CREE CGHV1F006S-AMP1 6 w, dc - 18 ghz, 40v, gan hemt Datasheet

CGHV1F006S
6 W, DC - 18 GHz, 40V, GaN HEMT
Cree’s CGHV1F006S is an unmatched, gallium nitride (GaN) high electron mobility transistor
(HEMT) designed specifically for high efficiency, high gain and wide bandwidth capabilities.
The device can be deployed for L, S, C, X and Ku-Band amplifier applications. The datasheet
specifications are based on a C-Band (5.5 - 6.5 GHz) amplifier. Additional application
circuits are available for C-Band at 5.8 GHz - 7.2 GHz and X-Band at 7.9 - 8.4 GHz and 8.5 9.6 GHz. The CGHV1F006S operates on a 40 volt rail circuit while housed in a 3mm x 4mm,
surface mount, dual-flat-no-lead (DFN) package. Under reduced power, the transistor can
Package Type
: 3x4 DFN
PN: CGHV1F0
06S
operate below 40V to as low as 20V VDD, maintaining high gain and efficiency.
Typical Performance 5.5-6.5 GHz (TC = 25˚C) , 40 V
Parameter
5.5 GHz
6.0 GHz
6.5 GHz
Units
Small Signal Gain
15.4
16.5
17.8
dB
Output Power @ PIN = 28 dBm
38.6
39.3
39.0
dBm
55
57
52
%
Drain Efficiency @ PIN = 28 dBm
Note:
Measured in the CGHV1F006S-AMP application circuit. Pulsed 100 µs 10% duty.
ary
Rev 2.2 – Janu
2016
Features for 40 V in CGHV1F006S-AMP
•
Up to 18 GHz Operation
•
8 W Typical Output Power
•
17 dB Gain at 6.0 GHz
•
15 dB Gain at 9.0 GHz
•
Application circuits for 5.8 - 7.2 GHz, 7.9 - 8.4 GHz, and 8.5 - 9.6 GHz.
•
High degree of APD and DPD correction can be applied
Listing of Available Hardware Application Circuits / Demonstration Circuits
Application Circuit
Operating Frequency
Amplifier Class
Operating Voltage
CGHV1F006S-AMP1
5.85 - 7.2 GHz
Class A/B
40 V
CGHV1F006S-AMP2
7.9 - 8.4 GHz
Class A/B
40 V
CGHV1F006S-AMP3
8.5 - 9.6 GHz
Class A/B
40 V
CGHV1F006S-AMP4
4.9 - 5.9 GHz
Class A/B
20 V
Subject to change without notice.
www.cree.com/rf
1
Absolute Maximum Ratings (not simultaneous) at 25˚C Case Temperature
Parameter
Symbol
Rating
Units
Notes
Drain-Source Voltage
VDSS
100
Volts
25˚C
Gate-to-Source Voltage
VGS
-10, +2
Volts
25˚C
Storage Temperature
˚C
TSTG
-65, +150
Operating Junction Temperature
TJ
225
˚C
Maximum Forward Gate Current
IGMAX
1.2
mA
25˚C
Maximum Drain Current
IDMAX
0.95
A
25˚C
Soldering Temperature2
TS
245
˚C
TC
-40, +150
˚C
RθJC
14.5
˚C/W
1
Case Operating Temperature3,4
Thermal Resistance, Junction to Case
5
85˚C
Note:
1
Current limit for long term, reliable operation
2
Refer to the Application Note on soldering at www.cree.com/rf/document-library
3
Simulated at PDISS = 2.4 W
4
TC = Case temperature for the device. It refers to the temperature at the ground tab underneath the package. The PCB will add additional thermal
resistance.
5
The RTH for Cree’s application circuit, CGHV1F006S-AMP, with 31 (Ø11 mil) via holes designed on a 20 mil thick Rogers 5880 PCB, is 3.9°C/W. The total RTH
from the heat sink to the junction is 14.5°C/W + 3.9°C/W = 18.4°C/W.
Electrical Characteristics (TC = 25˚C) - 40 V Typical
Characteristics
Symbol
Min.
