Cyrustek ES5 True rms-to-dc converter Datasheet

ES5
True RMS-to-DC Converter
Features
Description
True RMS-To-DC Conversion
 Computes RMS of AC and DC
Signals
 600mV full scale
 Wide Response:
The ES5 is a true RMS-to-DC converter. It
accepts low-level input signals from 0 to
600 mVRMS complex input waveforms. It
can be operated form either a single supply
or dual supplies. The device draws less
than 1.2 mA of quiescent supply current,
furthermore, a chip select pin is provided
to power-down mode of the device,
making it ideal for battery-powered
applications.

 1MHz 3dB Bandwidth for VRMS>
100mVRMS
Single or Dual Supply Operation
 Power Down Function:
Quiescent current reduction from
1.2mA to 5uA
 Buffered Voltage Output
 14-lead SOIC (150mil width)

Application
* Digital Multi-Meters
* Battery-Powered Instruments
* Panel Meter
Pin Assignment
BUFF IN
1
NC
2
COMMON
3
ES6
ES5
TOP VIEW
( Not to Scale )
14
BUFF OUT
13
VIN
12
NC
11
+VS
OUTPUTOFFSET
4
CS
5
10
- VS
DEN INPUT
6
9
RMS OUT
NC
7
8
CAV
NC = NO CONNECT
SOP 14Pin Package
Ver 1.1
1
14/10/21
ES5
True RMS-to-DC Converter
Pin Description
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Symbol
BUFF IN
NC
COMMON
OUTPUT OFFSET
CS
DEN INPUT
NC
CAV
RMS OUT
-Vs
+Vs
NC
VIN
BUFF OUT
Type
I
G
O
I
I
I/O
O
P
P
I
O
Description
Buffer Input
No Connection
Analog Common
Output Offset
Chip Select
Denominator Input
No Connection
Averaging Capacitor Connection
RMS Output
Negative Supply Rail
Positive Supply Rail
No Connection
Signal input
Buffer Output
Absolute Maximum Ratings
Supply Voltage:Dual Supplies ......…………………………………………….... ±6V
Single Supply ..………………………………….……...……..... +12V
Input Voltage:………………………………………………………….…………+Vs
Power Dissipation (Package) SOIC:………………………………….……….. 450mW
Operating Temperature Range:…………………… ……………….. -40℃ to +85℃
Storage Temperature Range:………………………………………… -55℃ to +150℃
Lead Temperature (Soldering, 10sec):…………………………………………... 300℃
Ver 1.1
2
14/10/21
ES5
True RMS-to-DC Converter
Electrical Characteristics
(TA= +25℃, Vs = +3V, -Vs = -3V, unless otherwise noted.)
PARAMETER
Transfer Equation
Averaging Time Constant
CONDITIONS
Figure 3
CONVERSION ACCURACY
Total Error, Internal Trim
(Notes 1,2)
Total Error vs. Temperature
(-40℃ to + 85℃)
MIN
TYP
Total Error vs. Supply
+VIN=300mV
- VIN=-300mV
30
100
DC Reversal Error
Vin= 600mV
±0.3
Total Error, External Trim
(Note 1)
Crest Factor 1 to 2
Crest Factor = 3
Crest Factor = 6
FREQUENCY RESPONSE (Note 2,4)
mVRMS
2.2
5.0
±3.0V Supplies
±5V Supplies
6
±0.5
VPK
KΩ
mV
TA=+25℃
±0.5
mV
TA =-40~85 ℃
±0.1
mV/℃
+3V, -3V Supplies
2.2
V
mA
mA
Ω
KΩ
5
18
Chip Select High
Chip Select Low
0.5
100
DENOMINATIOR INPUT
Input Range
Input Resistance
Offset Voltage
0 to 2
25
±0.2
BUFFER AMPLIFIER
Input and Output Voltage
Range
Input Offset Voltage
Input Current
Input Resistance
Output Current
Short-Circuit Current
Small-Signal Bandwidth
Slew Rate (Note 5)
