AVAGO AFCT-57F5ATMZ Fibre channel optical transceiver Datasheet

AFCT-57F5ATMZ
Digital Diagnostic SFP+, 1310 nm, 16 GFC [14.025/8.5/4.25 GBd]
Fibre Channel Optical Transceiver
Temperature Range 0 to 85 °C Tcase
D
MZ PRO
AT
F5 ER S 1
-57 AS S 5
CT m L LA 122 2K
AF 10n R(j) C
00
3
6
F
1 C A
25
21 HIN A12
C N: A
S
Data Sheet
Description
Features
Avago Technologies’ AFCT-57F5ATMZ optical transceiver
supports high speed serial links over single mode optical fiber at signalling rates up to 14.025 Gb/s (the serial
line rate of 16 GFC). The product is compliant with Small
Form Pluggable industry agreements SFP and SFP+ for
mechanical and low speed electrical specifications. High
speed electrical and optical specifications are compliant
with ANSI Fibre Channel FC-PI-5.
•
•
•
•
•
The AFCT-57F5ATMZ is a multi-rate 1310 nm transceiver
which ensures compliance with FC-PI-5 16 GFC, 8 GFC and
4 GFC specifications. Per the requirements of 16 GFC, an
internal clock and data recovery circuit (CDR) is present
on the electrical output of this transceiver. This CDR will
lock at 14.025Gb/s (16 GFC) but must be bypassed for operation at 8.5Gb/s (8 GFC) and 4.25Gb/s (4 GFC), accomplished by using Rate Select inputs to configure transmit
and receive sides. Transmitter and receiver can operate at
different data rates, as is often seen during Fibre Channel
speed negotiation.
Digital diagnostic monitoring information (DMI) is present
in the AFCT-57F5ATMZ per the requirements of SFF-8472,
providing real time monitoring information of transceiver
laser, receiver and environment conditions over a SFF8431 2-wire serial interface.
Related Products
• AFBR-57F5TPZ: 850 nm SFP for 16G/8G/4G Fibre Channel
• AFBR-57D7APZ: 850 nm SFP for 8G/4G/2G Fibre Channel
• AFCT-57D5ATPZ: 1310 nm SFP for 8G/4G/2G Fibre Channel
• AFCT-57D5ANPZ: 1310 nm SFP for 8G/4G/2G Fibre Channel
• AFBR-57R5APZ: 850 nm SFP for 4G/2G/1G Fibre Channel
• AFCT-57R5APZ: 1310 nm SFP for 4G/2G/1G Fibre Channel
• AFCT-57R5ATPZ: 1310 nm SFP for 4G/2G/1G Fibre Channel
• AFCT-57R5ANPZ: 1310 nm SFP for 4G/2G/1G Fibre Channel
•
•
•
•
•
•
•
•
Compliant to RoHS directives
1310nm Distributed Feedback Laser (DFB)
Class 1 eye safe per IEC60825-1 and CDRH
Wide temperature range (0 °C to 85 °C)
LC duplex connector optical interface conforming to
ANSI TIA/EIA604-10 (FOCIS 10A)
Diagnostic features per SFF-8472 “Diagnostic
Monitoring Interface for Optical Transceivers”
Enhanced operational features including EWRAP,
OWRAP and variable electrical EQ/emphasis settings
Real-time monitoring of:
- Transmitter average optical power
- Received average optical power
- Laser bias current
- Temperature
- Supply Voltage
SFP+ mechanical specifications per SFF-8432
Pull Tab delatch mechanism
SFP+ compliant low speed interface
Fibre Channel FC-PI-5 compliant high speed interface
- 1600- SM-LC-L, 800- SM-LC-L, 400-SM-LC-L
Fibre Channel FC-PI-5 compliant 10km link distances
Applications
•
•
•
•
•
•
Fibre Channel switches (director, stand alone, blade)
Fibre Channel Host Bus Adapters
Fibre Channel RAID controllers
Fibre Channel tape drive
Port side connections
Inter-switch or inter-chassis aggregated links
Post
Amp
Rx
CDR
Rx Vout &
Emphasis
ROSA
µcontroller
TOSA
Laser
Driver
SFP Connector
Pre
Amp
Tx Equalization
Figure 1. Transceiver functional diagram
Transmitter Section
Digital Diagnostics
The transmitter section includes a Transmitter Optical
SubAssembly (TOSA), laser driver circuit and an electrical
input stage with variable equalization controls. The TOSA
contains a 1310nm Distributed Feedback Laser (DFB) light
source with integral light monitoring function and imaging optics to assure efficient optical coupling to the LC
connector interface. The TOSA is driven by a laser driver
IC, which uses the differential output from an integral Tx
equalization stage to modulate and regulate DFB optical
power. Between the SFP electrical connector and Laser
Driver is a variable, I2C-bus controlled, equalization circuit
to optimize SFP performance with non-ideal incoming
electrical waveforms.
The AFCT-57F5ATPZ is compliant to the Diagnostic Monitoring Interface (DMI) defined in document SFF-8472.
These features allow the host to access, via I2C-bus, real
time diagnostic monitors of transmit optical power, received optical power, temperature, supply voltage and
laser operating current.