Typ.
Max.
Units
Conditions
Gate Threshold Voltage
VGS(th)
-3.6
-3.0
-2.4
VDC
VDS = 10 V, ID = 1.2 mA
Gate Quiescent Voltage
VGS(Q)
–
-2.7
–
VDC
VDS = 40 V, ID = 60 mA
Saturated Drain Current2
IDS
–
-1.0
–
A
VDS = 6.0 V, VGS = 2.0 V
V(BR)DSS
100
–
–
VDC
VGS = -8 V, ID = 1.2 mA
DC Characteristics1
Drain-Source Breakdown Voltage
RF Characteristics3 (TC = 25˚C, F0 = 6.0 GHz unless otherwise noted)
Gain
G
–
16
-
dB
VDD = 40 V, IDQ = 60 mA, PIN = 0 dBm
POUT
–
38.5
–
dBm
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
η
–
55
-
%
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
VSWR
-
10 : 1
-
Y
No damage at all phase angles,
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
Input Capacitance5
CGS
–
1.3
–
pF
VDS = 40 V, Vgs = -8 V, f = 1 MHz
Output Capacitance5
CDS
–
0.31
–
pF
VDS = 40 V, Vgs = -8 V, f = 1 MHz
Feedback Capacitance
CGD
–
0.04
–
pF
VDS = 40 V, Vgs = -8 V, f = 1 MHz
Output Power4
Drain Efficiency4
Output Mismatch Stress4
Dynamic Characteristics
Notes:
1
Measured on wafer prior to packaging
2
Scaled from PCM data
3
Measured in CGHV1F006S-AMP
4
Pulsed 100 µs, 10% duty cycle
5
Includes package
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
2
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Electrical Characteristics When Tested in CGHV1F006S-AMP1 at C-Band Under OQPSK
Characteristics
Symbol
Min.
Typ.
Max.
Units
Conditions
RF Characteristics1 (TC = 25˚C, F0 = 5.8 - 7.2 GHz unless otherwise noted)
Gain
G
–
17.5
-
dB
VDD = 40 V, IDQ = 60 mA, PIN = 0 dBm
POUT
–
39
–
dBm
VDD = 40 V, IDQ = 60 mA, PIN = 27 dBm
η
–
55
-
%
VDD = 40 V, IDQ = 60 mA, PIN = 27 dBm
OQPSK3
ACLR
-
-36
-
dBc
VDD = 40 V, IDQ = 60 mA, POUT = 33 dBm
Output Mismatch Stress2
VSWR
–
10 : 1
–
Y
Output Power2
Drain Efficiency2
No damage at all phase angles,
VDS = 40 V, Vgs = -8 V, PIN = 27 dBm
Notes:
1
Measured in CGHV1F006S-AMP1 Application Circuit
2
Pulsed 100 µs, 10% duty cycle
3
OQPSK modulated signal, 1.6 msps, PN23, Alpha Filter = 0.2 Offset = 1.6 MHz
Typical Performance - CGHV1F006S-AMP1 at C-Band Under OQPSK
Figure 1. - Typical Small Signal Response of CGHV1F006S-AMP1 Application Circuit
VDD = 40 V, IDQ = 60 mA
30
20
Magnitude (dB)
10
0
-10
-20
S11
S21
S22
-30
5.0
5.5
6.0
6.5
Frequency (GHz)
7.0
7.5
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
3
CGHV1F006S Rev 2.2
8.0
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP1
Figure 2. - Typical Gain, Efficiency and OQPSK Performance vs Frequency
POUT = 33 dBm.