Ver 1.1
±% of
Reading
mV ±% of
Reading
0 to 600
OUTPUT CHARACTERISTICS (Note 1)
Output Resistance
μV ±% of
KHz
KHz
KHz
KHz
MHz
MHz
Input Resistance
Input Offset Voltage
Output Voltage Swing
Output Current
Short-Circuit Current
mV ±% of
Reading
mV ±% of
Reading/℃
11
90
200
130
1
3
Continuous RMS, All Supplies
Offset Voltage (Vin=COM)
ms/μF CAV
±% of
Reading
INPUT CHARACTERISTICS
Peak Transient
UNITS
Specified Accuracy
±0.1
±0.5
VIN =10mV
Bandwidth for 1% Additional
VIN =100mV
Error (0.09dB)
VIN =600mV
VIN =10mV
±3dB Bandwidth
VIN =100mV
VIN =600mV
Input Signal range
±0.5
±1.0
±0.1
±0.01
150
300
±0.25
±0.1
ERROR vs. CREST FACTOR
Additional Error (Note 3)
MAX
VOUT = [avg.(VIN)2]1/2
25
V
kΩ
V
-Vs to (+Vs-1.8V)
±0.8
±50
108
20
1
5
3
V
±1.5
mV
nA
Ω
5
mA
mA
MHz
V/μs
14/10/21
ES5
True RMS-to-DC Converter
Electrical Characteristics (continued)
(TA= +25℃, Vs = +3V, -Vs = -3V, unless otherwise noted.)
PARAMETER
Power SUPPLY
CONDITIONS
Dual Supplies
Standby Current
MIN
TYP
±2.5
Connect CS to –Vs and Pin4 is connected
to COMMON (Figure.1).
Quiescent Current (Note 6)
1
MAX
UNITS
±6
V
2
μA
mA
Note 1: Accuracy is specified for 0 to 600mV, 1kHz sine-wave input. Accuracy is degraded at higher RMS signal levels.
Note 2: Measured at pin9 (RMS OUT), with pin 4 tied to COMMON.
Note 3: Error vs. crest factor is specified as an additional error for 300mVRMS rectangular pulse input, pulse width = 200μs.
Note 4: Input voltages are expressed in volts VRMS
Note 5: With 10 kΩ external pull-down resistor from pin 14 (BUFF OUT) to – Vs.
Note 6: With BUF input tied to COMMON.
Ver 1.1
4
14/10/21
ES5
True RMS-to-DC Converter
Standard Connection
The ES5 is simple to connect for a majority of rms measurements. In the standard rms
connection shown in Figure 1, only an external capacitor is required to set the
averaging time constant. In this configuration, the ES5 computes the True RMS value
of any input signal. The magnitude of an averaging error is dependent on the value of
the averaging capacitor, is existed at lower frequencies. For example, if the filter
capacitor, CAV, is 4.7μF, the error is 0.3% at 10Hz. To measure ac signal, the ES5 can be
ac-couples by adding a capacitor in series with the input, as shown in Figure 1.
The performance of the ES5 is tolerant of minor variations in the power supply voltages;
however, if the supplies used exhibit a considerable amount of high frequency ripple, it
is advisable to bypass both supplies to ground through a 0.1μF ceramic disc capacitor
places as close to the device as possible.
The output signal range of the ES5 is a function of the supply voltages, the output
signal can be used buffered or nonbuffered, depending on the characteristics of the load.
If no buffer is needed, tie the buffer input (Pin 1) to common. The output of the ES5 is
capable of driving 5mA into a 2KΩ load without degrading the accuracy of the device.