Receiver Section
The receiver section includes a Receiver Optical SubAssembly (ROSA), pre-amplification and post-amplification
circuit, Clock and Data Recovery Circuit and an electrical
output stage with variable emphasis controls. The ROSA,
containing a high speed PIN detector, pre-amplifier and
imaging optics efficiently couple light from the LC connector interface and perform an optical to electrical conversion. The resulting differential electrical signal passes
through a post amplification circuit and into a Clock and
Data Recovery circuit (CDR) for cleaning up accumulated
jitter. The resulting signal is passed to a high speed output
line driver stage with variable, I2C-bus controlled, emphasis settings allowing the host to optimize signal characteristics between the SFP and host ASIC. Note the Rx CDR is
engaged only with Rx_RATE=high (16 GFC) and bypassed
with Rx_RATE=low (8G/4G).
2
Low Speed Interfaces
Conventional low speed interface I/Os are available as
defined in documents SFF-8074 and SFF-8431 to manage
coarse and fine functions of the optical transceiver. On the
transmit side, a Tx_DISABLE input is provided for the host
to turn on and off the outgoing optical signal. A transmitter rate select control input, Tx_RATE, is provided to configure the transmitter stages for 16 GFC, 8 GFC or 4 GFC
operation (logic HIGH , reserved for 16 GFC, logic LOW ,
reserved for 8 GFC and 4 GFC). A transmitter fault indicator output, Tx_FAULT, is available for the SFP to signal a
host of a transmitter operational problem. A receiver rate
select control input, Rx_RATE, is provided to configure receiver stages for 16 GFC, 8 GFC or 4 GFC operation (logic
HIGH reserved for 16 GFC, logic LOW reserved for 8 GFC
and 4 GFC). A received optical power loss of signal indicator, RX_LOS, is available to advise the host of a receiver
operational problem.
Regulatory Compliance
The AFCT-57F5ATMZ complies with all applicable laws
and regulations as detailed in Table 1. Certification level is
dependent on the overall configuration of the host equip­
ment. The transceiver performance is offered as a figure of
merit to assist the designer.
Electrostatic Discharge (ESD)
Electromagnetic Interference (EMI)
The AFCT-57F5ATMZ is compatible with ESD levels found
in typical manufacturing and operating environments as
described in Table 1. In the normal handling and operation of optical transceivers, ESD is of concern in two circumstances.
Equipment incorporating gigabit transceivers is typically
subject to regulation by the FCC in the United States,
CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan.
The AFCT-57F5ATMZ’s compliance to these standards is
detailed in Table 1. The metal housing and shielded design of the AFCT-57F5ATMZ minimizes the EMI challenge
facing the equipment designer.
The first case is during handling of the transceiver before
it is inserted into an SFP compliant cage. To protect the
device, it is important to use normal ESD handling precautions. These include use of grounded wrist straps,
work-benches and floor wherever a transceiver is handled.
The second case to consider is static discharges to the
exterior of the host equipment chassis after installation.
If the optical interface is exposed to the exterior of host
equipment cabinet, the transceiver may be subject to system level ESD requirements.
EMI Immunity (Susceptibility)
Due to its shielded design, the EMI immunity of the AFCT57F5ATMZ exceeds typical industry standards.
Flammability
The AFCT-57F5ATMZ optical transceiver is made of metal
and high strength, heat resistant, chemical resistant and
UL 94 flame retardant plastic.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
JEDEC A114
to the Electrical Pins
Class 1 (> 2000 V)
>1000 V for high speed signal pins TD+/-, RD+/-
Electrostatic Discharge (ESD)
Variation of IEC 61000-4-2
to the Duplex LC Receptacle
Typically, no damage occurs with 25 kV when
the duplex LC connector receptacle is
contacted by a Human Body Model probe.
GR1089
10 contacts of 8 kV on the electrical faceplate
with device inserted into a panel.
Electrostatic Discharge (ESD)
Variation of IEC 801-2
to the Optical Connector
Air discharge of 15 kV (min.) contact to
connector without damage.
Electromagnetic Interference
(EMI)
FCC Class B
CENELEC EN55022 Class B
(CISPR 22A)
VCCI Class 1
System margins are dependent on customer
board and chassis design.
Immunity
Variation of IEC 61000-4-3
Typically shows no measurable effect from a
10 V/m field swept from 10 MHz to 1 GHz.
Laser Eye Safety and
US FDA CDRH
Equipment Type Testing
EN 60825-1:2007
EN 60950-1:2006+A11+A1+A12
Class 1 Laser product
Component Recognition
UL file 173874
Underwriters Laboratories and
Canadian Standards Association
Joint Component Recognition
for Information Technology
Equipment including Electrical
Business Equipment
RoHS Compliance
3
Less than 1000 ppm of cadmium, lead, mercury,
hexavalent chromium, polybrominated biphenyls,
and polybrominated biphenyl ethers.
Special Operation Functions
Electrical and optical high speed data “wrap” functions are enabled to assist with local host or remote diagnostic and
optimization sequences. Optical data wrap (OWRAP) takes a received optical signal through a CDR jitter cleanup and
retransmits it optically out. Electrical data wrap (EWRAP) takes an incoming electrical signal through a CDR jitter cleanup
and retransmits it electrically out. An optional pass-through function is available to transmit outbound the wrapped
information, controlled through I2C-bus commands.
Rx
CDR
ROSA
µcontroller
TOSA
Laser
Driver
Pre
Amp
Rx Vout &
Emphasis
Post
Amp
Rx
CDR
Rx Vout &
Emphasis
ROSA
µcontroller
TOSA
Laser
Driver
Tx Equalization
SFP Connector
Post
Amp
SFP Connector
Pre
Amp
Tx Equalization
Figure 2b. EWRAP Functionality (I2C-bus controlled)
Figure 2a. OWRAP Functionality (I2C-bus controlled)
The electrical SFP input stage (TD +/-) has been enhanced with features to allow host control and optimization of the
transceiver’s input equalization settings. The host can then select, in situ, the most appropriate SFP setting for a given
interconnect scenario.
