AD AD9609-40EBZ 10-bit, 20 msps/40 msps/65 msps/80 msps, 1.8 v analog-to-digital converter Datasheet

10-Bit, 20 MSPS/40 MSPS/65 MSPS/80 MSPS,
1.8 V Analog-to-Digital Converter
AD9609
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
1.8 V analog supply operation
1.8 V to 3.3 V output supply
SNR
61.5 dBFS at 9.7 MHz input
61.0 dBFS at 200 MHz input
SFDR
75 dBc at 9.7 MHz input
73 dBc at 200 MHz input
Low power
45 mW at 20 MSPS
76 mW at 80 MSPS
Differential input with 700 MHz bandwidth
On-chip voltage reference and sample-and-hold circuit
2 V p-p differential analog input
DNL = ±0.10 LSB
Serial port control options
Offset binary, gray code, or twos complement data format
Optional clock duty cycle stabilizer
Integer 1-to-8 input clock divider
Built-in selectable digital test pattern generation
Energy-saving power-down modes
Data clock out with programmable clock and data alignment
AVDD
APPLICATIONS
Communications
Diversity radio systems
Multimode digital receivers
GSM, EDGE, W-CDMA, LTE, CDMA2000, WiMAX, TD-SCDMA
Smart antenna systems
Battery-powered instruments
Handheld scope meters
Portable medical imaging
Ultrasound
Radar/LIDAR
PET/SPECT imaging
Rev. B
GND
DRVDD
SDIO SCLK CSB
RBIAS
SPI
PROGRAMMING DATA
VIN+
ADC
CORE
VIN–
CMOS
OUTPUT BUFFER
VCM
VREF
OR
D9 (MSB)
D0 (LSB)
DCO
SENSE
AD9609
DIVIDE
BY
1 TO 8
DCS
CLK+ CLK–
MODE
CONTROLS
PDWN
DFS
MODE
08541-001
REF
SELECT
Figure 1.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
The AD9609 operates from a single 1.8 V analog power
supply and features a separate digital output driver supply
to accommodate 1.8 V to 3.3 V logic families.
The sample-and-hold circuit maintains excellent performance
for input frequencies up to 200 MHz and is designed for low
cost, low power, and ease of use.
A standard serial port interface supports various product
features and functions, such as data output formatting,
internal clock divider, power-down, DCO and data output
(D9 to D0) timing and offset adjustments, and voltage
reference modes.
The AD9609 is packaged in a 32-lead RoHS compliant
LFCSP that is pin compatible with the AD9629 12-bit ADC
and the AD9649 14-bit ADC, enabling a simple migration
path between 10-bit and 14-bit converters sampling from
20 MSPS to 80 MSPS.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9609* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
TOOLS AND SIMULATIONS
View a parametric search of comparable parts.
• Visual Analog
• AD9609 IBIS Model
EVALUATION KITS
• AD9609 Evaluation Board
REFERENCE MATERIALS
Technical Articles
DOCUMENTATION
Application Notes
• Improve The Design Of Your Passive Wideband ADC
Front-End Network
• AN-1142: Techniques for High Speed ADC PCB Layout
• MS-2210: Designing Power Supplies for High Speed ADC
• AN-586: LVDS Outputs for High Speed A/D Converters
• AN-742: Frequency Domain Response of SwitchedCapacitor ADCs
DESIGN RESOURCES
• AD9609 Material Declaration
• AN-807: Multicarrier WCDMA Feasibility
• PCN-PDN Information
• AN-808: Multicarrier CDMA2000 Feasibility
• Quality And Reliability
• AN-812: MicroController-Based Serial Port Interface (SPI)
Boot Circuit
• Symbols and Footprints
• AN-827: A Resonant Approach to Interfacing Amplifiers to
Switched-Capacitor ADCs
DISCUSSIONS
View all AD9609 EngineerZone Discussions.
• AN-878: High Speed ADC SPI Control Software
• AN-935: Designing an ADC Transformer-Coupled Front
End
Data Sheet
• AD9609: 10-Bit, 20 MSPS/40 MSPS/65 MSPS/80 MSPS, 1.8
V Analog-to-Digital Converter Data Sheet
User Guides
• Evaluating the AD9266/AD9649/AD9629/AD9609 Analogto-Digital Converters
SAMPLE AND BUY
Visit the product page to see pricing options.
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD9609
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Voltage Reference ....................................................................... 19
Applications ....................................................................................... 1
Clock Input Considerations ...................................................... 20
Functional Block Diagram .............................................................. 1
Power Dissipation and Standby Mode .................................... 22
Product Highlights ........................................................................... 1
Digital Outputs ........................................................................... 22
Revision History ............................................................................... 2
Timing.......................................................................................... 23
General Description ......................................................................... 3
Built-In Self-Test (BIST) and Output Test .................................. 24
Specifications..................................................................................... 4
Built-In Self-Test (BIST) ............................................................ 24
DC Specifications ......................................................................... 4
Output Test Modes ..................................................................... 24
AC Specifications.......................................................................... 5
Serial Port Interface (SPI) .............................................................. 25
Digital Specifications ................................................................... 6
Configuration Using the SPI ..................................................... 25
Switching Specifications .............................................................. 7
Hardware Interface ..................................................................... 26
Timing Specifications .................................................................. 8
Configuration Without the SPI ................................................ 26
Absolute Maximum Ratings ............................................................ 9
SPI Accessible Features .............................................................. 26
Thermal Characteristics .............................................................. 9
Memory Map .................................................................................. 27
ESD Caution .................................................................................. 9
Reading the Memory Map Register Table............................... 27
Pin Configuration and Function Descriptions ........................... 10
Open Locations .......................................................................... 27
Typical Performance Characteristics ........................................... 11
Default Values ............................................................................. 27
AD9609-80 .................................................................................. 11
Memory Map Register Table ..................................................... 28
AD9609-65 .................................................................................. 13
Memory Map Register Descriptions ........................................ 30
AD9609-40 .................................................................................. 14
Applications Information .............................................................. 31
AD9609-20 .................................................................................. 15
Design Guidelines ...................................................................... 31
Equivalent Circuits ......................................................................... 16
Outline Dimensions ....................................................................... 32
Theory of Operation ...................................................................... 17
Ordering Guide .......................................................................... 32
Analog Input Considerations.................................................... 17
REVISION HISTORY
2/2017—Rev. A to Rev. B
Added Endnote 1, Table 17 ........................................................... 28
Changes to Power and Ground Recommendations Section ..... 31
Added Soft Reset Section............................................................... 31
6/2015—Rev. 0 to Rev. A
Change to Product Highlights Section .......................................... 1
Changes to Figure 3 and Table 8 ................................................... 10
Updated Outline Dimensions ....................................................... 32
Changes to Ordering Guide .......................................................... 32
10/2009—Revision 0: Initial Version
Rev. B | Page 2 of 32
Data Sheet
AD9609
GENERAL DESCRIPTION
The AD9609 is a monolithic, single channel 1.8 V supply, 10-bit,
20/40/65/80 MSPS analog-to-digital converter (ADC). It features
a high performance sample-and-hold circuit and on-chip voltage
reference.
A differential clock input with selectable internal 1 to 8 divide ratio
controls all internal conversion cycles. An optional duty cycle
stabilizer (DCS) compensates for wide variations in the clock duty
cycle while maintaining excellent overall ADC performance.
The product uses multistage differential pipeline architecture
with output error correction logic to provide 10-bit accuracy at
80 MSPS data rates and to guarantee no missing codes over the
full operating temperature range.
The digital output data is presented in offset binary, gray code, or
twos complement format. A data output clock (DCO) is provided
to ensure proper latch timing with receiving logic. Both 1.8 V and
3.3 V CMOS levels are supported.
The ADC contains several features designed to maximize flexibility
and minimize system cost, such as programmable clock and data
alignment and programmable digital test pattern generation. The
available digital test patterns include built-in deterministic and
pseudorandom patterns, along with custom user-defined test
patterns entered via the serial port interface (SPI).
The AD9609 is available in a 32-lead RoHS-compliant LFCSP
and is specified over the industrial temperature range (−40°C
to +85°C).
