AD AD642K Precision, low cost dual bifet op amp Datasheet

a
FEATURES
Matched Offset Voltage
Matched Offset Voltage Over Temperature
Matched Bias Current
Crosstalk: –124 dB @ 1 kHz
Low Bias Current: 35 pA max Warmed Up
Low Offset Voltage: 500 mV max
Low Input Voltage Noise: 2 mV p-p
High Open Loop Gain
Low Quiescent Current: 2.8 mA max
Low Total Harmonic Distortion
Standard Dual Amplifier Pin Out
Available in Hermetic Metal Can Package and Chip Form
MIL-STD-883B Processing Available
Single Version Available: AD542
PRODUCT DESCRIPTION
The AD642 is a pair of matched high speed monolithic BiFET
operational amplifier fabricated with the most advanced bipolar,
JFET and laser trimming technologies. The AD642 offers
matched bias currents that are significantly lower than currently
available monolithic dual FET input operational amplifiers:
35 pA max matched to 25 pA for the AD642K and L; 75 pA
max, matched to 35 pA for the AD642J and S. In addition, the
offset voltage is laser trimmed to less than 0.5 mV and matched
to 0.25 mV for the AD642L, 1.0 mV and matched to 0.5 mV for
the AD642K, utilizing Analog’s laser-wafer trimming (LWT)
process.
The tight matching and temperature tracking between the
operational amplifiers is achieved by ion-implanted JFETs and
laser-wafer trimming. Ion-implantation permits the fabrication of
precision, matched JFETs on a monolithic bipolar chip. The
optimizes the process to product matched bias currents which
have lower initial bias currents than other popular BiFET op
amps. Laser-wafer trimming each amplifier’s input offset voltage
assures tight initial match and combined with superior IC
processing guarantees offset voltage tracking over the temperature range.
The AD642 is recommended for applications in which excellent
ac and dc performance is required. The matched amplifiers
provide a low-cost solution for true instrumentation amplifiers,
log ratio amplifiers, and output amplifiers for four quadrant
multiplying D/A converters such as the AD7541.
Precision, Low Cost
Dual BiFET Op Amp
AD642
PIN CONFIGURATION
The AD642 is available in four versions: the ‘‘J’’, ‘‘K’’ and ‘‘L,’’
all specified over the 0°C to +70°C temperature range and one
version, ‘‘S,’’ over the –55°C to +125°C extended operating
temperature range. All devices are packaged in the hermeticallysealed, TO-99 metal can or available in chip form.
PRODUCT HIGHLIGHTS
1. The AD642 has tight matching specifications to ensure high
performance, eliminating the need to match individual
devices.
2. Analog Devices, unlike some manufacturers, specifies each
device for the maximum bias current at either input in the
warmed-up condition, thus assuring the user that the AD642
will meet its published specifications in actual use.
3. Laser-wafer-trimming reduces offset voltage to as low as
0.5 mV max and matched side to side to 0.25 mV
(AD642L), thus eliminating the need for external nulling.
4. Low voltage noise (2 µV, p-p), and high open loop gain
enhance the AD642’s performance as a precision op amp.
5. The standard dual amplifier pin out allows the AD642 to
replace lower performance duals without redesign.