Rx
CDR
ROSA
µcontroller
TOSA
Laser
Driver
Pre
Amp
Rx Vout &
Emphasis
Tx Equalization
Figure 2c. SFP Tx Variable Input Electrical EQ (I2C-bus controlled)
Post
Amp
Rx
CDR
Rx Vout &
Emphasis
ROSA
µcontroller
TOSA
Laser
Driver
SFP Connector
Post
Amp
SFP Connector
Pre
Amp
Tx Equalization
Figure 2d. SFP Rx Variable Output Electrical Emphasis (I2C-bus controlled)
The SFP electrical output stage (RD+/-) has been enhanced with variable output emphasis features to allow host control
and optimization of the receiver’s output settings. The host can then select, in situ, the most appropriate SFP setting for
a given interconnect scenario. To assist with optimizing the receiver output setting, the user can have data transmitted
by the SFP to a host ASIC by using EWRAP to loop back host generated traffic or can use a remotely generated optical
signal as a data source for SFP and interconnect training.
4
Table 2. Rate Select Function
Function
State
Explanation
Rx Rate
Select
RS(0)
High
Receive Rate Select HIGH engages the internal Rx CDR. The CDR will look for valid 16 GFC traffic
(14.025Gb/s coded with 64b/66b) and lock within 500 µs when found. Due to differences in coding and
bit rate, this CDR will not be able to lock on valid 8 GFC or 4 GFC traffic.
Receive Rate Select LOW bypasses the internal Rx CDR. This is intended for use only with 8 GFC and 4 GFC
traffic. When set low, the SFP behaves like a legacy SFP.
Transmit Rate Select HIGH optimizes the transmitter performance for 16 GFC traffic.
Transmit Rate Select LOW optmizes the transmitter performance for 4 GFC and 8 GFC traffic.
Low
Tx Rate
Select
RS(1)
High
Low
Note: During Fibre Channel Link Speed Negotiation sequences, the host will control Tx Rate and Rx Rate inputs separately to accomplish link initialization. Once speed negotiation is complete, it is expected both Tx Rate and Rx Rate will be placed in the same state by the host.
Tx Rate Select
VCC ,T
RS (1)
40 kΩ
10 kΩ
Tx DIS
Tx_DISABLE
Tx FAULT
Tx_FAULT
TD+
0.1 µF
100 Ω
TD0.1 µF
4.7 k to 10 kΩ
4.7 µH
0.1 µF
Tx EQ
LASER DRIVER
Rx CDR
POST AMPLIFIER
VCC ,T
22 µF
0.1 µF
3.3 V
SERDES IC
PROTOCOL IC
4.7 µH
0.1 µF
22 µF
0.1 µF
50 Ω
4.7 k to
10 kΩ
RD+
100 Ω
Rx LOS
0.1 µF
50 Ω
0.1 µF
RS (0)
Rx Rate Select
40 kΩ
3.3 V
GND,R
4.7 k to 10 kΩ
4.7 k to 10 kΩ
MOD_DEF0
4.7 k to 10 kΩ
MODULE DETECT
SCL
SDA
Figure 3. Typical application configuration.
4.7 µH
V CC T
0.1 µF
0.1 µF
22 µF
3.3 V
4.7 µH
V CC R
0.1 µF
22 µF
0.1 µF
HOST BOARD
NOTE: INDUCTORS MUST HAVE LESS THAN 1Ω SERIES RESISTANCE TO LIMIT VOLTAGE DROP TO THE SFP MODULE.
Figure 4. Recommended power supply filter.
5
VCC ,R
RD-
LOSS OF SIGNAL
SFP MODULE
VCC ,R
VCC ,R
MOD_DEF1
MOD_DEF2
Table 3. Pin Description
Pin
Name
Function/Description
Notes
1
VeeT
Transmitter Ground
2
TX_FAULT
Transmitter Fault Indication – High indicates a fault condition
Note 1
3
TX_DISABLE
Transmitter Disable – Module electrical input disables on high or open
Note 2
4
MOD-DEF2
Module Definition 2 – Two wire serial ID interface data line (SDA)
Note 3
5
MOD-DEF1
Module Definition 1 – Two wire serial ID interface clock line (SCL)
Note 3
6
MOD-DEF0
Module Definition 0 – Grounded in module (module present indicator)
Note 3
7
Rx Rate Select RS(0)
Receiver rate select. Logic High = 14.025 Gb/s, Logic Low = 8.5 Gb/s and 4.25 Gb/s
Note 8
8
RX_LOS
Loss of Signal – High indicates loss of received optical signal
Note 4
9
Tx Rate Select RS(1)
Transmitter rate select. Logic High = 14.025 Gb/s, Logic Low = 8.5 Gb/s and 4.25 Gb/s
Note 8
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Inverse Received Data Out
Note 5
13
RD+
Received Data Out
Note 5
14
VeeR
Receiver Ground
15
VccR
Receiver Power + 3.3 V
Note 6
16
VccT
Transmitter Power + 3.3 V
Note 6
17
VeeT
Transmitter Ground
18
TD+
Transmitter Data In
Note 7
19
TD-
Inverse Transmitter Data In
Note 7
20
VeeT
Transmitter Ground
Notes:
1. TX_FAULT is an open collector/drain output, which must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
2. TX_DISABLE is an input that is used to shut down the transmitter optical output. It is internally pulled up (within the transceiver) with a 6.8 kΩ
resistor.