Rev. B | Page 3 of 32
AD9609
Data Sheet
SPECIFICATIONS
DC SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error 1
Differential Nonlinearity (DNL) 2
Integral Nonlinearity (INL)2
TEMPERATURE DRIFT
Offset Error
INTERNAL VOLTAGE REFERENCE
Output Voltage (1 V Mode)
Load Regulation Error at 1.0 mA
INPUT-REFERRED NOISE
VREF = 1.0 V
ANALOG INPUT
Input Span, VREF = 1.0 V
Input Capacitance 3
Input Common-Mode Voltage
Input Common-Mode Range
REFERENCE INPUT RESISTANCE
POWER SUPPLIES
Supply Voltage
AVDD
DRVDD
Supply Current
IAVDD2
IDRVDD2 (1.8 V)
IDRVDD2 (3.3 V)
POWER CONSUMPTION
DC Input
Sine Wave Input2 (DRVDD = 1.8 V)
Sine Wave Input2 (DRVDD = 3.3 V)
Standby Power 4
Power-Down Power
Temp
Full
Full
Full
Full
Full
25°C
Full
25°C
Min
10
−0.45
Full
Full
Full
AD9609-20/AD9609-40
Typ
Max
Guaranteed
+0.05
+0.55
−1.5
±0.15/±0.25
±0.05/±0.08
±0.35
±0.15
Min
10
Guaranteed
−0.45 +0.05 +0.55
−1.5
±0.25
±0.15
±0.45
±0.15
±2
0.984
AD9609-65
Typ
Max
Min
10
AD9609-80
Typ
Max
Guaranteed
−0.45 +0.05 +0.55
−1.5
±0.25
±0.07
±0.45
±0.15
±2
0.996
2
1.008
0.984
0.996
2
±2
1.008
0.984
0.996
2
Unit
Bits
% FSR
% FSR
LSB
LSB
LSB
LSB
ppm/°C
1.008
V
mV
25°C
0.06
0.08
0.08
LSB rms
Full
Full
Full
Full
Full
2
6
0.9
2
6
0.9
2
6
0.9
V p-p
pF
V
V
kΩ
Full
Full
0.5
1.3
0.5
7.5
1.7
1.7
1.3
0.5
7.5
1.8
1.9
3.6
Full
Full
Full
24.9/29.7
1.4/2.2
2.5/4.1
27.0/32.0
Full
Full
Full
Full
Full
45.2/54.7
46.3/57.4
53.1/67.0
34
0.5
52.0/61.0
1.7
1.7
1.8
1.9
3.6
37.1
3.6
6.6
39.5
67.7
73.3
88.6
34
0.5
1.7
1.7
78.0
Measured with 1.0 V external reference.
Measured with a 10 MHz input frequency at rated sample rate, full-scale sine wave, with approximately 5 pF loading on each output bit.
Input capacitance refers to the effective capacitance between one differential input pin and AGND.
4
Standby power is measured with a dc input and the CLK active.
1
2
3
Rev. B | Page 4 of 32
1.3
7.5
1.8
1.9
3.6
V
V
41.8
4.3
7.9
45
mA
mA
mA
76.3
83.0
89.5
34
0.5
92
mW
mW
mW
mW
mW
Data Sheet
AD9609
AC SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
Table 2.
Parameter 1
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
SIGNAL-TO-NOISE-AND-DISTORTION (SINAD)
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
WORST SECOND OR THIRD HARMONIC
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
WORST OTHER (HARMONIC OR SPUR)
fIN = 9.7 MHz
fIN = 30.5 MHz
fIN = 70 MHz
fIN = 200 MHz
TWO-TONE SFDR
fIN = 30.5 MHz (−7 dBFS), 32.5 MHz (−7 dBFS)
ANALOG INPUT BANDWIDTH
1
Temp
25°C
25°C
Full
25°C
Full
25°C
25°C
25°C
Full
25°C
Full
25°C
AD9609-20/AD9609-40
Min
Typ
Max
Min
61.7
61.7
AD9609-65
Typ
Max
AD9609-80
Min Typ
Max
61.5
61.5
61.2
61.5
61.5
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
61.0
61.6
61.5
61.5
61.0
61.6
61.5
60.7/60.9
61.0
61.0
61.4
61.3
61.4
61.4
60
60
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
60.5
61.5
Unit
61.4
61.4
60.5
25°C
25°C
25°C
25°C
9.9
9.9
9.9
9.9
9.9
9.9
9.6
9.9
9.9
9.9
9.6
Bits
Bits
Bits
Bits
25°C
25°C
Full
25°C
Full
25°C
−81
−80
−78
−80
−78
−80
dBc
dBc
dBc
dBc
dBc
dBc
25°C
25°C
Full
25°C
Full
25°C
78
80.5
25°C
25°C
Full
25°C
Full
25°C
25°C
25°C
−67
−65.5
−82
−78
−78
−73
−73
75
75
75
75
−68
67
dBc
dBc
dBc
dBc
dBc
dBc
65.5
78
75
75
68
−82
−82
73
73
−80
−80
−80
−80
−80
−80
−80
−80
dBc
dBc
dBc
dBc
dBc
dBc
78
700
78
700
dBc
MHz
−74
−82
−72
−73
700
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
Rev. B | Page 5 of 32
AD9609
Data Sheet
DIGITAL SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
Table 3.
Parameter
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Internal Common-Mode Bias
Differential Input Voltage
Input Voltage Range
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
LOGIC INPUTS (SCLK/DFS, MODE, SDIO/PDWN) 1
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
LOGIC INPUTS (CSB) 2
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Input Capacitance
DIGITAL OUTPUTS
DRVDD = 3.3 V
High Level Output Voltage, IOH = 50 µA
High Level Output Voltage, IOH = 0.5 mA
Low Level Output Voltage, IOL = 1.6 mA
Low Level Output Voltage, IOL = 50 µA
DRVDD = 1.8 V
High Level Output Voltage, IOH = 50 µA
High Level Output Voltage, IOH = 0.5 mA
Low Level Output Voltage, IOL = 1.6 mA
Low Level Output Voltage, IOL = 50 µA
1
2
Temp
Full
Full
Full
Full
Full
Full
Full
Min
AD9609-20/AD9609-40/AD9609-65/AD9609-80
Typ
Max
CMOS/LVDS/LVPECL
0.9
0.2
GND − 0.3
−10
−10
8
Full
Full
Full
Full
Full
Full
1.2
0
−50
−10
Full
Full
Full
Full
Full
Full
1.2
0
−10
40
Full
Full
Full
Full
3.29
3.25
Full
Full
Full
Full
1.79
1.75
10
4
3.6
AVDD + 0.2
+10
+10
12
V
V
µA
µA
kΩ
pF
DRVDD + 0.3
0.8
+10
135
V
V
µA
µA
kΩ
pF
26
2
Rev. B | Page 6 of 32
V
V p-p
V
µA
µA
kΩ
pF
DRVDD + 0.3
0.8
−75
+10
30
2
Internal 30 kΩ pull-down.
Internal 30 kΩ pull-up.
Unit
0.2
0.05
V
V
V
V
0.2
0.05
V
V
V
V
Data Sheet
AD9609
SWITCHING SPECIFICATIONS
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
Table 4.
Parameter
CLOCK INPUT PARAMETERS
Input Clock Rate
Conversion Rate 1
CLK Period—Divide-by-1 Mode (tCLK)
CLK Pulse Width High (tCH)
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tJ)
DATA OUTPUT PARAMETERS
Data Propagation Delay (tPD)
DCO Propagation Delay (tDCO)
DCO to Data Skew (tSKEW)
Pipeline Delay (Latency)
Wake-Up Time 2
Standby
OUT-OF-RANGE RECOVERY TIME
2
Full
Full
Full
AD9609-20/AD9609-40
Min
Typ
Max
625
20/40
Min
AD9609-65
Typ
Max
AD9609-80
Typ
Max
Full
Full
25.0/12.5
1.0
0.1
7.69
1.0
0.1
6.25
1.0
0.1
Full
Full
Full
Full
Full
Full
Full
3
3
0.1
8
350
600/400
2
3
3
0.1
8
350
300
2
3
3
0.1
8
350
260
2
ns
ns
ns
Cycles
µs
ns
Cycles
50/25
3
15.38
625
80
Unit
MHz
MSPS
ns
ns
ns
ps rms
3
625
65
Min
3
12.5
Conversion rate is the clock rate after the CLK divider.
Wake-up time is dependent on the value of the decoupling capacitors.
N–1
N+4
tA
N+5
N
N+3
VIN
N+1
tCH
N+2
tCLK
CLK+
CLK–
tDCO
DCO
tSKEW
DATA
N–8
N–7
N–6
tPD
Figure 2. CMOS Output Data Timing
Rev. B | Page 7 of 32
N–5
N–4
08541-002
1
Temp
AD9609
Data Sheet
TIMING SPECIFICATIONS
Table 5.
Parameter
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
tH
tHIGH
tLOW
tEN_SDIO
tDIS_SDIO
Conditions
Min
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
Setup time between CSB and SCLK
Hold time between CSB and SCLK
SCLK pulse width high
SCLK pulse width low
Time required for the SDIO pin to switch from an input to an
output relative to the SCLK falling edge
Time required for the SDIO pin to switch from an output to an
input relative to the SCLK rising edge
2
2
40
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
10
ns
Rev. B | Page 8 of 32
Typ
Max
Unit
Data Sheet
AD9609
ABSOLUTE MAXIMUM RATINGS
THERMAL CHARACTERISTICS
Table 6.
Parameter
AVDD to AGND
DRVDD to AGND
VIN+, VIN− to AGND
CLK+, CLK− to AGND
VREF to AGND
SENSE to AGND
VCM to AGND
RBIAS to AGND
CSB to AGND
SCLK/DFS to AGND
SDIO/PDWN to AGND
MODE/OR to AGND
D0 through D9 to AGND
DCO to AGND
Operating Temperature Range (Ambient)
Maximum Junction Temperature Under Bias
Storage Temperature Range (Ambient)
Rating
−0.3 V to +2.0 V
−0.3 V to +3.9 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to AVDD + 0.2 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−40°C to +85°C
150°C
−65°C to +150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
The exposed paddle is the only ground connection for the chip.