6. The AD642 is available in chip form.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD642–SPECIFICATIONS (@ + 25°C, and V = ±15 V dc)
S
AD642J
Typ
Model
Min
OPEN LOOP GAIN
VO = ± 10 V, RL ≥ 2 kΩ
TMIN to TMAX, RL = 2 kΩ
100,000
100,000
OUTPUT CHARACTERISTICS
Voltage @ RL = 2 kΩ, TMIN to TMAX
Voltage @ RL = 10 kΩ, TMIN to TMAX
Short Circuit Current
± 10
± 12
± 12
± 13
25
1.0
50
3.0
2.0
2.0
INPUT OFFSET VOLTAGE1
Initial Offset
Input Offset Voltage TMIN to TMAX
Input Offset Voltage vs. Supply,
TMIN to TMAX
INPUT BIAS CURRENT
Either Input
Offset Current
Min
AD642K
Typ
Max
250,000
250,000
± 10
± 12
FREQUENCY RESPONSE
Unity Gain Small Signal
Full Power Response
Slew Rate, Unity Gain
Max
AD642L
Typ
Max
Min
250,000
250,000
± 10
± 12
± 12
± 13
25
1.0
50
3.0
2.0
Min
AD642S
Typ
Max
V/V
V/V
250,000
100,000
± 10
± 12
± 12
± 13
25
1.0
50
3.0
2.0
Unit
± 12
± 13
25
V
V
mA
1.0
50
3.0
MHz
kHz
V/µs
2.0
3.5
1.0
2.0
0.5
1.0
1.0
3.5
mV
mV
200
100
100
100
µV/V
35
pA
0.5
3.5
35
2
10
5
75
10
2
35
10
2
35
10
2
MATCHING CHARACTERISTICS 3
Input Offset Voltage
Input Offset Voltage TMIN to TMAX
Input Bias Current
Crosstalk
–124
–124
–124
–124
mV
mV
pA
dB
INPUT IMPEDANCE
Differential
Common Mode
1012i6
1012i6
1012i6
1012i6
1012i6
1012i6
1012i6
1012i6
MΩipF
MΩipF
± 20
± 12
V
V
dB
2
70
45
30
25
µV p-p
nV/√Hz
nV/√Hz
nV/√Hz
nV/√Hz
1.0
3.5
35
INPUT VOLTAGE RANGE
Differential4
Common Mode
Common-Mode Rejection
± 20
± 12
± 10
0.5
2.0
25
± 10
76
± 10
80
INPUT NOISE
Voltage 0.1 Hz to 10 Hz
f = 10 Hz
f = 100 Hz
f = 1 kHz
f = 10 kHz
2
70
45
30
25
POWER SUPPLY
Rated Performance
Operating
Quiescent Current
± 20
± 12
± 18
2.8
±5
± 20
± 12
± 10
80
2
70
45
30
25
± 15
±5
0.25
1.0
25
± 15
80
2
70
45
30
25
± 15
2.8
±5
± 15
± 15
2.8
±5
± 15
± 15
2.8
TRANSISTOR COUNT
58
58
58
58
PACKAGE OPTION
TO-99 Style (H-08B)
AD642JH
AD642KH
AD642LH
AD642SH
V
V
mA
NOTES
1
Input Offset Voltage specifications are guaranteed after 5 minutes of operation at T A = +25°C.
2
Bias Current specifications are guaranteed at maximum at either input after 5 minutes of operation at T A = +25°C. For higher temperatures, the current doublers
every 10°C.
3
Matching is defined as ther difference between parameters of the two amplifiers.
4
Defined as the maximum safe voltage between inputs, such that neither exceeds ± 10 V from ground.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
OUTLINE DIMENSIONS
METALIZATION PHOTOGRAPHIC
Dimensions shown in inches and (mm).
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
TO-99
REFERENCE PLANE
0.185 (4.70)
0.165 (4.19)
0.050
(1.27)
MAX
0.750 (19.05)
0.500 (12.70)
0.250 (6.35)
MIN
0.100
(2.54)
BSC
0.160 (4.06)
0.110 (2.79)
5
6
4
0.335 (8.51)
0.305 (7.75)
0.200
(5.08)
BSC
0.370 (9.40)
0.335 (8.51)
7
3
8
2
0.040 (1.02) MAX
0.045 (1.14)
0.010 (0.25)
0.019 (0.48)
0.016 (0.41)
0.100
(2.54)
BSC
0.021 (0.53)
0.016 (0.41)
BASE & SEATING PLANE
0.045 (1.14)
0.027 (0.69)
1
0.034 (0.86)
0.027 (0.69)
45°
BSC
–2–
REV. 0
Typical Characteristics–AD642
AD642
Figure 1. Input Voltage Range
vs. Supply Voltage
Figure 4. Quiescent Current vs.
Supply Voltage
Figure 7. Input Bias Current
vs. CMV
Figure 10. Open Loop
Frequency Response
REV. 0
Figure 2. Output Voltage Swing vs.
Supply Voltage
Figure 3. Output Voltage Swing
vs. Load Resistance
Figure 5. Input Bias Current
vs. Power Supply Voltage
Figure 6. Input Bias Current
vs. Temperature
Figure 8. Change in Offset
vs. Warm-Up Time
Figure 11. Open Loop Voltage
Gain vs. Supply Voltage
–3–
Figure 9. Open Loop vs.