Low (0 – 0.8 V):
Transmitter on
Between (0.8 V and 2.0 V):
Undefined
High (2.0 – Vcc max) or OPEN: Transmitter Disabled
3. The signals Mod-Def 0, 1, 2 designate the two wire serial interface pins. They must be pulled up with a 4.7 k – 10 kΩ resistor on the host board.
Mod-Def 0 is grounded by the module to indicate the module is present
Mod-Def 1 is serial clock line (SCL) of two wire serial interface
Mod-Def 2 is serial data line (SDA) of two wire serial interface
4. RX_LOS (Rx Loss of Signal) is an open collector/drain output that must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high, this
output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal
operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+ designate the differential receiver outputs. They are AC coupled 100 Ω differential lines which should be terminated with 100 Ω differential
at the host SERDES input. AC coupling is done inside the transceiver and is not required on the host board. The voltage swing on these lines will
be between 370 and 850 mV differential (185 – 425 mV single ended) when properly terminated.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined at the SFP connector pin. The maximum supply current is 300 mA
and the associated in-rush current will typically be no more than 30 mA above steady state after 2 microseconds.
7. TD-/+ designate the differential transmitter inputs. They are AC coupled differential lines with 100 Ω differential termination inside the module.
The AC coupling is done inside the module and is not required on the host board. The inputs will accept differential swings of 180 – 1200 mV (90
– 600 mV single ended)
8. Rate_Select is an input that is used to control transmit and receive high speed parametric optimizaton. It is internally pulled down (within the
transceiver) with a 40kOhm resistor.
Low (0 - 0.8V) or Open:
Rate is set to 8.5Gb/s and below optimization. For Rx Rate_Select, the internal CDR is bypassed.
Between (0.8V and 2.0V)
Undefined
High (2.0 - Vcc max):
Rate is set to 14.025Gb/s optimization. For Rx Rate_Select, the internal CDR is engaged.
6
Table 4. Absolute Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Storage Temperature
TS
-40
85
C
Note 1, 2
Case Operating Temperature
TC
-40
85
C
Note 1, 2
Relative Humidity
RH
5
95
%
Note 1
Supply Voltage
VccT, R
-0.5
3.8
V
Note 1, 2, 3
Low Speed Input Voltage
VIN
-0.5
Vcc+0.5
V
Note 1
Notes;
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
period of time. See Reliability Data Sheet for specific reliability performance.
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is
not implied, and damage to the device may occur over an extended period of time.
3. The module supply voltages, VCCT and VCCR must not differ by more than 0.5 V or damage to the device may occur.
Table 5. Recommended Operating Conditions
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Case Operating Temperature
TC
0
85
°C
Note 1, 2
Supply Voltage
VccT, R
3.135
3.465
V
Note 2
4.25
14.025
Gb/s
Note 2
Data Rate Notes:
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
thermal design.
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 6. Transceiver Electrical Characteristics
(TC = 0 °C to 85 °C, VccT, VccR = 3.3 V ± 5%)
Parameter
Symbol
Minimum
Typical
Maximum
PSNR
100
Unit
Notes
AC Electrical Characteristics
Power Supply Noise Rejection (peak-peak)
mV
Note 1
DC Electrical Characteristics
Module Supply Current
ICC 330
mA
Low Speed Outputs:
VOH
2.0 VccT,R+0.3
V
VOL
0.8
V
VIH
2.0
Vcc
V
VIL
0
0.8
V
Transmit Fault (TX_FAULT), Loss of Signal
(RX_LOS), MOD-DEF 2
Low Speed Inputs:
Transmit Disable (TX_DIS), MOD-DEF 1,
MOD-DEF2, RS(0), RS(1)
Notes:
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
3. Mod-Def1 and Mod-Def2 must be pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
7
Note 2
Note 3
Table 7. Transmitter and Receiver Electrical Characteristics
(Tc = 0 °C to 85 °C, VccT, VccR = 3.3 V ± 5%)
Parameter
Symbol
Min
High Speed Data Input Transmitter Differential
Input Voltage (TD+/-)
VI
High Speed Data Output Receiver Differential
Output Voltage (RD+/-)
Vo
Receiver Total Jitter (14.025 Gb/s)
Typ
Max
Unit
Notes
180
1200
mV
Note 1
370
850
mV
Note 2
TJ
0.36
UI
Note 3, Rx_Rate = high
Receiver Total Jitter (8.5 Gb/s)
TJ
0.71
UI
Note 4, Rx_Rate = low
Receiver Contributed Total Jitter (4.25 Gb/s)
TJ
0.26
UI
Note 4, Rx_Rate = low
Receiver Deterministic Jitter (14.025 Gb/s)
DJ
0.22
UI
Note 3, Rx_Rate = high
Receiver Deterministic Jitter (8.5 Gb/s)
DJ
0.42
UI
Note 4, Rx_Rate = low
Receiver Contributed Deterministic Jitter (4.25
Gb/s)
DJ
0.10
UI
Note 4, Rx_Rate = low
Receiver Data Dependent Pulse Width Shrinkage
(14.025 Gb/s)
DDPWS
0.14
UI
Note 3, Rx_Rate = high
Receiver Data Dependent Pulse Width Shrinkage
(8.5 Gb/s)
DDPWS
0.36
UI
Note 4, Rx_Rate = low
Notes:
1. Internally ac coupled and terminated (100Ω differential).
2. Internally ac coupled but requires an external load termination (100Ω differential).
3. CDR is engaged with Rx_Rate = high. Received output jitter for 14.025 Gb/s.
4. CDR is not engaged with Rx_Rate = low (ie. Bypassed). Receiver output jitter for 8.5 Gb/s and 4.25Gb/s.
Table 8. Transmitter Optical Characteristics
(Tc = 0 °C to 85 °C, VccT, VccR = 3.3V ± 5%)
Parameter
Symbol
Min
Unit
Notes
Modulated Optical Output Power (OMA)
(Peak to Peak) 14.025 Gb/s
Tx,OMA
631
uW
TxRate=High
Modulated Optical Output Power (OMA)
(Peak to Peak) 8.5 Gb/s, 4.25 Gb/s
Tx,OMA
290
uW
TxRate=Low
Average Optical Output Power 14.025 Gb/s
Pout
-5.0
dBm
Note 1, TxRate=High
Average Optical Output Power 8.5 Gb/s, 4.25 Gb/s
Pout
-8.4
dBm
Note 1, TxRate=Low
Center Wavelength
lc
1295
-20 dB Spectral Width
-20 dB
Side Mode Suppression
Typ
Max
1325
nm
1.0
nm
30
dB
RIN12 (OMA)
RIN
-130
dB/Hz
Transmitter Distortion Penalty, 14.025 Gb/s
TDP
4.4
dB
TxRate=High
Transmitter Distortion Penalty, 8.5 Gb/s
TDP
3.2
dB
TxRate=Low
Tx Optical Rise/Fall Time (20% - 80%), 4.25Gb/s
Tr, Tf
90
ps
TxRate=Low
Transmitter Contributed Jitter, 4.25 Gb/s
TJ
0.25
UI
TxRate=Low
Pout Tx_DISABLE Asserted
Poff
-35
dBm
Notes:
1. Max Pout is the lesser of Class 1 safety limits (CDRH and EN 60825) or received power, max.
8
Table 9. Receiver Optical and Electrical Characteristics
(Tc = 0 °C to 85 °C, VccT, VccR = 3.3 V ± 5%)
Parameter
Symbol
Min
Receiver Optical Center Wavelength
lc
1260
Optical Input Power, 14.025 Gb/s
Max
Unit
1370
nm
PIN
+2.0
dBm,avg
RxRate=High
Optical Input Power, 8.5 Gb/s
PIN
+0.5
dBm,avg
RxRate=Low
Optical Input Power, 4.25 Gb/s
PIN
-1.0
dBm,avg
RxRate=Low
Input Optical Modulation Amplitude, 14.025 Gb/s
(Peak to Peak) [Unstressed Sensitivity]
OMA
63
uW,OMA
Note 1
Input Optical Modulation Amplitude, 8.5 Gb/s
(Peak to Peak) [Unstressed Sensitivity]
OMA
42
uW,OMA
Note 1
Input Optical Modulation Amplitude, 4.25 Gb/s
(Peak to Peak) [Unstressed Sensitivity]
OMA
29
uW,OMA
Note 1
12
dB
Return Loss
Loss of Signal – Assert
Pa
Loss of Signal – De-asserted
PD
Loss of Signal – Hysteresis
PA – PD
Typ
-28
dBm,OMA
-16
0.5
dBm,OMA
dB
Notes:
1. Input Optical Modulation Amplitude (commonly known as sensitivity] requires a valid Fibre Channel encoded input.
9
Notes
Table 10. Transceiver DIAGNOSTIC Timing Characteristics
(TC = 0 °C to 85 °C, VccT, VccR = 3.3 V ± 5%)
Parameter
Symbol
Hardware TX_DISABLE Assert Time
Minimum
Maximum
Unit
Notes
t_off
10
µs
Note 1
Hardware TX_DISABLE Negate Time
t_on
1
ms
Note 2
Time to initialize, including reset of TX_FAULT
t_init
300
ms
Note 3
Hardware TX_FAULT Assert Time
t_fault
1000
µs
Note 4
Hardware TX_DISABLE to Reset
t_reset
µs
Note 5
Hardware RX_LOS Deassert Time
t_loss_on
100
µs
Note 6
Hardware RX_LOS Assert Time
t_loss_off
100
µs
Note 7
Software TX_DISABLE Assert Time
t_off_soft
100
ms
Note 8
Software TX_DISABLE Negate Time
t_on_soft
100
ms
Note 9
Software Tx_FAULT Assert Time
t_fault_soft
100
ms
Note 10
Software Rx_LOS Assert Time
t_loss_on_soft
100
ms
Note 11
Software Rx_LOS Deassert Time
t_loss_off_soft
100
ms
Note 12
Analog parameter data ready
t_data
1000
ms
Note 13
Serial bus hardware ready
t_serial
300
ms
Note 14
Serial Bus Buffer Time
t_buf
µs
Note 16
Write Cycle Time
t_write
40
ms
Note 15
Serial ID Clock Rate
f_serial_clock
400
kHz
10
20
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal.
Measured from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1 – 4 byte write command. Write cycle time is 80 ms max. for a 5 – 8 byte write.
16. Time between STOP and START Commands.
10
Table 11. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
(TC = 0 °C to 85 °C, VccT, VccR = 3.3 V ± 5%)
Parameter
Symbol
Min.