The exposed paddle must be soldered to the AGND plane of the
user’s circuit board. Soldering the exposed paddle to the user’s
board also increases the reliability of the solder joints and
maximizes the thermal capability of the package.
Table 7. Thermal Resistance
Package
Type
32-Lead LFCSP
5 mm × 5 mm
Airflow
Velocity
(m/sec)
0
1.0
2.5
θJA1, 2
37.1
32.4
29.1
θJC1, 3
3.1
θJB1, 4
20.7
ΨJT1,2
0.3
0.5
0.8
Unit
°C/W
°C/W
°C/W
Per JEDEC 51-7, plus JEDEC 51-5 2S2P test board.
Per JEDEC JESD51-2 (still air) or JEDEC JESD51-6 (moving air).
Per MIL-Std 883, Method 1012.1.
4
Per JEDEC JESD51-8 (still air).
1
2
3
Typical θJA is specified for a 4-layer PCB with a solid ground
plane. As shown in Table 7, airflow improves heat dissipation,
which reduces θJA. In addition, metal in direct contact with the
package leads from metal traces, through holes, ground, and
power planes, reduces the θJA.
ESD CAUTION
Rev. B | Page 9 of 32
AD9609
Data Sheet
32
31
30
29
28
27
26
25
AVDD
VIN+
VIN–
AVDD
RBIAS
VCM
SENSE
VREF
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD9609
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
AVDD
MODE/OR
DCO
D9 (MSB)
D8
D7
D6
D5
08541-003
1
2
3
4
5
6
7
8
NIC 9
NIC 10
(LSB) D0 11
D1 12
DRVDD 13
D2 14
D3 15
D4 16
CLK+
CLK–
AVDD
CSB
SCLK/DFS
SDIO/PDWN
NIC
NIC
NOTES
1. NIC = NO INTERNAL CONNECTION.
2. EXPOSED PADDLE. THE EXPOSED PADDLE IS THE ONLY GROUND CONNECTION.
IT MUST BE SOLDERED TO THE ANALOG GROUND OF THE PCB
TO ENSURE PROPER FUNCTIONALITY AND HEAT DISSIPATION,
NOISE, AND MECHANICAL STRENGTH BENEFITS.
Figure 3. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
0
Mnemonic
EPAD
1, 2
3, 24, 29, 32
4
5
CLK+, CLK−
AVDD
CSB
SCLK/DFS
6
SDIO/PDWN
7 to 10
11 to 12, 14 to 21
13
22
23
NIC
D0 (LSB) to
D9 (MSB)
DRVDD
DCO
MODE/OR
25
26
27
28
30, 31
VREF
SENSE
VCM
RBIAS
VIN−, VIN+
Description
Exposed Paddle. The exposed paddle is the only ground connection. It must be soldered to the analog
ground of the PCB to ensure proper functionality and heat dissipation, noise, and mechanical strength
benefits.
Differential Encode Clock for PECL, LVDS, or 1.8 V CMOS Inputs.
1.8 V Supply Pin for ADC Core Domain.
SPI Chip Select. Active low enable, 30 kΩ internal pull-up.
SPI Clock Input in SPI Mode (SCLK). 30 kΩ internal pull-down.
Data Format Select in Non-SPI Mode (DFS). Static control of data output format. 30 kΩ internal pull-down.
DFS high = twos complement output; DFS low = offset binary output.
SPI Data Input/Output (SDIO). Bidirectional SPI data I/O with 30 kΩ internal pull-down.
Non-SPI Mode Power-Down (PDWN). Static control of chip power-down with 30 kΩ internal pulldown. See Table 15 for details.
No Internal Connection.
ADC Digital Outputs.
1.8 V to 3.3 V Supply Pin for Output Driver Domain.
Data Clock Digital Output.
Chip Mode Select Input (MODE)/Out-of-Range Digital Output in SPI Mode (OR).
Default = out-of-range (OR) digital output (SPI Register 0x2A, Bit 0 = 1).
Option = chip mode select input (SPI Register 0x2A, Bit 0 = 0).
Chip power-down (SPI Register 0x08, Bits[7:5] = 100b).
Chip stand-by (SPI Register 0x08, Bits[7:5] = 101b).
Normal operation, output disabled (SPI Register 0x08, Bits[7:5] = 110b).
Normal operation, output enabled (SPI Register 0x08, Bits[7:5] = 111b).
Out-of-range (OR) digital output only in non-SPI mode.
1.0 V Voltage Reference Input/Output. See Table 10.
Reference Mode Selection. See Table 10.
Analog Output Voltage at Mid AVDD Supply. Sets common mode of the analog inputs.
Set Analog Current Bias. Connect to 10 kΩ (1% tolerance) resistor to ground.
ADC Analog Inputs.
Rev. B | Page 10 of 32
Data Sheet
AD9609
TYPICAL PERFORMANCE CHARACTERISTICS
AD9609-80
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
0
0
80MSPS
9.7MHz @ –1dBFS
SNR = 60.5dB (61.5dBFS)
SFDR = 80.3dBc
–20
–40
AMPLITUDE (dB)
–60
–80
–100
–60
–80
5
10
15
20
25
FREQUENCY (MHz)
30
35
40
–120
08541-033
0
0
Figure 4. AD9609-80 Single-Tone FFT with fIN = 9.7 MHz
5
10
15
20
25
FREQUENCY (MHz)
30
35
40
08541-034
–100
–120
Figure 7. AD9609-80 Single-Tone FFT with fIN = 30.5 MHz
0
0
80MSPS
70.3MHz @ –1dBFS
SNR = 60.4dB (61.4dBFS)
SFDR = 82.2dBc
80MSPS
200MHz @ –1dBFS
SNR = 60.1dB (60.1dBFS)
SFDR = 74.176dBc
–20
AMPLITUDE (dBFS)
–20
AMPLITUDE (dBFS)
–40
–40
–60
–80
–40
–60
–80 2
3
+
46
–100
5
–100
0
5
10
15
20
25
FREQUENCY (MHz)
30
35
40
–120
08541-062
–120
0
Figure 5. AD9609-80 Single-Tone FFT with fIN = 70.3 MHz
5
10
15
20
25
FREQUENCY (MHz)
30
35
40
08541-134
AMPLITUDE (dB)
–20
80MSPS
30.5MHz @ –1dBFS
SNR = 60.5dB (61.5dBFS)
SFDR = 83.5dBc
Figure 8. AD9609-80 Single-Tone FFT with fIN = 200 MHz
0
80MSPS
30.5MHz @ –7dBFS
32.5MHz @ –7dBFS
SFDR = 78dBc
AMPLITUDE (dB)
–30
–10
SFDR/IMD3 (dBFS/dBc)
–15
–45
–60
F1 + F2
–75
2F1 – F2
2F2 + F1
F2 – F1
2F1 – F2
–30
–50
SFDR (dBc)
IMD3 (dBc)
–70
SFDR (dBFS)
–90
–90
–105
0
4
8
12
16
20
24
28
FREQUENCY (MHz)
32
36
40
–110
–60
08541-036
–120
Figure 6. AD9609-80 Two-Tone FFT with fIN1 = 30.5 MHz and fIN2 = 32.5 MHz
–54
–48
–42
–36
–30
–24
–18
INPUT AMPLITUDE (dBFS)
–12
–6
08541-054
IMD3 (dBFS)
Figure 9. Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with fIN1 = 30.5 MHz
and fIN2 = 32.5 MHz
Rev. B | Page 11 of 32
AD9609
Data Sheet
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
85
0.20
0.16
SFDR (dBc)
0.12
75
DNL ERROR (LSB)
SNR/SFDR (dBFS/dBc)
80
70
65
SNR (dBFS)
60
0.08
0.04
0
–0.04
–0.08
–0.12
55
0
50
100
150
AIN FREQUENCY (MHz)
200
–0.20
08541-057
50
24
Figure 10. AD9609-80 SNR/SFDR vs. Input Frequency (AIN) with 2 V p-p Full Scale
224
424
624
OUTPUT CODE
824
1024
08541-038
–0.16
Figure 13. DNL Error with fIN = 9.7 MHz
1.0
85
0.8
SFDR (dBc)
0.6
0.4
INL ERROR (LSB)
75
70
0
–0.2
–0.4
–0.6
65
SNR (dBFS)
–0.8
0
10
20
30
40
50
SAMPLE RATE (MHz)
60
70
80
–1.0
08541-055
60
24
Figure 11. AD9609-80 SNR/SFDR vs. Sample Rate with AIN = 9.7 MHz
90
80
SFDRFS
70
SNR/SFDR (dBc/dBFS)
0.2
SNRFS
60
50
40
SFDR
30
SNR
20
0
–60
–50
–40
–20
–30
INPUT AMPLITUDE (dBc)
–10
0
08541-061
10
Figure 12. AD9609-80 SNR/SFDR vs. Input Amplitude (AIN) with fIN = 9.7 MHz
Rev. B | Page 12 of 32
224
424
624
OUTPUT CODE
Figure 14. INL with fIN = 9.7 MHz
824
1024
08541-037
SNR/SFDR (dBFS/dBc)
80
Data Sheet
AD9609
AD9609-65
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
0
65MSPS
9.7MHz @ –1dBFS
SNR = 60.6dB (61.6dBFS)
SFDR = 83.1dBc
–10
–30
SFDR/IMD3 (dBFS/dBc)
AMPLITUDE (dB)
–20
–40
–60
–80
SFDR (dBc)
–50
IMD3 (dBc)
–70
SFDR (dBFS)
–100
–90
–120
–110
–60
5
10
15
20
FREQUENCY (MHz)
25
30
0
–42
–36
–30
–24
–18
INPUT AMPLITUDE (dBFS)
–12
–6
85
65MSPS
70.3MHz @ –1dBFS
SNR = 60.6dB (61.6dBFS)
SFDR = 83.4dBc
80
SNR/SFDR (dBFS/dBc)
–20
–40
–60
–80
–100
SFDR (dBc)
75
70
65
SNR (dBFS)