Temperature
Figure 12. Power Supply Rejection
vs. Frequency
AD642
Figure 13. Common-Mode Rejection
Ratio vs. Frequency
Figure 14. Large Signal Frequency
Response
Figure 16. Total Harmonic Distortion
vs. Frequency
Figure 17. Input Noise Voltage
Spectral Density
a. Unity Gain Follower
b. Follower with Gain = 10
Figure 19. T. H. D. Test Circuits
5V
2µs
Figure 21a. Unity Gain Follower
Pulse Response (Large Signal)
50mV
Figure 18. Total Noise vs. Source
Impedance
Figure 20. Crosstalk Test Circuit
1µs
Figure 21b. Unity Gain Follower Pulse
Response (Small Signal)
5V
Figure 22a. Unity Gain Inverter
Figure 15. Output Swing and Error vs.
Output Settling Time (Circuit of
Figure 23)
2µs
Figure 22b. Unity Gain Inverter
Pulse Response (Large Signal)
–4–
Figure 21c. Unity Gain Follower
50mV
1µs
Figure 22c. Unity Gain Inverter
Pulse Response (Small Signal)
REV. 0
AD642
Figure 23. Settling Time Test Circuit
Fast settling time (8 µs to 0.01% for 20 V p-p step), low power
and low offset voltage make the AD642 an excellent choice for
use as an output amplifier for current output D/A converters
such as the AD7541.
1mV
10V
Figure 26. Precision FET Input Instrumentation Amplifier
5µs
The output impedance of a CMOS DAC varies with the digital
word thus changing the noise of the amplifier circuit. This effect
will cause a nonlinearity whose magnitude is dependent on the
offset voltage of the amplifier. The AD642K with trimmed
offset will minimize the effect. The Schottky protection diodes
recommended for use with many older CMOS DACs are not
required when using the AD642.
VERROR 1mV/DIV
INPUT 10V/DIV
Figure 24. Settling Characteristic Detail
The upper trace of the oscilloscope photograph of Figure 24
shows the settling characteristic of the AD642. The lower trace
represents the input to Figure 23. The AD642 has been
designed for fast settling to 0.01%, however, feedback components, circuit layout and circuit design must be carefully
considered to obtain optimum settling time.
Figure 27a. AD642 Used as DAC Output Amplifier
Figure 27a illustrates the AD7541 12-bit digital-to-analog
converter, connected for bipolar operation. Since the digital
input can accept bipolar numbers and VREF can accept a
bipolar analog input, the circuit can perform a 4-quadrant
multiplication.
Figure 25. 0.1 Hz to 10 Hz 2nd Order Bandpass Filter,
Maximally Flat
The low frequency (1/f) noise has a power spectrum that is
inversely proportional to frequency. Typically this noise is not
important above 10 Hz, but it can be important for low frequency-high gain applications.
10V
5µs
1 0 V /D IV V E R T ,
5 µ s /D IV H O R IZ .
The low noise characteristic of the AD642 make it ideal for 1/f
noise testing circuits. The circuit of Figure 25 is a 0.1 Hz to
10 Hz bandpass filter with second order filter characteristics.
V OUT
5 V /D IV V E R T ,
5 µ s /D IV H O R IZ .
The circuit illustrated in Figure 26 uses two AD642s to
construct an instrumentation amplifier with low input current
(35 pA max), high linearity and low offset voltage and offset
voltage drift. The AD644 may be substituted for increased
speed, but the higher open-loop gain of the AD642 maintains
better linearity over the gain range of 1 to 1000. Amplifier A1 is
an AD642L for low input offset voltage (250 µV max) and low
input offset voltage drift at high gains because matching and
tracking are very important for the balanced input stage.
Amplifier A2 serves two nonrelated functions, output amplifier
and active data-guard drive, and does not require close matching between sections; thus it may be an AD642J.
REV. 0
5V
V REF IN , 2 0 V p -p , 3 3 k H z
S E T T L IN G T IM E : 1 0 µ s T O
0 .0 1 % O N 2 0 V S T E P
Figure 27b. Voltage Output DAC Settling Characteristic
The photo above shows the output of the circuit Figure 27a.
The upper trace represents the reference input, and the bottom
trace shows the output voltage for a digital input of all ones on
the DAC. The 47 pF capacitor across the feedback resistor
compensates for the DAC output capacitance, and the 150 pF
load capacitor serves to minimize output glitches.