Units
Notes
Transceiver Internal Temperature
Accuracy
TINT
±3.0
°C
Temperature is measured internal to the transceiver.
Valid from = 0 °C to 85 °C case temperature.
Transceiver Internal Supply
Voltage Accuracy
VINT
±0.1
V
Supply voltage is measured internal to the transceiver
and can, with less accuracy, be correlated to
voltage at the SFP Vcc pin. Valid over 3.3 V ± 5%.
Transmitter Laser DC Bias Current
Accuracy
IINT
±10
%
IINT is better than ±10% of the nominal value.
Transmitted Average Optical
Output Power Accuracy
PT
±3.0
dB
Coupled into single-mode fiber. Valid from
144 µW to 1584 µW, avg.
Received Average Optical Input
Power Accuracy
PR
±3.0
dB
Coupled from single-mode fiber. Valid from
24 µW to 1584 µW, avg.
V CC T,R > 2.97 V
V CC T,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_init
t_init
t-init: TX DISABLE NEGATED
t-init: TX DISABLE ASSERTED
V CC T,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_off
t_init
t_on
INSERTION
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
OCCURANCE OF FAULT
OCCURANCE OF FAULT
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_fault
t_reset
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
t_init*
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
OCCURANCE OF FAULT
TX_FAULT
LOS
TRANSMITTED SIGNAL
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t_reset
t_fault
t_loss_on
t_init*
t-fault: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL NOT RECOVERED
Figure 4. Transceiver timing diagrams (module installed except where noted).
11
OCCURANCE
OF LOSS
OPTICAL SIGNAL
TX_DISABLE
t-loss-on & t-loss-off
t_loss_off
Table 12. EEPROM Serial ID Memory Contents – Base SFP Memory (Address A0h)
Byte #
Decimal
Data
Hex Notes
Byte #
Decimal
Data
Hex
Notes
0
1
2
3
4
5
6
7
03
04
07
00
00
00
00
12
37
38
39
40
41
42
43
44
00
17
6A
41
46
43
54
2D
Hex Byte of Vendor OUI [2]
Hex Byte of Vendor OUI [2]
Hex Byte of Vendor OUI [2]
"A" - Vendor Part Number ASCII character
"F" - Vendor Part Number ASCII character
"C" - Vendor Part Number ASCII character
"T" - Vendor Part Number ASCII character
"-" - Vendor Part Number ASCII character
8
9
10
11
00
01
70
06
45
46
47
48
35
37
46
35
"5" - Vendor Part Number ASCII character
"7" - Vendor Part Number ASCII character
"F" - Vendor Part Number ASCII character
"5" - Vendor Part Number ASCII character
12
8C
49
41
"A" - Vendor Part Number ASCII character
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0A
0A
64
00
00
00
00
41
56
41
47
4F
20
20
20
20
"A" - Vendor Part Number ASCII character
"V" - Vendor Part Number ASCII character
"A" - Vendor Part Number ASCII character
"G" - Vendor Part Number ASCII character
"O" - Vendor Part Number ASCII character
“ ” - Vendor Name ASCII character
“ ” - Vendor Name ASCII character
“ ” - Vendor Name ASCII character
“ ” - Vendor Name ASCII character
50
5A
52
53
54
55
56
57
58
59
60
61
62
63
64
65
54
4D
5A
20
20
20
20
20
20
20
05
1E
00
"T" - Vendor Part Number ASCII character
"M" - Vendor Part Number ASCII character
"Z" - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
“ ” - Vendor Part Number ASCII character
Hex Byte of Laser Wavelength [3]
Hex Byte of Laser Wavelength [3]
29
30
31
32
33
34
20
20
20
20
20
20
“
“
“
“
“
“
66
67
68-83
84-91
92
93
00
00
35
36
20
00
“ ” - Vendor Name ASCII character
94
95
96-255
05
SFP physical device
SFP function defined by serial ID only
LC optical connector
Long distance (per FC-PI-5),
Longwave Laser (LC)
Single mode optical media
400, 800 & 1600 Mbyte/s FC-PI-5 speed [1]
64b/66b for 16 GFC & 8b/10b for 8 GFC and
4 GFC
140 x 100 Mbit/s nominal bit rate
(14.025 Gbit/s)
16/8/4G Independent Tx and Rx Rate Selects
10km of single mode fiber
10km of single mode fiber
” - Vendor Name ASCII character
” - Vendor Name ASCII character
” - Vendor Name ASCII character
” - Vendor Name ASCII character
” - Vendor Name ASCII character
” - Vendor Name ASCII character
Checksum for Bytes 0-62 [4]
00
3A
68
FA
Hardware SFP TX_DISABLE, TX_FAULT &
RX_LOS, RATE_SELECT
Vendor Serial Number ASCII characters [5]
Vendor Date Code ASCII characters [6]
Digital Diagnostics, Internal Cal, Rx Pwr Avg
A/W, Soft SFP TX_DISABLE, TX_FAULT &
RX_LOS, RATE_SELECT
SFF-8472 Compliance to revision 10.5
Checksum for Bytes 64-94 [4]
00
Notes:
1. 16 GFC [1600 MBytes/sec] is a serial bit rate of 14.025 Gb/s with 64b/66b. 8 GFC [800 Mbyte/s] is 8.5Gb/s and 4 GFC [400 Mbyte/s] is 4.25 Gb/s
with 8b/10b.