VDDPerformance
= 40 V, IDQ =at60
mA
CGHV1F006S
OQPSK
33dBm
40
0
Efficiency
Gain (dB) and Efficiency (%)
-5
Efficiency
Efficiency
Offset
30
-10
25
-15
20
-20
Gain
Gain
15
-25
10
-30
OQPSK Offset (dBc)
Gain
35
Offset Offset
5
0
-35
5.8
6.0
6.2
6.4
6.6
Frequency (GHz)
6.8
7.0
7.2
-40
CGHV1F006S OQPSK Transfer @ 7.2GHz
Figure 3. - Typical Gain, Efficiency and OQPSK Performance vs Input Power OQPSK Transfer
Frequency = 7.2 GHz, VDD = 40 V, IDQ = 60 mA
35
-15
DEff
30
-20
Gain_
-Oset_
-25
+Oset_
Efficiency
20
-30
Gain
15
-35
10
-40
Oset
5
0
OQPSK Offset (dBc)
Gain (dB)
Efficiency (%)
25
-45
10
15
20
25
30
35
-50
Input Power (dBm)
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
4
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP1
40.0
75
39.5
70
39.0
65
38.5
60
38.0
55
37.5
50
37.0
45
Drain Efficiency (%)
Output Power (dBm)
Figure 4. - Typical Pulsed Power Response
VDD = 40 V, IDQ = 60 mA, 100 µs, 10% Duty, PIN = 27 dBm
Output Power
36.5
36.0
5.70
Drain Efficiency
5.90
6.10
6.30
6.50
6.70
6.90
7.10
40
35
7.30
Frequency (GHz)
CGHV1F006S-AMP1 Application Circuit
Bill of Materials, OQPSK
Designator
Description
CGHV1F006S-AMP1 Application Circuit
Qty
R1
RES, 15, OHM, +1/-1%, 1/16 W, 0402
1
R2
RES, 100, OHM, +1/-1%, 1/16 W, 0603
1
C1, C14
CAP, 1.8 pF, ±0.1 pF, 0402, ATC
2
C2
CAP, 2.0 pF, ±0.1 pF, 0402, ATC
1
C3, C8
CAP, 1.5 pF, ±0.1 pF, 0402, ATC
2
CAP, 10 pF, ±5%, 0603, ATC
1
C5, C10
CAP, 470 pF, 5%, 100 V, 0603, X
2
C6, C11
CAP, 33000 pF, 0805, 100V, X7R
2
C7
CAP, 10 UF, 16 V, TANTALUM
1
C4
C9
CAP, 20 pF, ±5%, 0603, ATC
1
C12
CAP, 1.0 UF, 100V, 10% X7R, 1210
1
C13
CAP, 33 UF, 20%, G CASE
1
CONN, SMA, PANEL MOUNT JACK, FLANGE
2
PCB, RT5880, 0.020” THK, CGHV1F006S
1
J3
HEADER RT>PLZ .1CEN LK 5POS
1
Q1
QFN TRANSISTOR CGHV1F006S
1
J1, J2
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
5
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
CGHV1F006S-AMP1 Application Circuit Schematic, OQPSK
Vg=-2.0V to -3.5V typ
GND
Vd=+40V
5
C7
10
C6
0.033
C5
470 pF
C4
10 pF
R2
100 Ohm
C1
1.8 pF
4
3
2
1
J3
C8
C9
C11
C10
1.5 pF 20 pF 470 pF 0.033
C3
1.5 pF
C12
1
C13
33
C14
1.8 pF
R1
15 Ohm
Q1 2
J2
1
J1
C2
2.0 pF
3
CGHV1F006S-AMP1 Application Circuit Outline, OQPSK
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
6
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Electrical Characteristics When Tested in CGHV1F006S-AMP2 at X-Band, SATCOM
Characteristics
Symbol
Min.
Typ.
Max.
