ZETTLER AZ2150W-1AE-9DFT 30 amp miniature power relay Datasheet

AZ2150W
30 AMP MINIATURE
POWER RELAY
RoHS compliant !
FEATURES
•
•
•
•
•
•
•
•
1.75 mm contact gap
DC coils up to 48V
High dielectric strength 4 kV contact to coil
All plastics PTI 250
Epoxy sealed versions available
UL Class F (155°C) standard
UL, CUR file E44211
VDE certificate 40023154
CONTACTS
GENERAL DATA
Arrangement
SPST (1 Form A)
Ratings
Resistive load:
Ratings
UL, CUR
VDE
Life Expectancy
Mechanical
Electrical
Minimum operations
2 x 105
3 x 104 at 30 A 250 VAC Res.
Max. switched power: 900 W or 8310 VA
Max. switched current: 30 A
Max. switched voltage: 250 VDC* or 440 VAC
Operate Time
15 ms max. at nominal coil voltage
Release Time
10 ms max. at nominal coil voltage
(with no coil suppression)
*Note: If switching voltage is greater than 30 VDC,
special precautions must be taken.
Please contact the factory.
Dielectric Strength
(at sea level for 1 min.)
3000 Vrms between open contacts
4000 Vrms contact to coil
Insulation Resistance
1000 megaohms min. at 20°C,
500 VDC 50% RH
Insulation
(according to
DIN VDE 0110,
IEC 60664-1)
C250
Overvoltage category: III
Pollution degree: 2
Nominal voltage: 250 VAC
Holding Voltage
Greater than 50% of nominal coil voltage
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature
Operating
-40°C (-40°F) to 85°C (185°F)
Vibration
1.5 mm DA at 10-55 Hz
Shock
10 g
Enclosure
P.B.T. polyester
30 A at 277 VAC, General use
20 A at 250 VAC, AC7a
Material
Silver tin oxide
Resistance
< 50 milliohm initially
(24 V, 1A voltage drop method)
COIL
Power
At Pickup Voltage
(typical)
625 mW
Max. Continuous
Dissipation
1.7 W at 20°C (68°F) ambient
Temperature Rise
43°C (77°F) at nominal coil voltage
Terminals
Tinned copper alloy, P.C.
155°C (311°F) Class F
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
1. All values at 20°C (68°F).
Max. Immersion Time
30 seconds
2. Relay may pull in with less than “Must Operate” value.
Weight
25 grams
3. Specifications subject to change without notice.
Packing unit in pcs
40 per plastic tray / 280 per carton
Max. Temperature
NOTES
4. If higher electrical loads are to be switched by the relay contacts,
the vent nib has to be opened prior to use of the relay.
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2015-03-31
AZ2150W
RELAY ORDERING DATA
COIL SPECIFICATIONS – DC Coil
Nominal Coil
VDC
5
Must Operate
VDC
3.75
Min. Holding
VDC
2.5
Max. Continuous
VDC
6.0
6
4.50
3.0
7.2
9
6.75
4.5
10.8
ORDER NUMBER*
Coil Resistance
Ohm ± 10%
22.5
AZ2150W–1AE–5DFT
32.5
AZ2150W–1AE–6DFT
73
AZ2150W–1AE–9DFT
12
9.0
6.0
14.4
130
AZ2150W–1AE–12DFT
24
18.0
12.0
38.8
520
AZ2150W–1AE–24DFT
48
36.0
24.0
57.6
2,080
AZ2150W–1AE–48DFT
* Substitute “DEFT” in place of “DFT” for epoxy sealed version.
Coils 5VDC, 6VDC, 48VDC not VDE approved.
MECHANICAL DATA
PC BOARD LAYOUT
.500 .400
(12.8) (10.2)
Vent nib. (Please pay attention to note 4 on page 1.)
2 x ø .079
(ø 2.0)
.020
.130 +– .010
+
0.51)
(3.3 – 0.25
1.25
(31.80)
.090
(2.3)
1.000
(25.4)
.500
(12.7)
.690
(17.5)
2 x ø .044
(ø 1.1)
1.06
(26.9)
.196
(5.0)
.150 (3.8)
.751
(19.1)
.550 (14.0)
.700
(17.8)
Viewed toward
terminals
WIRING DIAGRAM
.200
(5.1)
.045 x .045
(1.14 x 1.14)
.032 x .062
(0.81 x 1.57)
1 FORM A
(SPST-NO)
.025 x .025
(0.63 x 0.63)
Viewed toward
terminals
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP
Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2015-03-31
AZ2150W
Electrical life at 250 VAC, resistive load
Electrical life reduction factor at inductive AC load
107
F
1,0
Reduction factor
Number of cycles
0,9
106
0,8
0,7
0,6
0,5
105
0,4
0,3
1,0
0,9
0,8
0,7
0,6
0,5
0,4
0,3
cos j
0,2
Power factor
104
0
0,8
1,6
2,4
3,2
4,0
4,8
5,6
6,4
7,2
Ncos j = N x F
8,0
Breaking capacity [kVA]
Max. AC/DC resistive load breaking capacity
50
AC
Current [A]
30
10
5
2
DC
1
0,5
0,1
10
20
30
40 50
100
200
400
600
Voltage [V]
ZETTLER electronics GmbH
Junkersstr. 3, D-82178 Puchheim, Germany
-
A ZETTLER GROUP
Company
phone: +49 89 800 97-0 [email protected]
fax:
+49 89 800 97-200 www.ZETTLERelectronics.com
This product specification to be used only together with the application notes
which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf
2015-03-31
Similar pages