Log amplifiers or log ratio amplifiers are useful in applications requiring compression of wide-range analog input data,
–5–
AD642
AD642
The low input bias current (35 pA) and low noise characteristics
of the AD642 make it suitable for electrometer applications
such as photo diode preamplifiers and picoampere current-tovoltage converters. The use of guarding techniques in printed
circuit board layout and construction is critical in printed circuit
board layout and construction is critical for achieving the
ultimate in low leakage performance that the AD642 can
deliver. The input guarding scheme shown in Figure 29 will
minimize leakage as much as possible; the guard ring should be
applied to both sides of the board. The guard ring is connected
to a low impedance potential at the same level as the inputs.
High impedance signal lines should not be extended for any
unnecessary length on a printed circuit; to minimize noise and
leakage, they must be carried in rigid shielded cables.
The picoamp level input current and low offset voltage of the
AD642 make it suitable for wide dynamic range log amplifiers.
Figure 28 is a schematic of a log ratio circuit employing the
AD642 that can achieve less than 1% conformance error over 5
decades of current input, 1 nA to 100 µA. For voltage inputs,
the dynamic range is typically 50 mV to 10 V for 1% error
limited on the low end by the amplifier’s input offset voltage.
C632c–5–12/86
V2 = –10.00 V and adjust “Balance” for VOUT = 0.00 V. Next
apply V1 = –10.00 V, V2 = –1.00 V and adjust gain for VOUT =
+1.00 V. Repeat this procedure until gain and balance readings
are within 2 mV of ideal values.
linearization of transducers having exponential outputs, and
analog computing, ranging from simple translation of natural
relationships in log form (e.g., computing absorbance as the logratio of input currents), to the use of logarithms in facilitating
analog computation of terms involving arbitrary exponents and
multiterm products and ratios.
Figure 29. Board Layout for Guarding Inputs
INPUT PROTECTION
Figure 28. Log-Ratio Amplifier
The conversion between current (or voltage) input and log
output is accomplished by the base emitter junctions of the dual
transistor Q1. Assuming Q1 has β>100, which is the case for the
specified transistor, the base-emitter voltage on side 1 is to a
close approximation:
V BE A = kT /q ln I1/I S1
Many instrumentation situations, such as flame detectors in gas
chromatographs, involve measurement of low level currents
from high-voltage sources. In such applications, a sensor fault
condition may apply a very high potential to the input of the
current-to-voltage converting amplifier. This possibility necessitates some form of input protection. Many electrometer type
devices, especially CMOS designs, can require elaborate Zener
protection schemes which often compromise overall performance. The AD642 requires input protection only if the source
is not current limited, and as such is similar to many JFETinput designs. The failure mode would be overheating from
excess current rather than voltage breakdown. If the source is
not current-limited, all that is required is a resistor in series with
the affected input terminal so that the maximum overload
current is 1.0 mA (for example, 100 kΩ for a 100 volt overload).
This simple scheme will cause no significant reduction in
performance and give complete overload protection. Figure 30
shows proper connections.
This circuit is arranged to take the difference of the VBE’s of
Q1A and Q1B, thus producing an output voltage proportional
to the log of the ratio of the inputs:
V OUT = – K (V BE A – V BE B ) = –
KkT
(ln I1/I S1 – ln I 2 /I S2 )
q
V OUT = – K kT /q ln I1/I 2
The scaling constant, K is set by R1 and RTC to about 16, to
produce 1 V change in output voltage per decade difference in
input signals. RTC is a special resistor with a +3500 ppm/°C
temperature coefficient, which makes K inversely proportional
to temperature, compensating for the “T” in kT/q. The log-ratio
transfer characteristic is therefore independent of temperature.
This particular log ratio circuit is free from the dynamic problems that plague many other log circuits. The –3 dB bandwidth
is 50 kHz over the top 3 decades, 100 nA to 100 µA, and
decreases smoothly at lower input levels. This circuit needs no
additional frequency compensation for stable operation from
input current sources, such as photodiodes, that may have
100 pF of shunt capacitance. For larger input capacitances a
20 pF integration capacitor around each amplifier will provide a
smoother frequency response.
The log ratio amplifier can be readily adjusted for optimum
accuracy by following this simple procedure. First, apply V1 =
Figure 30. AD642 Input Protection
–6–
REV. 0
PRINTED IN U.S.A.
The AD642 is guaranteed for a maximum safe input potential
equal to the power supply potential. The input stage design also
allows differential input voltages of up to ± 0.5 volts while
maintaining the full differential input resistance of 1012 Ω. This
makes the AD642 suitable for low speed voltage comparators
directly connected to a high impedance source.
Similar pages