Units
Conditions
RF Characteristics1 (TC = 25˚C, F0 = 7.9 - 8.4 GHz unless otherwise noted)
Gain
G
–
15
-
dB
VDD = 40 V, IDQ = 60 mA, PIN = 0 dBm
POUT
–
39
–
dBm
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
η
–
55
-
%
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
OQPSK3
ACLR
-
-37
-
dBc
Output Mismatch Stress2
VSWR
–
10 : 1
–
Y
Output Power2
Drain Efficiency2
VDD = 40 V, IDQ = 60 mA, POUT = 33 dBm
No damage at all phase angles,
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
Notes:
1
Measured in CGHV1F006S-AMP2 Application Circuit
2
Pulsed 100 µs, 10% duty cycle
3
OQPSK modulated signal, 1.6 msps, PN23, Alpha Filter = 0.2 Offset = 1.6 MHz
Typical Performance in Application Circuit CGHV1F006S-AMP2 at X-Band, SATCOM
Figure 5. - Typical Small Signal Response of CGHV1F006S-AMP2 Application Circuit
VDD = 40 V, IDQ = 60 mA
30
20
Magnitude (dB)
10
0
-10
S21
-20
S11
S22
-30
7.0
7.2
7.4
7.6
7.8
8.0
8.2
8.4
8.6
8.8
9.0
Frequency (GHz)
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
7
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP2
Figure 6. - Typical OQPSK Response
VDD = 40 V, IDQ = 60 mA, 1.6 MSPS, POUT = 33 dBm
40
-30
35
-31
POUT
30
-32
Gain
25
-33
Drain Efficiency
20
-34
ACLR
Gain
15
ACLR (dBc)
Gain (dB) & Drain Efficiency (%)
Drain Efficiency
-35
10
-36
ACLR
5
-37
0
7.90
7.95
8.00
8.05
8.10
8.15
8.20
8.25
8.30
8.35
-38
8.40
Frequency (GHz)
Typical Performance in Application Circuit CGHV1F006S-AMP2
35
Figure 7. - OQPSK Transfer Response
VDD = 40 V, IDQ = 60 mA, 1.6 MSPS, Frequency = 8.4 GHz
-10
Gain
30
-15
Eff
+Oset
-20
20
-25
15
-30
10
-35
5
-40
0
15
20
25
30
Output Power (dBm)
35
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
8
CGHV1F006S Rev 2.2
40
OQPSK Offset (dBc)
Gain (dB) and Drain Efficiency (%)
-Oset
25
-45
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP2
Figure 8. - Typical Pulsed Power Response
VDD = 40 V, IDQ = 60 mA, 100 µs, 10% Duty, PIN = 28 dBm
40.0
75
Output Power
39.5
70
65
38.5
38.0
55
37.5
50
37.0
45
Output Power
36.5
36.0
7.80
Drain
Efficiency
7.90
8.00
8.10
8.20
Frequency (GHz)
CGHV1F006S-AMP2 Application Circuit
Bill of Materials, SATCOM
Designator
Description
RES, 15, OHM, +1/-1%, 1/16 W, 0402
1
RES, 100, OHM, +1/-1%, 1/16 W, 0603
1
CAP, 1.0 pF, ±0.05 pF, 0402, ATC
3
CAP, 10 pF, ±5%, 0603, ATC
2
CAP, 10pF, ±5%, 0603, X
1
C5,C10
CAP, 470pF, 5%, 100V, 0603, X
2
C6, C11
C4
CAP, 33000 pF, 0805, 100V, X7R
2
C7
CAP, 10 UF, 16 V, TANTALUM
1
C9
CAP, 20 pF, ±5%, 0603, ATC
1
C12
CAP, 1.0 UF, 100V, 10% X7R, 1210
1
C13
CAP, 33 UF, 20%, G CASE
1
CONN, SMA, PANEL MOUNT JACK, FLANGE
2
J3
HEADER RT>PLZ .1CEN LK 5POS
1
Q1
QFN TRANSISTOR CGHV1F006S
1
J1, J2
8.40
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
9
CGHV1F006S Rev 2.2
35
8.50
Qty
R2
C1, C14
8.30
40
CGHV1F006S-AMP2 Application Circuit
R1
C2, C3, C8
60
Drain Efficiency
Drain Efficiency (%)
Output Power (dBm)
39.0
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
CGHV1F006S-AMP2 Application Circuit Schematic, SATCOM
Vg=-2.0V to -3.5V typ
GND
Vd=+40V
5
C7
10
C6
0.033
C5
470 pF
C4
10 pF
R2
100 Ohm
4
3
2
1
J3
C8
C9
C11
C10
1.0 pF 20 pF 470 pF 0.033
C3
1.0 pF
C13
33
C14
1.0 pF
R1
15 Ohm
C1
1.0 pF
C12
1
Q1 2
J2
1
J1
C2
1.0 pF
3
CGHV1F006S-AMP2 Application Circuit Outline, SATCOM
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
10
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Electrical Characteristics When Tested in CGHV1F006S-AMP3 at X-Band, RADAR
Characteristics
Symbol
Min.
