ON ESD7361P2T5G Esd protection diode Datasheet

ESD7361, SZESD7361
ESD Protection Diodes
Low Capacitance ESD Protection Diode
for High Speed Data Line
The ESD7361 Series ESD protection diodes are designed to protect
high speed data lines from ESD. Ultra−low capacitance make this
device an ideal solution for protecting voltage sensitive high speed
data lines.
www.onsemi.com
MARKING
DIAGRAMS
Features
2
IEC61000−4−2 (ESD): Level 4 ±15 kV Contact
♦ IEC61000−4−4 (EFT): 40 A −5/50 ns
♦ IEC61000−4−5 (Lightning): 1 A (8/20 ms)
ISO 10605 (ESD) 330 pF/2 kW ±15 kV Contact
SZ Prefix for Automotive and Other Applications Requiring Unique
Site and Control Change Requirements; AEC−Q101 Qualified and
PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
♦
•
•
•
Typical Applications
1
2
SOD−523
CASE 502
1
7H
M
7X
1
2
SOD−923
CASE 514AB
X, XX
M
• Wireless Charger
• Near Field Communications
2M
= Specific Device Code
= Date Code
PIN CONFIGURATION
AND SCHEMATIC
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Operating Junction Temperature Range
TJ
−55 to +125
°C
Storage Temperature Range
Tstg
−55 to +150
°C
Lead Solder Temperature −
Maximum (10 Seconds)
TL
260
°C
ESD
ESD
ESD
±15
±15
±15
kV
kV
kV
IEC 61000−4−2 Contact (ESD)
IEC 61000−4−2 Air (ESD)
ISO 10605 330 pF/2 kW Contact (ESD)
SOD−323
CASE 477
M
• Low Capacitance (0.55 pF Max, I/O to GND)
• Protection for the Following IEC Standards:
1
Cathode
2
Anode
ORDERING INFORMATION
See detailed ordering and shipping information on page 6 of
this data sheet.
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
© Semiconductor Components Industries, LLC, 2016
November, 2016 − Rev. 3
1
Publication Order Number:
ESD7361/D
ESD7361, SZESD7361
ELECTRICAL CHARACTERISTICS
I
(TA = 25°C unless otherwise noted)
IF
Parameter
Symbol
IPP
Maximum Reverse Peak Pulse Current
VC
Clamping Voltage @ IPP
VRWM
VC VBR VRWM
Working Peak Reverse Voltage
IR
VBR
V
IR VF
IT
Maximum Reverse Leakage Current @ VRWM
Breakdown Voltage @ IT
IT
Test Current
*See Application Note AND8308/D for detailed explanations of
datasheet parameters.
IPP
Uni−Directional TVS
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified)
Parameter
Symbol
Reverse Working Voltage
Conditions
Min
Typ
Max
Unit
5
16
V
1000
1000
nA
nA
VRWM
Breakdown Voltage
VBR
IT = 1 mA; pin 1 to pin 2
16.5
V
Reverse Leakage Current
IR
VRWM = 5.0 V
VRWM = 15 V
<1
20
Clamping Voltage (Note 2)
VC
IPP = 8 A
31
V
Clamping Voltage (Note 2)
VC
IPP = 16 A
34
V
Junction Capacitance
CJ
VR = 0 V, f = 1 MHz
VR = 0 V, f < 1 GHz
Dynamic Resistance
RDYN
Insertion Loss
0.55
0.55
pF
TLP Pulse
0.735
W
f = 1 MHz
f = 5 GHz
0.01
2
dB
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. For test procedure see Figures 9 and 10 and application note AND8307/D.
2. ANSI/ESD STM5.5.1 − Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model.
TLP conditions: Z0 = 50 W, tp = 100 ns, tr = 4 ns, averaging window; t1 = 30 ns to t2 = 60 ns.
