FEC60 SERIES 60 WATTS DC-DC CONVERTER FEATURES • 60 WATTS MAXIMUM OUTPUT POWER • SINGLE OUTPUT UP TO 14A • STANDARD 2.0 X 2.0 X 0.4 INCH PACKAGE • HIGH EFFICIENCY UP TO 90% • 2:1 WIDE INPUT VOLTAGE RANGE • SIX-SIDED CONTINUOUS SHIELD • FIXED SWITCHING FREQUENCY • APPROVED FOR BASIC INSULATION • NO MINIMUM LOAD REQUIRED • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Measurement Equipment Semiconductor Equipment OPTIONS Negative logic Remove On/Off DESCRIPTION The FEC60 series offer 60 watts of output power from a 2.00 x 2.00 x 0.4 inch package. The FEC60 series with 2:1 wide input voltage of 18~36VDC and 36~75VDC and features 1600VDC of isolation, short-circuit and over-voltage protection. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted INPUT SPECIFICATIONS OUTPUT SPECIFICATIONS Output power 60 Watts, max. Voltage accuracy ± 1% Minimum load 0% Voltage adjustability (Note 6) 24Vout + 20% -10% Others ±10% Line regulation LL to HL at Full Load Load regulation No Load to Full Load Ripple and noise 20MHz bandwidth ± 0.2% ± 0.5% See table Temperature coefficient Transient response 25% load step change recovery time 3.3VDC output 5VDC output Over voltage protection 12VDC output (Voltage clamped) 15VDC output 24VDC output Over load protection % of FL at nominal input Short circuit protection ±0.02% / ºC, max. 250µs 3.7VDC~5.4VDC 5.6VDC~7.0VDC 13.8VDC~17.5VDC 16.8VDC~20.5VDC 30.0VDC~33.0VDC 150%, max. Continuous, automatics recovery Input to Output Input(Output) to Case Case grounding Isolation resistance 500VDC Isolation capacitance Switching frequency Safety approvals Case material Input surge voltage 24VDC input 48VDC input Input reflected ripple 20mAp-p current Power up 20ms, max. Nominal input and Start up time constant resistive load Remote ON/OFF 20ms, max. 24VDC input 17VDC Start-up voltage 48VDC input 34VDC 24VDC input 15VDC Shutdown voltage 48VDC input 32VDC Remote ON/OFF (Note 7) Positive logic (standard) DC-DC ON Open or 3V < Vr < 12V DC-DC OFF Short or 0V < Vr < 1.2V DC-DC ON Short or 0V < Vr < 1.2V Negative logic (option) DC-DC OFF Open or 3V < Vr < 12V Input current of Remote control pin Nominal input -0.5mA~1.0mA Remote off state input current Nominal input 4mA ENVIRONMENTAL SPECIFICATIONS -40ºC ~ +40ºC (without derating) +40ºC ~ +110ºC (with derating) +110ºC -55ºC ~ +125ºC +120ºC 10.5ºC/Watt 8.4ºC/Watt MIL-STD-810F Without Heat-sink With Heat-sink Thermal shock 300kHz±10% Vibration IEC60950-1, UL60950-1, & EN60950-1 Relative humidity Nickel-coated copper EMC CHARACTERISTICS MIL-STD-810F 5% to 95% RH FR4 PCB Potting material Dimensions Weight MIL-HDBK-217F EMI (Note 10) EN55022 Epoxy (UL94 V-0) EN61000-4-2 2.00 X 2.00 X 0.40 Inch ESD (50.8 X 50.8 X 10.2 mm) Radiated immunity EN61000-4-3 60g (2.11oz) Fast transient (Note 11) EN61000-4-4 4.089 x 105 hrs Surge (Note 11) EN61000-4-5 Conducted immunity Page 1 of 3 18 ~ 36VDC 36 ~ 75VDC Pi type 50VDC 100ms, max. 100VDC 100ms, max. Input filter See table Maximum case temperature 1600 VDC, min. 1minute 1600 VDC, min. 1minute Storage temperature range Connect case to -INPUT Over temperature protection with decoupling Y Cap 9 10 ohms, min. Thermal impedance (Note 9) 1500pF, max. Base material MTBF (Note 1) 24VDC nominal input 48VDC nominal input Operating ambient temperature (Note8) GENERAL SPECIFICATIONS Efficiency Isolation voltage (Basic insulation) Input voltage range www.pduke.com EN61000-4-6 Class A, Class B Air Contact ± 8kV ± 6kV Perf. Criteria A 10 V/m Perf. Criteria A ± 2kV Perf. Criteria A ± 1kV Perf. Criteria A 10 Vr.m.s Perf. Criteria A 2014/4/30 FEC60 SERIES 60 WATTS Model Number Input Range Output Voltage FEC60-24S3P3 FEC60-24S05 FEC60-24S12 FEC60-24S15 FEC60-24S24 FEC60-48S3P3 FEC60-48S05 FEC60-48S12 FEC60-48S15 FEC60-48S24 18 ~ 36 VDC 18 ~ 36 VDC 18 ~ 36 VDC 18 ~ 36 VDC 18 ~ 36 VDC 36 ~ 75 VDC 36 ~ 75 VDC 36 ~ 75 VDC 36 ~ 75 VDC 36 ~ 75 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 24VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 24VDC DC-DC CONVERTER (2) (3) (4) Output Current Output No load Eff Min. load Full load Ripple & Noise Input Current (%) 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 0mA 14000mA 12000mA 5000mA 4000mA 2500mA 14000mA 12000mA 5000mA 4000mA 2500mA 75mVp-p 75mVp-p 100mVp-p 100mVp-p 200mVp-p 75mVp-p 75mVp-p 100mVp-p 100mVp-p 200mVp-p 100mA 130mA 50mA 50mA 50mA 80mA 90mA 30mA 30mA 30mA 89 90 90 90 89 89 90 90 90 89 (5) Capacitor Load max 36000µF 20400µF 3550µF 2300µF 885µF 36000µF 20400µF 3550µF 2300µF 885µF Note 1. 2. 3. 4. 5. 6. MIL-HDBK-217F @Tc=70 ºC, Full load. Typical value at nominal input and full load. (20MHz BW.) Typical value at nominal input and no load. Typical value at nominal input and full load. Test by minimum input and constant resistive load. 24VDC output maximum output deviation is +20%,-10% inclusive of remote sense and trim. Others maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +SENSE should be connected to its corresponding +OUTPUT and likewise the -SENSE should be connected to its corresponding –OUTPUT. 7. The CTRL pin voltage is referenced to -INPUT. To order negative logic ON/OFF control add the suffix-N (Ex: FEC60-48S05-N). 8. Test condition with vertical direction by natural convection. 9. Heat-sink is optional and P/N：7G-0026C-F. 10. The FEC60 series standard module meets EN55022 Class A and Class B with external components. For more detail information, please contact with P-DUKE. 11. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. FEC60-48S05 Derating Curve FEC60-48S05 Derating Curve With Heat-sink(Note 9) FEC60-48S05 Efficiency VS Input Volyage FEC60-48S05 Efficiency VS Output Load Page 2 of 3 www.pduke.com 2014/4/30 FEC60 SERIES 60 WATTS MECHANICAL DRAWING DC-DC CONVERTER ： 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) PIN CONNECTION PIN 1 2 3 4 5 6 7 8 Page 3 of 3 EXTERNAL OUTPUT TRIMMING SINGLE +INPUT -INPUT CTRL -SENSE +SENSE +OUTPUT -OUTPUT TRIM Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 4 8 RU 8 www.pduke.com RD 5 2014/4/30