Typ.
Max.
Units
Conditions
RF Characteristics1 (TC = 25˚C, F0 = 8.5 - 9.6 GHz unless otherwise noted)
Gain
Output Power2
Drain Efficiency2
Output Mismatch Stress2
G
–
14.5
-
dB
VDD = 40 V, IDQ = 60 mA, PIN = 0 dBm
POUT
–
38.5
–
dBm
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
η
–
52
-
%
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
VSWR
–
10 : 1
–
Y
VDD = 40 V, IDQ = 60 mA, PIN = 28 dBm
Notes:
1
Measured in CGHV1F006S-AMP3 Application Circuit
2
Pulsed 100 µs, 10% duty cycle
Typical Performance in Application Circuit CGHV1F006S-AMP3 at X-Band, RADAR
Figure 9. - Typical Small Signal Response
VDD = 40 V, IDQ = 60 mA
30
20
Magnitude (dB)
10
0
-10
-20
S21
S11
S22
-30
7.5
8.0
8.5
9.0
Frequency (GHz)
9.5
10.0
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
11
CGHV1F006S Rev 2.2
10.5
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP3
Figure 10. - Typical Pulsed Power Response
VDD = 40 V, IDQ = 60 mA, 100 µs, 10% Duty, PIN = 28 dBm
40.0
75
39.5
70
65
Output Power
38.5
60
38.0
55
Drain Efficiency
37.5
50
37.0
45
36.5
Drain Efficiency (%)
Output Power (dBm)
39.0
40
Output Power
Drain Efficiency
36.0
8.4
8.6
8.8
9.0
Frequency (GHz)
CGHV1F006S-AMP3 Application Circuit
Bill of Materials, RADAR
9.2
9.4
9.6
35
CGHV1F006S-AMP3 Application Circuit
Designator
Description
Qty
R1
RES, 15, OHM, +1/-1%, 1/16 W, 0402
1
R2
RES, 100, OHM, +1/-1%, 1/16 W, 0603
1
C1, C14
CAP, 1.0 pF, ±0.05 pF, 0603, ATC
2
C2
CAP, 1.0 pF, ±0.05 pF, 0402, ATC
1
C3, C8
CAP, 0.8 pF, ±0.05 pF, 0402, ATC
2
CAP, 10 pF, ±5%, 0603, ATC
1
C5, C10
CAP, 470 pF, 5%, 100 V, 0603, X
2
C6, C11
C4
CAP, 33000 pF, 0805, 100V, X7R
2
C7
CAP, 10 UF, 16 V, TANTALUM
1
C9
CAP, 20 pF, ±5%, 0603, ATC
1
C12
CAP, 1.0 UF, 100V, 10% X7R, 1210
1
C13
CAP, 33 UF, 20%, G CASE
1
J1, J2
CONN, SMA, PANEL MOUNT JACK, FLANGE
2
J3
HEADER RT>PLZ .1CEN LK 5POS
1
Q1
QFN TRANSISTOR CGHV1F006S
1
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
12
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
CGHV1F006S-AMP3 Application Circuit Schematic, RADAR
Vg=-2.0V to -3.5V typ
GND
Vd=+40V
5
C7
10
C6
0.033
C5
470 pF
C4
10 pF
R2
100 Ohm
C1
1.0 pF
4
3
2
1
J3
C8
C9
C11
C10
0.8 pF 20 pF 470 pF 0.033
C3
0.8 pF
C12
1
C13
33
C14
1.0 pF
R1
15 Ohm
Q1 2
J2
1
J1
C2
1.0 pF
3
CGHV1F006S-AMP3 Application Circuit Outline, RADAR
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
13
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Electrical Characteristics When Tested in CGHV1F006S-AMP4 at 802.11
Characteristics
Symbol
Min.