2. The IEEE Organizationally Unique Identifier (OUI) assigned to AVAGO Technologies is 00-17-6A (3 bytes of hex).
3. Laser wavelength is represented in 16 unsigned bits. The hex representation of 1310 (nm) is 051E.
4. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
5. Addresses 68-83 specify the AFCT-57F5ATMZ ASCII serial number and will vary on a per unit basis.
6. Addresses 84-91 specify the AFCT-57F5ATMZ ASCII date code and will vary on a per date code basis.
12
Table 13. EEPROM Serial ID Memory Contents - Enhanced SFP Memory (Address A2h)
Byte #
Decimal
Notes
Byte #
Decimal
Notes
Byte #
Decimal
Notes
0
Temp H Alarm MSB [1]
23
Tx Bias L Warning LSB [3]
99
Real Time Vcc LSB [2]
1
Temp H Alarm LSB [1]
24
Tx Power H Alarm MSB [4]
100
Real Time Tx Bias MSB [3]
2
Temp L Alarm MSB [1]
25
Tx Power H Alarm LSB [4]
101
Real Time Tx Bias LSB [3]
3
Temp L Alarm LSB [1]
26
Tx Power L Alarm MSB [4]
102
Real Time Tx Power MSB [4]
4
Temp H Warning MSB [1]
27
Tx Power L Alarm LSB [4]
103
Real Time Tx Power LSB [4]
5
Temp H Warning LSB [1]
28
Tx Power H Warning MSB [4]
104
Real Time Rx Power MSB [5]
6
Temp L Warning MSB [1]
29
Tx Power H Warning LSB [4]
105
Real Time Rx Power LSB [5]
7
Temp L Warning LSB [1]
30
Tx Power L Warning MSB [4]
106
Reserved
8
Vcc H Alarm MSB [2]
31
Tx Power L Warning LSB [4]
107
Reserved
9
Vcc H Alarm LSB [2]
32
Rx Power H Alarm MSB [5]
108
Reserved
10
Vcc L Alarm MSB [2]
33
Rx Power H Alarm LSB [5]
109
Reserved
11
Vcc L Alarm LSB [2]
34
Rx Power L Alarm MSB [5]
110
Status/Control – See Table 14
12
Vcc H Warning MSB [2]
35
Rx Power L Alarm LSB [5]
111
Status/Control – See Table 15
13
Vcc H Warning LSB [2]
36
Rx Power H Warning MSB [5]
112
Flag Bits – See Table 16
14
Vcc L Warning MSB [2]
37
Rx Power H Warning LSB [5]
113
Flag Bits – See Table 16
15
Vcc L Warning LSB [2]
38
Rx Power L Warning MSB [5]
114
Reserved
16
Tx Bias H Alarm MSB [3]
39
Rx Power L Warning LSB [5]
115
Reserved
17
Tx Bias H Alarm LSB [3]
40-55
Reserved
116
Flag Bits – See Table 16
18
Tx Bias L Alarm MSB [3]
56-94
External Calibration Constants [6]
117
Flag Bits – See Table 16
19
Tx Bias L Alarm LSB [3]
95
Checksum for Bytes 0-94 [7]
118
Status/Control – See Table 17
20
Tx Bias H Warning MSB [3]
96
Real Time Temperature MSB [1]
119-127
Reserved
21
Tx Bias H Warning LSB [3]
97
Real Time Temperature LSB [1]
128-247
Customer Writable – See Table 18
22
Tx Bias L Warning MSB [3]
98
Real Time Vcc MSB [2]
248-255
Vendor Specific
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed two’s complement integer in increments of 1/256 °C.
2. Supply Voltage (Vcc) is decoded as a 16 bit unsigned integer in increments of 100 V.
3. Tx bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 A.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 W.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 W.
6. Bytes 56-94 are not intended for use, but have been set to default values per SFF-8472.
7. Byte 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
Table 14. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 110)
Bit #
Status/Control Name
Description
Notes
7
TX_DISABLE State
Digital state of TX_DISABLE Input Pin (1 = TX_DISABLE asserted)
Note 1
6
Soft TX_DISABLE Control
Read/write bit for changing digital state of TX_DISABLE function
Note 1, 2
5
RS(1) State
Digital state of TX Rate_Select Input Pin RS(1) (1 = Rate High asserted)
4
RS(0) State
Digital state of RX Rate_Select Input Pin RS(0) (1 = Rate High asserted)
3
Soft RS(0) Control
Read/write bit for changing digital state of Rx Rate_Select RS(0) function
Note 3
2
TX_FAULT State
Digital state of TX_FAULT Output Pin (1 = TX_FAULT asserted)
Note 1
1
RX_LOS State
Digital state of SFP RX_LOS Output Pin (1 = RX_LOS asserted)
Note 1
0
Data Ready (Bar)
Indicates transceiver is powered and real time sense data is ready
(0 = Data Ready)
Notes:
1. The response time for soft commands of the AFCT-57F5ATMZ is 100 msec as specified by MSA SFF-8472.
2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3 …. either asserted will disable the SFP transmitter.
3. Bit 3 is logic OR’d with the SFP RS(0) RX Rate_Select input pin 7 …. either asserted will set receiver to Rate = High.
13
Table 15. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 111)
Byte 111 <3:0> (Bin)
Name
1100
OWRAP FORWARD When enabled, OWRAP FORWARD routes incoming SFP Rx optical data to both the
Tx optical output and the Rx electrical output.
0100
OWRAP
When enabled, OWRAP routes incoming SFP Rx optical data to the Tx optical
output.
0011
EWRAP FORWARD
When enabled, EWRAP FORWARD routes incoming SFP Tx electrical data to both
Rx electrical utput and Tx optical output.