60
55
0
5
10
15
20
FREQUENCY (MHz)
25
30
50
08541-032
–120
0
0
65MSPS
30.5MHz @ –1dBFS
SNR = 60.6dB (61.6dBFS)
SFDR = 83.9dBc
–40
–60
–80
0
5
10
15
20
FREQUENCY (MHz)
25
30
08541-031
–100
–120
100
150
AIN FREQUENCY (MHz)
200
Figure 19. AD9609-65 SNR/SFDR vs. Input Frequency (AIN) with
2 V p-p Full Scale
Figure 16. AD9609-65 Single-Tone FFT with fIN = 70.3 MHz
–20
50
08541-056
AMPLITUDE (dB)
–48
Figure 18. AD9609-65 SNR/SFDR vs. Input Amplitude (AIN) with fIN = 9.7 MHz
Figure 15. AD9609-65 Single-Tone FFT with fIN = 9.7 MHz
AMPLITUDE (dB)
–54
08541-060
0
08541-030
IMD3 (dBFS)
Figure 17. AD9609-65 Single-Tone FFT with fIN = 30.5 MHz
Rev. B | Page 13 of 32
AD9609
Data Sheet
AD9609-40
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
90
0
40MSPS
9.7MHz @ –1dBFS
SNR = 60.6dB (61.6dBFS)
SFDR = 82.0dBc
SFDRFS
80
70
SNR/SFDR (dBc/dBFS)
AMPLITUDE (dB)
–20
–40
–60
–80
SNRFS
60
50
40
SFDR
30
SNR
20
–100
0
5
10
FREQUENCY (MHz)
15
20
0
–60
08541-028
–120
0
40MSPS
30.5MHz @ –1dBFS
SNR = 60.6dB (61.6dBFS)
SFDR = 83.8dBc
–60
–80
–100
–120
2
4
6
8
10
12
14
FREQUENCY (MHz)
16
18
20
08541-029
AMPLITUDE (dB)
–40
0
–30
–40
–20
INPUT AMPLITUDE (dBc)
–10
0
Figure 22. AD9609-40 SNR/SFDR vs. Input Amplitude (AIN) with fIN = 9.7 MHz
Figure 20. AD9609-40 Single-Tone FFT with fIN = 9.7 MHz
–20
–50
08541-059
10
Figure 21. AD9609-40 Single-Tone FFT with fIN = 30.5 MHz
Rev. B | Page 14 of 32
Data Sheet
AD9609
AD9609-20
AVDD = 1.8 V; DRVDD = 1.8 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference; AIN = −1.0 dBFS, 50% duty
cycle clock, DCS disabled, unless otherwise noted.
0
90
20MSPS
9.7MHz @ –1dBFS
SNR = 60.6dBFS (61.6dBFS)
SFDR = 81.3dBc
SFDR (dBFS)
80
70
SNR/SFDR (dBc/dBFS)
AMPLITUDE (dB)
–20
–40
–60
–80
SNR (dBFS)
60
50
SFDR (dBc)
40
SNR (dBc)
30
20
–100
0
2
4
6
FREQUENCY (MHz)
8
10
0
–60
08541-024
–120
Figure 23. AD9609-20 Single-Tone FFT with fIN = 9.7 MHz
20MSPS
30.5MHz @ –1dBFS
SNR = 60.6dBFS (61.6dBFS)
SFDR = 84.0dBc
–60
–80
–100
–120
2
4
6
FREQUENCY (MHz)
8
10
08541-026
AMPLITUDE (dB)
–40
0
–40
–30
–20
INPUT AMPLITUDE (dBc)
–10
0
Figure 25. AD9609-20 SNR/SFDR vs. Input Amplitude (AIN) with fIN = 9.7 MHz
0
–20
–50
08541-058
10
Figure 24. AD9609-20 Single-Tone FFT with fIN = 30.5 MHz
Rev. B | Page 15 of 32
AD9609
Data Sheet
EQUIVALENT CIRCUITS
DRVDD
AVDD
08541-042
08541-039
VIN±
Figure 26. Equivalent Analog Input Circuit
Figure 30. Equivalent D0 to D9 and OR Digital Output Circuit
DRVDD
AVDD
SCLK/DFS,
MODE,
SDIO/PDWN
375Ω
VREF
30kΩ
Figure 27. Equivalent VREF Circuit
08541-043
08541-047
7.5kΩ
350Ω
Figure 31. Equivalent SCLK/DFS, MODE, and SDIO/PDWN Input Circuit
DRVDD
AVDD
AVDD
375Ω
30kΩ
350Ω
08541-045
CSB
08541-046
SENSE
Figure 32. Equivalent CSB Input Circuit
Figure 28. Equivalent SENSE Circuit
CLK+
5Ω
15kΩ
0.9V
AVDD
15kΩ
CLK–
5Ω
375Ω
08541-040
08541-044
RBIAS
AND VCM
Figure 33. Equivalent RBIAS and VCM Circuit
Figure 29. Equivalent Clock Input Circuit
Rev. B | Page 16 of 32
Data Sheet
AD9609
THEORY OF OPERATION
The output staging block aligns the data, corrects errors, and
passes the data to the CMOS output buffers. The output buffers
are powered from a separate (DRVDD) supply, allowing adjustment of the output voltage swing. During power-down, the
output buffers go into a high impedance state.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9609 is a differential switchedcapacitor circuit designed for processing differential input
signals. This circuit can support a wide common-mode range
while maintaining excellent performance. By using an input
common-mode voltage of midsupply, users can minimize
signal-dependent errors and achieve optimum performance.
Input Common Mode
The analog inputs of the AD9609 are not internally dc-biased.
Therefore, in ac-coupled applications, the user must provide a
dc bias externally. Setting the device so that VCM = AVDD/2 is
recommended for optimum performance, but the device can
function over a wider range with reasonable performance, as
shown in Figure 35 and Figure 36.
100
90
80
SFDR (dBc)
70
SNR (dBFS)
60
50
0.5
0.6
0.7
0.8
0.9
1.0
1.1
INPUT COMMON-MODE VOLTAGE (V)
1.2
1.3
08541-139
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor DAC
and an interstage residue amplifier (for example, a multiplying
digital-to-analog converter (MDAC)). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
high IF frequencies. Either a shunt capacitor or two single-ended
capacitors can be placed on the inputs to provide a matching
passive network. This ultimately creates a low-pass filter at the
input to limit unwanted broadband noise. See the AN-742
Application Note, the AN-827 Application Note, and the Analog
Dialogue article “Transformer-Coupled Front-End for Wideband
A/D Converters” (Volume 39, April 2005) for more information. In
general, the precise values depend on the application.
SNR/SFDR (dBFS/dBc)
The AD9609 architecture consists of a multistage, pipelined ADC.
Each stage provides sufficient overlap to correct for flash errors in
the preceding stage. The quantized outputs from each stage are
combined into a final 10-bit result in the digital correction logic.
The pipelined architecture permits the first stage to operate with a
new input sample while the remaining stages operate with preceding samples. Sampling occurs on the rising edge of the clock.
Figure 35. SNR/SFDR vs. Input Common-Mode Voltage,
fIN = 32.1 MHz, fS = 80 MSPS
H
100
CPAR
H
CSAMPLE
S
S
S
90
SNR/SFDR (dBFS/dBc)
S
CSAMPLE
VIN–
H
08541-006
H
CPAR
Figure 34. Switched-Capacitor Input Circuit
The clock signal alternately switches the input circuit between
sample-and-hold mode (see Figure 34). When the input circuit
is switched to sample mode, the signal source must be capable
of charging the sample capacitors and settling within one-half
of a clock cycle. A small resistor in series with each input can
help reduce the peak transient current injected from the output
stage of the driving source. In addition, low Q inductors or ferrite
beads can be placed on each leg of the input to reduce high differential capacitance at the analog inputs and, therefore, achieve
the maximum bandwidth of the ADC. Such use of low Q inductors
or ferrite beads is required when driving the converter front end at
80
SFDR (dBc)
70
SNR (dBFS)
60
50
0.5
0.6
0.7
0.8
0.9
1.0
1.1
INPUT COMMON-MODE VOLTAGE (V)
1.2
1.3
08541-140
VIN+
Figure 36. SNR/SFDR vs. Input Common-Mode Voltage,
fIN = 10.3 MHz, fS = 20 MSPS
An on-board, common-mode voltage reference is included in
the design and is available from the VCM pin. The VCM pin
must be decoupled to ground by a 0.1 µF capacitor, as described
in the Applications Information section.