Typ.
Max.
Units
Conditions
RF Characteristics1 (TC = 25˚C, F0 = 4.9 - 5.9 GHz unless otherwise noted)
Gain
G
–
13
-
dB
VDD = 20 V, IDQ = 30 mA, PIN = 27 dBm
Drain Efficiency2
η
–
27
-
%
VDD = 20 V, IDQ = 30 mA, PIN = 27 dBm
OQPSK3
ACLR
-
-43
-
dBc
VDD = 20 V, IDQ = 30 mA, POUT = 27 dBm
Output Mismatch Stress2
VSWR
–
10 : 1
–
Y
No damage at all phase angles,
VDD = 20 V, IDQ = 30 mA, PIN = 27 dBm
Notes:
1
Measured in CGHV1F006S-AMP4 Application Circuit
2
Single carrier WCDMA, 3GPP Test Model 1, G4 DPCH, 45% clipping, PAR = 7.5 dB @ 0.01% probability on CCDF
Typical Performance - CGHV1F006S-AMP4 at 802.11
Figure 11. - Typical Small Signal Response
VDD = 20 V, IDQ = 30 mA
30
20
Magnitude (dB)
10
0
-10
-20
S11
S21
S22
-30
4.0
4.5
5.0
5.5
Frequency (GHz)
6.0
6.5
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
14
CGHV1F006S Rev 2.2
7.0
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Typical Performance in Application Circuit CGHV1F006S-AMP4
Figure 12. - Typical Gain, Efficiency and WCDMA Performance vs Frequency
VDD = 20 V, IDQ = 30 mA, POUT = 27 dBm
40
-37
Gain
35
-38
Drain Efficiency
Drain Efficiency
ACLR
-39
25
-40
20
-41
ACLR
15
-42
Gain
10
-43
5
-44
0
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
ACLR (dBc)
Gain (dB) & Drain Efficiency (%)
30
-45
Frequency (GHz)
CGHV1F006S-AMP4 Application Circuit
Bill of Materials at 802.11
Designator
R1, R3
R2
Description
CGHV1F006S-AMP4 Application Circuit
Qty
RES, 1, OHM, +/-1%, 1/16 W, 0402
2
RES, 51.1, OHM, +/-1%, 1/16W, 0603
1
C2, C6, C11
CAP, 1.8 pF, +/-0.1 pF, 0603, ATC
3
C1
CAP, 0.2 pF, +/-0.05 pF, 0402, ATC
1
C3, C7, C12
CAP, 470 pF, 5%, 100 V, 0603, X
3
C4, C8, C13
CAP, 33000 pF, 0805, 100 V, X7R
3
C5
CAP, 10 UF, 16 V, TANTALUM
1
C15
CAP, 6.8 pF, ±0.25 pF, 100 V, 0603
1
C9, C14
CAP, 1.0 UF, 100V, 10% X7R, 1210
2
CAP, 33 UF, 20%, G CASE
1
CONN, SMA, PANEL MOUNT JACK, FLANGE
2
PCB, RT5880, 0.020” THK, CGHV1F006S
1
BASEPLATE, CGH35015, 2.60 X 1.7
1
HEADER RT>PLZ .1CEN LK 5POS
1
2-56 SOC HD SCREW 1/4 SS
4
#2 SPLIT LOCKWASHER SS
4
QFN TRANSISTOR CGHV1F006S
1
C10
J1, J2
J3
Q1
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
15
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
CGHV1F006S-AMP4 Application Circuit Schematic
Efficiency
Gain
Offset
CGHV1F006S-AMP4 Application Circuit Outline
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
16
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
CGHV1F006S Power Dissipation De-rating Curve
Figure 13. - CGHV1F006S Transient Power Dissipation De-Rating Curve
12
10
Power Dissipation (W)
8
Note 1
6
4
2
0
0
25
50
75
100
125
150
175
200
225
250
Maximum CaseTemperature ( C)
Note 1. Area exceeds Maximum Case Temperature (See Page 2).