1
BUFF IN
2
NC
3
COMMON
4
OUTPUT
OFFSET
5
CS
6
DEN
INPUT
+ Vs
BUFF OUT
ABSOLUTE
VALUE
4.7K
7
ES6
ES5
+
-
14
VIN 13
22uF
VIN
NC 12
( OPTIONAL)
BIAS
SQUARER /
DIVIDER
+
+
+VS 11
+ Vs
- VS 10
- Vs
RMSOUT 9
+ CAV
CAV
NC
8
VOUT
4.7uF
Figure 1. Standard connection for ES5
Ver 1.1
5
14/10/21
ES5
True RMS-to-DC Converter
High-Accuracy Adjustments
The accuracy of the ES5 can be further improved by the external trimming scheme as
shown in Figure 2. The input should be grounded and R1 adjusted to give 0V output
offset from pin 9. Alternatively, R1 could be adjusted to give the correct output with the
lowest expected value of VIN. The R4 is in series with the pin13 to lower the range of
the scale factor. Connect the desired full scale to VIN by using a DC or AC signal (ex.
500mVRMS), and R3 is trimmed to give the correct value for a calibrated signal.
+ Vs
R2
R1
500K
+ Vs
- Vs
1
BUFF IN
2
NC
3
COMMON
4
OUTPUT
OFFSET
5
CS
6
DEN
INPUT
100K
4.7K
7
ES6
ES5
+
-
BUFF OUT
ABSOLUTE
VALUE
14
VIN 13
R4
150
VIN
NC 12
BIAS
SQUARER /
DIVIDER
+VS 11
- VS 10
+
+
NC
RMSOUT
+ Vs
- Vs
9
+ CAV
CAV
8
VOUT
4.7uF
R3 2K
SCALE FACTOR TRM
Figure 2. Optional External Gain and Offset Trims
Chip Select
The ES5 provides a chip select pin (Pin 5). To enable the device, this pin must be
connected to +Vs. If it is connected to –Vs or floated, the device will enter power-down
mode. The current it draws at this mode is less than 10uA. (Figure 1.)
Ver 1.1
6
14/10/21
ES5
True RMS-to-DC Converter
Choosing the Averaging Time Constant
The ES5 computes the RMS value of AC and DC signals. At low frequencies and DC,
the output tracks the input exactly; at higher frequencies, the average output approaches
the RMS value of the input signal. The actual output differs from the ideal by an
average (or DC) error plus some amount of ripple.
The DC error term is a function of the value of CAV and the input signal frequency. The
output ripple is inversely proportional to the value of CAV. Waveforms with high crest
factors, such as a pulse train with low duty cycle, should have an average time constant
chosen to be at least ten times the signal period.
Using a large value of CAV to remove the output ripple increases the setting time for a
step change in the input signal level.
The primary disadvantage in using a large CAV to remove ripple is that the settling time
for a step change in input level is increased proportionately. A better method to reduce
the settling time and ripple is to use a post filter. A suggested circuit is shown in Figure
3. The 1-pole or 2-pole filter configuration allows a smaller CAV. With post filter, the
value of CAV should be just large enough to give the maximum dc error at the lowest
frequency of interest. And the output ripple will be removed by the post filter.
1 BUFF IN
ES6
ES5
+
-
BUFF OUT
ABSOLUTE
VALUE
2 NC
3 COMMON
OUTPUT
4 OFFSET
+ Vs
DEN
6 INPUT
VIN 13
BUFF OUT
VIN
+
NC 12
C1
10uF
BIAS
SQUARER /
DIVIDER
+VS 11
5 CS
4.7K
14
- VS 10
+
+
RMSOUT
- Vs
9
+ CAV
CAV
7 NC
R1 24K
+ Vs
8
FOR A SINGLE-POLE
FILTERSHORT R1
AND REMOVE C1
VOUT
4.7uF
24K
+
10uF
Figure 3. 2-Pole Filter
Ver 1.1
7
14/10/21
ES5
True RMS-to-DC Converter
Packaging
1.14 Pin SOP Package
2. Dimension Paramenters
Ver 1.1
8
14/10/21
Similar pages