1.E−03
1
1.E−04
0.8
CAPACITANCE (pF)
CURRENT (A)
1.E−05
1.E−06
1.E−07
1.E−08
1.E−09
1.E−10
1.E−11
0.6
0.4
0.2
1.E−12
1.E−13
0
5
10
15
20
25
30
0
0
2
4
6
8
10
12
14
VOLTAGE (V)
VBias (V)
Figure 1. Typical IV Characteristics
Figure 2. Typical CV Characteristics
www.onsemi.com
2
16
18
ESD7361, SZESD7361
1
0.9
0
0.8
CAPACITANCE (pF)
1
0.5
S21 (dB)
−0.5
−1
−1.5
−2
−2.5
0.7
0.6
0.5
0.4
0.3
−3
0.2
−3.5
0.1
−4
1.E+07
1.E+08
0
1.E+07
1.E+09
5.E+08
1.E+09
Figure 4. Typical Capacitance Over Frequency
ESD7361HT1G (SOD323)
1
0.5
0.9
0
0.8
CAPACITANCE (pF)
1
S21 (dB)
−0.5
−1
−1.5
−2
−2.5
0.7
0.6
0.5
0.4
0.3
−3
0.2
−3.5
0.1
1.E+08
0
1.E+07
1.E+09
1.E+09
FREQUENCY (Hz)
1
1
0.9
0
0.8
−0.5
0.7
CURRENT (A)
S21 (dB)
3.E+09
4.E+09
Figure 6. Typical Capacitance Over Frequency
ESD7361XV2T1G (SOD523)
0.5
−1
−1.5
−2
−2.5
0.6
0.5
0.4
0.3
−3
0.2
−3.5
0.1
1.E+08
2.E+09
FREQUENCY (Hz)
Figure 5. Typical Insertion Loss
ESD7361XV2T1G (SOD523)
−4
1.E+07
2.E+09 3.E+09
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 3. Typical Insertion Loss
ESD7361HT1G (SOD323)
−4
1.E+07
2.E+09
0
1.E+07
1.E+09
1.E+09
2.E+09
3.E+09
4.E+09
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 7. Typical Insertion Loss
ESD7361P2T5G (SOD923)
Figure 8. Typical Capacitance Over Frequency
ESD7361P2T5G (SOD923)
www.onsemi.com
3
ESD7361, SZESD7361
IEC61000−4−2 Waveform
IEC 61000−4−2 Spec.
Ipeak
Level
Test Voltage (kV)
First Peak
Current
(A)
Current at
30 ns (A)
Current at
60 ns (A)
1
2
7.5
4
2
2
4
15
8
4
3
6
22.5
12
6
4
8
30
16
8
100%
90%
I @ 30 ns
I @ 60 ns
10%
tP = 0.7 ns to 1 ns
Figure 9. IEC61000−4−2 Spec
ESD Gun
Oscilloscope
TVS
50 W
Cable
50 W
Figure 10. Diagram of ESD Clamping Voltage Test Setup
The following is taken from Application Note
AND8308/D − Interpretation of Datasheet Parameters
for ESD Devices.
systems such as cell phones or laptop computers it is not
clearly defined in the spec how to specify a clamping voltage
at the device level. ON Semiconductor has developed a way
to examine the entire voltage waveform across the ESD
protection diode over the time domain of an ESD pulse in the
form of an oscilloscope screenshot, which can be found on
the datasheets for all ESD protection diodes. For more
information on how ON Semiconductor creates these
screenshots and how to interpret them please refer to
AND8307/D.
ESD Voltage Clamping
For sensitive circuit elements it is important to limit the
voltage that an IC will be exposed to during an ESD event
to as low a voltage as possible. The ESD clamping voltage
is the voltage drop across the ESD protection diode during
an ESD event per the IEC61000−4−2 waveform. Since the
IEC61000−4−2 was written as a pass/fail spec for larger
www.onsemi.com
4
25
−25
20
−20
TLP CURRENT (A)
TLP CURRENT (A)
ESD7361, SZESD7361
15
10
−15
−10
−5
5
0
0
0
NOTE:
5
10
15
20
25
30
35
40
0
−2
−4
−6
−8
−10
−12
VC, VOLTAGE (V)
VC, VOLTAGE (V)
Figure 11. Positive TLP I−V Curve
Figure 12. Negative TLP I−V Curve
−14
TLP parameter: Z0 = 50 W, tp = 100 ns, tr = 300 ps, averaging window: t1 = 30 ns to t2 = 60 ns. VIEC is the equivalent voltage
stress level calculated at the secondary peak of the IEC 61000−4−2 waveform at t = 30 ns with 2 A/kV. See TLP description
below for more information.
Transmission Line Pulse (TLP) Measurement
L
Transmission Line Pulse (TLP) provides current versus
voltage (I−V) curves in which each data point is obtained
from a 100 ns long rectangular pulse from a charged
transmission line. A simplified schematic of a typical TLP
system is shown in Figure 13. TLP I−V curves of ESD
protection devices accurately demonstrate the product’s
ESD capability because the 10s of amps current levels and
under 100 ns time scale match those of an ESD event. This
is illustrated in Figure 14 where an 8 kV IEC 61000−4−2
current waveform is compared with TLP current pulses at
8 A and 16 A. A TLP I−V curve shows the voltage at which
the device turns on as well as how well the device clamps
voltage over a range of current levels.