Rev. B | Page 17 of 32
AD9609
Data Sheet
Differential Input Configurations
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9609. For applications above
~10 MHz where SNR is a key parameter, differential double balun
coupling is the recommended input configuration (see Figure 40).
Optimum performance is achieved while driving the AD9609 in a
differential input configuration. For baseband applications, the
AD8138, ADA4937-2, and ADA4938-2 differential drivers provide
excellent performance and a flexible interface to the ADC. The
output common-mode voltage of the ADA4938-2 is easily set
with the VCM pin of the AD9609 (see Figure 37), and the driver
can be configured in a Sallen-Key filter topology to provide
band limiting of the input signal.
10pF
ADA4938-2
120Ω
In any configuration, the value of Shunt Capacitor C is dependent
on the input frequency and source impedance and may need to
be reduced or removed. Table 9 displays the suggested values to set
the RC network. However, these values are dependent on the
input signal and should be used only as a starting guide.
AVDD
ADC
33Ω
VCM
VIN+
200Ω
Figure 37. Differential Input Configuration Using the ADA4938-2
Table 9. Example RC Network
For baseband applications below ~10 MHz where SNR is a key
parameter, differential transformer-coupling is the recommended
input configuration. An example is shown in Figure 38. To bias
the analog input, the VCM voltage can be connected to the
center tap of the secondary winding of the transformer.
2V p-p
49.9Ω
A single-ended input can provide adequate performance in costsensitive applications. In this configuration, SFDR and distortion
performance degrade due to the large input common-mode swing.
If the source impedances on each input are matched, there should
be little effect on SNR performance. Figure 39 shows a typical
single-ended input configuration.
ADC
C
R
C Differential (pF)
22
Open
Single-Ended Input Configuration
VIN+
R
R Series
(Ω Each)
33
125
Frequency Range (MHz)
0 to 70
70 to 200
VCM
08541-008
VIN–
0.1µF
Figure 38. Differential Transformer-Coupled Configuration
10µF
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies below
a few megahertz (MHz). Excessive signal power can also cause
core saturation, which leads to distortion.
AVDD
1kΩ
1V p-p
0.1µF
49.9Ω
R
AVDD
0.1µF
ADC
C
1kΩ
10µF
VIN+
1kΩ
R
VIN–
1kΩ
Figure 39. Single-Ended Input Configuration
0.1µF
0.1µF
R
VIN+
2V p-p
25Ω
PA
S
S
P
0.1µF
25Ω
ADC
C
0.1µF
R
VCM
VIN–
Figure 40. Differential Double Balun Input Configuration
VCC
0.1µF
ANALOG INPUT
0Ω
16
1
8, 13
11
2
CD
RD
RG
3
5
0.1µF 0Ω
R
VIN+
200Ω
10
ADC
C
AD8352
4
ANALOG INPUT
0.1µF
0.1µF
0.1µF
200Ω
R
14
0.1µF
0.1µF
Figure 41. Differential Input Configuration Using the AD8352
Rev. B | Page 18 of 32
VIN–
VCM
08541-011
0.1µF
VIN–
90Ω
08541-009
33Ω
08541-010
76.8Ω
08541-007
200Ω
VIN
An alternative to using a transformer-coupled input at frequencies
in the second Nyquist zone is to use the AD8352 differential driver.
An example is shown in Figure 41. See the AD8352 data sheet
for more information.
Data Sheet
AD9609
VOLTAGE REFERENCE
0
Internal Reference Connection
A comparator within the AD9609 detects the potential at the
SENSE pin and configures the reference into two possible modes,
which are summarized in Table 10. If SENSE is grounded, the
reference amplifier switch is connected to the internal resistor
divider (see Figure 42), setting VREF to 1.0 V.
–0.5
–1.0
INTERNAL VREF = 0.996V
–1.5
–2.0
–2.5
–3.0
0
0.2
0.4
0.8
0.6
1.0
1.2
1.4
1.6
1.8
2.0
LOAD CURRENT (mA)
08541-014
REFERENCE VOLTAGE ERROR (%)
A stable and accurate 1.0 V voltage reference is built into the
AD9609. The VREF can be configured using either the internal
1.0 V reference or an externally applied 1.0 V reference voltage.
The various reference modes are summarized in the sections that
follow. The Reference Decoupling section describes the best
practices for PCB layout of VREF.
Figure 43. VREF Accuracy vs. Load Current
VIN+
External Reference Operation
VIN–
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift characteristics. Figure 44 shows the typical drift characteristics of the
internal reference in 1.0 V mode.
ADC
CORE
VREF
4
1.0µF
0.1µF
SELECT
LOGIC
3
2
SENSE
VREF ERROR (mV)
08541-012
Figure 42. Internal Reference Configuration
In either internal or external reference mode, the maximum input
range of the ADC can be varied by configuring SPI Address 0x18
as shown in Table 11, resulting in a selectable differential span
from 1 V p-p to 2 V p-p.
If the internal reference of the AD9609 is used to drive multiple
converters to improve gain matching, the loading of the reference
by the other converters must be considered. Figure 43 shows
how the internal reference voltage is affected by loading.
1
0
–1
–2
–3
–4
–5
–6
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
08541-052
ADC
VREF ERROR (mV)
0.5V
Figure 44. Typical VREF Drift
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
7.5 kΩ load (see Figure 27). The internal buffer generates the positive and negative full-scale references for the ADC core. Therefore,
the external reference must be limited to a maximum of 1.0 V.
Table 10. Reference Configuration Summary
Selected Mode
Fixed Internal Reference
Fixed External Reference
SENSE Voltage (V)
AGND to 0.2
AVDD
Resulting VREF (V)
1.0 internal
1.0 applied to external VREF pin
Resulting Differential Span (V p-p)
2.0
2.0
Table 11. Scaled Differential Span Summary
Selected Mode
Fixed Internal or External Reference
Fixed Internal or External Reference
Fixed Internal or External Reference
Fixed Internal or External Reference
Fixed Internal or External Reference
Resulting VREF (V)
1.0 (internal or external)
1.0 (internal or external)
1.0 (internal or external)
1.0 (internal or external)
1.0 (internal or external)
SPI Register 0x18 (Hex)
0xC0
0xC8
0xD0
0xD8
0xE0
Rev. B | Page 19 of 32
Resulting Differential Span (V p-p)
1.0
1.14
1.33
1.6
2.0
AD9609
Data Sheet
CLOCK INPUT CONSIDERATIONS
For optimum performance, clock the AD9609 sample clock inputs,
CLK+ and CLK−, with a differential signal. The signal is typically
ac-coupled into the CLK+ and CLK− pins via a transformer or
capacitors. These pins are biased internally (see Figure 45) and
require no external bias.
If a low jitter clock source is not available, another option is to
ac couple a differential PECL signal to the sample clock input
pins, as shown in Figure 48. The AD9510/AD9511/AD9512/
AD9513/AD9514/AD9515/AD9516-4/AD9517-4 clock drivers
offer excellent jitter performance.
AVDD
0.1µF
0.1µF
CLOCK
INPUT
CLK+
0.9V
0.1µF
CLOCK
INPUT
CLK–
CLK–
50kΩ
240Ω
50kΩ
The AD9609 has a very flexible clock input structure. The clock
input can be a CMOS, LVDS, LVPECL, or sine wave signal.
Regardless of the type of signal being used, clock source jitter is
of great concern, as described in the Jitter Considerations section.
Figure 46 and Figure 47 show two preferred methods for clocking the AD9609 (at clock rates up to 625 MHz). A low jitter clock
source is converted from a single-ended signal to a differential
signal using either an RF transformer or an RF balun.
The RF balun configuration is recommended for clock frequencies
between 125 MHz and 625 MHz, and the RF transformer is
recommended for clock frequencies from 10 MHz to 200 MHz.
The back-to-back Schottky diodes across the transformer/
balun secondary limit clock excursions into the AD9609 to
approximately 0.8 V p-p differential.
This limit helps prevent the large voltage swings of the clock
from feeding through to other portions of the AD9609 while
preserving the fast rise and fall times of the signal that are
critical to a low jitter performance.
A third option is to ac couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 49. The AD9510/
AD9511/AD9512/AD9513/AD9514/AD9515/AD9516-4/
AD9517-4 clock drivers offer excellent jitter performance.
0.1µF
0.1µF
CLOCK
INPUT
CLK+
0.1µF
CLOCK
INPUT
AD951x
LVDS DRIVER
50kΩ
50kΩ
Figure 49. Differential LVDS Sample Clock (Up to 625 MHz)
In some applications, it may be acceptable to drive the sample
clock inputs with a single-ended 1.8 V CMOS signal. In such
applications, drive the CLK+ pin directly from a CMOS gate, and
bypass the CLK− pin to ground with a 0.1 μF capacitor (see
Figure 50).