Electrostatic Discharge (ESD) Classifications
Parameter
Symbol
Class
Test Methodology
Human Body Model
HBM
1A (> 250 V)
JEDEC JESD22 A114-D
Charge Device Model
CDM
2 (125 V to 250 V)
JEDEC JESD22 C101-C
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
17
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Source and Load Impedances
D
Z Source
Z Load
G
S
Frequency (GHz)
Z Source
Z Load
1
49.67 + j32.81
184.11 + j6.66
3
11.54 + j3.96
38.83 + j56.37
6
5.94 - j17.97
13.03 + j16.16
10
11.87 - j77.62
11.79 - j17.43
12
47.42 - j205.35
16.39 - j46.22
15
33.78 + j251.03
163.61 - j268.44
Note1: VDD = 40 V, IDQ = 60 mA
Note2: Impedances are extracted from source and load pull data derived from the transistor.
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
18
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Product Dimensions CGHV1F006S (Package 3 x 4 DFN)
Pin
Input/Output
1
GND
2
NC
3
RF IN
4
RF IN
5
NC
6
GND
7
GND
8
NC
9
RF OUT
10
RF OUT
11
NC
12
GND
Note: Leadframe finish for 3x4 DFN package is Nickel/Palladium/Gold. Gold is the outer layer.
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
19
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Part Number System
CGHV1F006S
Package
Power Output (W)
Upper Frequency (GHz)
Cree GaN High Voltage
Parameter
Upper Frequency
1
Value
Units
15.0
GHz
6
W
Surface Mount
-
Power Output
Package
Table 1.
Note1: Alpha characters used in frequency code
indicate a value greater than 9.9 GHz. See Table
2 for value.
Character Code
Code Value
A
0
B
1
C
2
D
3
E
4
F
5
G
6
H
7
J
8
K
9
Examples:
1A = 10.0 GHz
2H = 27.0 GHz
Table 2.
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
20
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Product Ordering Information
Order Number
Description
Unit of Measure
CGHV1F006S
GaN HEMT
Each
CGHV1F006S-AMP1
Test board with GaN HEMT installed,
5.85 - 7.2 GHz, 50 V
C-Band under OQPSK
Each
CGHV1F006S-AMP2
Test board with GaN HEMT installed,
7.9 - 8.4 GHz, 28 V
X-Band SATCOM
Each
CGHV1F006S-AMP3
Test board with GaN HEMT installed,
8.5 - 9.6 GHz, 28 V
X-Band RADAR
Each
CGHV1F006S-AMP4
Test board with GaN HEMT installed,
4.9 - 5.9 GHz, 50 V
802.11
Each
CGHV1F006S-TR
Delivered in Tape and Reel
250 parts / reel
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
21
CGHV1F006S Rev 2.2
Image
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Disclaimer
Specifications are subject to change without notice. Cree, Inc. believes the information contained within this data sheet to be accurate
and reliable. However, no responsibility is assumed by Cree for any infringement of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under any patent or patent rights of Cree. Cree makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose. “Typical” parameters are the average
values expected by Cree in large quantities and are provided for information purposes only. These values can and do vary in different
applications and actual performance can vary over time. All operating parameters should be validated by customer’s technical experts
for each application. Cree products are not designed, intended or authorized for use as components in applications intended for surgical
implant into the body or to support or sustain life, in applications in which the failure of the Cree product could result in personal injury or
death or in applications for planning, construction, maintenance or direct operation of a nuclear facility.
For more information, please contact:
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
www.cree.com/rf
Sarah Miller
Marketing
Cree, RF Components
1.919.407.5302
Ryan Baker
Marketing & Sales
Cree, RF Components
1.919.407.7816
Tom Dekker
Sales Director
Cree, RF Components
1.919.313.5639
Copyright © 2013 - 2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are
registered trademarks of Cree, Inc.
22
CGHV1F006S Rev 2.2
Cree, Inc.
4600 Silicon Drive
Durham, North Carolina, USA 27703
USA Tel: +1.919.313.5300
Fax: +1.919.869.2733
www.cree.com/rf
Similar pages