50 W Coax
Cable
S Attenuator
÷
50 W Coax
Cable
10 MW
IM
VM
DUT
VC
Oscilloscope
Figure 13. Simplified Schematic of a Typical TLP
System
Figure 14. Comparison Between 8 kV IEC 61000−4−2 and 8 A and 16 A TLP Waveforms
www.onsemi.com
5
ESD7361, SZESD7361
ORDERING INFORMATION
Package
Shipping†
ESD7361HT1G
SOD−323
(Pb−Free)
3000 / Tape & Reel
ESD7361XV2T1G
SOD−523
(Pb−Free)
3000 / Tape & Reel
ESD7361P2T5G
SOD−923
(Pb−Free)
8000 / Tape & Reel
SZESD7361HT1G
SOD−323
(Pb−Free)
3000 / Tape & Reel
SZESD7361XV2T1G
SOD−523
(Pb−Free)
3000 / Tape & Reel
SZESD7361P2T5G
SOD−923
(Pb−Free)
8000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
6
ESD7361, SZESD7361
PACKAGE DIMENSIONS
SOD−323
CASE 477−02
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. LEAD THICKNESS SPECIFIED PER L/F DRAWING
WITH SOLDER PLATING.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
5. DIMENSION L IS MEASURED FROM END OF RADIUS.
HE
D
b
1
2
E
MILLIMETERS
DIM MIN
NOM MAX
A
0.80
0.90
1.00
A1 0.00
0.05
0.10
A3
0.15 REF
b
0.25
0.32
0.4
C 0.089
0.12 0.177
D
1.60
1.70
1.80
E
1.15
1.25
1.35
L
0.08
HE
2.30
2.50
2.70
A3
A
C
NOTE 3
L
NOTE 5
A1
SOLDERING FOOTPRINT*
0.63
0.025
0.83
0.033
1.60
0.063
2.85
0.112
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
7
INCHES
NOM MAX
0.035 0.040
0.002 0.004
0.006 REF
0.010 0.012 0.016
0.003 0.005 0.007
0.062 0.066 0.070
0.045 0.049 0.053
0.003
0.090 0.098 0.105
MIN
0.031
0.000
ESD7361, SZESD7361
PACKAGE DIMENSIONS
SOD−523
CASE 502
ISSUE E
−X−
D
NOTES:
6. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
7. CONTROLLING DIMENSION: MILLIMETERS.
8. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH.
MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF
BASE MATERIAL.
9. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS.
−Y−
E
2X
b
0.08
1
M
2
X Y
DIM
A
b
c
D
E
HE
L
L2
TOP VIEW
A
c
HE
RECOMMENDED
SOLDERING FOOTPRINT*
SIDE VIEW
2X
2X
0.48
L
L2
BOTTOM VIEW
1.80
2X
0.40
PACKAGE
OUTLINE
2X
MILLIMETERS
MIN
NOM
MAX
0.50
0.60
0.70
0.25
0.30
0.35
0.07
0.14
0.20
1.10
1.20
1.30
0.70
0.80
0.90
1.50
1.60
1.70
0.30 REF
0.15
0.20
0.25
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
8
ESD7361, SZESD7361
PACKAGE DIMENSIONS
SOD−923
CASE 514AB
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH.
MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF
BASE MATERIAL.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS.
−X−
D
−Y−
E
1
2X b
0.08 X Y
2
DIM
A
b
c
D
E
HE
L
L2
TOP VIEW
A
c
MILLIMETERS
MIN
NOM MAX
0.34
0.37
0.40
0.15
0.20
0.25
0.07
0.12
0.17
0.75
0.80
0.85
0.55
0.60
0.65
0.95
1.00
1.05
0.19 REF
0.05
0.10
0.15
SOLDERING FOOTPRINT*
HE
SIDE VIEW
1.20
2X
2X
2X
0.36
L
PACKAGE
OUTLINE
2X
INCHES
MIN
NOM MAX
0.013 0.015 0.016
0.006 0.008 0.010
0.003 0.005 0.007
0.030 0.031 0.033
0.022 0.024 0.026
0.037 0.039 0.041
0.007 REF
0.002 0.004 0.006
L2
0.25
DIMENSIONS: MILLIMETERS
See Application Note AND8455/D for more mounting details
BOTTOM VIEW
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
◊
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ESD7361/D
Similar pages