VCC
0.1µF
CLOCK
INPUT
50Ω1
1kΩ
AD951x
CMOS DRIVER
1kΩ
CLK–
150Ω
CLK+
CLK–
08541-017
SCHOTTKY
DIODES:
HSMS2822
Figure 46. Transformer-Coupled Differential Clock (Up to 200 MHz)
Input Clock Divider
The AD9609 contains an input clock divider with the ability to
divide the input clock by integer values between 1 and 8. Optimum
performance can be obtained by enabling the internal duty cycle
stabilizer (DCS) when using divide ratios other than 1, 2, or 4.
0.1µF
CLK+
ADC
0.1µF
1nF
08541-018
CLK–
SCHOTTKY
DIODES:
HSMS2822
RESISTOR IS OPTIONAL.
Figure 50. Single-Ended 1.8 V CMOS Input Clock (Up to 200 MHz)
ADC
0.1µF
50Ω
ADC
0.1µF
100Ω
1nF
CLK+
0.1µF
0.1µF
CLOCK
INPUT
OPTIONAL
0.1µF
100Ω
08541-021
XFMR
ADC
0.1µF
CLK–
Mini-Circuits®
ADT1-1WT, 1:1 Z
0.1µF
100Ω
08541-020
Clock Input Options
50Ω
240Ω
Figure 48. Differential PECL Sample Clock (Up to 625 MHz)
Figure 45. Equivalent Clock Input Circuit
CLOCK
INPUT
ADC
0.1µF
2pF
08541-016
2pF
100Ω
08541-019
CLK+
AD951x
PECL DRIVER
Figure 47. Balun-Coupled Differential Clock (Up to 625 MHz)
Rev. B | Page 20 of 32
Data Sheet
AD9609
Clock Duty Cycle
Jitter Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be sensitive
to clock duty cycle. Commonly, a ±5% tolerance is required on
the clock duty cycle to maintain dynamic performance
characteristics.
High speed, high resolution ADCs are sensitive to the quality of
the clock input. The degradation in SNR from the low frequency
SNR (SNRLF) at a given input frequency (fINPUT) due to jitter
(tJRMS) can be calculated by
SNRHF = −10 log[(2π × fINPUT × tJRMS)2 + 10 ( − SNRLF /10) ]
In the previous equation, the rms aperture jitter represents the
clock input jitter specification. IF undersampling applications
are particularly sensitive to jitter, as illustrated in Figure 52.
80
75
Jitter in the rising edge of the input is still of concern and is not
easily reduced by the internal stabilization circuit. The duty
cycle control loop does not function for clock rates less than
20 MHz nominally. The loop has a time constant associated
with it that must be considered in applications in which the
clock rate can change dynamically. A wait time of 1.5 µs to 5 µs
is required after a dynamic clock frequency increase or decrease
before the DCS loop is relocked to the input signal.
0.05ps
70
SNR (dBFS)
0.2ps
65
0.5ps
60
55
1.0ps
1.5ps
50
3.0ps
45
80
1
10
2.0ps
2.5ps
100
FREQUENCY (MHz)
75
1k
08541-022
The AD9609 contains a duty cycle stabilizer (DCS) that retimes
the nonsampling (falling) edge, providing an internal clock
signal with a nominal 50% duty cycle. This allows the user to
provide a wide range of clock input duty cycles without affecting
the performance of the AD9609. Noise and distortion performance
are nearly flat for a wide range of duty cycles with the DCS on,
as shown in Figure 51.
Figure 52. SNR vs. Input Frequency and Jitter
The clock input should be treated as an analog signal when
aperture jitter may affect the dynamic range of the AD9609. To
avoid modulating the clock signal with digital noise, keep power
supplies for clock drivers separate from the ADC output driver
supplies. Low jitter, crystal-controlled oscillators make the best
clock sources. If the clock is generated from another type of source
(by gating, dividing, or another method), it should be retimed by
the original clock at the last step.
DCS ON
65
60
55
DCS OFF
50
45
40
10
20
50
60
40
30
POSITIVE DUTY CYCLE (%)
70
80
08541-053
SNR (dBFS)
70
For more information, see the AN-501 Application Note and
the AN-756 Application Note.
Figure 51. SNR vs. DCS On/Off
Rev. B | Page 21 of 32
AD9609
Data Sheet
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 53, the analog core power dissipated by the
AD9609 is proportional to its sample rate. The digital power
dissipation of the CMOS outputs are determined primarily by
the strength of the digital drivers and the load on each output bit.
The maximum DRVDD current (IDRVDD) can be calculated as
IDRVDD = VDRVDD × CLOAD × fCLK × N
where N is the number of output bits (22, in the case of the
AD9609).
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the Nyquist
frequency of fCLK/2. In practice, the DRVDD current is established by the average number of output bits switching, which
is determined by the sample rate and the characteristics of the
analog input signal.
Reducing the capacitive load presented to the output drivers can
minimize digital power consumption. The data in Figure 53 was
taken using the same operating conditions as those used for the
Typical Performance Characteristics, with a 5 pF load on each
output driver.
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. See the Memory Map section
for more details.
DIGITAL OUTPUTS
The AD9609 output drivers can be configured to interface with
1.8 V to 3.3 V CMOS logic families. Output data can also be
multiplexed onto a single output bus to reduce the total number
of traces required.
The CMOS output drivers are sized to provide sufficient output
current to drive a wide variety of logic families. However, large
drive currents tend to cause current glitches on the supplies and
may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fanouts may require external buffers or latches.
85
80
ANALOG CORE POWER (mW)
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering powerdown mode and then must be recharged when returning to normal
operation. As a result, wake-up time is related to the time spent
in power-down mode, and shorter power-down cycles result in
proportionally shorter wake-up times.
The output data format can be selected to be either offset binary
or twos complement by setting the SCLK/DFS pin when operating
in the external pin mode (see Table 12).
75
70
65
AD9609-80
As detailed in the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI control.
60
55
AD9609-65
50
Table 12. SCLK/DFS and SDIO/PDWN Mode Selection
(External Pin Mode)
AD9609-40
45
40
20
30
40
50
60
CLOCK RATE (MSPS)
70
80
08541-051
AD9609-20
35
10
Figure 53. AD9609 Analog Core Power vs. Clock Rate
In SPI mode, the AD9609 can be placed in power-down mode
directly via the SPI port, or by using the programmable external
MODE pin. In non-SPI mode, power-down is achieved by asserting the PDWN pin high. In this state, the ADC typically dissipates
500 µW. During power-down, the output drivers are placed in a
high impedance state. Asserting PDWN low (or the MODE pin
in SPI mode) returns the AD9609 to its normal operating mode.
Note that PDWN is referenced to the digital output driver supply
(DRVDD) and should not exceed that supply voltage.
Voltage at Pin
AGND
SCLK/DFS
Offset binary (default)
DRVDD
Twos complement
SDIO/PDWN
Normal operation
(default)
Outputs disabled
Digital Output Enable Function (OEB)
When using the SPI interface, the data outputs and DCO can be
independently three-stated by using the programmable external
MODE pin. The MODE pin (OEB) function is enabled via
Bits[6:5] of Register 0x08.
If the MODE pin is configured to operate in traditional OEB
mode, and the MODE pin is low, the output data drivers and
DCOs are enabled. If the MODE pin is high, the output data
drivers and DCOs are placed in a high impedance state. This
OEB function is not intended for rapid access to the data bus.
Note the MODE pin is referenced to the digital output driver
supply (DRVDD) and should not exceed that supply voltage.
Rev. B | Page 22 of 32
Data Sheet
AD9609
TIMING
The AD9609 provides latched data with a pipeline delay of eight
clock cycles. Data outputs are available one propagation delay
(tPD) after the rising edge of the clock signal.
Minimize the length of the output data lines and loads placed
on them to reduce transients within the AD9609. These transients
can degrade converter dynamic performance.
The lowest typical conversion rate of the AD9609 is 3 MSPS. At
clock rates below 3 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9609 provides a data clock output (DCO) signal intended
for capturing the data in an external register. The CMOS data
outputs are valid on the rising edge of DCO, unless the DCO
clock polarity has been changed via the SPI. See Figure 2 for a
graphical timing description.
Table 13. Output Data Format
Input (V)
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
Condition (V)
< −VREF − 0.5 LSB
= −VREF
=0
= +VREF − 1.0 LSB
> +VREF − 0.5 LSB
Offset Binary Output Mode
00 0000 0000
00 0000 0000
10 0000 0000
11 1111 1111
11 1111 1111
Rev. B | Page 23 of 32
Twos Complement Mode
10 0000 0000
10 0000 0000
00 0000 0000
01 1111 1111
01 1111 1111
OR
1
0
0
0
1
AD9609
Data Sheet
BUILT-IN SELF-TEST (BIST) AND OUTPUT TEST
The AD9609 includes a built-in test feature designed to enable
verification of the integrity of each channel as well as to facilitate board level debugging. A built-in self-test (BIST) feature that
verifies the integrity of the digital datapath of the AD9609 is
included. Various output test options are also provided to place
predictable values on the outputs of the AD9609.
BUILT-IN SELF-TEST (BIST)
The BIST is a thorough test of the digital portion of the selected
AD9609 signal path. Perform the BIST test after a reset to ensure
that the part is in a known state. During BIST, data from an internal
pseudorandom noise (PN) source is driven through the digital
datapath of both channels, starting at the ADC block output.