0001
EWRAP
When enabled, EWRAP routes incoming SFP Tx electrical data to the Rx electrical
output.
0000
RESET
Disable any EWRAP/OWRAP mode.
Any settings other than Invalid
those reported above
Description
Any invalid setting is ignored and leaves unchanged the previous EWRAP/OWRAP
mode.
Table 16. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117)
Byte
Bit
Flag Bit Name
Description
112
7
Temp High Alarm
Set when transceiver internal temperature exceeds high alarm threshold
6
Temp Low Alarm
Set when transceiver internal temperature exceeds low alarm threshold
5
Vcc High Alarm
Set when transceiver internal supply voltage exceeds high alarm threshold
4
Vcc Low Alarm
Set when transceiver internal supply voltage exceeds low alarm threshold
3
Tx Bias High Alarm
Set when transceiver laser bias current exceeds high alarm threshold
2
Tx Bias Low Alarm
Set when transceiver laser bias current exceeds low alarm threshold
1
Tx Power High Alarm
Set when transmitted average optical power exceeds high alarm threshold
0
Tx Power Low Alarm
Set when transmitted average optical power exceeds low alarm threshold
7
Rx Power High Alarm
Set when received average optical power exceeds high alarm threshold
6
Rx Power Low Alarm
Set when received average optical power exceeds low alarm threshold
0-5
Reserved
7
Temp High Warning
Set when transceiver internal temperature exceeds high warning threshold
6
Temp Low Warning
Set when transceiver internal temperature exceeds low warning threshold
5
Vcc High Warning
Set when transceiver internal supply voltage exceeds high warning threshold
4
Vcc Low Warning
Set when transceiver internal supply voltage exceeds low warning threshold
3
Tx Bias High Warning
Set when transceiver laser bias current exceeds high warning threshold
2
Tx Bias Low Warning
Set when transceiver laser bias current exceeds low warning threshold
1
Tx Power High Warning
Set when transmitted average optical power exceeds high warning threshold
0
Tx Power Low Warning
Set when transmitted average optical power exceeds low warning threshold
7
Rx Power High Warning
Set when received average optical power exceeds high warning threshold
6
Rx Power Low Warning
Set when received average optical power exceeds low warning threshold
0-5
Reserved
113
116
117
14
Table 17. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 118).
Bit #
Status/Control Name
4-7
Reserved
Description
Notes
3
Soft RS(1) Control
2
Reserved
Read/write bit for changing digital state of Tx Rate_Select RS(1) function
Note 1
1
Power Level State
Always set to zero., which indicates Power Level 1 operation (1 W max)
0
Power Level Select
Unused. This device supports power level zero (1 W max) only.
Notes:
1. Bit 3 is logic OR’d with the SFP RS(1) TX Rate_Select input pin 9 …. either asserted will set transmitter to Rate = High.
Table. 18. Signal Integrity Feature Configuration Bytes (2-Wire Address A2h)
Byte
Name
Description
40
Tx Input EQ Setting for
RS(1) = High
Defines SFP incoming electrical Tx equalization setting for Tx_Rate = High [i.e., RS(1)=High]
The SFP transceiver will support 8 EQ settings in the lower 3 bits of this byte. EQ can be
varied from 0 dB to 9 dB gain at 7 GHz in eight non-linear steps. The value of 0 results in
0 dB emphasis. Writing FFh to this byte and power cycling both reset the byte to factory
settings, which is 02h.
41
Tx Input EQ Setting for
RS(1) = Low
Defines SFP incoming electrical Tx equalization setting for Tx_Rate = Low [i.e., RS(1)=Low]
The SFP transceiver will support 8 EQ settings in the lower 3 bits of this byte. EQ can be
varied from 0 dB to 9 dB gain at 7 GHz in eight non-linear steps. The value of 0 results in
0 dB emphasis. Writing FFh to this byte and power cycling both reset the byte to factory
settings, which is 04h.
42
Rx Output Pre Emphasis
Setting for RS(0) = High
Defines SFP output electrical Rx pre-emphasis setting for Rx_Rate = High [i.e., RS(0)=High]
The SFP transceiver will support 16 Pre Emphasis settings in the lower 4 bits of this byte.
Emphasis can be varied from 0 dB to 9 dB in sixteen non-linear steps. The value of 0 results
in 0 dB emphasis. Writing FFh to this byte resets to factory settings. Writing FFh to this byte
and power cycling both reset the byte to factory settings, which is 04h.
43
Rx Output Pre Emphasis
Setting for RS(0) = Low
Defines SFP output electrical Rx pre-emphasis setting for Rx_Rate = Low [i.e., RS(0)=Low]
The SFP transceiver will support 16 Pre Emphasis settings in the lower 4 bits of this byte.
Emphasis can be varied from 0 dB to 9 dB in sixteen non-linear steps. The value of 0 results
in 0 dB emphasis. Writing FFh to this byte resets to factory settings. Writing FFh to this byte
and power cycling both reset the byte to factory settings, which is 02h.
44-55
Unallocated
Contents 00h.
Note: Checksum at address A2h byte 95 will be updated within 100 ms of a value change in these bytes.
15
8.9
47.5
13.9
0.77 UNCOMPRESSED
6.25
12.95
8.55
13.65
13.46
Figure 6. Module drawing
Figure 7. Product Label
For product information and a complete list of distributors, please go to our website:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved.
AV02-3556EN - May 6, 2014