”
(1) After energizing 5 (-) and 1 (+), 50ms pulse, terminal 3 and 4 is connected.
(2) After energizing 5 (-) and 2 (+), 50ms pulse, terminal 3 and 4 is disconnected.
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2014-09-08
Similar pages