At the datapath output, CRC logic calculates a signature from
the data. The BIST sequence runs for 512 cycles and then stops.
Once completed, the BIST compares the signature results with a
pre-determined value. If the signatures match, the BIST sets Bit 0
of Register 0x24, signifying the test passed. If the BIST test failed,
Bit 0 of Register 0x24 is cleared. The outputs are connected during
this test, so the PN sequence can be observed as it runs. Writing
0x05 to Register 0x0E runs the BIST. This enables the Bit 0 (BIST
enable) of Register 0x0E and resets the PN sequence generator,
Bit 2 (BIST INIT) of Register 0x0E. At the completion of the BIST,
Bit 0 of Register 0x24 is automatically cleared. The PN sequence
can be continued from its last value by writing a 0 in Bit 2 of
Register 0x0E. However, if the PN sequence is not reset, the
signature calculation does not equal the predetermined value at
the end of the test. At that point, the user needs to rely on
verifying the output data.
OUTPUT TEST MODES
The output test options are described in Table 17 at Address 0x0D.
When an output test mode is enabled, the analog section of the
ADC is disconnected from the digital back-end blocks and the
test pattern is run through the output formatting block. Some of
the test patterns are subject to output formatting, and some are
not. The PN generators from the PN sequence tests can be reset
by setting Bit 4 or Bit 5 of Register 0x0D. These tests can be
performed with or without an analog signal (if present, the analog
signal is ignored), but they do require an encode clock. For more
information, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI.
Rev. B | Page 24 of 32
Data Sheet
AD9609
SERIAL PORT INTERFACE (SPI)
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 54 and
Table 5.
The AD9609 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port and
can be written to or read from via the port. Memory is organized
into bytes that can be further divided into fields, which are
documented in the Memory Map section. For detailed operational
information, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device; this is
called streaming. The CSB can stall high between bytes to allow for
additional external timing. When CSB is tied high, SPI functions
are placed in high impedance mode. This mode turns on any
SPI pin secondary functions.
CONFIGURATION USING THE SPI
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits, as shown in Figure 54.
Three pins define the SPI of this ADC: SCLK, SDIO, and CSB
(see Table 14). The SCLK (a serial clock) is used to synchronize
the read and write data presented from and to the ADC. SDIO
(serial data input/output) is a dual-purpose pin that allows data to
be sent and read from the internal ADC memory map registers.
The CSB (chip select bar) is an active-low control that enables
or disables the read and write cycles.
All data is composed of 8-bit words. The first bit of the first byte
in a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction from an input
to an output at the appropriate point in the serial frame.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Table 14. Serial Port Interface Pins
Pin
SCLK
SDIO
CSB
Function
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip select bar. An active-low control that gates the read
and write cycles.
tHIGH
tDS
tS
tDH
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this and
other features, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI.
tH
tCLK
tLOW
CSB
SDIO DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
Figure 54. Serial Port Interface Timing Diagram
Rev. B | Page 25 of 32
D4
D3
D2
D1
D0
DON’T CARE
08541-023
DON’T CARE
SCLK DON’T CARE
AD9609
Data Sheet
HARDWARE INTERFACE
CONFIGURATION WITHOUT THE SPI
The pins described in Table 14 constitute the physical interface
between the programming device of the user and the serial port
of the AD9609. The SCLK pin and the CSB pin function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
In applications that do not interface to the SPI control registers,
the SDIO/PDWN pin and the SCLK/DFS pin serve as standalone
CMOS-compatible control pins. When the device is powered up, it
is assumed that the user intends to use the pins as static control
lines for the power-down and output data format feature control.
In this mode, connect the CSB chip select to DRVDD, which
disables the serial port interface.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9609 to prevent these signals from transitioning at the converter inputs during critical sampling periods.
SDIO/PDWN and SCLK/DFS serve a dual function when the
SPI interface is not being used. When the pins are strapped to
DRVDD or ground during device power-on, they are associated
with a specific function. The Digital Outputs section describes
the strappable functions supported on the AD9609.
Table 15. Mode Selection
Pin
SDIO/PDWN
SCLK/DFS
External
Voltage
DRVDD
AGND (default)
DRVDD
AGND (default)
Configuration
Chip power-down mode
Normal operation (default)
Twos complement enabled
Offset binary enabled
SPI ACCESSIBLE FEATURES
Table 16 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI. The AD9609 part-specific features are described in
detail in Table 17.
Table 16. Features Accessible Using the SPI
Feature
Modes
Clock
Offset
Test I/O
Output Mode
Output Phase
Output Delay
VREF
Rev. B | Page 26 of 32
Description
Allows the user to set either power-down mode
or standby mode
Allows the user to access the DCS via the SPI
Allows the user to digitally adjust the
converter offset
Allows the user to set test modes to have known
data on output bits
Allows the user to set up outputs
Allows the user to set the output clock polarity
Allows the user to vary the DCO delay
Allows the user to set the reference voltage
Data Sheet
AD9609
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
DEFAULT VALUES
Each row in the memory map register table (see Table 17)
contains eight bit locations. The memory map is roughly
divided into four sections: the chip configuration registers
(Address 0x00 to Address 0x02); the device index and transfer
register (Address 0xFF); the program registers, including setup,
control, and test (Address 0x08 to Address 0x2A); and the
AD9609-specific customer SPI control register (Address 0x101).
After the AD9609 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table (see Table 17).
Table 17 documents the default hexadecimal value for each
hexadecimal address shown. The column with the heading Bit 7
(MSB) is the start of the default hexadecimal value given. For
example, Address 0x2A, the OR/MODE select register, has a hexadecimal default value of 0x01. This means that in Address 0x2A,
Bits[7:1] = 0, and Bit 0 = 1. This setting is the default OR/MODE
setting. The default value results in the programmable external
MODE/OR pin (Pin 23) functioning as an out-of-range digital
output. For more information on this function and others, see the
AN-877 Application Note, Interfacing to High Speed ADCs via SPI.
This application note details the functions controlled by Register
0x00 to Register 0xFF. The remaining register, Register 0x101, is
documented in the Memory Map Register Descriptions section
that follows Table 17.
Logic Levels
An explanation of logic level terminology follows:
•
•
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simultaneously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and then the bit autoclears.
OPEN LOCATIONS
All address and bit locations that are not included in the SPI map
are not currently supported for this device. Unused bits of a valid
address location should be written with 0s. Writing to these locations is required only when part of an address location is open
(for example, Address 0x2A). If the entire address location is
open, it is omitted from the SPI map (for example, Address 0x13)
and should not be written.
Rev. B | Page 27 of 32
AD9609
Data Sheet
MEMORY MAP REGISTER TABLE
All address and bit locations that are not included in Table 17 are not currently supported for this device.
Table 17.
Addr
(Hex)
Register Name
Chip Configuration Registers
0x00
SPI port
configuration
0x01
Chip ID
0x02
Chip grade
Bit 7
(MSB)
0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
LSB
first
Soft
reset1
1
1
Soft
reset1
LSB
first
Default
Value
(Hex)
0
0x18
8-bit chip ID, Bits[7:0]
AD9609 = 0x71
Open
Device Index and Transfer Register
0xFF
Transfer
Open
Program Registers
0x08
Modes
Bit 6
Bit 0
(LSB)
External
Pin 23
mode
input
enable
Speed grade ID, Bits[6:4]
(identify device variants of
chip ID)
20 MSPS = 000
40 MSPS = 001
65 MSPS = 010
80 MSPS = 011
Open
Open
Read only
Read only
Open
Open
Open
Open
Open
External Pin 23
function when
high
00 = full power
down
01 = standby
10 = normal
mode: output
disabled
11 = normal
mode: output
enabled
Open Open
Open
Open
Open
0x09
Clock
Open
0x0B
Clock divide
Open
0x0D
Test mode
User test mode
00 = single
01 = alternate
10 = single once
11 = alternate once
Reset
PN
long
gen
Reset
PN
short
gen
0x0E
BIST enable
Open
Open
Open
Open
Open
Transfer
The nibbles are
mirrored so that LSB
or MSB first mode
registers correctly,
regardless of shift
mode
Unique chip ID used
to differentiate
devices; read only
Unique speed grade
ID used to
differentiate
devices; read only
0x00
Synchronously
transfers data from
the master shift
register to the slave
00 = chip run
01 = full power-down
10 = standby
11 = chip wide digital
reset
0x00
Determines various
generic modes of
chip operation
Open
0x01
Enable internal duty
cycle stabilizer (DCS)
The divide ratio is
the value plus 1
Duty cycle
stabilize
Clock divider, Bits[2:0]
Clock divide ratio
000 = divide by 1
001 = divide by 2
010 = divide by 3
011 = divide by 4
100 = divide by 5
101 = divide by 6
110 = divide by 7
111 = divide by 8
Output test mode, Bits[3:0] (local)
0000 = off (default)
0001 = midscale short
0010 = positive FS
0011 = negative FS
0100 = alternating checkerboard
0101 = PN 23 sequence
0110 = PN 9 sequence
0111 = 1/0 word toggle
1000 = user input
1001 = 1/0 bit toggle
1010 = 1× sync
1011 = one bit high
1100 = mixed bit frequency
Open BIST
Open BIST enable
INIT
Rev. B | Page 28 of 32
Comments
0x00
0x00
When set, the test
data is placed on
the output pins in
place of normal
data
0x00
When Bit 0 is set,
the built in self-test
Data Sheet
AD9609
Addr
(Hex)
Bit 7
(MSB)
Register Name
0x10
Offset adjust
0x14
Output mode
0x15
Output adjust
0x16
Output phase
DCO
Output
polarity
0=
normal
1=
inverted
Open
Open
Open
0x17
Output delay
Enable
DCO
delay
Open
Enable
data
delay
Open
0x18
VREF
Reserved =11
0x19
USER_PATT1_LSB
B7
B6
Internal VREF adjustment,
Bits[2:0]
000 = 1.0 V p-p
001 = 1.14 V p-p
010 = 1.33 V p-p
011 = 1.60 V p-p
100 = 2.0 V p-p
B5
B4
B3
0x1A
USER_PATT1_MSB
B15
B14
B13
B12
0x1B
USER_PATT2_LSB
B7
B6
B5
0x1C
USER_PATT2_MSB
B15
B14
B13
0x24
BIST signature LSB
0x2A
OR/MODE select
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
8-bit device offset adjustment, Bits[7:0] (local)
Offset adjust in LSBs from +127 to −128 (twos complement format)
00 = 3.3 V CMOS
Open
Output
Open Output
00 = offset binary
10 = 1.8 V CMOS
disable
invert
01 = twos complement
10 = gray code
11 = offset binary
1.8 V data
3.3 V data
1.8 V DCO
3.3 V DCO
drive strength
drive strength
drive strength
drive strength
00 = 1 stripe
00 = 1 stripe
00 = 1 stripe
00 = 1 stripe
01 = 2 stripes
(default)
01 = 2 stripes
(default)
10 = 3 stripes (default)
01 = 2 stripes
10 = 3 stripes
01 = 2 stripes
11 = 4 stripes
10 = 3 stripes
(default)
10 = 3 stripes
11 = 4 stripes
11 = 4 stripes
11 = 4 stripes
Open
Open
Open
Open
Open
Default
Value
(Hex)
Comments
function is initiated.
0x00
Device offset trim
0x00
Configures the
outputs and the
format of the data
0x22
Determines CMOS
output drive
strength properties
0x00
On devices that
utilize global clock
divide, determines
which phase of the
divider output is
used to supply the
output clock;
internal latching is
unaffected
Input clock phase adjust, Bits[2:0]
(Value is number of input clock
cycles of phase delay)
000 = no delay
001 = 1 input clock cycle
010 = 2 input clock cycles
011 = 3 input clock cycles
100 = 4 input clock cycles
101 = 5 input clock cycles
110 = 6 input clock cycles
111 = 7 input clock cycles
DCO/data delay[2:0]
000 = 0.56 ns
001 = 1.12 ns
010 = 1.68 ns
011 = 2.24 ns
100 = 2.80 ns
101 = 3.36 ns
110 = 3.92 ns
111 = 4.48 ns
Open
0x00
Sets the fine output
delay of the output
clock but does not
change internal
timing
0xE0
Selects and/or
adjusts the VREF
full-scale span
B2
B1
B0
0x00
B11
B10
B9
B8
0x00
B4
B3
B2
B1
B0
0x00
B12
B11
B10
B9
B8
0x00
User-defined
pattern, 1 LSB
User-defined
pattern, 1 MSB
User-defined
pattern, 2 LSB
User-defined
pattern, 2 MSB
Least significant
byte of BIST
signature, read only
Selects I/O
functionality in
conjunction with
Address 0x08 for
MODE (input) or OR
(output) on external
Pin 23
BIST signature, Bits[7:0]
1.1. AD9609-Specific Customer SPI Control
0x101
USR2
1
1.
Bit 6
Bit 0
(LSB)
Open
0x00
Open
Open
Open
0 = MODE
1 = OR
(default)
0x01
Enable
GCLK
detect
Run
GCLK
Open
Disable SDIO
pull-down
0x88
See the Soft Reset section for limitations on the use of soft reset.
Rev. B | Page 29 of 32
Enables internal
oscillator for clock
rates <5 MHz
AD9609
Data Sheet
MEMORY MAP REGISTER DESCRIPTIONS
Bit 2—Run GCLK
For additional information about functions controlled in
Register 0x00 to Register 0xFF, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
This bit enables the GCLK oscillator. For some applications
with encode rates below 10 MSPS, it may be preferable to set
this bit high to supersede the GCLK detector.
USR2 (Register 0x101)
Bit 3—Enable GCLK Detect
Bit 0—Disable SDIO Pull-Down
Normally set high, this bit enables a circuit that detects encode
rates below about 5 MSPS. When a low encode rate is detected,
an internal oscillator, GCLK, is enabled ensuring the proper
operation of several circuits. If set low, the detector is disabled.
This bit can be set high to disable the internal 30 kΩ pull-down
on the SDIO pin, which can be used to limit the loading when
many devices are connected to the SPI bus.
Rev. B | Page 30 of 32
Data Sheet
AD9609
APPLICATIONS INFORMATION
DESIGN GUIDELINES
Before starting design and layout of the AD9609 as a system, it
is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements needed for certain pins.
Power and Ground Recommendations
When connecting power to the AD9609, it is strongly
recommended that two separate supplies be used. Use one 1.8 V
supply for analog (AVDD); use a separate 1.8 V to 3.3 V supply for
the digital output supply (DRVDD). If a common 1.8 V AVDD
and DRVDD supply must be used, the AVDD and DRVDD
domains must be isolated with a ferrite bead or filter choke and
separate decoupling capacitors. Several different decoupling
capacitors can be used to cover both high and low frequencies.
Locate these capacitors close to the point of entry at the PCB
level and close to the pins of the part, with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9609. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
is easily achieved.
When powering down the AD9609, power off AVDD and
DRVDD simultaneously, or DRVDD must be removed before
AVDD.
Encode Clock
For optimum dynamic performance a low jitter encode clock
source with a 50% duty cycle ±5% should be used to clock the
AD9609.
VCM
The VCM pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 38.
RBIAS
The AD9609 requires that a 10 kΩ resistor be placed between
the RBIAS pin and ground. This resistor sets the master current
reference of the ADC core and should have at least a 1% tolerance.
Reference Decoupling
Exposed Paddle Thermal Heat Sink Recommendations
The exposed paddle (Pin 0) is the only ground connection for
the AD9609; therefore, it must be connected to analog ground
(AGND) on the customer’s PCB. To achieve the best electrical
and thermal performance, mate an exposed (no solder mask)
continuous copper plane on the PCB to the AD9609 exposed
paddle, Pin 0.
The copper plane should have several vias to achieve the
lowest possible resistive thermal path for heat dissipation to
flow through the bottom of the PCB. Fill or plug these vias
with nonconductive epoxy.
To maximize the coverage and adhesion between the ADC and
the PCB, a silkscreen should be overlaid to partition the continuous
plane on the PCB into several uniform sections. This provides
several tie points between the ADC and the PCB during the reflow
process. Using one continuous plane with no partitions guarantees
only one tie point between the ADC and the PCB. For detailed
information about packaging and PCB layout of chip scale
packages, see the AN-772 Application Note, A Design and
Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP).
Externally decoupled the VREF pin to ground with a low ESR, 1.0
μF capacitor in parallel with a low ESR, 0.1 μF ceramic capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9609 to keep these signals from transitioning at the converter
inputs during critical sampling periods.
Soft Reset
In applications with DRVDD ≥ 2.75 V, do not perform soft reset
(Register 0x00 Bit 2 and Bit 5 = 1). Soft reset restores AD9609
defaults already available at power-up and is not needed.
Rev. B | Page 31 of 32
AD9609
Data Sheet
OUTLINE DIMENSIONS
0.30
0.25
0.18
32
25
0.50
BSC
0.80
0.75
0.70
0.50
0.40
0.30
8
16
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
3.65
3.50 SQ
3.45
EXPOSED
PAD
17
TOP VIEW
PIN 1
INDICATOR
1
24
9
BOTTOM VIEW
0.25 MIN
3.50 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD.
04-02-2012-A
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
Figure 55. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
9 mm × 9 mm Body, Very Very Thin Quad
(CP-32-11)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
AD9609BCPZ-80
AD9609BCPZRL7-80
AD9609BCPZ-65
AD9609BCPZRL7-65
AD9609BCPZ-40
AD9609BCPZRL7-40
AD9609BCPZ-20
AD9609BCPZRL7-20
AD9609-80EBZ
AD9609-65EBZ
AD9609-40EBZ
AD9609-20EBZ
1
2
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
Z = RoHS Compliant Part.
For the AD9609BCPZ models, the exposed paddle (Pin 0) is the only GND connection on the chip and must be connected to the PCB AGND.
©2009–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08541-0-2/17(B)
Rev. B | Page 32 of 32
Package Option
CP-32-11
CP-32-11
CP-32-11
CP-32-11
CP-32-11
CP-32-11
CP-32-11
CP-32-11
Similar pages